modway EEI-1415 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 3
EEI –1415 BARSTOOL
Hardware:
Component:
A Bolt M8x50mm x 5
D Flat Washer M8 x 9
1
Chair Back x1 4 Right Front Leg x1
Thank you for purchasing the MODWAY BARSTOOL!
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the barstool, we recommend that it is assembled by two adults, on a
carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or instructions until you have checked all the components and
hardware and the furniture is fully assembled.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all pieces out of reach of small children.
2 Seat Frame x1 3 Left Front Leg x1
B Bolt M8x57mm x 4
C Spring Washer M8 x 9
F Allen Wrench x 1
E Screw M4x41mm x 6
PHILLIPS HEAD SCREW DRIVER
NOT PROVIDED
2
3
4
7
5
6
1
Left Stretcher x1 Right Stretcher x1 Front Stretcher x1
5 6 7

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 3
EEI –1415 BARSTOOL
STEP 1:
STEP 2:
Please put the Chair Back (1) upside down on a carpeted or padded area.
Then open the black fabric which is attached by Velcro from back to front on the bottom of the Seat Frame (2). The inside
of the Seat Frame(2) will now be visible.
Attach the Seat Frame (2) to the Chair Back(1) by using 1 piece of Bolt (A), 4 pieces of Bolt (B), 5 pieces of Spring
Washer (C) and 5 pieces of Flat Washer (D) as shown.
Do not fully tighten Bolts (A&B) at this step.
Insert Left Front Leg (3) into the left corner of Seat Frame (2) as shown.
Attach by 2 pieces of Bolt (A), 2 pieces of Spring Washer (C) and 2 pieces of Flat Washer (D) as shown.
Repeat the same steps for Right Front Leg (4).
Do not fully tighten Bolts (A) for either leg.
1
Ax1 Dx5 Bx4 Cx5 Hardware & Tool required
2
A
C
D
Ax4 Dx4 Cx4 Hardware & Tool required
1
2
3
4
C
D
A
B
C
D

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 3
EEI –1415 BARSTOOL
STEP 3:
STEP 4:
Assembly is completed. The barstool is ready to use now!
Carefully turn over the barstool.
Please put a heavy object or seat one adult on top of the Seat Frame (2) to pressure the chair for leveling.
Fully tighten the Bolts (A&B) with Allen Wrench (F) and Screw (E) with Phillips Head Screw Driver (Not Provided).
Ex6 Phillips Head Screw
Driver (Not Provided) Hardware & Tool required
Insert the Front Stretcher (7) into Left Front Leg (3) and Right Front Leg (4) as shown.
Secure them by using 2 pieces of Screw (E) with Phillips Head Screw Driver (Not provided).
Repeat the same steps for the remaining Left Stretcher (5) and Right Stretcher (6).
Do not fully tighten Screws (E) at this step.
5
6
7
3
4
E
Fx1 Phillips Head Screw
Driver (Not Provided) Hardware & Tool required
F