Hatco HDW Series User manual

hatcocorp.com
Register Online!
(see page 2)
P/N 07.04.838.00 © 2017 Hatco Corporation
Drawer Warmers
抽屉式保温柜
HDW Series/系列
Installation and Operating Manual
安装及操作手册
Do not operate this equipment unless you have read
and understood the contents of this manual! Failure
to follow the instructions contained in this manual
may result in serious injury or death. This manual
contains important safety information concerning
the maintenance, use, and operation of this product.
If you’re unable to understand the contents of this
manual, please bring it to the attention of your
supervisor. Keep this manual in a safe location for
future reference.
English = p 2
WARNING
请在认真阅读并理解本手册的内容后再操作本设
备！不按照本手册中的说明操作可能会导致严重
的人身伤亡事故。本手册中包含了有关本产品维
护、使用和操作的重要安全事项。如果您不理解
本手册的内容，请将本手册交给主管人员，以提
请其注意。请将本手册妥善放置，以便参照。
中文 = 第 18 页

Form No. HDWM_CN-0817
2
English
CONTENTS
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to personal
injury.
INTRODUCTION
Hatco Drawer Warmers are designed to keep foods at optimum
serving temperatures without affecting quality. They are built
for tough kitchen duty with rugged stainless steel construction,
heavy-duty hardware, stainless steel slides, and positive-
closing drawers. Drawer Warmers keep everything from meat
to vegetables to rolls hot and flavor-fresh until served.
On multiple drawer units, each drawer features individual
controls for holding a wider variety of hot foods during peak
serving periods.
Hatco Drawer Warmers are products of extensive research and
field testing. The materials used were selected for maximum
durability, attractive appearance, and optimum performance.
Every unit is inspected and tested thoroughly prior to shipment.
This manual provides the installation, safety, and operating
instructions for Drawer Warmers. Hatco recommends all
installation, operating, and safety instructions appearing in this
manual be read prior to installation or operation of the unit.
Important Owner Information..............................................2
Introduction...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Chart.........................................................5
Food Holding Capacity ........................................................7
Dimensions..........................................................................8
Installation...........................................................................10
General.............................................................................. 10
Installing HDW-x and HDW-xN Models .............................10
Installing HDW-xB, HDW-xBN, and HDW-xBR Models..... 11
Operation.............................................................................12
General.............................................................................. 12
Maintenance........................................................................13
General.............................................................................. 13
Daily Cleaning ...................................................................13
Removing Lime and Mineral Deposits ..............................13
Troubleshooting Guide ......................................................14
Options and Accessories ..................................................15
International Limited Warranty .........................................17
Service Information............................................................17
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and
purchase date of the unit in the spaces below (located on the
back of the unit for free-standing units and on the inside of
the right panel for built-in units). Please have this information
available when calling Hatco for service assistance.
Model No. ____________________________________
Serial No._____________________________________
Voltage_______________________________________
Date of Purchase_______________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Parts & Service pull-down
menu, and click on “Warranty Registration”.
Business 9:00 AM to 6:00 PM (Beijing Time)
Hours: Monday through Friday
Telephone: [phone]
E-mail: [email protected]
Additional information can be found by visiting our web site at
www.hatcocorp.com

Form No. HDWM_CN-0817 3
English IMPORTANT SAFETY INFORMATION
WARNING
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Hatco Corporation is not responsible for actual food
product serving temperature. It is the responsibility of the
user to ensure that food product is held and served at a
safe temperature.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them away
from the unit.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact Hatco at [phone].
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Use caution when opening drawer. Hot air escapes
when drawer is open.
Locate unit in an area that is convenient for use. The
location should be level and strong enough to support the
weight of the unit and contents.
NOTICE
Do not lay unit on the front or back side. Damage to the
unit could occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Built-in units must be installed by a qualified electrician.
Installation must conform to all local electrical codes.
Installation by unqualified personnel will void unit
warranty and may lead to electric shock or burn, as
well as damage to unit and/or its surroundings.
• Turn OFF power switch, unplug power cord/turn off
power at circuit breaker, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 21°C (70°F).
• Do not clean unit when it is energized or hot.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Do not allow liquids to spill into unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD:
 • Locateunitaminimumof25mm(1″)fromcombustible
walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
• Do not use harsh chemicals such as bleach (or cleaners
containing bleach), oven cleaners, or flammable
cleaning solutions to clean this unit.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.

Form No. HDWM_CN-0817
4
English
MODEL DESCRIPTION
All Models
All Hatco Drawer Warmers are built of rugged aluminized and
stainless steel with durable nylon rollers, 12 gauge stainless
steel slides, and heavy-duty hardware. Each drawer features
adjustable drawer vents for humidity control, a POWER I/O (on/
off) switch, Temperature control knob, and a TEMPERATURE
monitor. Standard size pans 152 mm (6″) deep are supplied with
each drawer. The insulated top and sides provide maximum
energy efficiency and the heating elements are warranted for
two years.
HDW-x Models
HDW-x Models are freestanding units available in one, two,
three, and four-drawer versions. The one, two, and three-
drawer units are equipped with 102 mm (4″) legs. The
four-drawer unit is equipped with 152 mm (6″) stainless steel
legs. Freestanding models include an attached 1829 mm (6′)
power cord with plug.
HDW-xN Models
HDW-xN models have all the features of the HDW-x
freestanding models but have a narrower profile for smaller
space requirements. These units are available in one, two, and
three-drawer versions.
Drawer
Vents
Power I/O (on/off) Switch
Temperature Monitor
TEMPERATURE Control Knob
Model HDW-2
NOTE: Additional caster and leg sizes are available for
the freestanding units. Refer to the OPTIONS AND
ACCESSORIES section for details.
HDW-xB Models
HDW-xB Models are built-in units available in one, two, and
three-drawer versions. Built-in HDW-xB models include
1219 mm (4′) of flexible conduit for direct power connection.
HDW-xBN Models
HDW-xBN Models have all the features of the HDW-xB models
but have a narrower profile for smaller space requirements.
These units are available in one, two, and three-drawer
versions.
Drawer
Vents
Temperature Monitor
Power I/O (on/off) Switch
TEMPERATURE Control Knob
Model HDW-2B
HDW-xBR Models
HDW-xBR Models have all the features of the HDW-xB models
but have a reduced depth for smaller space requirements.
These units are available in one, two, and three-drawer
versions.
MODEL DESIGNATION
H D W - x x
Heated No Character = Freestanding
N = Freestanding, Narrow
B = Built-In
BN = Built-In, Narrow
BR = Built-In, Reduced Depth
Drawer Warmer
Quantity of Drawers

