Hawkeye Mfg H.264DVR User manual

Wall Mount
VERSION: 1.10

WARNING
Unauthorized reproduction of all or part of this manual is strictly prohibited.
The figures in this manual are for illustration purposes only (may differ from the actual product).
The specifications and design of the product are subject to change without prior notice for purposes of quality
improvement.
CAUTIONS
To get the best use out of the product, be sure to read the cautions before using the product. For safety, please
take note of the following:
Instructions before using the product
1. To prevent electric shock when installing, moving, or opening the DVR and peripheral devices, connect and
disconnect the cables as instructed. All cables must be connected to grounded power outlets.
2. If the product is installed near a power outlet, make sure it can be unplugged easily.
3. Do not use the DVR in water or in wet places.
4. Keep the plastic packing materials used for the DVR or other peripheral devices out of reach of children
(may cause suffocation).
Installation Environment of the DVR
1. Maintain the following conditions: operating temperature of 5˚C ~ 40˚C; operating humidity of 10% ~ 80%.
2. Install the DVR in a safe place that is free from external vibration.
3. Install the DVR in a well-ventilated place.
4. To protect the hard disk from data loss and breakdown, install the DVR away from magnetic materials.
5. When using a rack other than the standard one, use a separate table with sufficient spacing, i.e., 60cm from
the floor, 50cm from the ceiling, and 20cm from the side and back walls and other objects.
Safety Notes on the DVR
1. When installing additional boards and HDD, separate the power cable and turn OFF power supplied to the
DVR completely
2. Keep the product away from heat-generating devices such as heaters.
3. Do not use a damaged power cord.
4. To prevent problems due to magnetic interference and electric surge, use only grounded cables and power outlets.
5. If the power cord is connected, do not touch the power unit (if the power cord is connected, electric current is
still flowing internally even after the switch is turned OFF).
6. Do not place a heavy object on top of the product.
7. Do not drop a conductive object in the ventilation holes.
8. Allot sufficient space for system cabling.
9. Use only the parts indicated in the manual. Do not disassemble, repair, or modify the product without permission.
10. Incorrect system setup may cause malfunction.
11. Shut down the system normally as instructed in the manual.
1

3
3
4
8
9
Table of contents
Chapter 1 Panel Introduction
8
9
9
8
3
5
5
1.1 Description of front panel
1.2 Description of button
1.3 Hard Disk Drive installation
1.4 Connection instructions
1.5 Alarm connection instructions
2.1 Power on
2.2 Power off
2.3 Live preview
2.4 Menu
2.5 System setup
2.6 Recording setup
Chapter 2 Instruction of GUI
8
11
10
12
12
13
13
14
15
15
12
10
2.7 Recording start and stop
2.8 Recording search, playback and backup
2.9 Motion setup
2.10 Alarm setup
2.11 Network setup
2.12 Email setup
2.13 HDD management
2.14 PTZ setup
2.15 User setup
2.16 User shift
2.17 Instruction of CMS
2
6
1.6 Remote controller
7
1.7 USB mouse operations

Chapter 1 Panel Introduction
Button panel(4-ch)
Button panel(8-ch)
Button panel(16-ch)
1 2
3 9 8 6
2
1
4
510
2
11
11
10
56893
1110
98653
1
7
C
D
B
A
A: Remote controller receiver
B: USB port
C: LCD screen
D: Screen ON/OFF switch
1. Video Input 2. Video CVBS output 3. RS-485,alarm and IR receiver port
4. Spot Output 5. Network Port(RJ45) 6. USB Port 7. YPbPr Port
8. Audio Output 9. Audio Input 10. VGA Output 11. Power Input(DC12V)
3
WALL MOUNT DVR
1.1 Description of front panel
1.2 Description of button
Version 1.10

Chapter 1 Panel Introduction
4
1.3 Hard Disk Drive Installation
1 Disconnect the power cable.
2. Turn the DVR over and open the
cover bracket.
.
3. Mount the HDD properly on the
bracket.
4. Connect the SATA data and power
cable from Hdd to DVR.
5. Put the cover bracket with HDD back
with screws
Note: 1. DVR can mount 1pcs HDD up to 2TB.
2. Only 3.5'’SATA HDD can be installed.
WALL MOUNT DVR Version 1.10

Camera01 Camera16
VGA output
YPbPr output
(1920 1080)
USB port
CH9 CH11
CH7CH5
Network user
PTZ
SPOT
Network user Network user
Video input Video output
Audio input
Audio output
Power port
1) 1-4 is alarm input. "NC/NO/COM" is relay output.
NC: OFF, NO: ON, COM: common port
2) " " : Is ground cable.
alarm input
alarm output
PTZ
5
1.4 Connection Instructions
1.5 Alarm Connection Instructions
WALL MOUNT DVR Version 1.10

