Hatari HT-T16M4 User manual

PRODUCT SPECIFICATIONS
Model
Size
Voltage
Electric Power
Electric Current
Service Value
HT-T16M4
400 mm
220-240V 50/60Hz
52W
0.23A
1.30 m3/min/W
Item code: 1002347 REV.02
User Manual
Table Fan
Model: HT-T16M4

1 2
Unplug the power supply cord before cleaning or changing the components, and when not in use for a long period of time.
Do not use the fan if components are not assembled fully or properly, or if a component such as blade, grille, or blade cap is
damaged.
The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
CAUTION
1.
2.
3.
4.
5.
6.
USAGE RECOMMENDATIONS
The fan components should be assembled correctly according to the manual to prevent possible harm that may occur while in
use.
The fan should not be placed or installed in areas that are of extreme temperatures or near stoves, or in areas that are wet with
high humidity, or has hydrocarbon vapors such as petroleum.
The fan should not be operated near curtains or mosquito nets because the fan may suck in the light material and entangle
them with the blades, possibly causing harm.
Do not spray all types of spray into the fan; for example, hairspray or cleaning spray.
Do not insert fingers, pencils or other objects into the grille while the blades are spinning as it may result in possible injury or
physical damage.
If a component such as blade, grille, blade cap, or the back grille lock is damaged, replacement can be made using a new
component. please refer to the assembly instructions.
If an electrical component such as supply cord, motor, or switch is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard. It is not advisable to fix the fan at home
1.
2.
3.
4.
5.
6.
7.
DIRECTION OF USE
Fan speed adjustment
Swing adjustment
Fan angle adjustment
3 adjustable fan speed settings 0: off, 1: low speed, 2: medium speed, 3: high speed
Push the oscillation knob down to activate left-right movements. Pull the oscillation know up to cease
movement.
Tilt the grille upwards or downwards according to the desired wind direction.
1.
2.
3.
Plug power supply cord into a 220-240V, 50/60Hz power socket.
CARE AND CLEANING INSTRUCTIONS
Use a damp cloth to wipe stains, and then dry the area by wiping.
When cleaning the fan, be careful not to let the wire, switch, motor and other electrical components get wet.
Do not use chemical products, thinner solvents, alcohol, kerosene or petrol to clean the fan.
1.
2.
3.
51 2 3 6 7 9
4
10 11
12
13
14
16
15
8
FAN COMPONENTS
DECO
FRONT GRILLE
GRILLE RING
GRILLE CLIP
BLADE CAP
FAN BLADE
BACK GRILLE LOCK
BACK GRILLE CLIP LOCK
BACK GRILLE
FRONT MOTOR COVER
OSCILLATION KNOB
BACK MOTOR COVER
NECK JOINT SET
STAND
FAN SPEED BUTTONS
POWER SUPPLY CORD & PLUG
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
2
Loosen the back grille lock by twisting it in
the direction as shown by the arrow
(LOOSEN).
5Assemble the front grille with the catch
on the grille ring interlocking with the
back grille clip lock. Press the grille ring
in all directions then push the grille clip
up.
ASSEMBLY INSTRUCTIONS
Place the blade onto the motor shaft,
ensuring that grooves of the blade fit
with the motor shaft pin. Place the blade
cap over the blade and tighten it by
twisting in the direction as shown by the
arrow (TIGHTEN).
4
Loosen the blade cap by twisting it in the
direction as shown by the arrow
(LOOSEN).
1
1
Assemble the back grille as shown in the
diagram. Place the back grille lock over the
grille and tighten it by twisting in the
direction as shown by the arrow
(TIGHTEN).
Plug in the fan and press the fan speed button 1, 2, 3
respectively. If the fan makes a loud noise, check if the blade
cap is screwed on tightly and whether the grooves of the blade
fit the corresponding motor shaft pin.
3
3