Form No. HDWM_CN-0817 5
English SPECIFICATIONS
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug. Plugs are supplied according to the application.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification label is located on the bottom of the
unit. See label for serial number and verification of unit
electrical information.
CEE 7/7 Schuko BS-1363
JIS C 8303
15 A, 125 V
Plug Configurations
NOTE: Receptacle not supplied by Hatco.
Electrical Rating Chart — HDW-x Models
NOTE: Shipping weight includes packaging.
Model Voltage Watts Amps PlugConguration Shipping Weight
HDW-1 100 450 4.5 JIS C 8303 15 A, 125 V 44 kg (97 lbs.)
220 450 2.0 CEE 7/7 Schuko 44 kg (97 lbs.)
240 450 1.9 BS-1363 44 kg (97 lbs.)
220–230 450–492 2.0–2.1 CEE 7/7 Schuko 44 kg (97 lbs.)
230–240 413–450 1.8–1.9 BS-1363 44 kg (97 lbs.)
HDW-2 100 900 9.0 JIS C 8303 15 A, 125 V 76 kg (168 lbs.)
220 900 4.1 CEE 7/7 Schuko 76 kg (168 lbs.)
240 900 3.8 BS-1363 76 kg (168 lbs.)
220–230 900–984 4.1–4.3 CEE 7/7 Schuko 76 kg (168 lbs.)
230–240 826–900 3.6–3.8 BS-1363 76 kg (168 lbs.)
HDW-3 100 1350 13.5 JIS C 8303 15 A, 125 V 105 kg (232 lbs.)
220 1350 6.1 CEE 7/7 Schuko 105 kg (232 lbs.)
240 1350 5.6 BS-1363 105 kg (232 lbs.)
220–230 1350–1476 6.1–6.4 CEE 7/7 Schuko 105 kg (232 lbs.)
230–240 1239–1350 5.4–5.6 BS-1363 105 kg (232 lbs.)
HDW-4 220 1800 8.2 CEE 7/7 Schuko 135 kg (296 lbs.)
240 1800 7.5 BS-1363 135 kg (296 lbs.)
220–230 1800–1968 8.2–8.6 CEE 7/7 Schuko 135 kg (296 lbs.)
230–240 1653–1800 7.2–7.5 BS-1363 135 kg (296 lbs.)

Form No. HDWM_CN-0817
6
English
SPECIFICATIONS
Electrical Rating Chart — HDW-xN Models
Model Voltage Watts Amps PlugConguration Shipping Weight
HDW-1N 100 450 4.5 JIS C 8303 15 A, 125 V 38 kg (83 lbs.)
220 450 2.0 CEE 7/7 Schuko 38 kg (83 lbs.)
240 450 1.9 BS-1363 38 kg (83 lbs.)
220–230 450–492 2.0–2.1 CEE 7/7 Schuko 38 kg (83 lbs.)
230–240 413–450 1.8–1.9 BS-1363 38 kg (83 lbs.)
HDW-2N 100 900 9.0 JIS C 8303 15 A, 125 V 76 kg (168 lbs.)
220 900 4.1 CEE 7/7 Schuko 76 kg (168 lbs.)
240 900 3.8 BS-1363 76 kg (168 lbs.)
220–230 900–984 4.1–4.3 CEE 7/7 Schuko 76 kg (168 lbs.)
230–240 826–900 3.6–3.8 BS-1363 76 kg (168 lbs.)
HDW-3N 100 1350 13.5 JIS C 8303 15 A, 125 V 105 kg (232 lbs.)
220 1350 6.1 CEE 7/7 Schuko 105 kg (232 lbs.)
240 1350 5.6 BS-1363 105 kg (232 lbs.)
220–230 1350–1476 6.1–6.4 CEE 7/7 Schuko 105 kg (232 lbs.)
230–240 1239–1350 5.4–5.6 BS-1363 105 kg (232 lbs.)
Electrical Rating Chart — HDW-xB Models
Model Voltage Watts Amps PlugConguration Shipping Weight
HDW-1B 220 450 2.0 Hardwired w/ Conduit 40 kg (88 lbs.)
240 450 1.9 Hardwired w/ Conduit 40 kg (88 lbs.)
220–230 450–492 2.0–2.1 Hardwired w/ Conduit 40 kg (88 lbs.)
230–240 413–450 1.8–1.9 Hardwired w/ Conduit 40 kg (88 lbs.)
HDW-2B 220 900 4.1 Hardwired w/ Conduit 72 kg (159 lbs.)
240 900 3.8 Hardwired w/ Conduit 72 kg (159 lbs.)
220–230 900–984 4.1–4.3 Hardwired w/ Conduit 72 kg (159 lbs.)
230–240 826–900 3.6–3.8 Hardwired w/ Conduit 72 kg (159 lbs.)
HDW-3B 220 1350 6.1 Hardwired w/ Conduit 105 kg (232 lbs.)
240 1350 5.6 Hardwired w/ Conduit 105 kg (232 lbs.)
220–230 1350–1476 6.1–6.4 Hardwired w/ Conduit 105 kg (232 lbs.)
230–240 1239–1350 5.4–5.6 Hardwired w/ Conduit 105 kg (232 lbs.)
NOTE: Shipping weight includes packaging.
NOTE: Shipping weight includes packaging.

