Hawg Wired RC-Link RC104 User manual

d
de es si ig gn ne ed d a an nd d b bu ui il lt t i in n t th he e u u. .s s. .a a. .
H
HA AW WG G W WI IR RE ED D
R
R
RC
C
C1
1
10
0
04
4
4
R
R
RC
C
C-
-
-L
L
LI
I
IN
N
NK
K
K™
™
™ R
R
RE
E
EM
M
MO
O
OT
T
TE
E
E C
C
CO
O
ON
N
NT
T
TR
R
RO
O
OL
L
L
I
IN NS ST TA AL LL LA AT TI IO ON N G GU UI ID DE E

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 2 FREMONT, CA
I
IN NT TR RO OD DU UC CT TI IO ON N
CONGRATULATIONS! YOU’VE JUST PURCHASED WHAT WE CONSIDER TO BE THE FINEST MOTORCYCLE
AUDIO EQUIPMENT AVAILABLE. WE TAKE PRIDE IN THE FACT THAT YOU’VE CHOSEN HAWG WIRED
PRODUCTS, AND WELCOME YOU TO OUR FAMILY OF AUDIOPHILE ENTHUSIASTS. OUR GOAL HERE IS
SIMPLE –TO BRING HIGH PERFORMANCE AUDIO FIDELITY TO YOU, THE RIDER, WITHOUT COMPROMISING
YOUR BIKE’S ELECTRICAL SYSTEM OR STORAGE SPACE. SOME SIDE EFFECTS MAY OCCUR HOWEVER,
INCLUDING BUT NOT LIMITED TO; PUZZLED LOOKS FROM OTHER MOTORISTS, OCCASIONAL SHOUTS
FROM YOUR NEIGHBORS, AND THE ENVY OF YOUR FRIENDS. AFTER YEARS OF DESIGN
AND ENGINEERING, CUSTOM CRAFTSMANSHIP, AND A CRAVE FOR CLEAN, CLEAR,
LOUD MUSIC, WE BELIEVE WE’VE NAILED THIS STUFF DOWN RIGHT.
THANK YOU FOR YOUR SUPPORT
THE HAWG WIRED TEAM
S
SE ER RI IA AL L N NU UM MB BE ER R
PLEASE RECORD THE MODEL AND SERIAL NUMBER[S] OF YOUR EQUIPMENT IN THE SPACE PROVIDED
BELOW AS YOUR PERMANENT RECORD. THESE NUMBERS CAN BE FOUND ON THE FRONT AND/OR
BOTTOM OF EACH COMPONENT. THIS WILL ASSIST US WITH YOUR FACTORY WARRANTY COVERAGE, AND
MAY BE USEFUL TO YOU IN THE UNFORTUNATE EVENT THAT IT’S STOLEN.
MODEL NUMBER[S]:
SERIAL NUMBER[S]:
K
KI IT T C CO ON NT TE EN NT TS S
KIT ITEMS INCLUDED (BY QUANTITY):
RC104
RC104 REMOTE CONTROL MODULE
1
RC-LINK REMOTE CABLE (RJ12 TO RJ12 COILED)
1
RC-LINK COMMUNICATION CABLE (RJ12 TO RJ12 FLAT)
1
PASS-THROUGH COUPLER (RJ12 TO RJ12)
1
PASS-THROUGH COUPLER BRACKET
1

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 3 FREMONT, CA
B
BE EF FO OR RE E Y YO OU U B BE EG GI IN N
THIS SECTION IS INTENDED TO BRING YOU UP TO SPEED WITH OUR DOCUMENTATION CONVENTIONS.
WE RECOMMEND READING THIS MANUAL THOROUGHLY BEFORE BEGINNING YOUR INSTALLATION TO
ACHIEVE A TROUBLE FREE, LONG LASTING OUTCOME.
TERMINOLOGY USED IN THIS MANUAL:
RC-LINK
REFERS TO THE PROPIETARY BUS TECHNOLOGY THAT LINKS MULTIPLE AMPLIFIERS
TO A SINGLE REMOTE CONTROL MODULE. THE GOODS YOU JUST PURCHASED.
