Hayward Phantom 6000 User manual

Important Safety Instructions
1
Use Only Genuine Hayward Replacement Parts.
Warning
Read this entire Owner’s Guide before assembling and
installing the Phantom clea ne r. Failure to follow safety
warnings and Owner’s Guide instructions can result in
severe injury, death or property damage.
For additional free copies of the Owner’s Guide you
can download them from w ww. ha yw ar dn et .com
or call [phone].
Warning - Risk of Electrical Shock
The Hayward Phantom Automatic Pool Cleaner is designed to
connect to a threaded 1-1/2 inch female pipe fitting on a
dedicated return line that is powered by a 3/4 H.P.Booster
Pump. You should have a licensed electrician install the
cleaner’s booster bump. The Booster Pump must be
installed in accordance with the National Electrical Code
and all local code requirements. Failure to do so can
result in serious injury or death.
Warning - Risk of Injury
Failure to follow the safety warnings below may result in
severe injury,death or property damage.
•Alw ays disconnect and remove the cleaner and pressure
hose before entering the pool.
• Disconnect the Safety Rope that seperates the pool’s shallow
end from the pool’s deep end, b e fore running the Phantom.
Alw ays reconnect the Safety Rope before entering the pool.
•Alw ays handle with care. Do not let children or pets play with
the cleaner; it is not a toy.
•Alw ays turn the Booster Pump O F F before handling
the cleaner.
• Do not operate outside the pool. The Phantom Cleaner
and hoses contain high-pressure water jets that may
cause injury.
• Disconnect pressure hose from the universal wall fitting
be fore removing the cleaner from the pool.
•Never point any of the cleaner’s high-pressure jets, pr es su re
ho se , pressure gauge or sweep hose at any person or pet.
Important Information
Caution - Risk of Equipment Damage
•Alw ays turn the Filtration Pump on befo re turning the
booster pump on. Running the booster pump dry will
da mage the booster pump and isnot covered by the
Hayward warranty.
•Alw ays disconnect and remove the Phantom cleaner and
hoses from the pool before cleaning or backwashing the
pool filter.
• After cleaning or backwashing the pool filter, allow the
fi lt ration system to run for a minimum of five minutes or until
all debris has been flushed from plumbing lines before
reconnecting the Phantom cleaner.
• New plumbing lines must be flushed out before connecting
the Phantom cleaner.
•The Phantom cleaner should not be used to remove plaster
dust or construction debris from new or renovated pools.
•The Phantom cleaner should not be used to remove
excessive sand (dense debris) following wind or sandstorms.
•Alw ays disconnect and remove the Phantom cleaner and
hoses before chemically shocking the pool.
•O n lyoperate the Phantom cleaner for the period of time
n e c e s s a ryto clean the pool. Excessive use is unnecessary
and will cause cleaner parts to premat u r e ly wear.
•Re gu larly inspect the cleaner and hoses; do not use if
da maged or if any rough edges are visible on the cleaner;
this can cause damage to the pool.
• Lift the Phantom cleaner by its wing (Part A, pa ge 4), never
by the hose or bag.
Discl a i m e r
• Pool plaster is affected by age, water chemistry, etc.
• Pool plaster can deteriorate over time.
•The integrity of “good” pool plaster is such that a pool
vacuum cleaner – automatic or manual – cannot remove
the plaster.
•The integrity of “good” pool plaster is such that the plaster
will cause wear on the cleaner, the cleaner will not wear out
“g oo d” pool plaster.
•V i nyl pool liners are affected by age, sunligh t, and water
chem i s try.
•V i nyl pool liners can become brittle and weak.
•V i nyl pool liners can be affected by the installation and the
po ol ’s surroundings.
•P atterns on vinyl pool liners vary in quality.
• When installing the Phantom cleaner, you assume
responsibility for the condition of the pool’s surroundings
and chemistry.

Use Only Genuine Hayward Replacement Parts.
Contents Introduction
3
Use Only Genuine Hayward Replacement Parts.