Form No. HDWM_CN-0817 7
English SPECIFICATIONS
Electrical Rating Chart — HDW-xBN Models
Model Voltage Watts Amps PlugConguration Shipping Weight
HDW-1BN 220 450 2.0 Hardwired w/ Conduit 40 kg (88 lbs.)
240 450 1.9 Hardwired w/ Conduit 40 kg (88 lbs.)
220–230 450–492 2.0–2.1 Hardwired w/ Conduit 40 kg (88 lbs.)
230–240 413–450 1.8–1.9 Hardwired w/ Conduit 40 kg (88 lbs.)
HDW-2BN 220 900 4.1 Hardwired w/ Conduit 72 kg (159 lbs.)
240 900 3.8 Hardwired w/ Conduit 72 kg (159 lbs.)
220–230 900–984 4.1–4.3 Hardwired w/ Conduit 72 kg (159 lbs.)
230–240 826–900 3.6–3.8 Hardwired w/ Conduit 72 kg (159 lbs.)
HDW-3BN 220 1350 6.1 Hardwired w/ Conduit 105 kg (232 lbs.)
240 1350 5.6 Hardwired w/ Conduit 105 kg (232 lbs.)
220–230 1350–1476 6.1–6.4 Hardwired w/ Conduit 105 kg (232 lbs.)
230–240 1239–1350 5.4–5.6 Hardwired w/ Conduit 105 kg (232 lbs.)
Electrical Rating Chart — HDW-xBR Models
Model Voltage Watts Amps PlugConguration Shipping Weight
HDW-1BR 220 450 2.0 CEE 7/7 Schuko 36 kg (80 lbs.)
240 450 1.9 BS-1363 36 kg (80 lbs.)
220–230 450–492 2.0–2.1 CEE 7/7 Schuko 36 kg (80 lbs.)
230–240 413–450 1.8–1.9 BS-1363 36 kg (80 lbs.)
HDW-2BR 220 900 4.1 CEE 7/7 Schuko 76 kg (168 lbs.)
240 900 3.8 BS-1363 76 kg (168 lbs.)
220–230 900–984 4.1–4.3 CEE 7/7 Schuko 76 kg (168 lbs.)
230–240 826–900 3.6–3.8 BS-1363 76 kg (168 lbs.)
HDW-3BR 220 1350 6.1 CEE 7/7 Schuko 105 kg (232 lbs.)
240 1350 5.6 BS-1363 105 kg (232 lbs.)
220–230 1350–1476 6.1–6.4 CEE 7/7 Schuko 105 kg (232 lbs.)
230–240 1239–1350 5.4–5.6 BS-1363 105 kg (232 lbs.)
Food Holding Capacity
A standard drawer has the following capacity:
Dinner Rolls: 6–8 dozen
Ribs: 11–14 kg (25–30 lbs.)
Potatoes: 3–3-1/2 dozen
NOTE: Shipping weight includes packaging.
NOTE: Shipping weight includes packaging.

Form No. HDWM_CN-0817
8
English
Dimensions — HDW-x and HDW-xN Models
A B
D E
C
Front View Side View
Model
Width
(A)
Depth
(B) †
Height
(C) *
Footprint
Width (D)
Footprint
Depth (E)
HDW-1 749 mm
(29-1/2″)
575 mm
(22-5/8″)
381 mm
(15-1/16″)
629 mm
(24-3/4″)
484 mm
(19-1/16″)
HDW-2 749 mm
(29-1/2″)
575 mm
(22-5/8″)
639 mm
(25-3/16″)
629 mm
(24-3/4″)
484 mm
(19-1/16″)
HDW-3 749 mm
(29-1/2″)
575 mm
(22-5/8″)
896 mm
(35-1/4″)
629 mm
(24-3/4″)
484 mm
(19-1/16″)
HDW-4 749 mm
(29-1/2″)
575 mm
(22-5/8″)
1203 mm
(47-3/8″)
629 mm
(24-3/4″)
484 mm
(19-1/16″)
HDW-1N 530 mm
(20-7/8″)
686 mm
(27″)
381 mm
(15-1/16″)
408 mm
(16-1/8″)
594 mm
(23-7/16″)
HDW-2N 530 mm
(20-7/8″)
686 mm
(27″)
639 mm
(25-3/16″)
408 mm
(16-1/8″)
594 mm
(23-7/16″)
HDW-3N 530 mm
(20-7/8″)
686 mm
(27″)
896 mm
(35-1/4″)
408 mm
(16-1/8″)
594 mm
(23-7/16″)
Dimensions — HDW-xB and HDW-xBN Models
Model
Width
(A)
Depth
(B) †
Height
(C)
Built-In
Width (D)
Built-In
Height (E)
HDW-1B 743 mm
(29-1/4″)
568 mm
(22-3/8″)
276 mm
(10-7/8″)
715 mm
(28-3/16″)
248 mm
(9-13/16″)
HDW-2B 743 mm
(29-1/4″)
568 mm
(22-3/8″)
534 mm
(21″)
715 mm
(28-3/16″)
506 mm
(19-15/16″)
HDW-3B 743 mm
(29-1/4″)
568 mm
(22-3/8″)
791 mm
(31-1/8″)
715 mm
(28-3/16″)
763 mm
(30″)
HDW-1BN 523 mm
(20-9/16″)
680 mm
(26-3/4″)
276 mm
(10-7/8″)
494 mm
(19-1/2″)
248 mm
(9-13/16″)
HDW-2BN 523 mm
(20-9/16″)
680 mm
(26-3/4″)
534 mm
(21″)
494 mm
(19-1/2″)
506 mm
(19-15/16″)
HDW-3BN 523 mm
(20-9/16″)
680 mm
(26-3/4″)
791 mm
(31-1/8″)
494 mm
(19-1/2″)
763 mm
(30″)
* Height (C) includes 102 mm (4″) legs for 1–3 drawer models and 152 mm (6″) legs for 4 drawer models.
Refer to the OPTIONS AND ACCESSORIES section for Height (C) with optional casters.
†Add 70 mm (2-3/4″) to Depth (B) to include the drawer handle and power cord/conduit connector.
AB
C
D
E
Front View Side View
SPECIFICATIONS

