Hatco IR1-3000 User manual

© 2010 atco Corporation
9/@.?4:9$,920>
$%0=40>
9>?,77,?4:9,9/";0=,?492 ,9@,7
:= :/07>
I&W #07.05.258.00
:9:?:;0=,?0?34>0<@4;809?@970>>D:@3,A0
=0,/,9/@9/0=>?::/?30.:9?09?>:1?34>8,9@,7
,47@=0?:1:77:B?3049>?=@.?4:9>.:9?,490/49?34>
8,9@,78,D=0>@7?49>0=4:@>495@=D:=/0,?3&34>
8,9@,7 .:9?,49> 48;:=?,9? >,10?D 491:=8,?4:9
.:9.0=9492?308,49?09,9.0@>0,9/:;0=,?4:9
:1?34>;=:/@.?1D:@M=0@9,-70?:@9/0=>?,9/?30
.:9?09?> :1 ?34> 8,9@,7 ;70,>0 -=492 4? ?: ?30
,??09?4:9:1D:@=>@;0=A4>:=00;?34>8,9@,749
,>,107:.,?4:91:=1@?@=0=010=09.0
!::;0=00>?00<@4;:,7809:><@03,D,70F/:D
.:8;=09/4/: 07 .:9?094/: /0 0>?0 8,9@,7
@,7<@40= 1,77, 09 07 >02@48409?: /0 7,>
49>[email protected]:90>.:9?094/,>090>?08,9@,7;@0/0
=0>@7?,=09@9>0=4:70>4G9:8@0=?0>?08,9@,7
.:9?409048;:=?,9?0491:=8,.4G9>:-=0>02@=4/,/
.:9.0=9409?0,78,9?0948409?:@>:D:;0=,.4G9
/00>?0;=:/@.?:%4@>?0/9:;@0/009?09/0=07
.:9?094/:/00>?08,9@,7;:=1,A:=;=02@9?0,>@
>@;0=A4>:= 78,.09,= 0>?0 8,9@,7 09 @9,
7:.,74E,.4G9>02@=,;,=,7,=010=09.4,1@?@=,
$024>?0=D:@=@94?:97490
See IMPORTANT OWNER INFORMATION
section for details.

Form No. IR1CEM-0910
2
"!&!&%
This manual provides the installation, safety, and operating
instructions for atco Induction Ranges. atco recommends all
installation, operating, and safety instructions appearing in this
manual be read prior to installation or operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
)$!! 49/4.,?0> , 3,E,=/:@> >4?@,?4:9 B34.3 41 9:?
,A:4/0/.:@7/=0>@7?49/0,?3:=>0=4:@>495@=D
'&"! 49/4.,?0> , 3,E,=/:@> >4?@,?4:9 B34.3 41 9:?
,A:4/0/.:@7/=0>@7?49849:=:=8:/0=,?0495@=D
!"&4>@>0/?:,//=0>>;=,.?4.0>9:?=07,?0/?:;0=>:9,7
495@=D
NOTICE
CAUTION
WARNING
!&$"'&"!
atco Induction Ranges offer a safe, quick, efficient, and
attractive way to prepare foods in commercial kitchens as well
as display cooking locations (omelet bars, buffets, etc...). The
high efficiency, accuracy, and speed of induction cooking make
atco Induction Ranges the perfect choice for quality
foodservice organizations.
Induction cooking relies on the creation of a magnetic field
between the induction coils below the glass surface of the unit
and an “induction-ready” pan sitting on top of the glass surface.
This magnetic field generates induction currents in the base of
the pan, which heat the pan instantly. That heat then is
transferred to the pan contents. Since the magnetic field exists
only between the induction coils and a magnetic material
(ferrous material), the glass surface between the two does not
become heated, eliminating heat loss and increasing efficiency.
When the magnetic field is “broken” by turning off the unit or
removing the pan, heat generation stops instantly.
atco Induction Ranges are products of extensive research and
field testing. The materials used were selected for maximum
durability, attractive appearance, and optimum performance.
Every unit is inspected and tested thoroughly prior to shipment.
8;:=?,9?"B90=91:=8,?4:9
9?=:/@.?4:9
8;:=?,9?%,10?D91:=8,?4:9
:/070>.=4;?4:9
:/070>429,?4:9
%;0.414.,?4:9>
Plug Configurations .........................................................5
Electrical Rating Chart.....................................................5
Dimensions — Model IR1-3000 ......................................5
Dimensions — Model IRB1-3000 ....................................6
Dimensions — Model IRW1-3000 ...................................6
9>?,77,?4:9
General............................................................................7
Installing Built-In Models..................................................7
";0=,?4:9
General............................................................................8
,49?09,9.0
General............................................................................9
Daily Cleaning .................................................................9
Cleaning the Air Inlet Filter ..............................................9
&=:@-70>3::?492@4/0
484?0/),==,9?D
%0=A4.091:=8,?4:9
#"$&!&")!$!"$ &"!
Record the model number, serial number (located on the
bottom of the unit), voltage, and purchase date of the unit in
the spaces below. Please have this information available when
calling atco for service assistance.
Model No. ____________________________________
Serial No. ____________________________________
Voltage ______________________________________
Date of Purchase ______________________________
$024>?0=D:@=@94?
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the atco website at
BBB3,?.:.:=;.:8, select the Parts & S rvic pull-down
menu, and click on “Warranty Registration”.
Business 8:00 AM to 5:00 PM
ours: Central Standard Time (C.S.T.)
(Summer ours: June to September –
8:00 AM to 5:00 PM C.S.T.
Monday through Thursday
8:00 AM to 2:30 PM C.S.T. Friday)
Telephone: (414) 671-6350
E-mail: part[email protected]
Fax: (414) 671-3976 (Parts and Service)
Additional information can be found by visiting our web site at
BBB3,?.:.:=;.:8.