2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
For Your Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Principle Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Preparing the Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Dedicated Return Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Tools Needed for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting Phantom Cleaner to Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installing the Universal Wall Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembling and Sizing the Rigid Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting the Rigid Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Disconnecting a Hose Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting Hose to Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operating the Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Setting Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Large Capacity Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Attaching Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Removing Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Emptying Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Sand (Dense Debris) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Correctly Operating Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Spin-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Sweep Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Fine Debris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Sand (Dense Debris) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Phantom Cleaner Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Spin-Out Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Spin-Out Cam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Adjusting Spin-Out Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Top and Bottom Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Adjusting Sweep Hose Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Removing Phantom Cleaner from Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Emptying Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning the In-Line Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Sweep Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Storing the Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Periodic Freezing Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Booster Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Phantom Parts Diagram and Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . .18
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
C o n gr at u l ations on your purchase of the Hayward Phantom
A u t o m atic Pool Cleaner. The Hayward Phantom is the only Tot al
Pool Cleaner. The Phantom is designed to not only to clean your
poo l’s bottom and sides, but also to skim the wat er ’s surface as
well – all automat i c a l ly!
This revolutionary design offers the following features:
• Faster Cleaning
-Wider Vacuum Nozzle
-Powerful Sweep Hose
• Large Debris Pick-up
-Large Suction Inlet
-Three High Pressure Water Jets
•Less Frequent Bag Cleaning
-Large Capacity Bag
-Easy to remove, clean and replace debris bag
• Complete Pool Cov e r a g e
- P atented AquaDrive™ water jet propulsion
-Randomized Cleaning & Spin-out
-Sweeps debris off steps while skimming
• Cleans the Pool Bottom, Sides and Skims
the Water’s Surface
-Automatic Ascent and Descent
-Switch for Bottom & Side Cleaning Only or Surface
Skimming Only
•Less Wear on Pool Surface
-P atented AquaDrive water jet propulsion: no powered
wheels wearing pool surfaces
• Easy Installation
A limited warranty program protects your Hayward Phantom
cleaner. To take full advantage of this limited warranty,please
read, complete and return the Limited War ranty
Registration Card within 14 days of purchase date.
Your warranty card is included in this Owner’s Guide.
Imp o r t a n t
This Owner’s Guide is for Phantom owners who want to install
their A u t o m atic Pool Cleaner. However, we recommend that an
Authorized Hayward Dealer install the cleaner.
The Hayward 5060 Booster Pump purchased separat e lyor as
part of the Phantom Aut o m atic Pool Cleaner package offers
optimum cleaner perform ance. Use of other booster pumps will
provide acceptable performance if they deliver at least 35 Pounds
per Square Inch (PSI) at 12 Gallons Per Minute (GPM) at the
de di cated line pool wall fitting. For electrical and plumbing
in st allation procedures for the Hayward Booster Pump, refer to the
Ow ne r’s Guide that comes with the Hayward 5060 Booster Pump.
Purchase Date
Serial Number
(located on back of cleaner)
Number of Rigid Pipe Assemblies Used
Pressure Gauge Reading
For Your Records

Use Only Genuine Hayward Replacement Parts.
Contents Introduction
3
Use Only Genuine Hayward Replacement Parts.
2
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
For Your Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Principle Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Preparing the Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Dedicated Return Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Tools Needed for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Connecting Phantom Cleaner to Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installing the Universal Wall Fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Assembling and Sizing the Rigid Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Connecting the Rigid Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Disconnecting a Hose Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting Hose to Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Operating the Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Setting Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Large Capacity Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Attaching Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Removing Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Emptying Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Sand (Dense Debris) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Correctly Operating Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Spin-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Sweep Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Fine Debris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Sand (Dense Debris) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Pressure Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Phantom Cleaner Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Spin-Out Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Spin-Out Cam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Adjusting Spin-Out Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Changing Top and Bottom Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Adjusting Sweep Hose Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Removing Phantom Cleaner from Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Emptying Debris Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cleaning the In-Line Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Sweep Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Storing the Phantom Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Winterizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Periodic Freezing Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Booster Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Phantom Parts Diagram and Replacement Parts List . . . . . . . . . . . . . . . . . . . . . . . .18
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
C o n gr at u l ations on your purchase of the Hayward Phantom
A u t o m atic Pool Cleaner. The Hayward Phantom is the only Tot al
Pool Cleaner. The Phantom is designed to not only to clean your
poo l’s bottom and sides, but also to skim the wat er ’s surface as
well – all automat i c a l ly!