RC-LINK MODULE
REFERS TO THE REMOTE CONTROL MODULE ITSELF. THE SMALL GREY AND BLACK
BOX WITH BUTTONS AND LEDS THAT COMES WITH THIS KIT.
POWER AMPLIFIER
CS300, RS400, MASTER 2 CHANNEL AMPLIFIER THAT FUNCTIONS STANDALONE OR
LINKED IN SERIES. IF YOU DON’T OWN ONE OF THESE, YOU’RE OUT OF LUCK.
RC-LINK CABLE
RJ12 TO RJ12 CABLES THAT LINK THE REMOTE MODULE AND AMPLIFIERS
TOGETHER. ONLY USE THE CABLES SUPPLIED WITH THIS KIT.
LOW LEVEL LINK CABLE
3.5MM PHONO JACK CABLE THAT LINK TWO OR MORE AMPLIFIERS TO THE SAME
INPUT SOURCE, ONLY USED IN MULTIPLE AMPLIFIER INSTALLATIONS.
BATWING FAIRING
HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ELECTRA GLIDE (FLHT) MODELS,
FORK MOUNTED, SINGLE HEADLIGHT STYLE.
SHARKNOSE FAIRING
HARLEY-DAVIDSON®TERM FOR THE FAIRINGS ON ROAD GLIDE (FLTR) MODELS,
FRAME MOUNTED (FIXED), DUAL HEADLIGHT STYLE.
MANUFACTURER INSTRUCTIONS
REFERS TO ANY DOCUMENTATION PROVIDED BY A MANUFACTURER OTHER THAN
HAWG WIRED (IE. HARLEY-DAVIDSON®SHOP REPAIR MANUAL, AFTERMARKET
SOURCE UNIT OR SPEAKER MANUAL, ETC.).
QUICK CONNECT SYMBOLS:
KEEP AN EYE OUT FOR THE “QUICK CONNECT” SYMBOLS THROUGHOUT THIS MANUAL; THEY PROVIDE A
VISUAL LINK BETWEEN INSTRUCTIONS, DIAGRAMS, AND THE REMOTE CONTROL CONNECTIONS.
RC-LINK IN
RC-LINK INPUT PORT, REMOTE CONTROL OR AMPLIFIER LINKING
RC-LINK OUT
RC-LINK OUTPUT PORT, AMPLIFIER LINKING
LINE-IN
SOURCE INPUT, LOW LEVEL OR HIGH LEVEL INPUT
LINE-OUT
LOW LEVEL OUTPUT, FEED FOR ADDITIONAL AMPLIFIER DEVICE LINKING
POWER
BATTERY POSITIVE (+12VDC)
FUSE
ESSENTIAL PROTECTION FROM SHORTS
BAD
BATTERY VOLTAGE DEAD, CHECK YOUR CHARGING SYSTEM
OK
BATTERY VOLTAGE OK BUT NOT GREAT, CHECK YOUR CHARGING SYSTEM
GOOD
BATTERY VOLTAGE GREAT, ALL IS WELL, RESUME AUDIO PLAYBACK
CONFIGURE
AMPLIFIER CONFIGURATION AND TEST (GAIN, CROSSOVERS, ETC.)
TOOLS
TOOLS REQUIRED, DISASSEMBLY OR REASSEMBLY WORK TO PERFORM
CAUTION
CAUTIONS, NOTES, TIPS, OR SPECIFIC INFORMATION TO BE AWARE OF
NOTE: IF ANYTHING ABOUT THE INSTRUCTION OR INFORMATION PROVIDED IN THIS MANUAL IS UNCLEAR, QUESTIONABLE,
OR YOU THINK WE’RE DEAD WRONG ABOUT SOMETHING, PLEASE CONTACT US.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 4 FREMONT, CA
I
IN NS ST TA AL LL LA AT TI IO ON N I IN NS ST TR RU UC CT TI IO ON NS S
RC-LINK CONTROL CONNECTIONS
FOR FAIRING REMOVAL AND RE-ASSEMBLY INSTRUCTIONS, REFER TO YOUR AMPLIFIER INSTALLATION MANUAL OR
MANUFACTURER INSTRUCTIONS. AND WHILE YOU HAVE IT APART, TAKE A VISUAL INVENTORY OF YOUR INNER FAIRING.