Form No. IR1CEM-0910 3
#"$&!&%&*!"$ &"!
&$" !&!&$$! +$&34>@94?
2090=,?0>.7:>0=,920070.?=:8,290?4.1407/>?3,>-009
/0>4290/ ?: 800? ?30 ,;;74.,-70 >?,9/,=/> 1:= 9:9
49?0=10=09.0B4?3:?30=070.?=:94./0A4.0> ,60>@=0:?30=
070.?=:94./0A4.0>49?30A4.494?D 49.7@/492;,.08,60=>
,9/:?30= ,.?4A0 48;7,9?> 3,A0-009 /0>4290/?: 800?
?304=.:==0>;:9/492,;;74.,-70>?,9/,=/>
&34>@94?8@>?-0>0=A4.0/-D<@,74140/;0=>:9907:97D
%0=A4.0 -D @9<@,74140/ ;0=>:9907 8,D 70,/ ?: 070.?=4.
>3:.6:=-@=9
&34> @94? 3,> 9: K@>0=>0=A4.0,-70L ;,=?> 1 >0=A4.0 4>
=0<@4=0/:9?34>@94?.:9?,.?,9@?3:=4E0/,?.:%0=A4.0
209? := .:9?,.? ?30 ,?.: %0=A4.0 0;,=?809? ,?
1,C
'$!+$
I : 9:? 70,A0 80?,7 :-50.?> := @?09>47> :9 := 90,=
49/@.?4:9=,920&30D8,D-0.:803:?
I '>0 .,@?4:9 B309 B0,=492 =492> B,?.30> := :?30=
10==:@> :-50.?> ,=:@9/ 49/@.?4:9 =,920 &30D 8,D
-0.:803:?
I %:800C?0=4:=>@=1,.0>:9@94?B47720?3:?'>0.,@?4:9
B309?:@.3492?30>0,=0,>
:9:?-7:.6:==0>?=4.?,4=17:B?:,4=4970?147?0=:=0C3,@>?
1,9:9-:??:8:1@94?
:9:?>?:=0,9D?3492:9?:;:1@94?
:.,?0@94?,??30;=:;0=.:@9?0=30423?49,9,=0,?3,?4>
.:9A09409? 1:= @>0 &30 7:.,?4:9 >3:@7/ -0 70A07 ?:
;=0A09? ?30 @94? := 4?> .:9?09?> 1=:8 1,77492 ,..4/09?,77D
,9/>?=:9209:@23?:>@;;:=??30B0423?:1?30@94?,9/
.:9?09?>
!0A0=@>0,7@849@81:47:9?3049/@.?4:9=,9207@849@8
1:47B477807?,9//,8,20?30@94?
: 9:? ;7,.0 :-50.?> B4?3 8,290?4. ;=:;0=?40> .=0/4?
.,=/> .,>>0??0 ?,;0> 0?. :9 := 90,= @94? /@=492
:;0=,?4:9
'>0:97DB4;0>;,/>,9/.70,90=>/0>4290/>;0.414.,77D
1:=.70,9492.0=,84.27,>>>@=1,.0>
:9:?@>00C.0>>4A01:=.0B309?423?094928:@9?4929@?>
:9-@47?49@94?>&34>8,D/,8,20@94?,9/:=.:@9?0=?:;
'>09:9,-=,>4A0.70,90=>:97D-=,>4A0.70,90=>.:@7/
>.=,?.3?301494>3:1?30@94?8,==4924?>,;;0,=,9.0,9/
8,64924?>@>.0;?4-70?:>:47,..@8@7,?4:9
: 9:? >74/0 ;,9> ,.=:>> 27,>> >@=1,.0 @>0 =:@23
-:??:80/ ;,9> := /=:; ,9D?3492 :9 27,>> >@=1,.0
%.=,?.3492 := -=0,6,20 8,D :..@= ,8,20 ?: 27,>>
>@=1,.0 := -=0,6,20 :1 27,>> .,@>0/ -D 84>@>0 4> 9:?
.:A0=0/@9/0=B,==,9?D
NOTICE
CAUTION
WARNING
&$%"+$
I #7@2@94?49?:,;=:;0=7D2=:@9/0/070.?=4.,7=0.0;?,.70
:1?30.:==0.?A:7?,20>4E0,9/;7@2.:9142@=,?4:91
;7@2,9/=0.0;?,.70/:9:?8,?.3.:9?,.?,<@,74140/
070.?=4.4,9?:/0?0=8490,9/49>?,77?30;=:;0=A:7?,20
,9/>4E0070.?=4.,7=0.0;?,.70
I &@=9;:B0="@9;7@2;:B0=.:=/,9/,77:B@94??:
.::7-01:=0;0=1:=8492,9D8,49?09,9.0:=.70,9492
I "!"&>@-80=20:=>,?@=,?0B4?3B,?0='94?4>9:?
B,?0=;=::1:9:?:;0=,?041@94?3,>-009>@-80=20/
:=>,?@=,?0/B4?3B,?0=
I '94?4> 9:? B0,?30=;=::1:.,?0@94?49/::=>B30=0
,8-409?,4=?08;0=,?@=04>,84948@8:1HH
I :9:?>?0,8.70,9:=@>00C.0>>4A0B,?0=:9?30@94?
I &34>@94?4>9:?K50?;=::1L.:9>?=@.?4:9:9:?@>050?
.70,9>;=,D?:.70,9?34>@94?
I :9:?.70,9@94?B3094?4>090=24E0/:=3:?
I :9:?;@77@94?-D;:B0=.:=/
I 4>.:9?49@0@>041;:B0=.:=/4>1=,D0/:=B:=9
I :9:?,??08;??:=0;,4=:==0;7,.0,/,8,20/;:B0=
.:=/ &30 .:=/ 8@>? -0 =0;7,.0/ -D ,?.: ,9
@?3:=4E0/ ,?.: %0=A4.0 209? := , ;0=>:9 B4?3
>4847,=<@,7414.,?4:9>
I :9:?,77:B74<@4/>?:>;47749?:?30@94?
I '>0 :97D 09@490 ,?.: $0;7,.0809? #,=?> B309
>0=A4.0 4> =0<@4=0/ ,47@=0 ?: @>0 09@490 ,?.:
$0;7,.0809? #,=?> B477 A:4/ ,77 B,==,9?40> ,9/ 8,D
>@-50.? :;0=,?:=> :1 ?30 0<@4;809? ?: 3,E,=/:@>
070.?=4.,7A:7?,20=0>@7?49249070.?=4.,7>3:.6:=-@=9
09@490 ,?.: $0;7,.0809? #,=?> ,=0 >;0.4140/ ?:
:;0=,?0>,107D49?3009A4=:9809?>49B34.3?30D,=0
@>0/%:80,1?0=8,=60?:=2090=4.=0;7,.0809?;,=?>
/:9:?3,A0?30.3,=,.?0=4>?4.>?3,?B477,77:B?308?:
:;0=,?0>,107D49,?.:0<@4;809?
$+$
I :.,?0@94?,84948@8:188N1=:8.:8-@>?4-70
B,77> ,9/ 8,?0=4,7> 1 >,10 /4>?,9.0> ,=0 9:?
8,49?,490//4>.:7:=,?4:9:=.:8-@>?4:9.:@7/:..@=
I !0A0= :A0=7:,/ 0C?09>4:9 .:=/ '>0 30,AD /@?D
2=:@9/0/?3=00B4=00C?09>4:9.:=/:97D ,60>@=0
.@==09?.,==D492.,;,.4?D:10C?09>4:9.:=/.:8;740>
B4?3070.?=4.,7=,?492:1@94?
I :9:?;7,.0@94?90,=:=@9/0=90,?3.@=?,49>:=:?30=
.:8-@>?4-708,?0=4,7>?08>90,=:=,-:A0@94?.:@7/
.,?.314=0.,@>492495@=D,9/:=/,8,20?:@94?
:9:?30,?@9:;090/.:9?,490=>:11::/:9@94?%0,70/
30,?0/.:9?,490=>8,D-@=>?:;09
&34>@94?4>9:?49?09/0/1:=@>0-D.347/=09:=;0=>:9>
B4?3 =0/@.0/ ;3D>4.,7 >09>:=D := 809?,7 .,;,-474?40>
9>@=0;=:;0=>@;0=A4>4:9:1.347/=09,9/600;?308,B,D
1=:8?30@94?
,60>@=0,77:;0=,?:=>3,A0-00949>?=@.?0/:9?30>,10
,9/;=:;0=@>0:1?30@94?
WARNING
$0,/?301:77:B49248;:=?,9?>,10?D491:=8,?4:9-01:=0@>492?34>0<@4;809??:,A:4/>0=4:@>495@=D:=/0,?3,9/
?:,A:4//,8,20?:0<@4;809?:=;=:;0=?D