This revolutionary design offers the following features:
• Faster Cleaning
-Wider Vacuum Nozzle
-Powerful Sweep Hose
• Large Debris Pick-up
-Large Suction Inlet
-Three High Pressure Water Jets
•Less Frequent Bag Cleaning
-Large Capacity Bag
-Easy to remove, clean and replace debris bag
• Complete Pool Cov e r a g e
- P atented AquaDrive™ water jet propulsion
-Randomized Cleaning & Spin-out
-Sweeps debris off steps while skimming
• Cleans the Pool Bottom, Sides and Skims
the Water’s Surface
-Automatic Ascent and Descent
-Switch for Bottom & Side Cleaning Only or Surface
Skimming Only
•Less Wear on Pool Surface
-P atented AquaDrive water jet propulsion: no powered
wheels wearing pool surfaces
• Easy Installation
A limited warranty program protects your Hayward Phantom
cleaner. To take full advantage of this limited warranty,please
read, complete and return the Limited War ranty
Registration Card within 14 days of purchase date.
Your warranty card is included in this Owner’s Guide.
Impor t a n t
This Owner’s Guide is for Phantom owners who want to install
their A u t o m atic Pool Cleaner. However, we recommend that an
Authorized Hayward Dealer install the cleaner.
The Hayward 5060 Booster Pump purchased separat e lyor as
part of the Phantom Aut o m atic Pool Cleaner package offers
optimum cleaner perform ance. Use of other booster pumps will
provide acceptable performance if they deliver at least 35 Pounds
per Square Inch (PSI) at 12 Gallons Per Minute (GPM) at the
dedicated line pool wall fitting.For electrical and plumbing
installa tion procedures for the Hayward Booster Pump, refer to the
Owner’s Guide that comes with the Hayward 5060 Booster Pump.
Purchase Date
Serial Number
(located on back of cleaner)
Number of Rigid Pipe Assemblies Used
Pressure Gauge Reading
For Your Records

Principle Parts Preparing the Pool
4 5
Use Only Genuine Hayward Replacement Parts.
Caution - Risk of Equipment Damage
Hose may be stored folded pipe-to-pipe. Only first 3-foot hose
section and sweep hose must be stored straight, not coiled.
A. Wing
B. Large Capacity Debris Bag with Float Closure
C. Cleaner Connector
D. Sweep Hose Connector
E. Sweep Hose Adjustment Knob
F. Cam Cap
G. Rigid Pressure Hose
H. Hose Float
I.Hose Pipe Coupling
J. Hose Swivel
K. Adjustable Wall Quick Connect
L. Sweep Hose
M. Wear Roller
N. Rigid Hose Pipe
O. Universal Wall Fitting
P. Top / Auto / Bottom Switch
Q. In-Line Filter
R. Hose Swivel Assembly
S. Hose Cleaner End Assembly
T. Hose Wall End Assembly
U. Setup Pressure Gauge
The Phantom cleaner should not be used to clean the
pool for spring start-up until the following steps
have been taken:
1. Clear the pool of any objects that might interfere with the
cleaner’s operation.
2. Check to see that the water is at the recommended level.
3. Check the water chemistry.The water should be properly
balanced (ph level) and the pool free from algae.
Note: Algae can adversely affect the operation and
performance of the cleaner.
4. Clean or backwash the filtration system without the
Phantom cleaner in the pool.
Caution - Risk of Equipment Damage.
Alw ays disconnect the Phantom Cleaner and hoses form the
Universal Wall Fitting and remove from pool before backwashing
or cleaning the filtration system. Failure to do so can damage the
Booster Pump and Cleaner.