Form No. HDWM_CN-0817 9
English
Dimensions — HDW-xBR
Model
Width
(A)
Depth
(B) †
Height
(C)
Built-In
Width (D)
Built-In
Height (E)
HDW-1BR 740 mm
(29-1/8″)
418 mm
(16-1/2″)
273 mm
(10-3/4″)
715 mm
(28-3/16″)
248 mm
(9-3/4″)
HDW-2BR 740 mm
(29-1/8″)
418 mm
(16-1/2″)
546 mm
(21-1/2″)
715 mm
(28-3/16″)
521 mm
(20-1/2″)
HDW-3BR 740 mm
(29-1/8″)
418 mm
(16-1/2″)
819 mm
(32-1/4″)
715 mm
(28-3/16″)
794 mm
(31-1/4″)
†Add 70 mm (2-3/4″) to Depth (B) to include the drawer handle and power cord/conduit connector.
AB
C
D
E
Front View Side View
SPECIFICATIONS

Form No. HDWM_CN-0817
10
English
INSTALLATION
General
Hatco Drawer Warmers are shipped with most components
pre-assembled. Care should be taken when unpacking the
shipping carton to avoid damage to the unit and components
enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 21°C (70°F).
FIRE HAZARD:Locateunitaminimumof25mm(1″)from
combustible walls and materials. If safe distances are not
maintained, combustion or discoloration could occur.
NOTICE
Do not lay unit on the front or back side. Damage to the
unit could occur.
1. Remove the unit from the carton. Two people are required
for this step.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of the unit
3. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 21° C
(70° F). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure all the feet on the bottom of the unit are
positioned securely on the countertop.
4. Install the unit. Refer to the appropriate installation
procedure in this section.
Installing HDW-x and HDW-xN Models
HDW-x and HDW-xN models are freestanding units that require
the installation of legs or casters before operation.
1. Remove the plastic bag containing the four legs or casters
from the drawer of the unit.
2. Carefully lay the unit on its side (requires two people).
3. Install each leg or caster. Refer to the appropriate
procedure in this section.
4. Return the unit to its upright position (requires two people).
For units on legs — If the unit is not level or rocks, turn the
adjustable tip of the appropriate leg to level the unit.
Installing Legs
1. Thread a leg into the hole located at one corner of the unit.
2. Hand-tighten the leg until snug. Do not over-tighten.
3. Repeat steps 1 and 2 for the remaining three legs.
Lengthen
Shorten
Adjustable
Tip
Leg Installation on HDW-2 Model
Installing Casters
1. Align the four holes on the caster plate with the four holes
in the bottom of the unit at one corner of the unit.
2. Install a bolt through each of the holes in the caster plate
and into the bottom of the unit. Tighten securely.
3. Repeat steps 1 and 2 for the remaining three casters.
Caste
r
Plate
Bolt
Caster Installation on HDW-3 Model

Form No. HDWM_CN-0817 11
English
Installing HDW-xB, HDW-xBN, and
HDW-xBR Models
HDW-xB, HDW-xBN, and HDW-xBR models are built-in units
that require installation into a cabinet before operation.
WARNING
ELECTRIC SHOCK HAZARD: Built-in units must be
installed by a qualified electrician. Installation must
conform to all local electrical codes. Installation by
unqualified personnel will void unit warranty and may lead
to electric shock or burn, as well as damage to unit and/
or its surroundings.
1. Cut the appropriate opening in the cabinet. Refer to the
“Built-In Cutout Dimensions” chart and illustration for
dimensions.
NOTE: Maintain a minimum clearance of 25 mm (1″) between
the cutout opening and the floor.
2. Fasten a locking strip (not supplied) to the lower front
inside lip of the cabinet opening.
3. Make sure a properly grounded electrical supply of the
correct voltage and size is installed inside the cabinet
cutout. See the SPECIFICATIONS section for details.
4. Partially insert the unit into the opening, making sure the
conduit is fed into the opening first.
5. Have a qualified electrician connect the unit wires from the
conduit to the electrical supply inside the cabinet.
6. Before installing the unit into the opening completely,
apply a bead of National Sanitation Foundation-approved
sealant between the heated drawer flange and the cabinet
facing.
7. Slide the unit into the opening until the front locking studs
drop behind the locking strip. To verify installation, pull out
the bottom drawer completely and gently pull to ensure the
unit is locked in place.
Heated
Drawer
Flange
Locking
Strip
Cabinet
Facing
Locking Studs
(underneath)
Built-In Installation (HDW-2B Model shown)
A
25 mm
(1″)
C
B
Front View Side View
22 mm
(7/8″)
3 mm
(1/8″)
Locking
Strip
Locking
Strip
Cutout and Locking Strip Dimensions
Model
Width
(A)
Depth
(B)
Height
(C)
HDW-1B 720 mm
(28-3/8″)
610 mm
(24″)
257 mm
(10-1/8″)
HDW-2B 720 mm
(28-3/8″)
610 mm
(24″)
514 mm
(20-1/4″)
HDW-3B 720 mm
(28-3/8″)
610 mm
(24″)
771 mm
(30-3/8″)
HDW-1BN 502 mm
(19-3/4″)
720 mm
(28-3/8″)
257 mm
(10-1/8″)
HDW-2BN 502 mm
(19-3/4″)
720 mm
(28-3/8″)
514 mm
(20-1/4″)
HDW-3BN 502 mm
(19-3/4″)
720 mm
(28-3/8″)
771 mm
(30-3/8″)
HDW-1BR 722 mm
(28-7/16″)
460 mm
(18-1/8″)
257 mm
(10-1/8″)
HDW-2BR 722 mm
(28-7/16″)
460 mm
(18-1/8″)
530 mm
(20-7/8″)
HDW-3BR 722 mm
(28-7/16″)
460 mm
(18-1/8″)
803 mm
(31-5/8″)
Built-In Cutout Dimensions
INSTALLATION

