Hay CPH30 series User manual

1
INSTRUCTION MANUAL
By Ronan & Erwan Bouroullec
COPENHAGUE TABLE
CPH30

2
Copenhague is a furniture series designed by Ronan
and Erwan Bouroullec designed especially for the
University of Copenhagen in 2013. In addition to a homely
and welcoming expression, functionality, durability
and ease of cleaning were important design requirements for
the university. The Bouroullec brothers approached the
task by merging design history with modern technology in an
idiom with a strong and independent appearance in
a broad and versatile series that embraces both public
and private environments.
INTRODUCTION

CARE AND MAINTENANCE CARE AND MAINTENANCE
LACQUERED OR STAINED WOOD
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• If the surface is scratched or appears matt, use
a care product especially suited to lacquered or
stained wood.
• Avoid using detergents containing silicone, as they
seal the stain in and make subsequent repairs more
difficult.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.
SOAPED WOOD
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent or soap
flakes. Remove soap residue immediately using a
clean, dry cloth.
• To remove stains, clean and scrub using a thick
solution of soap flakes that should not stay on the
wood for more than two minutes. Then remove the
remaining soap residue using a damp cloth.
• If the grain of the wood rises after cleaning, gently
sand down the wood using fine-grit sandpaper (No.
220), always going with the grain.
• If the surface is scratched or appears matt, use
a care product especially suited to soaped wood.
LINOLEUM
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent or soap
flakes. Remove soap residue immediately using a
clean, dry cloth.
• If the surface is scratched or appears matt, use a
care product especially suited to linoleum.
• Stains may be carefully removed using white spirit
(mineral spirit) or a damp nano sponge dipped in
lukewarm water or linoleum care product. Follow up
immediately with a clean, dry cloth. Never use the
nano sponge dry.
• Avoid alkaline detergents such as soft (yellow
soap, washing soda, lye and scouring powder.
LAMINATE
• Wipe with a clean cloth wrung in water or in a solu-
tion of water and a neutral detergent. Remove soap
residue immediately using a clean, dry cloth.
• Stains may be carefully removed using household
ammonia or with a clean, damp cloth or a nano
sponge wrung in warm water. Never use the nano
sponge dry. Follow up immediately with a clean,
dry cloth.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.
CAUTION
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials of
your specific product to make sure that it stays in
the best shape for as long as possible.
The information below is only intended as a
general guideline. For more information on how to
remove specific stains, please enquire where you
bought the furniture.
• Always remove stains quickly before they can do
any permanent damage to the furniture.
• Avoid placing the table in direct sunlight or near
a heat source to reduce changes. As wood is a
natural material, it will change in colour and will
patinate over time.
• When you move your furniture, make sure you lift it
rather than pulling or pushing it to avoid damaging
the floor, legs and mountings.
• Tighten up the screws after one to two months’
use and whenever required.
• Avoid improper use such as putting your feet
on the table or standing on it.
• Use coasters under damp, hot or coloured objects
to avoid permanent stains.
• Avoid partially covering the surface, for example
with tablecloths or place mats, as colour variances
may appear.
• Be careful not to scratch or damage the surface
with sharp objects.

L200 / 250 / 300 x W90 x H74 cm
L200 x W80 x H105 cm
L250300 x W120 x H74 cm
CONTENTS
PAGE 08 - 19
PAGE 22 - 33

9
Allen keyE x 12C x 12 D x 6 F x 12
A x 1 B x 4
L200/250/300 x W90 x H74 cm
L200 x W80 x H105 cm
PARTS
INSTRUCTION
MANUAL

10 11
1.
While assembling, keep the table inside the cardboard box with foam edge in order to protect
the tabletop from scratches etc. Make sure that all parts are included.
1. Place the 2 x C parts with the threads facing up and the side holes facing each other.
Insert the D part with the tapered holes facing up in the C parts’ side holes.
The instructions below show how to assemble the brackets, which appear in different
steps throughout the instruction manual. Do not assemble them before the rest of
the table, but wait until the relevant steps require their assembly.
2. Insert the E parts into the C parts and screw each of them half way in a first phase,
to make sure they both fit the D parts tapered holes.
3. Tighten the E parts completely.
2mm
NOTE ON HOW TO USE THE ASSEMBLY BRACKETS

12 13
3.
Place 1 of the D parts in the holes as indicated. Make sure that the
tapered holes are pointing upwards.
2.
Place 2 of the C parts in the holes as indicated. Make sure that the threads are
pointing upwards and that the holes are facing each other.

14 15
6.
Place 4 of the C parts in the holes as indicated. Make sure that the threads
are pointing upwards and that the holes are facing each other.
4.
Drop 2 of the E parts into in the holes as indicated and make sure to hit the D parts’
tapered holes. Gently tighten all 4 E parts little by little with the Allen key.
5.
Tighten both of the E parts completely.
Repeat steps 2 - 5 at the other end of the table.

16 17
8.
Drop 4 of the E parts into the holes as indicated and make sure that they
fit the D parts’ tapered holes. Gently tighten all E parts little by little.
7.
Place 2 of the D parts in the holes as indicated at the same time.
Make sure that the tapered holes are pointing upwards.

18 19
10.
Use a proper screwdriver to fasten part F in the remaining free holes in the frame .
9.
Tighten all E parts completely. Repeat steps 6 - 8 at the other end of the table.

20 21
11.
Turn the table over (2 persons recommended).
12.

23
A x 1
B x 4
G x 2
Allen keyE x 16C x 16 D x 8 F x 16
PARTS
250/300 X W120 X H74 CM
INSTRUCTION
MANUAL

24 25
1.
While assembling, keep the table inside the cardboard box with foam edge in order to protect
the tabletop from scratches etc. Make sure that all parts are included.
2.
Place 4 of the C parts in the holes as indicated. Make sure that the threads
are pointing upwards and that the holes are facing each other.

26 27
3.
Place 2 of the D parts in the holes as indicated. Make sure that the
tapered holes are pointing upwards.
4.
Drop 4 of the E parts into the holes as indicated and make sure they fit the E parts’
tapered holes. Gently tighten all 4 E parts little by little with the Allen key.
5.
Tighten all E parts completely. Repeat steps 2 - 5
at the other end of the table.

28 29
6.
Place 4 of the C parts in the holes as indicated. Make sure that the threads
are pointing upwards and that the holes are facing each other.
7.
Place 2 of the D parts in the holes as indicated at the same time.
Make sure that the tapered holes are pointing upwards.

30 31
8.
Drop 4 of the E parts in the holes as indicated and make sure they fit the
E parts’ tapered holes. Gently tighten all E parts little by little.
9.
Tighten all E parts completely. Repeat steps 6 - 9 at
the other end of the table.

32 33
10.
Use a proper screwdriver to fasten part F in the free holes in the frame .
11.
Turn the table over (2 persons recommended).
12.

34 35

36
Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
5 710441 206583
ITEM NO. 706307
30082017