haupa AS-52 User manual

...convincing solutions
Battery powered cab ecutter
„AS-52“
Art. 216434-1
INSTRUCTION MANUAL
Battery cutting tool
Video 216434

1. Technica data
Area of application: Separating copper and aluminium cables
Not suitab e for fine stranded conductors and ACSR
a uminum stee cab es.
Safety: Working Safely with safety lever.
The model Art. 216434 does not protect the operator when
working on cables that carry power.
Garantie: 2 year guarantee if used for the purpose it is intended.
2. Area of work
Cutting range: Ø till 52 mm Cu/Al
Battery charging time in minutes: 60 min.
Battery type: 18 V, 4 Ah

Germany: HAUPA GmbH & Co. KG, Königstraße 165-169, D- 42853 Remscheid.
Phone: [phone], Fax: [phone], [email protected] • Errors and technical changes reserved.
...convincing solutions
eng ish
3. Short description
Preparation:
Before starting up the tool, always read the operating instructions.
All current-carrying elements in the area you are working in should be disconnected.
therwise the protective procedures for working in the vicinity of components under current
must be implemented. (DIN EN 50110)
Do not use the tool if you are tired or under the influence of medication, drugs or alcohol.
Take into account the valid accident prevention and safety regulations and use the tool exclu-
sively for the purpose for which it is intended.
nly electro-technically trained persons over 16 years of age may process connecting materi-
als using the tool.
The operating instructions must always be carried with the tool.
The instructions must have been read and understood by the user.
The operator must ensure that this is the case.
Handling:
• The device has a manual return that brings the piston back to the starting point when
the maximum cutting force (separation of the cable) has been achieved.
• Particularly excellent circular cut
• Use under the harshest conditions possible - robust construction.
Rotary knife
Pushbutton
Safety lever

4. Notes regarding correct use
Before you start work, all active, thus current-carrying elements in the area around the
assembler must be switched to without power. If this is not possible, protective procedures for
working in the vicinity of components under current must be implemented. The charge status
of the battery should be checked before you start work.

HAUPA GmbH & Co. KG, Königstraße 165-169, D-42853 Remscheid,
Tel.: [phone]. Fax: [phone], E-Mail: [e-mail]. Subject to technical changes and printing errors.
... convincing solutions
english
Mounting and unmounting the battery
Charger specifications
Model Nr.: 215527
Input: 100 – 240 V AC
Frequency: 50 / 60 Hz
Output V: 21 V
Output A: 1 A
Weight: 0,164 kg
Measurements: 92 mm (L) x 47 mm (B) x 45 mm (H)
Charger: Connecting battery to charger:

215523 (2 Ah) 215525 (4 Ah)
Please remove the battery after use and keep it removed when storing the
tool!
HAUPA is not liable for wrong or unintended use
2 Ah Battery Specifications
Model Nr.: 215523
Voltage: 18 V
Weight: 0,35 kg
Measurements: 114 mm (L) x 73,5 mm (B) x 67 mm (H)
est. Charging Time: approx. 30 Min
Capacity: 2 Ah
4 Ah Battery Specifications
Model Nr.: 215525
Voltage: 18 V
Weight: 0,58 kg
Measurements: 114 mm (L) x 73,5 mm (B) x 67 mm (H)
est. Charging Time: approx. 60 Min
Capacity: 4 Ah
LED charge indicator: (Pressing the button will light up LEDs)

6. Care and aintenance
Cleaning
• Careful cleaning of the tool, in particular, the moving parts contributes towards a longer
useful life. Remember that dust, sand, environmental influences, in particular a high salt
index, and dirt in general are extremely damaging.
•When inserting the rotary knife into gear, use the pushbutton. Pushing it into gear with
force may cause damage to the knife and the gear.
Power switch
Check to see whether the switch on the machine automatically pops out again when you
release it.
Storage
To prevent damage to the tool as a result of bumps, dust etc. you should if possible store the
tools in the original packaging.
Guarantee:
2 year guarantee when used for the purpose it is intended when the annual maintenance inter-
vals are maintained by an authorised HAU A service centre. We reserve the right to rework the
product.
Disposal:
…in accordance with the scope of validity of the European WEEE (2002/96/EU) and RoHS
directives (2002/95/EU). Batteries must be disposed off separating according to the battery
directive.
WITH EVERY RE LACEMENT ART ORDER, INCLUDE THE FOLLOWING INFORMATION:
1) Article number.
2) Article description.
3) Reference to the operating instructions and/or date.
4) Tool type.
5) Serial number of the tool.
The guarantee is voided if you use parts that are not original replacement parts from HAU A.

HAUPA GmbH & Co.KG, Königstr. 165-169, 42853 Remscheid, Germany
D
D
e
e
c
c
l
l
a
a
r
r
a
a
t
t
i
i
o
o
n
n
o
o
f
f
c
c
o
o
n
n
f
f
o
o
r
r
m
m
i
i
t
t
y
y
H
H
A
A
U
U
P
P
A
A
F
F
a
a
c
c
t
t
o
o
r
r
y
y
c
c
e
e
r
r
t
t
i
i
f
f
i
i
c
c
a
a
t
t
e
e
Remscheid, 25.02.2021
product: battery cable cutter “AS-52”
product range: Around the cable
product no.: 216434-1
battery: 18 V, 4,0 Ah, Li-Ion
weight: 2,7 kg
diameter: max. Ø 52 mm
range of application: Al / Cu cable max. Ø 52 mm
dimension: 320 x 160 x 110 mm
remark: not for ACSR and armoured cables
We, Haupa GmbH & Co KG, with the main Headquarter in 42853 Remscheid/Germany,
Koenigstrasse 165-169, declare under our sole responsibility that the products mentioned in
the data sheet complies with the European Standards or Standard Documentations according
to the regulations of the following mentioned directives:
According to 2006/42/EG, 2014/30/EU
HAUPA GmbH & Co.KG
Productmanagement