2
1Power key Press it to power off the DVR.
IR ID key Press it to control the DVR which have been set the remote ID.
Name Description
Symbol
No.
1. Installing the remote control
Open the battery cover, install two batteries (Type No.7), make sure positive and negative poles are
right, then close the battery cover.
2. Using the remote control
Before using it, please confirm that batteries have been installed correctly. When using it, please aim
IR TX (transmitter) of the remote control at IR reception of the DVR. Then the IR light in the front panel
will on and the icon on the top-right of the monitor screen t urns to blue " " The DVR can be
s
controlled by the remote control.
Note: If you don't want to use the remote control, you could set in the system setup menu.
Set the item REMOTE ID as OFF. Then the IR Receiver light in the front panel will be off and the operation
of the remote control is invalid and the red icon” “ displays on screen.
3. Trouble shooting
If the DVR can not be controlled by the remote control, please check the following aspects:
i Check the positive and negative poles of the batteries.
ii Check the electric quantity of the batteries.
iii Check that whether Remote Sensor are blocked or not.
iiii Whether Fluorescent lamps are being used or not nearby.
6
1.6 Remote Controller
WALL MOUNT DVR Version 1.10

3
4
5
SEQ
SPOT
PTZ
AUTO
Z+/Z-
F+/F-
I+/I-
CRUISE
FOPEN
FCLOSE
Name Description
Symbol
No.
SEQ key
Spot key
PTZ key
AUTO key
Zoom+/-
Focus+/-
Iris+/-
Info key
4ch split
9ch split
16ch split Press it to 16ch split.
Press it one time to display the status bar on the top right of screen. Press it twice.
to check the systems' information. Press it three times to check the log list.
Press it to 4ch split.
Press it to 9ch split.
Press it to shift channels automatically.
Press it to make Spot setup.
Press it to control the speed dome.
Press it to make speed dome rotate automatically.
Press it to make zoom+/-.
Press it to make focus+/-.
Press it to make iris+/-.
No Function For future use
7
USB mouse can be used. Hot swap for mouse is supported. Move the mouse cursor onto the mouse
icon to see the name. Please insert the USB mouse into the USB port of the rear panel.
1 Select or cancel " " in the item.
2 Input password in user log in interface.
4 In split-screen mode, click one of the channels to make it full screen.
Click it again to return to split-screen. Switch single channel screens.
5 Switch single channel screens.
1 In live or playback mode, it could swich the single channel image.
2 In menu mode, it could modify the data.
3 To pop up the mouse tool icons
1 Move the cursor.
2 Move the cursor to the bottom of the screen to pop up the mouse
tool bar. Move the cursor onto the icon to show the name.
1 To select shield area in "Camera setup".
2 To select motion detection area in "Motion alarm".
To change the value or digital in menu mode.
left click
Right click
Move
Drag
Wheel
1.7 USB mouse operations
WALL MOUNT DVR Version 1.10