5. Clean the filtration system pump’s strainer basket
Note: After installing the Phantom cleaner, clean the
filtration system at regular intervals according to individual
pool conditions.
New Pool Construction
1. Brush newly constructed pool surface and manually
vacuum new surface debris before installing the
Phantom.
Sand (dense debris)
Always empty the Phantom bag when sand
(or heavy debris) effects the cleaner’s stability
Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
Dedicated Booster Pump Return Line
The cleaner is designed to connect to a 1-1/2 inch dedicate d
return line that is at least 6 inchesbelow the normal water level
with 1-1/2 inch female threads. If the dedicated return line has
3/4 inch female threads, you will need to purchase a 1-1/2 inch
NPTF x 3/4 inch NPTM adapter.
Tools Needed for Installation
•Flat blade screwdriver for adjusting the Regulator on the
Wall Quick Connect.
•Rigid Pressure Hose Measuring Tape
(included in Bag #1).
Wall Quick Connect
R e a rview Product
Front view Product
C
L
D
E
M
G
O
K
B
F
A
P
Rigid Pressure Hose Parts (G)
I
H
U
J
N
R
TK
Q
C
LM
S

Principle Parts Preparing the Pool
4 5
Use Only Genuine Hayward Replacement Parts.
Caution - Risk of Equipment Damage
Hose may be stored folded pipe-to-pipe. Only first 3-foot hose
section and sweep hose must be stored straight, not coiled.
A. Wing
B. Large Capacity Debris Bag with Float Closure
C. Cleaner Connector
D. Sweep Hose Connector
E. Sweep Hose Adjustment Knob
F. Cam Cap
G. Rigid Pressure Hose
H. Hose Float
I.Hose Pipe Coupling
J. Hose Swivel
K. Adjustable Wall Quick Connect
L. Sweep Hose
M. Wear Roller
N. Rigid Hose Pipe
O. Universal Wall Fitting
P. Top / Auto / Bottom Switch
Q. In-Line Filter
R. Hose Swivel Assembly
S. Hose Cleaner End Assembly
T. Hose Wall End Assembly
U. Setup Pressure Gauge
The Phantom cleaner should not be used to clean the
pool for spring start-up until the following steps
have been taken:
1. Clear the pool of any objects that might interfere with the
cleaner’s operation.
2. Check to see that the water is at the recommended level.
3. Check the water chemistry.The water should be properly
balanced (ph level) and the pool free from algae.
Note: Algae can adversely affect the operation and
performance of the cleaner.
4. Clean or backwash the filtration system without the
Phantom cleaner in the pool.
Caution - Risk of Equipment Damage.
Alw ays disconnect the Phantom Cleaner and hoses form the
Universal Wall Fitting and remove from pool before backwashing
or cleaning the filtration system. Failure to do so can damage the
Booster Pump and Cleaner.
5. Clean the filtration system pump’s strainer basket
Note: After installing the Phantom cleaner, clean the
filtration system at regular intervals according to individual
pool conditions.
New Pool Construction
1. Brush newly constructed pool surface and manually
vacuum new surface debris before installing the
Phantom.
Sand (dense debris)
Always empty the Phantom bag when sand
(or heavy debris) effects the cleaner’s stability
Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
Dedicated Booster Pump Return Line
The cleaner is designed to connect to a 1-1/2 inch dedicated
return line that is at least 6 inchesbelow the normal water level
with 1-1/2 inch female threads. If the dedicated return line has
3/4 inch female threads, you will need to purchase a 1-1/2 inch
NPTF x 3/4 inch NPTM adapter.
Tools Needed for Installation
•Flat blade screwdriver for adjusting the Regulator on the
Wall Quick Connect.
•Rigid Pressure Hose Measuring Tape
(included in Bag #1).