SECURING ANY LOOSE WIRES OR LOOMS WITH ZIP TIES.
1. CHOOSE A LOCATION FOR THE LINK CABLE COUPLER AND MOUNT IT WHERE IT CAN BE
ACCESSED WITH THE FAIRING COVER IN PLACE. CONNECT THE SUPPLIED FLAT LINK CABLE
FROM THE BACK-SIDE OF THE COUPLER TO THE FIRST (OR ONLY) AMPLIFIER IN PORT.
2. MULTIPLE AMPLIFIER CONFIGURATIONS: CONNECT YOUR AMPLIFIERS TOGETHER USING THE
SUPPLIED FLAT LINK CABLES IN THE ORDER IN WHICH YOU WANT THE AMPLIFIERS TO BE
SELECTED BY THE REMOTE. NOTE THE IN AND OUT PORTS OF EACH AMPLIFIER, AND CONNECT
THEM ACCORDING TO THE DIAGRAM BELOW.
NOTE: THE ORDER OF THE AMPLIFIERS IN YOUR CONFIGURATION AND HOW THEY RELATE TO THE
DESIGNATIONS AMP1 –AMP4 AT THE REMOTE CONTROL MODULE IS ENTIRELY UP TO YOU.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 5 FREMONT, CA
U
US SE ER R G GU UI ID DE E
REMOTE CONTROL OVERVIEW
AMPLIFIER STATUS OVERVIEW
THE RC-LINK REMOTE CONTROL HAS TWO BASIC MODES OF OPERATION WHEN
CONNECTED TO THE RC-LINK PORT(S) OF YOUR AMPLIFIER(S); MONITOR AND
PROGRAM. PRESSING THE AMPLIFIER SELECT BUTTON CYCLES BETWEEN THESE
TWO MODES.
MONITOR MODE (DEFAULT POWER-UP MODE):
THE APPLICABLE AMPLIFIER LEDS WILL LIGHT UP FOR EACH AMPLIFIER
DETECTED. THE LED CORROSPONDING TO EACH AMPLIFIER DETECTED WILL
FLASH IF AN OVER-CURRENT, OVER-DRIVE (CLIPPING), OR OVER-TEMPURATURE
CONDITION OCCURS. ALL DETECTED AMPLIFIERS WILL FUNCTION NORMALLY IN
MONITOR MODE. GAIN AND FREQ LEDS WILL BE OFF.
PROGRAM MODE:
ONLY THE LED CORROSPONDING TO THE AMPLIFIER BEING PROGRAMMED WILL
LIGHT UP, LEAVING ALL OTHER AMPLIFIER STATUS LEDS OFF. EACH AMPLIFIER
NOT BEING PROGRAMMED IS ALSO ATTENUATED (MUTED), LEAVING ONLY THE
CURRENTLY SELECTED AMPLIFIER FUNCTIONING NORMALLY FOR
PROGRAMMING. THE LED CORROSPONDING TO THE AMPLIFIER BEING
PROGRAMMED WILL STILL FLASH IF AN OVER-CURRENT, OVER-DRIVE (CLIPPING)
OR OVER-TEMPURATURE CONDITION OCCURS DURING PROGRAMMING.
NOTE: ONCE THE REMOTE HAS ENTERED INTO PROGRAMMING MODE, THE ADJUSTMENT
KNOBS ON EACH AMPLIFIER DETECTED WILL BE DISABLED, REGARDLESS OF WHETHER
OR NOT ANY SETTINGS ARE CHANGED, AND WILL REMAIN DISABLED UNTIL EACH
AMPLIFIER IS RESET MANUALLY (SEE RESETTING THE AMPLIFIER(S) IN THE TEST AND
TUNE SECTION OF THIS MANUAL).
