TURBO RACING 91805G-VT User manual

Congratulations on your purchase of Turbo Racing 91805G-VT 4-Channel Radio
System. Designed using advanced wireless technology, Turbo Racing 91805G-VT
will advance and simplify control of your suface model and minimize interference
while providing many years of enjoyment.
This product is not a toy! (14+) Recommended for ages 14 and up.
Adult supervision required for ages under 18 years old. Contains small
parts, keep out of reach of children 3 years of age and younger.
MADE IN CHINA
www.turboracinghobby.com
Please read this manual carefully prior to using.We are not
responsible for any intentional damage or improper use.lf
you require any additional information or have any quesions
adout he product or its use,please contact us via
www.turboracinghobby.com
INSTRUCTIONS MANUAL
91805G-VT
AA x4
155.10
4CH
193.70
81.30
Turbo Racing 91805G-VT 4-Channel Radio System is warranted to the original purchaser for 30 days
from the date of purchase, verified by the sales receipt, againsr defects in material and workmanship.
Product that has been mishandled, abused, used incorrectly, used for an application other than intended
or damaged by the user is not covered under warranty. Turbo Racing. is not liable for any loss or
damage, whether direct or indirect, incidental or consequential, or from any special situatuon, arising
from the use, misuse, or abuse of this product.
91805G-VT
AUX 3 2 1

1. Steering Wheel: Controls left / right motion (note that
left-hand use (see full online manual for details).
2. Throttle Trigger: Controls forward / reverse / brake
3. Hand Grip: For holding the transmitter.
4. Antenna: Transmits signal to the receiver located in the
vehicle.
5. Power switch: Turns the transmitter ON / OFF.
6. Disassemble key：Handle is removable.
7. CH3-EPA+/-
Please put CH4 in the middle of before you press the
CH3 EPA+/-,then press EPA+/-, you can adjust the angle of ST
8. CH4-EPA+/-
Battery compartment: Houses [4] AA batteries9.
10. Channel 3 key.
Channel 4 key.
11. Multifunction Red Indicator LED:
12. REV:
(1). Please turn the wheel to left or right with Max angle , and
press REV for 2 seconds,you can hear “DI DI”, then ST will
be reverse
13. ST DR/ST TRIM: Please turn the wheel to left or right with
Max angle, and press ST-TRIM+ or ST-TRIM-, then adjust
the angle of ST
14.
15.
TH DR/TH TRIM: Please pull the throttle or push the throttle
to Max position, and press TH-TRIM+ or TH-TRIM-, then
adjust the angle of TH
Disassemble Handle & Install
INSTRUCTIONS MANUAL
www.turboracinghobby.com
(2). Please pull the throttle or push the throttle to Max position ,
and press REC for 2 seconds, you can hear “DI DI”,then REV
will be reverse
(3). Please press CH3 and REV together for 2 seconds, you can
hear “DI DI”, then REV will be reverse
1.Press the button
2.take away the handle
3.press the button, install the handle
13
14
15
Please put the CH4 switch on left or right, then press
the EPA+/- and adjust the angle
When you adjust TRIM +/-, you can sound “Di”, when the trim
is on centre, you can sound “Di-Di”; when the sound is stopped ,
then means TRIM is Max/Min
When you adjust DR +/-, you can sound “Di”, when the sound
is stopped, then means DR is Max/Min
(4). Please press REV for 2s, then turn on the gyro, and press the
REV for 2s again, then turn off the gyro

Pairing The Transmitter & Receiver
CAUTION: NEVER CONNECT A BATTERY WITH VOLTAGE
HIGHER THAN 8.0V TO THE RECEIVER, DOING SO COULD
DAMAGE THE ELECTRONICS.
INSTRUCTIONS MANUAL
www.turboracinghobby.com
Connection
•Channel 1: Controlled by the wheel, connect to a servo
for steering.
•Channel 2: Controlled by the trigger, connect to the
ESC or a servo for throttle/brake.
•Channel 3: Controlled by the adjustment knob
(0-100%) for optional use. This port can also be used
to connect a transponder device used in racing.
•AUX (Channel 4): Controlled by button (ON/OFF) for
optional use. This port is most commonly used for LED
light kits. Use this port to connect an external battery
for use with gas powered vehicles.
Battery Installation
Using the AA batteries or NIMH batteries, when the voltage
is lower than 4.5V ±0.2, the buzzer sounds continuously,
and the LED should start flashing.
1. Remove the battery cover
from the transmitter.
2. Insert four new AA batteries
according to the polarity
markings on the battery holder.
3. Reinstall the battery cover.
WARNING: DO NOT ATTEMPT TO CHARGE NON-RECHARGEABLE
BATTERIES, YOU MAY CAUSE AN EXPLOSION.
WARNING: PLEASE DON'T RESERVE THE BATTERY,OR IT WILL
BURN OUT THE PCB
Receiver Installation & Connection
Installation
To achieve full operating range with your radio system it
is critical that the receiver antenna be undamaged and
installed properly. It should be installed with as much of
the antenna as possible in a vertical position. The end of
the antenna should be contained inside an antenna tube.
When installing:
•Ensure there are no kinks in the antenna or antenna
tube.
•Never fold the end of the antenna over the tube, this
will reduce the operating range of the system and
damage the antenna.
•Ensure the receiver is mounted securely or padded
against hard impacts.
AUX 3 2 1
Receiver
1. Turn on the receiver power. Press the SW switch.The receiver’s LED should start flashing.
2. Turn on the transmitter.
3. When the LED on the receiver becomes solid,the binding process is completed.
Note: Radio systems installer in RTRs have already been bound. Only when installing a new transmitter or receiver is the
above process necessary
AUX 3 2 1
AUX 3 2 1
LED
CH1
CH2
CH3
CH4
Throttle Servo
Channel 3 Servo
Channel 4 Servo
connect to
receiver battery
Y-line

Fault Handing
INSTRUCTIONS MANUAL
www.turboracinghobby.com
Operation
Using Caution While Operating
Fail safe function setting
Safety Precautions
General Care
1. Always use clean, dry cloth or soft bristle brush to clean your equipment.
2. Never use chemical cleansers, as these could damage the sensitive electronics and plastics.
Please turn on the TX, then pull the TH trigger anywhere you want to and hold it, press the SW button
of the receiver about 2sec,the LED should start flashing for 5sec,then release SW button and
TH trigger, turn off the TX.
When there is no backward function and can’t find centre bit, please check the TRIM on centre or not.
A. THROTTLE TRIGGER B. STEERING WHEEL
1. Push the trigger
forward to slow down
or brake.
2. Pull the trigger backward
to accelerate.