2.2 System setup
Select "SYSTEM" in main menu to enter into SYSTEM SETUP interface.
1) Time setup: T o change system time.
2) Video format: To select PAL or NTSC format After the
operation finished, the DVR will restart automatically.
3) IR ID: To set the remote ID NO. for the relevant DVR.
4) Call monitor alarm popup: If set it on, it will popup the
picture in call monitor once there is alarm signal in any
channel.
5) Main monitor alarm popup: If set it on, it will popup
the picture in main monitor once there is alarm signal
in any channel.
6) HD output: To select HD output mode: VGA(1280*1024). YPbPr,HDMI(1920*1080).
7) Mouse display: To select CVBS or HD monitor .
8) Default load: To restore the DVR to factory default. Once finish this operation, DVR will restart automatically .
2010/09/07 10:19
U.S.(MM_DD _YY YY)
TOP MID
GREEN
PAL
ON
OFF
OFF
0
VGA(1280 102 4)
HD SCRE EN
ENGLISH
SAVESAVE EXITEXIT
DEFAULT LOADDEFAULT LOAD
SYSTEM SETUPSYSTEM SETUP
SYSTEM SETUP
TIME FORMAT
TIME DISP POS
BORDER DISP
VIDEO FORMAT
REMOTE ID
ALARM SPOT POPUP
ALARM MAIN POPUP
OSD TRANSPARENCY
HD OUTPUT
MOUSE DISPLAY
OSD LANGUAGE
2.3 Recording setup
Before recording, please make sure all the devices power on and there must have video input. Also please test
the audio input.
Press the [INFO] key in front panel twice to enter the interface of system information. Pleae check the HDD
remaining capacity. If the remaining capacity is not enough. Please change t new one or set the HDD to overwrite
If it is possible, you could enter MAIN MENU and select RECORDING SETUP to modify its setup.
01 HI G H 2 5 35 2 2 88
02 352 288 HIGH 25
03 352 288 HIGH 25
04 352 288 HIGH 25
05 352 288 HIGH 25
06 352 288 HIGH 25
07 352 288 HIGH 25
08 352 288 HIGH 25
CAMERACAMERA
09 3 5 2 288 H I GH 2 5
10 352 288 HIGH 25
11 352 288 HIGH 25
12 352 288 HIGH 25
13 352 288 HIGH 25
14 352 288 HIGH 25
15 352 288 HIGH 25
16 352 288 HIGH 25
SAVESAVE EXITEXIT
RECORD SETUPRECORD SETUP RECORD SETUPRECORD SETUP
SAVESAVE EXITEXIT
RESOLUTIONRESOLUTION QUALITYQUALITY FRAMEFRAME AUDIOAUDIO CAMERACAMERA RESOLUTIONRESOLUTION QUALITYQUALITY FRAMEFRAME AUDIOAUDIO
mode.
8
2.1 Power on
Please make sure that if the system connection is correct.
Please make sure the system format of DVR is the same as monitor's format.
Please plug the power cable in DVR.
When DVR power on, the power indicator light will turn to red.
Chapter 2 Instruction of GUI
WALL MOUNT DVR Version 1.10

2.4 Power off
Power off normally: Stop all the operation and back to preview status. Press the power key “ “
on remote control It will show the bar to confirm the operation. Press CONFIRM to finish it.
Un-normal power off: Please avoid all the un-normal power off. Such as cutting the power by removing the
power plug from DVR.
Recover after power failure: If the DVR is under recording status, and then there is a power failure. It will sa ve
all the recorded file when you restart the DVR. Also the DVR will start recording automatically .
2.5 Live preview
When you start DVR normally, you will enter live preview interfacee. And then there are some icons displayed
in the pictures. Please learn their meaning from the following table.
M
S
L
I
?L
S
L
T
No video input and recording
Symbol Color Icon Descriptions Symbol Color Icon Descriptions
Red M Under motion recording Red S Under alarm recording
Red L Under timing recording
Video loss during recording Red T
Green I Waiting for event to activate
recording Green L Video loss during waiting recording
Yellow ? Have video input but no recording Yellow L
2.6 Menu
Press the[MENU] key in front panel or click the mouse tool bar
" " to enter into main menu. And press [ESC] to exit from
main menu.
If you want to modify the information in submenu, you could use
remote control or mouse change it. When you modified the
information, please click "SAVE” to save the operation and exit
sub-menu.
Press the right key of mouse to display mouse tool bar.
9
1) Resolution: CIF resolution:352x288(PAL) 352x240(NTSC) D1 resolution: 720x576(PAL 720x480(NTSC)
When change the resolution between CIF and D1, DVR will restart automatically.
WALL MOUNT DVR Version 1.10

2) Image quality: To set the image quality at high, middle and low
.
3) Frame rate: To modify the frame rate per second.
4) Audio: To set audio recording on and off. It only support 4ch audio maximum
Please enter DISK MANAGEMENT to check the HDD information. Enter SCHEDULE SETUP to set recording
mode and time segment.
1) Channel: To select the channel to set schedule.
2) Date: To set time schedule for recording. There are 4
time segments you could set in 1 day.
3) Time segment: To set recording time from begining
to end.
2.7 Recording start and stop
Start recording: Press the [ ]key in front panel or use mouse to click the icon" "in mouse tool bar to start
recording. Once start recording or HDD begin to write, the HDD indicate light will turn on.
Press the[ ] key in front panel or use mouse to click the icon" "to stop recording.
00 0 0
08 00
18 00
00 00
08 00
18 00
24 00
00 00
00 00
00 00
00 00
00 00
24 00
00 00
00 00
00 00
TI ME
TIME
TIME
TIME
ALL CAM
ALL DAY
CAMERA
DAY
AL L
AL L
SEGMENT1
SEGMENT2
SEGMENT3
SEGMENT4
START TIME END TIME
SCHEDULE SETUP
SAVE EXIT
ALARM TYPE
2.8 Recording search, playback and backup
Press the[ ]key in front panel to enter recording search interface. You could search for the recording file and
backup the file into another devices. Also you could search for a video file to play back.
1) Valid time: From beginning to end of recording.
01 02 03 04
2010/10/10
2010/09/30
2010/10/10
USB
09 : 55 10 55
001122334455667788991010 1111 1212 1313 1414 1515 1616 1717 1818 1919 2020 2121 2222 2323
11
22
33
44
M
02
CH
BACKUPBACKUP PLAYPLAY EXITEXITCALCULATECALCULATE
VALID TIME
BACKUP DEVICE
DATE
START TIME
SEARCH MENUSEARCH MENU
TO
SIZE
END TIME
CH CH CH
10
WALL MOUNT DVR Version 1.10