Form No. IR1CEM-0910
4
"%$#&"!
"%!&"!
77 :/07>
atco IR1 Series Induction Ranges are equipped with a single
induction coil underneath a ceramic glass surface. The
induction coil adapts to the induction-ready pan size to ensure
even heat distribution for even cooking. Each model features a
glass touch control panel with a Power On/Off button, eat
Setting controls, PRESET LEVELS buttons, and timer controls.
All Induction Ranges include an attached 1829 mm (72″) power
cord with plug.
NOTE: R f r to “Pan Sp cifications” in th OPERATION
s ction of this manual for d tails on “induction-r ady”
pans, pans not suitabl for induction cooking, and pan
siz s.
atco IR1 Series Induction Ranges have several safeguards
built in to each unit that ensure protection to the unit as well as
the operators.
• A dual fan ventilation system ensures that the electronic
circuits in the unit do no overheat. A temperature probe
monitors the electronic circuits and will signal the unit to
shut down if the circuits get too hot.
• A temperature probe in the cooking zone monitors the zone
temperature. This probe detects overheating in the cooking
zone due to an empty pan.
• A sensor in the cooking zone detects when a small, ferrous
object (such as a fork, spoon, or ring) is placed on the unit.
0” will flash on the eat Setting Display and the unit will
not operate.
:/07$
Model IR1-3000 Induction Range is a portable, countertop hob.
Figure 1. Model IR1-3000
:/07$
Model IRB1-3000 Induction Range is a built-in hob. Refer to the
INSTALLATION section of this manual for details on installing a
built-in hob.
Figure 2. Model IRB1-3000
:/07$)
Model IRW1-3000 induction range is a portable, countertop hob
designed specifically for use with a wok pan. The ceramic glass
surface as well as the induction coil underneath are shaped for
use with an induction-ready wok pan.
Figure 3. Model IRW1-3000
I R X 1 - XXXX
Induction Range Unit Wattage
No Character = Counter Top
B = Built-In
W = Wok
Single Coil
Figure 4. Model Designation