WARNING: USE ONLY HAWG WIRED PROVIDED RC-LINK CABLES AND COUPLERS. WHILE THEY RESEMBLE TYPICAL
HOUSHOLD PHONE WIRES, THEY ARE NOT. NO OTHER DEVICE OR CABLE SHOULD EVER BE CONNECTED TO THIS JACK,
AND DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.
BATTERY STATUS OVERVIEW
THE RC-LINK REMOTE CONTROL HAS A BUILT-IN BATTERY MONITOR THAT
REPORTS THE STATUS OF YOUR CHARGING SYSTEM.
BATTERY MONITOR (OPTIONAL):
WITH THE CIGARETTE LIGHTER ADAPTER CABLE CONNECTED TO THE REMOTE
CONTROL MODULE, THE BATTERY STATUS LEDS INDICATE THE CURRENT STATE OF
THE CHARGING SYSTEM. THE BATTERY STATUS MONITOR FUNCTIONS
INDEPENDENT OF THE AMPLIFIER MODES, AND IS NOT REQUIRED FOR AMPLIFIER
STATUS OR PROGRAMMING.
WARNING: USE ONLY HAWG WIRED PROVIDED CIGARETTE ADAPTER CABLES WITH THIS DEVICE. NO OTHER DEVICE OR
CABLE SHOULD EVER BE CONNECTED TO THIS JACK AS POLARITY (+/-) AND POWER JACK SIZES MAY VARY. DOING SO
COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 6 FREMONT, CA
U
US SE ER R G GU UI ID DE E
TEST AND TUNE
SETTING THE GAIN:
WITH THE REMOTE IN PROGRAMMING MODE AND THE DESIRED AMPLIFIER SELECTED, FOLLOW
THESE STEPS TO SET THE GAIN CONTROL:
1. TURN THE GAIN CONTROL ALL THE WAY DOWN ( - BUTTON).
2. SET ALL TONE (BASS, TREBLE) AND EQUALIZATION CONTROLS (BALANCE, FADE) ON THE
SOURCE UNIT TO “FLAT” OR “0”, AND TURN OFF “LOUD” OR “LOUDNESS”. IF A SEPARATE
EQUALIZER IS USED, DISABLE OR SET ALL OF ITS CONTROLS TO “FLAT” OR “0”.
3. WHILE PLAYING A STANDARD NON-MP3 CD1, SET THE SOURCE UNIT’S VOLUME CONTROL TO
75% OF MAXIMUM LEVEL.
4. SLOWLY INCREASE GAIN ( + BUTTON) UNTIL YOU HEAR A SLIGHT DISTORTION OF THE AUDIO
PLAYBACK. BACK OFF THE GAIN UNTIL THE DISTORTION GOES AWAY.
WARNING: SETTING THE GAIN TOO HIGH IN AN ATTEMPT TO GET “MORE VOLUME” CAN NOT ONLY CAUSE PREMATURE
DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR GAIN
CONTROL BEING SET OUTSIDE THE TYPICAL RANGE AS INDICATED ABOVE, CALL US TO RESOLVE THE PROBLEM.
SETTING THE CROSSOVER:
WITH THE REMOTE IN PROGRAMMING MODE AND THE DESIRED AMPLIFIER SELECTED, FOLLOW
THESE STEPS TO SET THE CROSSOVERS:
1. SET ALL TONE (BASS, TREBLE) AND EQUALIZATION CONTROLS (BALANCE, FADE) ON THE
SOURCE UNIT TO “FLAT” OR “0”, AND TURN OFF “LOUD” OR “LOUDNESS”. IF A SEPARATE
EQUALIZER IS USED, DISABLE OR SET ALL OF ITS CONTROLS TO “FLAT” OR “0”.
2. WHILE PLAYING A STANDARD NON-MP3 CD1, SET THE CROSSOVER FILTER TO THE DESIRED
FREQUENCY, KEEPING IN MIND THAT TOO MUCH BASS AT HIGH VOLUMES CAN CAUSE
PREMATURE DISTORTION AND SPEAKER FAILURE.