Form No. HDWM_CN-0817
12
English
OPERATION
General
Use the following procedure to operate a Hatco Drawer Warmer.
Each drawer can be controlled and monitored individually using
the adjustable drawer vents for humidity control as well as the
POWER I/O (on/off) switch, TEMPERATURE control knob, and
temperature monitor.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Startup
1. For freestanding units, plug the unit into a properly
grounded electrical receptacle of the correct voltage, size,
and plug configuration. See the SPECIFICATIONS section
for details.
2. Move the Power I/O (on/off) switch(es) to the I (on) position.
3. Turn the TEMPERATURE control knob(s) to the desired
setting(s). See the Recommended Settings chart on the
control panel or the Food Holding Guide in this section.
CAUTION
Standard and approved manufacturing oils may smoke up
to 30 minutes during initial startup. This is a temporary
condition. Operate unit without food product until smoke
dissipates.
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Use caution when opening drawer. Hot air escapes
when drawer is open.
4. Allow unit 15–20 minutes to reach operating temperature.
5. Adjust the drawer vents for the desired humidity by sliding
the vent knob on the drawer front. Move vent knob to the
right to open the vents and to the left to close the vents.
Opening the vents all the way allows maximum moisture
to escape.
Drawer Vents
Vent Knob
Drawer Vent
NOTE: Proper vent adjustment depends on the type and amount
of food held, as well as the frequency of drawer opening.
NOTE: For additional moisture, water can be added
(approximately 6 mm [1/4″] of water) to the optional
water/spillage pan before inserting the food pan into
the drawer. Check water level periodically. Add water
as necessary. Use of splash baffle is recommended to
prevent water from splashing into the cabinet interior
when opening and closing a drawer. If hard water is
used, the pan will require periodic cleaning and deliming.
See Maintenance section for deliming instructions.
NOTE: Damage caused by water is not covered under warranty.
Shutdown
1. Move the Power I/O (on/off) switch(es) to the O (off)
position.
2. Allow the unit to cool before performing any cleaning or
maintenance.
Temperature
Monitor
RECOMMENDED
SETTINGS Chart
TEMPERATURE
Control Knob
POWER I/O
(on/off) Switch
Drawer Warmer Control Panel
Food Holding Guide
Recommended Type of Vent
Product Storage Temperature Heat Setting
Rolls, Hard 71°–85°C (160°–185°F) Dry Open
Rolls, Soft 66°–79°C (150°–175°F) Moist Open-Half
Vegetables 79°–85°C (175°–185°F) Moist Open-Half
Meat, Poultry 74°–85°C (165°–185°F) Dry Open
Fish 74°–85°C (165°–185°F) Moist Closed
Casseroles 66°–79°C (150°–175°F) Dry Open
Pies, Desserts 71°–85°C (160°–185°F) Dry Open
Tacos, Tortillas 66°–71°C (150°–160°F) Moist Open-Half

Form No. HDWM_CN-0817 13
English MAINTENANCE
Removing Lime and Mineral Deposits
(models with optional water pan)
Use the following procedure for periodic cleaning and deliming
of the water pan.
NOTE: The lime and mineral content of the water used for
daily operation will determine how often the deliming
procedure must be performed.
NOTE: Perform this procedure when the unit will not be used
for a period of time, such as the end of the day.
1. Turn off the unit, unplug the power cord (freestanding
models), and allow the unit to cool.
2. After the unit has cooled, remove and empty the water
pan.
3. Fill the water pan with a mixture of 75% water and 25%
white vinegar to a level where it covers the lime and
mineral deposits.
4. Install the water pan with deliming solution into the unit.
5. Plug in and turn on the unit. Allow the unit to run for 30
minutes.
6. Turn off the unit and unplug the power cord (freestanding
models).
7. Allow the water pan to stand with the deliming solution for
at least two hours (the time required will vary depending
on the amount of deposits in the water pan).
8. Remove the water pan and empty the deliming solution.
9. Continue to fill and rinse the water pan with clean water
until the pan is clean.
10. Install the clean water pan into the unit. Plug in the unit and
fill the water pan as usual for daily operation (6 mm [1/4″]
of water is recommended).
NOTE: If lime and mineral deposits are still present in the water
pan, repeat this procedure and increase the amount of
time the de-liming mixture stands in the water pan.
General
Hatco Drawer Warmers are designed for maximum durability
and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord/turn off
power at circuit breaker, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact Hatco at [phone].
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
1. Turn off the unit, unplug the power cord (freestanding
models), and allow the unit to cool.
2. Remove and wash all food pans and accessories.
3. Wipe down surfaces using a damp cloth. A non-abrasive,
cream cleaner may be used for difficult stains.
• Make sure to check and clean the interior of the unit.
Food pieces may fall from the food pans into the drawer
cavity. CAUTION! Burn Hazard—Do not clean drawer
cavity when unit is on!
4. Wipe the entire unit dry using a clean, dry cloth.

Form No. HDWM_CN-0817
14
English
Symptom Probable Cause Corrective Action
Unit too hot. TEMPERATURE control set too high. Change the temperature to a lower setting.
Unit connected to incorrect power supply. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Unit not hot enough. Unit not allowed enough time to preheat. Allow unit 15–20 minutes to reach operating
temperature.
Temperature control set too low. Change the temperature to a higher setting.
Drawer(s) not closed completely. Make sure all drawers are closed completely.
Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Product too dry. Drawer vent in open position. Move drawer vent to closed position.
Optional water pan empty or not installed. Install and/or fill water pan with clean water. Control
level of moisture using drawer vents.
Product too moist. Drawer vent in closed position. Move drawer vent to open position.
Optional water pan installed, but not needed. Remove water pan from drawer.
Unit not working at all. Unit not plugged in. Plug unit into proper power supply.
Unit not turned on. Move POWER I/O (on/off) switch to the I (on) position.
Circuit breaker tripped. Reset circuit breaker.
Power I/O (on/off) switch defective. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Internal thermostat defective. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
Heating element burned out. Contact an Authorized Hatco Service Agent or Hatco
for assistance.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by trained and qualified
personnel only. Service by unqualified personnel may lead
to electric shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, adjustments, or maintenance.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco
for assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com and click on
Find Service Agent, or contact the Hatco Parts and Service Team at:
Telephone: [phone]
e-mail: [email protected]

