hawos Easy User manual

hawos Easy
Congratulations
on purchasing
your hawos our mill!
Operating instructions

experience and/or knowledge unless they are
supervised by a person responsible for their
safety or have been instructed by such a
person in how to use the device. Children
must be under supervision to ensure that they
do not play with the device.
 Never immerse the device in water.
hawos flour mills are equipped with an overcurrent
circuit breaker that protects the motor from
excessive current consumption (e. g. if debris jams
the grindstones).
In addition to the afore mentioned overload safety
switch, the motor is also equipped with a over-
heating protection, which deactivates the mill in
the event of an overload. If this occurs, set the On/
Off switch to “Off”. Once your hawos mill has
cooled off, you can use it again.
ATTENTION:
Safety is paramount!
 Only connect your mill to a properly installed
socket with earthing contact.
 Do not use defective units.
 If the mains cord is damaged, only the
manufacturer, its customer service department
or a qualified professional may replace it.
 Only authorised hawos professionals may
perform repairs.
 Never operate your mill unattended!
 Never reach into the funnel or flour outlet
when the unit is operating – risk of injury!
 Before opening the housing, be absolutely sure
to pull the mains plug to prevent the unit from
accidentally activating – risk of injury!
 This device is not intended for use by persons
(including children) with impaired physical,
sensory or mental abilities or who lack
Funnel
Adjusting wheel
(top) fixed grindstone
(bottom) rotating
grindstone
Grinding chamber
Flour outlet
On/Off switch
2 Safety is paramount

Dear mill owner,
We are delighted that you have
decided on the flour mill from
hawos!
Your hawos will serve you well in preparing your
natural food cuisine for many years to come. Please
observe the following notes before using it for the
first time. Please carefully read through these
operating instructions to familiarise yourself with
your hawos. It will reward you with reliability and
convenience.
Proper use
The mill is conceived and designed for private
household use. The device is intended for grinding
the foods listed on page 5.
Product contents
Mill, funnel lid
Before first use
Before you use the device for the first time, please
first carefully read through the safety instructions and
operating instructions. Only in this way will you be
able to use all functions safely and reliably. Hold onto
these operating instructions for future reference. Pass
these operating instructions on to any subsequent
user of the product.
1. Mill feed
Please only use clean and dry grains. You can
determine this if the seed crackles distinctly when
you crush it against a hard surface with a spoon. Wet
grain can be crushed and then looks like an oat flake.
Consult the list “Suitable mill feed” on page 5 when
adjusting the fineness. Please only mill sweet corn for
grinding corn.
Only process mill feed with the device once.
2. Power supply
Only connect the mill to an alternating current
source. Check whether the existing mains voltage
corresponds to the voltage specified on the base
plate.
3. Location
The mill housing is made of wood. Wood is a living
material that is affected by changes in temperature
and humidity, which may cause it to crack. You can
best protect and care for the housing by not placing
the mill close to radiators and not placing it right
next to a stove (steam, moisture).
4. Setting up the mill
During use, place the flour mill on a hard, level
base (kitchen countertop). The slots on the
bottom of the device may not be obstructed so
that the motor can be ventilated.
Brief instructions
• Connect to a properly installed socket with
earthing contact
• Place the our bowl under the our outlet
• Set the neness with the adjusting wheel
• Add the our to the funnel
• Turn the device on, correct the neness as
needed
• After milling, turn the device off
• Only use the our mill for grinding food! A
table of edible mill feed is provided on page 5.
Before first use 3

4 Start-up
Start-up
Please first read the section
“Before first use” (P. 3) and the
safety notes (P. 2)!
Milling
Once connected to a power supply, your hawos mill is
ready for use.
Place a bowl under the flour outlet and adjust the
fineness as desired (figures 1-3). Then fill the funnel
with grain and turn on the mill.
Figure 1: Turn the adjusting wheel to set the
fineness.
Figure 2 + 3: Turning the adjusting wheel will lift
and lower the funnel insert.

Start-up 5
Setting the fineness
You can steplessly set the fineness of the mill feed
from coarse to fine with the adjusting wheel.
(When you turn the wheel towards “fine”, the funnel
insert will lower). When changing the setting from
coarse to fine the mill should either
- be on
- or the grinder must be empty.
The different types of grain and other mill feed differ
considerably with respect to their fat and fibre
content, endosperms etc. Our table “Suitable mill
feed” is based on this. hawos mills have undergone
extensive testing and this table was compiled
accordingly for your reference.
The finer you grind, the more probable clogging of
the grindstones becomes. Pay attention to the milling
noise: If it diminishes considerably, then the
grindstones are starting to clog. Set the adjusting
wheel to coarser.
Turn off the mill once all mill feed has been
processed.
Wheat
Rye
Spelt
Barley
Oats
Millet
Sweet corn
Durum wheat
Brown rice (not parboiled rice)
Buckwheat
Green spelt
Flax seed (mix 1:1 with wheat)
Chick peas
Green peas
Nutritional yeast
Quinoa
Amaranth
Feel free to also try foods that can be rolled and
those that can be poured that are not indicated
on the adjacent table, e. g. dry spices. Proceed
with care when trying new types and let us know
about your results: We are always delighted to
learn more. Oilseeds jam the grinder due to their
high fat content. For this reason, mix mill feed
with high fat content 1:1 with wheat or another
grain.
Suitable mill feed