Form No. IR1CEM-0910 5
%#&"!%
:/07 (:7?,20 ),??> 8;> #7@2:9142@=,?4:9 %34;;492)0423?
IR1-3000 230 (CE) 3000 13.0 BS-1363 10 kg (21 lbs.)
IRB1-3000 230 (CE) 3000 13.0 BS-1363 11 kg (24 lbs.)
IRW1-3000 230 (CE) 3000 13.0 BS-1363 12 kg (27 lbs.)
70.?=4.,7$,?4923,=?
#7@2:9142@=,?4:9
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the application.
&$ %" +$ #7@2 @94? 49?: , ;=:;0=7D
2=:@9/0/070.?=4.,7=0.0;?,.70:1?30.:==0.?A:7?,20>4E0
,9/ ;7@2 .:9142@=,?4:9 1 ;7@2 ,9/ =0.0;?,.70 /: 9:?
8,?.3 .:9?,.? , <@,74140/ 070.?=4.4,9 ?: /0?0=8490 ,9/
49>?,77?30;=:;0=A:7?,20,9/>4E0070.?=4.,7=0.0;?,.70
NOTE: Th sp cification lab l is locat d on th bottom of th
unit. S lab l for s rial numb r and v rification of unit
l ctrical information.
WARNING
Figure 5. Plug Configuration
NOTE: R c ptacl not suppli d by Hatco.
BS-1363
NOTE: Shipping w ight includ s packaging.
4809>4:9>J :/07$
A
C
B
D
F
E
Front View
Side View
Top View
G
Figure 6. IR1-3000 Dimensions
)4/?3 0;?3 0423? ::?;=49? ::?;=49? ::?;=49? :47
:/07 )4/?3=:9? )4/?3$0,= 0;?3 4,80?0=
IR1-3000 392 mm 526 mm 91 mm 346 mm 356 mm 448 mm 295 mm
(15-7/16″) (20-3/4″) (3-5/8″) (13-5/8") (14") (17-5/8") (11-5/8")