2) Select the channels to playback. There are some choice for playback. You could select 1 channel, 2 channels, 3
channels,4channels to playback here. And if you want playback 8ch and 16ch together, you could press the
" " " " key in front panel.
3) Backup devices: Our DVR support DVD-RW and USB disk backup. And the DVD disk capacity should not
exceed 1.5G.
4) Playback: Select the time segment you want to playback. Modify the begining time and end time. Then click
the "PLAY" to playback. Or you could use mouse to move the icon " " to select beginning time and move icon
" " to select ending time. Finally click "PLAY" for playback.
5) Calculate: To calculate the video files capacity which you want to backup. Before you backup, please try to
proceed this operation.
6) Backup: Before backup, please make sure if the backup devices are ready, for example, USB disk and DVD-RW.
According to your need, you could select the channel name you want to backup. Then select the time segment in
this channel. Finally please click BACKUP to confirm the operation. It will take several minutes. A confirmation
message will show up after backup is finished and then move backup devices from DVR.
7) During backup, it will display some icons to show you
playback status.
2.9 Motion setup
Enter Motion setup to proceed this operation.
1) Channel: Select the chaannels you need to set motion.
2) Sensitivity: Select number 1-10 for motion sensitivity.
Generally speaking, number higher, the
sensitivity better.
LEFT
RIGHT
TOP
BOTTOM
CAMERA
DETECT AREA SETUPDETECT AREA SETUP
MOTION SETUPMOTION SETUP
01 5
335
015
230
SENSITIVITY
SAVESAVE EXITEXIT
06
CAMERA 01
3) Detection area: Select the motion detect area. Use the mouse to select the area. When it detect there is motion
in this area, the boarder colour will turn red.
11
WALL MOUNT DVR Version 1.10

2.10 Alarm setup
Enter alarm setup to proceed this operation.
The type of alarm popup: video loss alarm, motion detection alarm, external alarm.
Alarm mode: buzzer, relay, email.
2.11 Network setup
Enter Network setup to proceed the operation.
1) IP distribution: There are two type of IP, fixed IP and dynamic IP. When you click DHCP/DDNS, it will get the IP
01
02
03
04
05
06
07
08
BUZZER RELAY E-MAIL
CAMERACAMERA
ALARM SETUPALARM SETUP
09
10
11
12
13
14
15
16
31
ALARM SETUPALARM SETUP
BUZZER RELAY E-MAIL
LOSSLOSS MOTIONMOTION SENSORSENSOR CAMERACAMERA LOSSLOSS MOTIONMOTION SENSORSENSOR
SAVESAVE EXITEXIT SAVESAVE EXITEXIT
TESTTEST SAVESAVE EXITEXIT
TIME INTERVAL
E-MAIL SERVER ADDRESS
E-MAIL SERVER PORT
USERNAME
PASSWORD
PASSWORD CONFIRMATION
RECIPIENT ADDRESS
10
smtp.163.com
0025
dvrmail
**********
**********
******@163.com
E-MAIL SETUPE-MAIL SETUP
Min
2.12 Email setup
Enter Network setup and click Email to proceed this operation.
1) Time interval: To set the time interval for sending email. It
should be in denomination of minutes.
2) Email server name: To set the email server for sending email.
3) Email server port: To set the email server port.
4) User name: It's the email user name.
5) User password: It's the email password.
6) Password confirmation: To confirm your email password.
7) Receiving address: It's the email address.
DHC P / D D N S
19 2 16 8 001 1 08
19 2 16 8 001 0 01
25 5 25 5 255 0 00
20 2 09 6 134 1 33
20 2 09 6 128 1 66
68 02
00 80
IP ALLOCATION
IP ADDRESS
GATEWAY
SUBNET MASK
DNS1
DNS2
DVR PORT
IE PORT
NETWORK SETTINGNETWORK SETTING
SAVESAVE EXITEXITEMAILEMAIL
automatically. Gateway and subnet mask cannot be changed.
If the IP is 000.000.000, it means it failed to get IP automatically
Then you should check if you set the network and router.
2) DVR port: The default port is 6802 and it's changeable for users.
3) IE port: The default port is 0080 and it's changeable for users.
12
WALL MOUNT DVR Version 1.10