Form No. HDWM_CN-0817 15
English OPTIONS AND ACCESSORIES
Digital Temperature Controller
The digital temperature controller is factory installed and takes
the place of the standard drawer warmer control panel. Use
the following procedure to operate the digital temperature
controller.
Startup
1. Move the Power I/O (on/off) switch(es) to the I (on) position.
• The corresponding digital temperature controller will
energize and the current temperature of the drawer or
“LO” will appear on the TEMPERATURE display. “LO”
indicates the drawer temperature is below 21°C (70°F).
2. Press the key three times to verify the setpoint
temperature. (“SP” will be displayed after the second
press.) See the RECOMMENDED SETTINGS chart on
the control panel or the FOOD HOLDING GUIDE in this
manual.
• The setpoint temperature will be shown for 10 seconds.
After 10 seconds, the TEMPERATURE display will revert
to the current temperature of the unit. To change the
setpoint temperature, refer to “Changing the Setpoint
Temperature” in this section.
NOTE: The digital temperature controller is pre-set to a setpoint
temperature of 85°C (185°F) at the factory. Once the
setpoint temperature is changed, the new setpoint
temperature will remain in memory until it is changed
again. The minimum to maximum setpoint temperature
range is 21°C (70°F) to 93°C (200°F).
CAUTION
BURN HAZARD:
• Some exterior surfaces on unit will get hot. Use caution
when touching these areas.
• Use caution when opening drawer. Hot air escapes
when drawer is open.
3. Allow unit 15–20 minutes to reach operating temperature.
Shutdown
1. Move the Power I/O (on/off) switch to the O (off) position.
The digital temperature controller and heated drawer will
shut off.
Changing the Setpoint Temperature
Use the following procedure to change the setpoint temperature.
1. Press the key three times. The current setpoint
temperature will be shown on the TEMPERATURE display
(“SP” will be displayed after the second press).
2. Press the key or key within 10 seconds to change
the setpoint temperature.
3. Press the key to lock in the new setpoint temperature.
The TEMPERATURE display will go blank for two seconds
to show that the new setting has been accepted.
NOTE: After 10 seconds of inactivity during the programming
process, the controller will exit programming mode
automatically without saving any changes.
Changing Fahrenheit and Celsius Setting
Use the following procedure to change between Fahrenheit
and Celsius on the display.
1. Press the key once. Either an “F” for Fahrenheit or “C”
for Celsius will be displayed.
2. Press the key or key within 10 seconds to change
between “F” (Fahrenheit) and “C” (Celsius).
3. Press the key three times to lock in the new setting.
The TEMPERATURE display will go blank for two seconds
to show that the new setting has been accepted.
NOTE: After 10 seconds of inactivity during the programming
process, the controller will exit programming mode
automatically without saving any changes.
Digital
Temperature
Controller
RECOMMENDED
SETTINGS Chart
POWER I/O
(on/off)
Switch
Control Panel with Digital Temperature Controler

Form No. HDWM_CN-0817
16
English
76mm(3″)LockingCasters
76 mm (3″) locking casters are available for the one, two, and
three-drawer freestanding units in place of the legs. Add 4 mm
(3/16″) to Height (C) in Dimensions section. Use the following
procedure to install casters onto the bottom of the unit.
NOTICE
Do not lay unit on the front or back side or damage to the
unit could occur.
1. Remove any pans from the drawers of the unit.
2. Carefully lay the unit on its left or right side (requires two
people).
3. Remove the legs, if installed.
4. Install the caster into a hole where a leg was removed.
Tighten securely.
76 mm (3″) Caste
r
Installing 76 mm (3″) Casters
5. Repeat steps 3 and 4 for the remaining three casters.
6. Return the unit to the upright position (requires two
people).
51mm(2″)LockingCasters
51 mm (2″) diameter locking casters are available for one, two,
and three drawer freestanding units. Subtract 37 mm (1-1/2″)
from Height (C) in Dimensions section.
102mm(4″)LockingCasters
102 mm (4″) diameter locking casters are available for one,
two, three, and four drawer freestanding units. Subtract
22 mm (7/8″) from Height (C) in Dimensions section for 4
drawer models.
127mm(5″)LockingCasters
127 mm (5″) diameter locking casters are available for one, two,
three, and four drawer freestanding units. Add 5 mm (3/16″) to
Height (C) in Dimensions section for 4 drawer models.
6″(152mm)AdjustableLegs
152 mm (6″) stainless steel adjustable legs are available for
one, two, three, and four drawer freestanding units. Add 0 mm
(0″) to Height (C) in Dimensions section for 4 drawer models.
Oversized Drawer
An oversized drawer and pan is available as a factory installed
option. The pan measures 508 x 381 x 127 mm (20″W x 15″D
x 5″H).
Biscuit Drawer
A biscuit drawer is available as a factory installed option. Biscuit
drawers accommodate two 457 x 330 mm (18″W x 13″D) half-
size sheet pans (pans not included).
Food Pans
Accessory stainless steel food pans are available in various
sizes.
ALUM PAN: Half-size sheet pan at 457 x 330 mm (18″W x 13″D)
ST PAN 2: Full size stainless steel pan at 64 mm (2-1/2″) deep
— 324 x 527 x 64 mm (12-3/4″W x 20-3/4″D x 2-1/2″H)
ST PAN 4: Full size stainless steel pan at 102 mm (4″) deep —
324 x 527 x 102 mm (12-3/4″W x 20-3/4″D x 4″H)
ST PAN 1/2 x 6”: Half size stainless steel pan at 152 mm (6″)
deep — 324 x 264 x 152 mm (12-3/4″W x 10-3/8″D x 6″H)
HDW 6″ PAN: Full size stainless steel pan at 152 mm (6″)
deep — 324 x 527 x 152 mm (12-3/4″W x 20-3/4″D x 6″H)
Full Pan
64 mm (2-1/2″) Deep Full Pan
102 mm (4″) Deep
Full Pan
152 mm (6″) Deep
Stainless Steel Food Pans
Water/Spillage Pan
The water/spillage pan fits in the drawer underneath the
food pan and can be used to humidify the heating area
or keep spillage from the cabinet interior. A Splash baffle is
recommended for use with a water/spillage pan.
Splash Baffle
The splash baffle is used with the optional water/spillage pan.
Fabricated of stainless steel, the baffle fits into the bottom of
the water/spillage pan, over the water bath. The splash baffle
prevents water from splashing into the cabinet interior when
opening and closing a drawer, while allowing humidity to
escape.
Chip Guard
The chip guard completely shields the heating element,
preventing any food product, such as tortilla chips, from coming
in contact with the heating element.
Trivet
A trivet (HDW-TRIVET) raises food product 51 mm (1/2″) off the
bottom of a full size food pan.
OPTIONS AND ACCESSORIES