Form No. IR1CEM-0910
6
%#&"!%
A
C
B
E
D
Front View
Side View
Top View
F
Figure 7. IRB1-3000 Dimensions
4809>4:9>J :/07$
)4/?3 0;?3 0423? @47?9 @47?9 :47
:/07 )4/?3 0;?3 4,80?0=
IRB1-3000 440 mm 580 mm 77 mm 369 mm 504 mm 295 mm
(17-3/8″) (22-7/8″) (3-1/16″) (14-9/16") (19-7/8") (11-5/8")
A
GC
B
F
D
E
Front View Side View
Figure 8. IRW1-3000 Dimensions
4809>4:9>J :/07$)
)4/?3 0;?3 0423? ::?;=49? ::?;=49? ::?;=49? ):6
:/07 )4/?3=:9? )4/?3$0,= 0;?3 $,/4@>
IRW1-3000 392 mm 526 mm 172 mm 346 mm 356 mm 448 mm 188 mm
(15-7/16″) (20-3/4″) (6-3/4″) (13-5/8") (14") (17-5/8") (7-3/8")

Form No. IR1CEM-0910 7
!%&&"!
090=,7
Induction Ranges are shipped completely assembled and
ready for use. Built-in units require installation into a countertop
(see procedure in this section). Care should be taken when
unpacking the shipping carton to avoid damage to the unit and
components enclosed.
&$ %" +$ '94? 4> 9:? B0,?30=;=::1
:.,?0@94?49/::=>B30=0,8-409?,4=?08;0=,?@=04>,
84948@8:1HH
$+$
I :.,?0@94?,84948@8:188N1=:8.:8-@>?4-70
B,77> ,9/ 8,?0=4,7> 1 >,10 /4>?,9.0> ,=0 9:?
8,49?,490//4>.:7:=,?4:9:=.:8-@>?4:9.:@7/:..@=
I :9:?;7,.0@94?90,=:=@9/0=90,?3.@=?,49>:=:?30=
.:8-@>?4-708,?0=4,7>?08>90,=:=,-:A0@94?.:@7/
.,?.314=0.,@>492495@=D,9/:=/,8,20?:@94?
:9:?-7:.6:==0>?=4.?,4=17:B?:,4=4970?147?0=:=0C3,@>?
1,9:9-:??:8:1@94?
1. Remove the unit from the carton.
2. Remove the information packet from the carton.
3. Remove tape and protective packaging from surfaces of unit.
NOTE: To pr v nt d lay in obtaining warranty cov rag ,
compl t onlin warranty r gistration. S
IMPORTANT OWNER INFORMATION for d tails.
4. Determine and prepare an appropriate installation location.
Make sure the installation location:
• is level and made of non-combustible material.
• is strong enough to support the unit and its contents.
• provides a minimum of 51 mm (2″) clearance from
combustible materials.
• is large enough for all four feet of the unit to be positioned
securely on the countertop (countertop units).
5. Install the unit on the countertop. For built-in units, refer to
the “Installing Built-In Models” procedure in this section.
9>?,77492@47?9 :/07>
IRB1-3000 models are built-in hobs that require installation into
a countertop before operation.
NOTE: Mak sur that th installation location allows acc ss to
th und rsid of th unit for maint nanc and cl aning
aft r it has b n plac d into th count rtop.
1. Carefully measure and cut
the appropriate opening in
the countertop. Refer to
the “Countertop Cutout
Dimensions” illustration.
NOTE: Mak sur a minimum
51 mm (2") cl aranc
will b availabl
b tw n th sid s of
th unit and any int rior
surfac . A minimum of
128 mm (5") will b
n d d b low th
count rtop surfac for
th h ight of th unit.
WARNING
CAUTION
400 mm
(15-3/4″)
540 mm
(21-1/4″)
Countertop
Cutout Dimensions
CountertopCountertop
CountertopCountertop
2. If necessary, make structural modifications or add bracing
underneath the countertop to ensure the countertop will
support the weight of the unit and its contents.
NOTE: Th count rtop must b l v l to nsur prop r
op ration of th Induction Rang .
3. Make sure the cabinetry provides proper ventilation with
external air to the underside of the unit. If necessary, cut
ventilation openings in the cabinetry to provide the
ventilation. Louvered or grill-style panels should be
installed in the openings.
4. Make sure a grounded electrical receptacle of the correct
voltage, size, and plug configuration is within 1829 mm
(72″) inside the mounting location for the unit. See the
SPECIFICATIONS section for details.
5. Apply a bead of silicone sealant onto the countertop
material around the cutout opening.
6. Carefully lower the unit into the opening, making sure the
power cord does not get pinched.
7. Assemble mounting clips and mounting nuts to the eight
mounting studs on the underside of the unit.
NOTE: Mounting clips and mounting nuts not suppli d—
provid d by install r.
Figure 9. Installing the Unit into the Countertop
8. Tighten and readjust the mounting nuts on the mounting
clips until the flange lies flat on the countertop.
:9:?@>00C.0>>4A01:=.0B309?423?094928:@9?4929@?>
:9-@47?49@94?>&34>8,D/,8,20@94?,9/:=.:@9?0=?:;
9. Provide separation underneath the unit between the cooling
air inlet filter and the exhaust fan. This is necessary to prevent
hot exhaust air from being drawn back into the unit through
the cooling air inlet, which could cause the unit to overheat.
Figure 10. Inlet and Exhaust Air Separation
10. Plug the power cord on the unit into the electrical
receptacle.
Mounting Nut
Mounting Stud
(M4 Thread)
Apply a bead of silicone sealant
between the countertop material
and the flange on the unit.
Flange (Front View)
Mounting Clip
Countertop
Material
NOTICE
Grill Panel
(Min. 150 cm² [60 in²])
Exhaust
Fan Front of unit. Air Inlet
Filter
Separation
(non-combustible
material)