NOTE1: THIS IS THE PREFERRED AUDIO TESTING SOURCE METHOD, AS MP3, XM, FM, AND AM ALL HAVE SOME LEVEL OF
COMPRESSION OR DEGRADATION INVOLVED, WHICH CAN LEAD TO VARYING RESULTS. IF THE PREFERRED METHOD IS
NOT AVAILABLE, USE THE MOST COMMON PLAYBACK METHOD YOU USE WHILE RIDING.
RESETTING THE AMPLIFIER(S):
WITH THE REMOTE DISCONNECTED AND THE AMPLIFIER(S) FUNCTIONING NORMALLY, FOLLOW
THESE STEPS TO RESET THE AMPLFIER(S):
1. SET BOTH GAIN AND CROSSOVER KNOBS ON THE AMPLIFIER TO “MIN” OR “0”.
2. SLOWLY BEGIN TURNING UP THE GAIN KNOB TO MANUALLY ADJUST THE AMPLIFIER. THE
AMPLIFIER IS NOW RESET.CONTUNE TUNING THE AMPLIFIER MANUALLY (REFER TO THE
AMPLIFIER INSTALLATION GUIDE FOR MORE INFORMATION ON MANUALLY ADJUSTMENT).
NOTE: IF YOU RECONNECT THE REMOTE MODULE AFTER MANUALLY ADJUSTING THE AMPLIFIER(S), THE REMOTE
SETTINGS WILL ASSUME THE CURRENT MANUAL SETTINGS OF THE AMPLIFIER ADJUSTMENT KNOBS.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 7 FREMONT, CA
U
US SE ER R G GU UI ID DE E [ [C CO ON NT TI IN NU UE ED D] ]
CONNECTORS AND CONTROLS
PLANNING YOUR SYSTEM CONFIGURATION IS THE FIRST STEP TOWARDS HI-FI HAPPINESS, SO IT’S TIME
YOU GET FAMILIAR WITH ALL THE BELLS AND WHISTLES YOUR NEW SYSTEM HAS TO OFFER. THE TABLE
BELOW LISTS THE CONTROLS AND CONNECTORS OF THE REMOTE CONTROL MODULE FOR REFERENCE.
A
AMPLIFIER SELECTOR
E
AMPLIFIER INDICATORS
J
BATTERY STATUS INDICATORS
B
GAIN PLUS (UP)
F
CROSSOVER PLUS (UP)
K
BATTERY MONITOR JACK
C
GAIN INDICATORS
G
CROSSOVER INDICATORS
L
RC-LINK OUTPUT PORT
D
GAIN MINUS (DOWN)
H
CROSSOVER MINUS (DOWN)

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 8 FREMONT, CA
U
US SE ER R G GU UI ID DE E [ [C CO ON NT TI IN NU UE ED D] ]
CONNECTORS DEFINED
BATTERY INPUT JACK:
THIS CONNECTOR ALLOWS THE REMOTE CONTROL MODULE TO MONITOR YOUR CHARGING SYSTEM
AND PROVIDE FEEDBACK BASED ON THE VOLTAGE LEVEL. THIS CONNECTION IS OPTIONAL AND NOT
REQUIRED FOR THE CONTROL MODULE TO FUNCTION. TYPICALLY USED FOR DIAGNOSTICS ONLY.
WARNING: USE ONLY HAWG WIRED PROVIDED CABLES AND WIRING. NO OTHER DEVICE OR CABLE SHOULD EVER BE
CONNECTED TO THIS JACK. DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.
RC-LINK OUTPUT PORT:
THIS CONNECTOR PROVIDES THE INTERFACE TO THE AMPLIFIER(S) IN YOUR SYSTEM
CONFIGURATION. IT CONNECTS TO THE FIRST (OR ONLY) AMPLIFIER RC-LINK IN PORT. EACH
ADDITIONAL AMPLIFIER (IF APPLICABLE) CONNECTS IN A CHAIN LINK METHOD ACCORDING TO THE
DIAGRAM IN THE INSTALLATION SECTION OF THIS MANUAL.
WARNING: USE ONLY HAWG WIRED PROVIDED CABLES AND WIRING. NO OTHER DEVICE OR CABLE SHOULD EVER BE
CONNECTED TO THIS PORT. DOING SO COULD DAMAGE YOUR DEVICE AND VOID YOUR WARANTY.