Form No. HDWM_CN-0817 17
English INTERNATIONAL LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions
or 18 months from the date of shipment from Hatco. Buyer
must establish the Product’s purchase date by registering the
Product with Hatco or by other means satisfactory to Hatco in
its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) Two (2) Year Parts Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Case Elements (metal sheathed air heating)
Heated Well Elements — HWB Series (metal sheathed)
b) Five (5) Year Parts Warranty:
3CS and FR Tanks
c) Ten (10) Year Parts Warranty:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
d) Ninety (90) Day Parts Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely to replacement of part or Product using, at
Hatco’s option, new or refurbished parts or Product by Hatco
or a Hatco-authorized service agency with respect to any
claim made within the applicable warranty period referred to
above. Hatco reserves the right to accept or reject any such
claim in whole or in part. In the context of this Limited Warranty,
“refurbished” means a part or Product that has been returned
to its original specifications by Hatco or a Hatco-authorized
service agency. Hatco will not accept the return of any Product
without prior written approval from Hatco, and all such approved
returns shall be made at Buyer’s sole expense. HATCO WILL
NOT BE LIABLE, UNDER ANY CIRCUMSTANCES, FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING
BUT NOT LIMITED TO LABOR COSTS OR LOST PROFITS
RESULTING FROM THE USE OF OR INABILITY TO USE
THE PRODUCTS OR FROM THE PRODUCTS BEING
INCORPORATED IN OR BECOMING A COMPONENT OF
ANY OTHER PRODUCT OR GOODS.
SERVICE INFORMATION
The warranty on this Hatco unit is for one year from date of
purchase or eighteen months from date of shipping from Hatco,
whichever occurs first.
If you experience a problem with this unit during the warranty
period, please do the following:
Contact Local Hatco Dealer
When contacting the Hatco dealer for service assistance,
please supply the dealer with the following information to
ensure prompt processing:
• Model of unit
• Serial number (located on the unit)
• Specific problem with the unit
• Date of purchase
• Name of business
• Shipping address
• Contact name and phone number
The Hatco dealer will do the following:
• Provide replacement part(s) as required
• Submit warranty claim to Hatco for processing
Non-Warranty Problems
If you experience a non-warranty problem that requires
assistance, please contact the nearest Authorized Hatco
Service Agency.
To locate the nearest Service Agency:
• call Hatco at [phone]
• e-mail Hatco at [email protected]

表号：HDWM_CN-0817
18
中文
目录
简介
使用者重要注意事项
本手册中的安全信息采用以下标志表示：
“警告”表示有危险情况，如果不加以避免，则可能导致
人身伤亡。
“小心”表示有危险情况，如果不加以避免，则可能导致
轻度或中度人身伤害。
“注意”用于提示不会涉及人身伤害的操作。
赫高抽屉式保温柜能将食品保持在最佳食用温度而不影响其品
质。 产品采用坚固的不锈钢结构、重型五金件、不锈钢导轨
以及可自动关闭的抽屉，是专为要求严苛的厨房制造。 抽屉
式保温柜可以使所有食品（包括肉类、蔬菜和面包卷）在供应
时仍保持适宜温度及鲜美风味。
多重抽屉设备，每个抽屉均设有单独的控制装置，可以在服务
高峰期存放更多种类的热食。
赫高抽屉式保温柜是经过大量研究和现场测试才投入生产的产
品。 所用材料经久耐用，外型美观，性能优异。 所有设备在
发货前都经过严格的检验和测试。
本手册包含抽屉式保温柜的安装、安全和操作说明。 在安装
或操作设备之前，赫高建议您先阅读本手册中所有的安装、操
作和安全说明。
请在下列空白处记下本设备的型号、序列号、电压、和购买日
期 （立式设备位于背侧，嵌入式设备则位于右侧面板内侧）
。致电 Hatco 要求服务帮助时请提供上述信息。
型号 _________________________________________
序列号 _______________________________________
电压 _________________________________________
购买日期 _____________________________________
工作时间： 北京时间 上午 9:00 – 下午 6:00 周一至周五
电话： [phone]
E-mail: [email protected]
传真： [phone]
查询更多信息请访问我们的网站：www.hatcocorp.com
使用者重要注意事项.................................. 18
简介 ............................................... 18
重要安全说明........................................ 19
型号说明............................................ 20
型号命名............................................ 20
规格 ............................................... 21
插头型式 .......................................... 21
电气参数表 ........................................ 21
食品存放容量 ...................................... 23
尺寸 .............................................. 24
安装 ............................................... 26
总则 .............................................. 26
安装 HDW-x 以及 HDW-xN 型号 ....................... 26
安装 HDW-xB、HDW-xBN 以及 HDW-xBR 型号 ............ 27
操作 ............................................... 28
总则 .............................................. 28
维护 ............................................... 29
总则 .............................................. 29
日常清理 .......................................... 29
清除石灰和矿物沉淀 ................................ 29
故障处理指南........................................ 30
选项和配件.......................................... 31
全球有限质保........................................ 33
服务信息............................................ 33