Form No. IR1CEM-0910
8
"#$&"!
090=,7
The general operation for IR1, IRB1, and IRW1 Series Induction
Ranges is the same. Use the following information and
procedures to operate a atco Induction Range. NOTICE:
9:?8:A0@94?/@=492:;0=,?4:9
$0,/ ,77 >,10?D 80>>,20> 49 ?30 #"$&!& %&*
!"$ &"! >0.?4:9-01:=0:;0=,?492?34>0<@4;809?
#,9%;0.414.,?4:9>
Pans used with an Induction Range must meet the following
specifications:
• Made of material with magnetic properties (ferrous
material)
- Enamelled Steel Pans
- Cast Iron Pans
- Stainless Steel Pans
- Aluminum Pans w/ferrous base
• Proper size (measurements given are the manufacturer’s
pan size, not the pan bottom diameter)
- IR1 and IRB1 Series = Min. 152 mm (6″) to
Max. 356 mm (14″)
- IRW1 Series = Min. 279 mm (11″) to Max. 356 mm (14″)
NOTE: Pan bottoms should not xt nd mor than 13 mm (1/2″)
b yond th cooking zon patt rns on th glass surfac .
• Flat bottom (except for Model IRW1)
The following pans .,99:? be used with an Induction Range:
• Glass Pans
• Aluminum Pans w/o ferrous base
• Earthenware Pans
• Ceramic Pans
• Copper Pans
NOTE: Th Induction Rang automatically d t cts if a pan is
induction-r ady. If a pan is plac d on th unit that is not
induction-r ady, “0” will flash on th H at S tting
Display and th unit will not op rat .
%?,=?@;
1. Before turning on the unit each day, clean the glass surface
using an appropriate cleaning wipe, damp paper towel, or
a damp cloth. '&"!)4;0@;,77>;477>,9/>;7,>30>
4880/4,?07D ,60>@=0@94?4>/=D-01:=0@>492:
9:?,77:B74<@4/?:=@949?:,4=4970?147?0=:9-:??:8:1
@94?
WARNING
2. For countertop units, plug the unit into a properly grounded
electrical receptacle of the correct voltage, size, and plug
configuration. See the SPECIFICATIONS section for
details.
3. Place an induction-ready pan on the unit. The Induction
Range will not operate without a pan centered inside the
cooking zone pattern on the glass surface.
• The induction coils underneath the glass surface will
adjust automatically to the pan size to provide even heat
distribution.
4. Touch the Button (Power On/Off) to turn on the
Induction Range.
• “0” is shown flashing on the eat Setting Display.
5. Select the desired heat setting. eat settings can be
selected in one of two ways:
• Touch the or eat Setting Button to select the
desired heat setting from 1 to 12.
• Touch one of the PRESET LEVELS Buttons.
Button = eat setting 6 (medium heat)
Button = eat setting 10 (high heat)
Button = eat setting 12 (maximum heat)
'$!+$
I :9:?70,A080?,7:-50.?>:=@?09>47>:9:=90,=?30
49/@.?4:9=,920&30D8,D-0.:803:?
I '>0 .,@?4:9 B309 B0,=492 =492> B,?.30> := :?30=
10==:@> :-50.?> ,=:@9/ 49/@.?4:9 =,920 &30D 8,D
-0.:803:?
I %:800C?0=4:= >@=1,.0> :9?30 @94?B477 20?3:? '>0
.,@?4:9B309?:@.3492?30>0,=0,>
6. If cooking with the timer, touch the or Timer Button
to select the cooking time from 1 to 99 minutes. The timer
setting can be changed at any time while the unit is on.
When the timer reaches “0” an intermittent alarm will sound,
and the Induction Range will shut off. Press any button to
stop the alarm.
%3@?/:B9
1. Touch the Button to turn off the Induction Range.
NOTE: H at g n ration will stop automatically wh n v r a pan
is r mov d from th glass surfac . Th curr nt s tting
will flash until th pan is r plac d and h at g n ration
r sum s.
CAUTION
PRESET LEVELS
Buttons Timer
Buttons and Display
Power On/Off
Button
Heat Setting
Buttons and Display
Figure 11. IR1 Series Control Panel

