Hausmann 1300 Installation instructions

rev. 11.27.07 cjr ©2007 HAUSMANN INDUSTRIES, INC.
HAUSMANN INDUSTRIES, INC.
130 Union St • Northvale NJ 07647 USA • Tel: [phone] • Fax: [phone] • www.hausmann.com
Installation/Operation Instructions
Models 1300, 1302, 1390, 1392, 1393 - Parallel Bars
PARTS LIST
PART PART # QTY. PART DESCRIPTION:
A 1300-001 4 ‘T’ Fitting
B 1300-002 4 ‘T’ Fitting With Control Knob
C 1300-003 2 Handrail (See Chart Below)
D 1300-004 4 Adjustable Height Post
E 1300-005 4 Locking Pin W/chain
F 1300-006 4 Upright
G 1300-007 1 Platform Base
H 1300-008 16 5/16 X 1 1/2” Bolt W/ Lock Washer
I 1300-009 4 Adjustable Width Fitting (1390 &1392)
J 1300-010 4 Control Knob (1390 & 1392)
K 1300-011 11 Ladder Steps (1393 Only)
L 1300-012 1 Balance Beam, 89 3/4”l X 6”w X 3 3/8”h (1393 Only)
UNIT SIZES FOR DIFFERENT MODELS:
MODEL WIDTH LENGTH HEIGHT
1300 26” 10’ 28”-41”
1302 26” 12’ 28”-41”
1390 15”-28” 10’ 29”-42”
1392 15”-28” 12’ 29”-42”
1393 15”-28” 10’ 29”-42”
D
E
J
G
FA
C
I
B
1
Please join Hausmann’s effort to reduce
paper use and keep the planet green by
using our paperless Warranty Registration
form. Visit www.hausmann.com and click
on Warranty Registration. If you do not
have web access or prefer the form be mailed or faxed
to you, please call Hausmann Customer Service.
As of January 1, 2010, we will no longer include the
paper based forms, please visit the online link to fill in
your Warranty Form.

rev. 11.27.07 cjr ©2007 HAUSMANN INDUSTRIES, INC.
'T' FITTING
PLATFORM BASE
UPRIGHT
ADJUSTABLE
HEIGHT POST
HANDRAIL
5/16 X 1 1/2" BOLT
W/WASHER
LOCKING PIN W/
CHAIN
UPRIGHT
PLATFORM BASE
LOCKING PIN W/
CHAIN
ADJUSTABLE
HEIGHT POST
UPRIGHT
'T' FITTING
5/16 X 1 1/2" BOLT
W/WASHER
WIDTH
ADJUSTABLE
FITTING
HANDRAIL
UPRIGHT
LOCKING PIN
ADJUSTABLE
HEIGHT POST
WIDTH
ADJUSTABLE
FITTING
LOCKING PIN
"T" FITTING
1300 and 1302 Parallel Bars
1390. 1392 and 1393 Parallel Bars
Installation Instructions for 1300 & 1302
1. Place Uprights on Platform Base as shown in
Illustrations.
2. Secure Uprights to Platform Base with 5/16 x
1 1/2” Bolts and Lock Washers supplied by
Hausmann.
3. Attach the Parallel Bars to the Uprights. To
attach the Parallel Bars to the Uprights, just
simply place the “T” fittings (attached to Parallel
Bars) onto the Adjustable Height Posts in the
Uprights.
4. Repeat steps 3 for other bar.
5. Once everything is in place, tighten all the Allen
Screws on the “T” fittings with Allen Wrench
provided.
Installation Instructions for 1390, 1392 & 1393
1. Place Uprights on Platform Base as shown in
Illustrations.
2. Secure Uprights to Platform Base with 5/16 x
1 1/2” Bolts and Lock Washers supplied by
Hausmann.
3. Attach the Parallel Bars to the Uprights. To
attach the Parallel Bars to the Uprights, just
simply place the “T” fittings (attached to
Adjustable Width fitting which are attached to
the Parallel Bars.) onto the Adjustable Height
Posts in the Uprights.
4. Repeat steps 3 for other bar.
5. Once everything is in place, tighten all the Allen
Screws on the “T” fittings with Allen Wrench
provided.
Parallel Bar Height Adjustment
1. Remove Locking Pin from the Upright.
2. Raise or lower the Adjustable Height Post to
desired height.
3. Insert the Locking Pin into the Upright, through
the Adjustable Height Posts and all the way
through the other side of the Upright.
Parallel Bar Width Adjustment -
1390 & 1392 Only
1. To loosen the Width Adjustable fitting, turn the
Control Knob clockwise.
2. Move the Width Adjustable fitting in or out to
desired width.
3. Tighten the Control Knob by turning
counterclockwise.
Width AdjustmentHeight Adjustment
Note: Use innermost
(4) holes to mount.
Note: Use outermost
(4) holes to mount.
2

rev. 11.27.07 cjr ©2007 HAUSMANN INDUSTRIES, INC.
A
B
C
DETAIL 'A'
STEPS
(K)
PLAN WITH
LADDER STEPS
INSTALLED
# 1393 Step Ladder
The Placement of Ladder Steps:
Alternate the steps by inserting one holes “B” and “C”,
then the second in “A” and “B”. Continuing as required
(see detail A above).
B
BALANCE BEAM
(L)
PLAN WITH
BALANCE BEAM
INSTALLED
DETAIL 'B'
# 1393 Balance Beam
The Placement of Balance Beam:
Fits into the second and second to last holes in line “B” (see detail B above).
NOTE: It is not necessary to remove the ladder steps prior to installing the
balance beam. Balance beam is designed to fit over previously installed steps.
3