2.13 HDD management
Enter Disk management to proceed this operation.
1) Overwrite: Select it to overwrite recorded video automatically when the HDD is full. If you didn’t select it, if will
stop recording when HDD is full. And system will remind you to select this function or format HDD if you want
to continue recording.
2) Disk name: To check the disk information when you
connect several HDD or USB disk.
3) Disk capacity: To show capacity of the HDD.
4) Remaining capacity: To show the remaining capacity
of the HDD.
5) Bad area: To show the bad area capacity of the HDD.
6) Format: To delete all the recorded files.
2.14 PTZ setup
Set the ID of speed dome correctly.
Make sure if the AB connector of speed dome is connected well with DVR's
Enter PTZ setup to proceed this operation:
A
931%
073
000
OVERWRITE
DISK NAME
DISK CAPACITY
REMAIN CAPACITY
BAD AREA
DISK A
931G
073%
000G
SAVESAVE EXITEXIT
FORMATFORMAT
DISK MANAGEMENT
1) Channel: To select the channel connected with speed dome.
2) Baud rate: To select the baud rate of the speed dome, 1200,
2400,4800 and 9600.
3) Device ID: Default ID is the channel name.
4) Protocol: To select the communication protocol of speed
dome, PELCO_PELCO_D1 and PELCO_D2.
After speed dome setup, please enter PTZ setup. Press the [PTZ] key to enter it. Then it will display
"PTZ:CAM01 SPEED: 16 DATA: 00" in the screen. It means DVR is under PTZ status now. Press[PTZ] or [ESC]
again to exit PTZ interface. When DVR is under PTZ status, it will display the mouse tool bar as below:
01
960 0
01
PEL CO_D 2
SAVESAVE EXITEXIT
PTZ SETUPPTZ SETUP
CAMERA01
9600
01
PELCO_D2
CAMERA
BAUDRATE
DEVICE ID
PROTOCOL
13
WALL MOUNT DVR Version 1.10

To make preset setup
Descriptions
Direction key, to move speed dome
up,down, right and left
Zoom key
Icon DescriptionsIcon
To make speed dome rotate automatically.
Press it again to stop rotating.
Shut off PTZ and exit PTZ interface
To check the preset data already saved.
Modify parameters:
You could use mouse or remote control the modify the preset data. Select the item which you want to modify by
press [SPOT] key on remote control or click the item directly by mouse. Then modify the data by pressing [ ]
[SEQ]on remote control or left/right click by mouse.
Preset setup:
1) Select image point in selected camera by [ ] [ ] [ ] [ ] key. Set a number for the image point in DATA,
such as 01. Then press [ ] key on remote controller, click “ “ icon to finish the setup.
2) To view of image point which has been saved, you could select the corresponding number in DATA. Then press
[ ]key on remote control or click" "icon by mouse.
2.15 User setup
Before enter USER SETUP interface, you should enter USER LOGIN interface and type the correct password first.
1) User name: To select administrator and users. There are 4 user names ADMIN0, USER01, USER02 and USER03.
ADMIN0 is default one.
2) Password: To set user's password. The default password is 000000 for ADMIN0, 111111 for USER01,
222222 for USER02 and 333333 for USER03. Those passwords can be changed by users.
3) Authority setup: As adminstrater, you could enter USER SETUP to grant normal users authority to make setup.
Unlock setup: If the DVR was locked, please click the " " on right top of screen. Then it will popup the interface
of USER LOGIN. Type the user name and password to unlock the DVR. Then the icon” “ will turn to blue” “.
USER SETUPUSER SETUP
AD MI N 0
000000
USER NAME
PASSWORD
EXITEXIT
OKOK
67 8 9
23 4 5
10C
ADMIN 0
_ _ _ _ _ _
USER LOGINUSER LOGIN
EXITEXIT
SAVESAVE
USER NAME
PASSWORD
MENU
PTZ
RECORD
RECORD STOP
SEQ
SPOT
PLAY
AUDIO
14
WALL MOUNT DVR Version 1.10

2.16 User shift
Please enter USER LOGIN interface to shift the user and type correspond password.
2.17 Instruction of CMS
You could control the DVR via CMS. If you want learn details, please refer to “client software instruction”
attached in disk.
The operation manual is for reference only. Products may vary.
Products are subject to update without further notice.
Please contact the customer service department for latest program and
supplimentary informaton.
Any disputes or doubts in products description are subject to our final explanation.
NOTE
15
WALL MOUNT DVR Version 1.10