Form No. IR1CEM-0910 9
!&!!
090=,7
atco Induction Ranges are designed for maximum durability
and performance with minimum maintenance.
&$%"+$
I &@=9;:B0="@9;7@2;:B0=.:=/,9/,77:B@94??:
.::7-01:=0;0=1:=8492,9D8,49?09,9.0:=.70,9492
I "!"&>@-80=20:=>,?@=,?0B4?3B,?0='94?4>9:?
B,?0=;=::1:9:?:;0=,?041@94?3,>-009>@-80=20/
:=>,?@=,?0/B4?3B,?0=
I :9:?>?0,8.70,9:=@>00C.0>>4A0B,?0=:9?30@94?
I &34>@94?4>9:?K50?;=::1L.:9>?=@.?4:9:9:?@>050?
.70,9>;=,D?:.70,9?34>@94?
I :9:?.70,9@94?B3094?4>090=24E0/:=3:?
&34> @94? 3,> 9: K@>0=>0=A4.0,-70L ;,=?> 1 >0=A4.0 4>
=0<@4=0/:9?34>@94?.:9?,.?,9@?3:=4E0/,?.:%0=A4.0
209? := .:9?,.? ?30 ,?.: %0=A4.0 0;,=?809? ,?
1,C
)4;0@;,77>;477>,9/>;7,>30>4880/4,?07D ,60>@=0@94?
4>/=D-01:=0@>492:9:?,77:B74<@4/?:=@949?:,4=4970?
147?0=:9-:??:8:1@94?
,47D70,9492
To maintain performance and preserve the finish of the
Induction Range, clean the unit daily. Make sure to use only
wipes, pads, and cleaners designed specifically for cleaning
ceramic glass surfaces.
1. Turn off the unit and allow to cool.
2. Remove and wash all food pans.
3. Clean the glass surface using an appropriate cleaning
wipe, damp paper towel, or damp cloth.
• For tough stains and metal marks, use a drop of ceramic
glass cleaner and paper towel.
• For water and scale marks, use a few drops of white
vinegar and paper towel.
'>09:9,-=,>4A0.70,90=>:97D-=,>4A0.70,90=>.:@7/
>.=,?.3?301494>3:1?30@94?8,==4924?>,;;0,=,9.0,9/
8,64924?>@>.0;?4-70?:>:47,..@8@7,?4:9
4. Clean the metal surfaces using a clean, soft cloth and mild
detergent.
WARNING
CAUTION
NOTICE
70,9492?304=970?47?0=
The air inlet filter on the bottom of the unit should be removed
and cleaned monthly. Use the following procedure to clean the
filter.
1. Turn off and unplug the unit .Allow the unit to cool.
2. Access the air inlet filter.
• For counter top units, turn the unit upside down and lay
the unit on a soft, non-scratching surface.
• For built-in units, access the bottom of the unit.
3. Remove the frame screw on the filter frame.
4. Lift the filter frame and air inlet filter off of the unit.
5. Clean the air inlet filter with soapy water.
6. Allow the air inlet filter to dry completely.
7. Place the air inlet filter inside the filter frame and install onto
the bottom of the unit.
• Insert the tabs on the filter frame into the tab slots on the
bottom of the unit.
8. Insert the frame screw and tighten securely.
9. For countertop units, return the unit to the upright position.
Figure 12. Removing the Air Inlet Filter (Model IR1-3000 shown)
Frame
Screw
Air Inlet
Filter
Tab
Filter Frame
Tab Slot

%D8;?:8 #=:-,-70,@>0 :==0.?4A0.?4:9
Unit does not turn on. No power to unit. Make sure power cord is plugged into an appropriate
receptacle (see SPECIFICATIONS section). Check
circuit breaker and reset as necessary. Check for
damage to power cord. Check electrical receptacle.
Electronic controls defective. Contact Authorized Service Agent or atco for assistance.
“0” flashes in on eat Setting
Display and the unit will not
heat.
Pan being used is not induction-
ready.
Use an induction-ready pan (see “Pan Specifications” in
the OPERATION section of this manual).
Unit stops working during
operation (error code “F7” may
appear on eat Setting Display).
Electronic controls have
overheated.
Make sure installation location allows proper ventilation
underneath the unit:
• Make sure air inlet filter and exhaust fan are not
blocked.
• Make sure air inlet filter is clean.
• Make sure installation of built-in unit provides proper
separation between cooling air (air inlet) and hot
exhaust air (exhaust fan).
Exhaust fan continues to run
and “ ” appears on eat Setting
Display after unit has been
turned off.
Cooling of the electronic controls
not complete.
No action necessary. This is a normal function of the unit.
Exhaust fan starts for a few
seconds after plugging in unit.
Automatic testing of unit. No action necessary. This is a normal function of the unit.
Form No. IR1CEM-0910
10
&$"'%""&!'
&34>@94?8@>?-0>0=A4.0/-D<@,74140/;0=>:9907:97D
%0=A4.0 -D @9<@,74140/ ;0=>:9907 8,D 70,/ ?: 070.?=4.
>3:.6:=-@=9
WARNING
&$ %" +$ &@=9 ;:B0= >B4?.3 "
@9;7@2 ;:B0= .:=/ ,9/ ,77:B @94? ?: .::7 -01:=0
;0=1:=8492,9D8,49?09,9.0:=.70,9492
WARNING

