Hay COPENHAGUE TABLE User manual

1
By RONAN & ERWAN BOUROULLEC
> INSTRUCTIONS MANUAL <
H AY
COPENHAGUE TABLE
CPH30

2
> INTRODUCTION <
Copenhague is a furniture series designed by Ronan
and Erwan Bouroullec designed especially for the
University of Copenhagen in 2013. In addition to a homely
and welcoming expression, functionality, durability
and ease of cleaning were important design requirements for
the university. The Bouroullec brothers approached the
task by merging design history with modern technology in an
idiom with a strong and independent appearance in
a broad and versatile series that embraces both public
and private environments.

> CARE AND MAINTENANCE <
CAUTION
With a little care you can prolong the life of your
furniture and keep the materials in good condition.
Wood is a natural material, which may change in colour
and will patinate over time. Always remove stains quickly
before they can do any permanent damage to the
furniture.
• Avoid placing the table in direct sunlight or near a heat
source to reduce changes.
• When you move the furniture, make sure to lift it rather
than pulling or pushing it to avoid damaging the floor,
legs and mountings.
• Tighten up the screws after one to two months’ use.
• Avoid improper use such as putting your feet on the
table and standing on it.
• Use coasters under damp, hot or coloured objects to
avoid permanent stains.
• Avoid covering the surface partially, for example with
tablecloths or placemats, as colour variances may
appear.
LACQUERED OR STAINED WOOD
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent. Remove soap residue
immediately using a clean, dry cloth.
• If the surface is scratched or appears matt, use a
care product suited especially for lacquered or stained
wood.
• Avoid using detergents containing silicone, as that
would seal the stain in and make subsequent repairs
more difficult.
• Avoid using scouring cream or scouring pads, as they
may scratch the surface.
SOAPED WOOD
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent or soap flakes. Remove
soap residue immediately using a clean, dry cloth.
• To remove stains, clean and scrub using a thick
solution of soap flakes that is not allowed to stay on the
wood for more than 2 minutes. Then remove the
remaining soap residue using a damp cloth.
• If the grain of the wood rises after cleaning, gently
sand down the wood using fine-grit sandpaper (No.
220), always going with the grain.
• If the surface is scratched or appears matt, use a care
product suited especially for soaped wood.
LINOLEUM
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent or soap flakes. Remove
soap residue immediately using a clean, dry cloth.
• If the surface is scratched or appears matt, use a care
product suited especially for linoleum.
• Stains may be carefully removed using white spirit
(mineral spirit) or a damp nanosponge dipped in luke-
warm water or linoleum care. Follow up immediately
with a clean, dry cloth. Never use the nanosponge dry.
• Avoid alkaline detergents such as soft (yellow) soap,
washing soda, lye and scouring powder.
LAMINATE
• Clean with a clean cloth wrung in water or in a solution
of water and a neutral detergent. Remove soap residue
immediately using a clean, dry cloth.
• Stains may be carefully removed using household
ammonia or with a clean, damp cloth or a nanosponge
wrung in warm water. Never use the nanosponge dry.
Follow up immediately with a clean, dry cloth.
• Avoid using scouring cream or scouring pads, as they
may scratch the surface.
> CARE AND MAINTENANCE <

> CONTENTS<
PAGE 8 - 19
L200/250/300 x W90 x H74 cm
L200 x W80 x H105 cm
PAGE 20 - 31
L250/300 x W120 x H74 cm

9
A x 1 B x 4
Allen keyF x 12E x 12D x 6C x 12
> PARTS <> L200/250/300 x W90 x H74 cm • L200 x W80 x H105 cm<

10 11
1.
While assembling, keep the table inside the cardboard box with edge foam to protect the
tabletop from scratches etc. Make sure that all parts are included.
2.
Place 2 of the C parts in the shown holes. Make sure that the thread
is pointing upwards and that the holes are facing each other.

12 13
3.
Place 1 of the D parts in the shown holes. Make sure that the
tapered holes are pointing upwards.
4.
Drop 2 of the E parts in the shown holes and make sure to hit the D parts’
tapered holes. Gently tighten all 4 E parts little by little with the Allen key.
5.
Tighten both of the E parts completely.
Repeat step 2 - 5 at the other end of the table.

14 15
6.
Place 4 of the C parts in the shown holes. Make sure that the thread
is pointing upwards and that the holes are facing each other.
7.
Place 2 of the D parts in the shown holes at the same time.
Make sure that the tapered holes are pointing upwards.

16 17
8.
Drop 4 of the E parts in the shown holes and make sure to hit the
D parts’ tapered holes. Gently tighten all E parts little by little.
9.
Tighten all E parts completely. Repeat step 6 - 8 at the other end of the table.

18 19
10.
Use a proper screwdriver to fasten part F in the remaining free holes in the frame .
11.
Flip the table (2 persons recommended).
12.

21
> L200/250/300 x W120 x H74 cm<
A x 1
B x 4
C x 2
Allen keyG x 16F x 16Ex 8D x 16
> PARTS <

22 23
1.
While assembling, keep the table inside the cardboard box with edge foam to protect the
tabletop from scratches etc. Make sure that all parts are included.
2.
Place 4 of the D parts in the shown holes. Make sure that the thread
is pointing upwards and that the holes are facing each other.

24 25
3.
Place 2 of the E parts in the shown holes. Make sure that the
tapered holes are pointing upwards.
4.
Drop 4 of the F parts in the shown holes and make sure to hit the E parts’
tapered holes. Gently tighten all 4 F parts little by little with the Allen key.
5.
Tighten both all F parts completely. Repeat step 2 - 5
at the other end of the table.

26 27
6.
Place 4 of the D parts in the shown holes. Make sure that the thread
is pointing upwards and that the holes are facing each other.
7.
Place 2 of the E parts in the shown holes at the same time.
Make sure that the tapered holes are pointing upwards.

28 29
8.
Drop 4 of the F parts in the shown holes and make sure to hit the
E parts’ tapered holes. Gently tighten all F parts little by little.
9.
Tighten all F parts completely. Repeat step 6 - 9 at the other end of the table.

30 31
10.
Use a proper screwdriver to fasten part G in the remaining free holes in the frame .
11.
Flip the table (2 persons recommended).
12.

33

34 35

36
Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
H AY 5 710441 206583
ITEM NO. 706307