表号：HDWM_CN-0817 19
中文 重要安全说明
使用本设备前，请仔细阅读下列重要安全事项，以免造成严重的人身伤亡及设备或财产的损坏。
爆炸危险：请勿在设备或其它电器周围储存或使用汽油类或其
它易燃气体和液体。
确保食品在放入设备前已被加热至适当的食品安全温度。 未能
正确加热食品可能会导致严重的健康风险。 本设备仅限存放预
热食品。
赫高公司对食品的实际供应温度不承担责任。 用户有责任确保
食品在安全的温度下存放和供应。
确保所有操作人员受过安全正确使用设备的培训。
本设备未针对儿童和体质偏弱、过敏和精神失常人群使用做相
应设计。确保对儿童进行适当看管，使他们远离设备。
本设备不含“用户维修”零部件。如需维修，请联系HATCO授
权服务机构或HATCO服务部门，电话 [phone]；传
真 [phone]。
烫伤危险：
• 本设备的某些外表面处温度较高，接触这些部位时请务必
小心。
• 打开抽屉时务必小心。 抽屉打开时会有热气逸出。
将设备置于便于使用的区域。 放置区域应当呈水平状态，且足
够结实，能够承受本设备和存放食品的重量。
请勿正面向下或背面向下放置设备。 可能会损坏设备。
只允许使用非摩擦性清洁剂。摩擦性清洁剂可能会刮伤本设备
的表面处理层，破坏其外观，并易使表面积尘。
设备需要每日清洁，以免出现故障，操作时请保持卫生。
请勿将设备置于气流过急的环境中。 避免将设备放在空气流动
或气流活跃的区域（即排气扇/排风罩、空调管和外门附近）。
触电危险：
•将设备插头妥善插入有接地的电气插座内，插入前请核对电
压、规格和插头型式是否正确。如果插头和插座不匹配，请
和有正式资格的电工联系，以确定并安装电压和规格正确的
电气插座。
•嵌入式设备需由具备相应资质的电工安装。 安装时必须
遵循所有的当地电气规程。 若由不具备相应资质的人员安
装，则可能引起触电或着火，以及设备和/或其周围环境的
损毁。
•在进行任何清洁、调整或维护之前，请先关闭电源开关，
拔下电源线/关掉断路器电源，并使设备冷却。
•禁止将设备浸入水中。本设备不防水。 严禁使用被水浸过
的设备。
•本设备不具备耐候性。请将本设备置于室内，室内气温不
得低于(21°C) 70°F。
•请不要在设备通电或尚未冷却时进行清洁。
•不得用蒸汽或使用过多的水清洁设备。
•本设备不具备防喷淋结构。请勿使用喷淋头清洁本设备。
•请勿用电源线拖拽本设备。
•如果电源线磨损或者破损，请停止使用。
•如果电源线出现磨损，不要试图自行维修或更换。电源线
必须由HATCO、HATCO授权服务机构或具备类似资质的
人员进行更换以免发生危害。
•本设备必须由具备相应资质的人员进行维修。由不具备相
应资质的人员维修可能导致触电或起火。
•不要让液体溅入设备。
•维修时只能使用正品HATCO更换零部件。未使用正品
HATCO更换零部件会导致质保失效及造成设备操作人员受
到有害电压威胁，并引起触电或着火。正品HATCO更换零
部件可以保证使用环境下的安全生产，某些普通零部件不具
备相关特性，从而无法保证在HATCO设备的安全使用。
火灾危险：
•将设备放置在距离可燃墙壁或材料至少1英寸 (25 mm) 的
地方。如果不能保持安全距离，则可能引起褪色或燃烧。
•请勿使用漂白剂（或含漂白剂的清洁剂）、烤箱清洁剂或
易燃的清洁溶液等刺激性化学物质清洁本设备。

表号：HDWM_CN-0817
20
中文
型号说明
型号命名
H D W - x x
ৠ฽ ெᏍ࠲!>!அ໮
N >!அ໮Ȃየ໮
B >!෍๠໮
BN >!෍๠໮Ȃየ໮
BR >!෍๠໮Ȃ්໮
ڨ࿘໮֦ၫࣤ
ڨ࿘༮஢
所有型号
所有赫高抽屉式保温柜均采用坚固耐用的镀铝不锈钢、耐用尼
龙辊、12 号不锈钢导轨及重型五金件制造。 每个抽屉均具
备用以控制湿度的可调式抽屉排气口、电源 I/O（开/关）开
关、温度控制旋钮和温度监测器。 每个抽屉均配备 152 毫米
( 6 英寸）标准尺寸餐盘。 绝缘顶部和侧面提供最大能效，加
热元件保修两年。
HDW-x 型号
HDW-x 型号为立式设备，可用于一层、二层、三层、四层抽屉
版本。 一层、二层、三层抽屉设备配备 102 毫米 (4 英寸）
脚架。 四层抽屉设备配备 152 毫米（6 英寸）不锈钢脚架。
立式型号包括随附的带插头的 1829 毫米（6 英寸）电源线。
HDW-xN 型号
HDW-xN 型号具备 HDW-x 立式型号的所有功能，但采用更窄
的外形以满足较小的空间要求。 这些设备可用于一层、二层、
三层抽屉版本。
ڨ࿘ഠනଁ
ݢኑ!I/O˄܏૑0࣋ט˅૑࣋
ၫޡ৭كධ
ၫޡ૿፟ᅢഀ
HDW-2 型号
注意： 立式设备有额外的脚轮和脚架尺寸可供选择。 有关详细
信息，请参阅“选件及配件”部分。
HDW-xB 型号
HDW-xB 型号为嵌入式设备，可用于一层、二层、三层抽屉版
本。 嵌入式 HDW-xB 型号含 。
1219 毫米（4 英寸）软导线用于直流电源连接。
HDW-xBN 型号
HDW-xBN 型号具备 HDW-xB 型号的所有功能，但采用更窄
的外形以满足较小的空间要求。 这些设备可用于一层、二层、
三层抽屉版本。
ڨ࿘ഠනଁ
ၫޡ৭كධ
ݢኑ!I/O˄܏૑0࣋ט˅૑࣋
ၫޡ૿፟ᅢഀ
HDW-2B 型号
HDW-xBR 型号
HDW-xBR 型号具备 HDW-xB 型号的所有功能，但采用更浅
的深度以满足较小的空间要求。 这些设备可用于一层、二层、
三层抽屉版本。