CONTROLS DEFINED
INPUT GAIN ADJUSTMENT:
A COMMON MISCONCEPTION ABOUT GAIN ADJUSTMENT IS THAT “MORE GAIN = MORE VOLUME”.
ACTUALLY, IT’S NOT THE VOLUME THAT’S BEING INCREASED, BUT RATHER THE AMPLIFIER’S
SENSITIVITY TO THE SOURCE INPUT. BY INCREASING THE GAIN LEVEL, YOU’RE INCREASING HOW
SENSITIVE THE AMPLIFIER IS TO THE SIGNAL IT RECEIVES FROM THE SOURCE UNIT. THIS IS WHY
IT’S IMPORTANT TO SET THE GAIN PROPERLY, RATHER THAN SIMPLY TURNING THE KNOB UNTIL IT’S
REALLY LOUD.
WARNING: SETTING THE GAIN TOO HIGH IN AN ATTEMPT TO GET “MORE VOLUME” CAN NOT ONLY CAUSE PREMATURE
DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR GAIN
CONTROL BEING SET OUTSIDE THE TYPICAL RANGE AS INDICATED ABOVE, CALL US TO RESOLVE THE PROBLEM.
CROSSOVER FILTER ADJUSTMENT:
THE PURPOSE OF A CROSSOVER CIRCUIT IS TO FILTER OUT A SPECIFIC RANGE OF FREQUENCIES
FROM A SPEAKER’S INPUT TO MAXIMIZE ITS PERFORMANCE. FOR A TWEETER, THE GOAL IS TO
FILTER OUT LOW (BASS) RANGE FREQUENCIES TO MAXIMIZE THE HIGH RANGE (TREBLE) RESPONSE.
CONVERSELY, FOR A SUBWOOFER, THE GOAL IS TO FILTER OUT THE HIGH AND MID RANGE
FREQUENCIES, LEAVING ONLY LOW FREQUENCIES TO PLAY THROUGH THE WOOFER.
DEFAULT: WHEN USING ANY HAWG WIRED MID-RANGE OR TWEETER SPEAKERS, THE RECOMMEND
SETTINGS ARE HIGH PASS MODE WITH THE FREQUENCY FILTER SET AT OR ABOVE 150HZ.
WARNING: SETTING THE CROSSOVER TOO LOW IN AN ATTEMPT TO GET “MORE BASS” CAN NOT ONLY CAUSE PREMATURE
DISTORTION, BUT CAN ALSO DAMAGE YOUR SPEAKERS. IF YOUR SYSTEM CONFIGURATION RESULTS IN YOUR
CROSSOVER CONTROL BEING SET ALL THE WAY UP OR DOWN, CALL US TO RESOLVE THE PROBLEM.

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 9 FREMONT, CA
S SY YS ST TE EM M D DI IA AG GR RA AM MS S

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 10 FREMONT, CA
S
SY YS ST TE EM M D DI IA AG GR RA AM MS S [ [C CO ON NT TI IN NU UE ED D] ]

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 11 FREMONT, CA
S
SP PE EC CI IF FI IC CA AT TI IO ON NS S
RC104 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
AMPLIFIER CONTROL COUNT:............................................................................. UP TO 4 AMPLIFIERS
FREQUENCY RESPONSE: .............................................................................................. 10HZ-50KHZ
ENCLOSURE DIMENSIONS: .......................................................................2.5” W X 3.70” L X 1.10” H

RC104 RC-LINK AMPLIFIER REMOTE CONTROL MODULE INSTALLATION GUIDE
HAWG WIRED PAGE 12 FREMONT, CA
W
WA AR RR RA AN NT TY Y I IN NF FO OR RM MA AT TI IO ON N
HAWG WIRED OFFERS A LIMITED WARRANTY OF OUR PRODUCTS ON THE FOLLOWING TERMS:
• LENGTH OF WARRANTY
1 YEAR ON AUDIO SYSTEMS, ELECTRONICS, SPEAKERS, AND ACCESSORIES (RECEIPT REQUIRED).
• COVERAGE
THIS WARRANTY COVERS ONLY THE ORIGINAL PURCHASER OF A HAWG WIRED PRODUCT PURCHASED FROM AN AUTHORIZED
HAWG WIRED DEALER IN THE UNITED STATES. IN ORDER TO RECEIVE SERVICE, THE PURCHASER MUST PROVIDE HAWG WIRED
WITH A COPY OF THE RECEIPT STATING THE C USTOMER NAME, DEALER NAME, PRODUCT PURCHASED AND DATE OF
PURCHASE.
• DEFECTIVE PRODUCTS
PRODUCTS FOUND TO BE DEFECTIVE DURING THE WARRANTY PERIOD WILL BE REPAIRED OR REPLACED (WITH A PRODUCT
DEEMED TO BE EQUIVALENT) AT HAWG WIRED'S DISCRETION.
• WHAT IS NOT COVERED
DAMAGE CAUSED BY ACCIDENT, ABUSE, IMPROPER OPERATIONS, WATER, THEFT
ANY COST OR EXPENSE RELATED TO THE REMOVAL OR REINSTALLATION OF PRODUCT
SERVICE PERFORMED BY ANYONE OTHER THAN AN AUTHORIZED HAWG WIRED SERVICE CENTER
ANY PRODUCT WITH THE SERIAL NUMBER OR TAMPER LABELS DEFACED, ALTERED, OR REMOVED
SUBSEQUENT DAMAGE TO OTHER COMPONENTS
ANY PRODUCT PURCHASED OUTSIDE THE U.S.
ANY PRODUCT NOT PURCHASED FROM AN AUTHORIZED HAWG WIRED DEALER
• LIMIT ON IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES INCLUDING WARRANTIES OF FITNESS FOR USE AND MERCHANTABILITY ARE LIMITED IN DURATION
TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH
OF AN IMPLIED WARRANTY, SO THIS LIMITATION MAY NOT APPLY. NO PERSON IS AUTHORIZED TO ASSUME FOR HAWG WIRED
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT.
• HOW TO OBTAIN SERVICE
PLEASE CALL 510.656.2999 FOR HAWG WIRED CUSTOMER SERVICE. YOU MUST OBTAIN A RETURN MATERIAL
AUTHORIZATION NUMBER (RMA) TO RETURN ANY PRODUCT TO HAWG WIRED. YOU ARE RESPONSIBLE FOR SHIPPING
CHARGES OF RETURNED PRODUCTS TO HAWG WIRED.
• MADE IN THE USA
OUR PRODUCTS ARE PROUDLY DESIGNED, DEVELOPED AND BUILT IN THE USA*. THE MAJORITY OF THE COMPONENTS USED
IN THE CONSTRUCTION OF OUR PRODUCTS ARE PRODUCED BY AMERICAN COMPANIES. HOWEVER, DUE TO THE GLOBAL
NATURE OF MODERN MANUFACTURING AND THE ELECTRONICS INDUSTRY IN GENERAL, SOME PARTS MAY BE MANUFACTURED
IN OTHER COUNTRIES.
*OUR SPEAKERS ARE PROUDLY DESIGNED AND DEVELOPED IN THE USA. HOWEVER, DUE TO THE GLOBAL NATURE OF LOUDSPEAKER
MANUFACTURING, OUR SPEAKERS ARE MANUFACTURED IN OTHER COUNTRIES.
H
HA AW WG G W WI IR RE ED D, , I IN NC C. .
C
CO ON NT TA AC CT T U US S B BY Y E EM MA AI IL L
SALES AND MARKETING –[email protected]
TECHNICAL SUPPORT –[email protected]
C
CO ON NT TA AC CT T U US S B BY Y P PH HO ON NE E
MAIN 510.656.2999
EFAX 510.217.6994
VISIT US ON THE WEB AT HAWG-WIRED.COM
COPYRIGHT © 2015 HAWG WIRED, INC. ALL RIGHTS RESERVED.
REV.1A PRINTED IN THE U.S.A.