Form No. IR1CEM-0910 11
&)$$!&*
%$(!"$ &"!
),==,9?D>>@0>J '94?0/492/:8
The warranty on atco Induction Ranges is for one year from
date of purchase or eighteen months from date of shipping from
atco, whichever occurs first.
If you experience an issue with an Induction Range during the
warranty period, contact the ,==09=:@; at:
&070;3:90
When contacting the Marren Group for warranty assistance,
please supply the following information:
• Model of unit
• Serial number (located on the bottom of the unit)
• Specific problem with the unit
• Date of purchase
• Name of business
• Shipping address
• Contact name and telephone number
!:9),==,9?D>>@0>
If you experience a non-warranty issue that requires assistance,
please contact the Marren Group.
#$"'&)$$!&*
atco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with atco’s written instructions or
18 months from the date of shipment from atco. Buyer must
establish the Product’s purchase date by returning atco’s
Warranty Registration Card or by other means satisfactory to
atco in its sole discretion.
atco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
, "90*0,=#,=?>,9/,-:=#'%"90
//4?4:9,7*0,=#,=?>"97D),==,9?D
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Food Warmer Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
olding Cabinet Elements (metal sheathed air heating)
Built-In eated Well Elements — WB and WBI Series
(metal sheathed)
- "90*0,=#,=?>,9/,-:=#'%:@=
*0,=>#,=?>"97D),==,9?D:9
;=:=,?0/?0=8>?3,?,?.:B4770C;7,49
,?@D0=M>=0<@0>?
3CS and FR Tanks
. "90*0,=#,=?>,9/,-:=#'%!490
*0,=>#,=?>"97D),==,9?D:9
Electric Booster eater Tanks
Gas Booster eater Tanks
/ !490?D,D#,=?>"97D),==,9?D
Replacement Parts
T E FOREGOING WARRANTIES ARE EXCLUSIVE AND IN
LIEU OF ANY OT ER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERC ANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR PATENT OR OT ER
INTELLECTUAL PROPERTY RIG T INFRINGEMENT.
Without limiting the generality of the foregoing, SUC
WARRANTIES DO NOT COVER: Coated incandescent light
bulbs, fluorescent lights, heat lamp bulbs, coated halogen light
bulbs, halogen heat lamp bulbs, glass components, and fuses;
Product failure in booster tank, fin tube heat exchanger, or other
water heating equipment caused by liming, sediment buildup,
chemical attack, or freezing; or Product misuse, tampering or
misapplication, improper installation, or application of improper
voltage.
&&"!"$ %! %
atco’s liability and Buyer’s exclusive remedy hereunder will be
limited solely, at atco’s option, to repair or replacement using
new or refurbished parts or Product by atco or a atco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case atco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. atco reserves
the right to accept or reject any such claim in whole or in part.
In the context of this Limited Warranty, “refurbished” means a
part or Product that has been returned to its original
specifications by atco or a atco-authorized service agency.
atco will not accept the return of any Product without prior
written approval from atco, and all such approved returns shall
be made at Buyer’s sole expense. ATCO WILL NOT BE
LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM T E USE OF OR INABILITY TO USE T E
PRODUCTS OR FROM T E PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OT ER PRODUCT OR GOODS.

12 P/N 07.04.551.00 Form No. IR1CEM-0910
Printed in U.S.A. September 2010
HATCO CORPORATION
P.O. Box 340500
Milwaukee, WI 53234-0500 U.S.A.
Telephone (414) 671-6350
International Fax (414) 671-3976
www.hatcocorp.com
&"'&"$+#$&%%&$'&"$%
'94?0/492/:8
Marren Group
Northants +44(0)1933 666233
$024>?0=D:@=@94?:97490
See IMPORTANT OWNER INFORMATION
section for details.
Other manuals for IR1-3000
1
This manual suits for next models
2
Table of contents
Other Hatco Range manuals
Popular Range manuals by other brands

FiveStar
FiveStar TPN310-7 Use and care and installation instructions

GE
GE CGS975SEDSS Dimensions and installation information

KitchenAid
KitchenAid KESC300 Use and care guide

Kenmore
Kenmore 911.92391 owner's manual

Kenmore
Kenmore 9742 - 30 in. Electric Range Use and care guide

GE
GE JSS28DN Dimensions and installation information