Wall Quick Connect
R e a rview Product
Front view Product
C
L
D
E
M
G
O
K
B
F
A
P
Rigid Pressure Hose Parts (G)
I
H
U
J
N
R
TK
Q
C
LM
S

7
Use Only Genuine Hayward Replacement Parts.Use Only Genuine Hayward Replacement Parts.
Connecting the Phantom Cleaner To Pool
6
Installing Universal Wall Fitting
Builders: Install the Dedicated Return Line at the
midpoint of the pool’s long wall.
Specificat ion:Dedicated Return Line in Pool Wall .
Depth: At least 6 inches below water level.
Size: 1-1/2 inch NPT Female Thread ed.
1. Flush plumbing lines before proceeding.
2. Turn Booster Pump and Main Filtration Pump O F F.
3. Remove plug or existing Universal Wall Fitting from
previously installed pool cleaner (if any ) .
4. Remove the Universal Wall Fitting (part O) and Teflon®t ape
from Bag #1.
5. When installing or re-installing the Universal Wall Fitting
use Te fl o n®tape on its plastic threads. L e ave two starting
threads on the end of the Universal Wall Fitting un-taped.
6. Screw the Universal Wall Fitting into the Dedicated
Return Line.
Important: Turn the Universal Wall Fitting 1 full turn to the
right to engage starting threads. Be sure both parts are
started properly (not cross threaded) then resume tightening
– hand tighten only. The Universal Wall Fitting may not screw
all the way into the Dedicated Return Line.
Do not over tighten.
Te fl on ®is a registered trademark of E.I. du Pont de Nemours
and Company.
Assembling and Sizing the Rigid Pressure Hose
Assembling and Sizing the Rigid Pressure Hose
1. Open the plastic bag labeled #1 that contains 10 Rigid Hose
Pipes (Part N) and 5 Hose Pipe Couplings (Part I).
2. Lu b r i c ate the 5 Hose Pipe Couplings by dunking them in
s o apy water.
3. Align the Barbs on the Hose Pipe Coupling with the Tabs on
the Rigid Hose Pipes and snap together. Be sure the black
o-ring does not slip out of the groove on the Hose Pipe
Coupling (if the o-ring is visible through the latch opening
when pipes are snapped together the o-ring has slipped out
of the groove and will leak)
4. Make 5 Sets of Pipe Assemblies by connecting 1 Rigi d
Hose Pipe onto each end of the Hose Pipe Couplings.
5. L o c ate the “Measuring Tape” (packed in Bag #1), secure the
end of the tape marked “Wall Connector End”on the pool
coping immediat e ly above the Universal Wall Fitting.
6. Unroll the Measuring Tape, walk around the pool to the
farthest point along the pool wall from the Universal Wall
Fitt in g.
At the farthest point from the Universal Wall Fitting hold
the Measuring Tape at the pool edge/coping and read the
number of Pipe Assemblies specified on the tap e .
Universal Wall Fitting
Rigid Hose Pipe Assembly
Dedicated Return Line
Universal Wall Fitting (O)
Measuring Ta pe
Connecting Hose Pipes
I
N
a. Note: If the measuring tape specifies more than 5 Pipe
Assemblies, you need to purchase the additional Pipe
sections (P/N AX6000HE) from your Authorized Hayward
Dealer.
b. If the measuring tape specifies fewer than 5 Pipe
Assemblies, set the remaining Pipe Assemblies aside you
won’t need them.
Rec ta ng ul ar-Shaped Po ol
Kidney-Shaped Po ol
Angle-Shaped Po ol
Universal Wall Fitting
(Dedicated Line)
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Farthest Point
Universal Wall Fitting
(Dedicated Line)
Farthest Point
I N
1 Pipe
Assembly

7
Use Only Genuine Hayward Replacement Parts.Use Only Genuine Hayward Replacement Parts.
Connecting the Phantom Cleaner To Pool
6
Installing Universal Wall Fitting
Builders: Install the Dedicated Return Line at the
midpoint of the pool’s long wall.
Specificatio n:D edicated Return Line in Pool Wall.
Depth: At least 6 inches below water level.
Size: 1-1/2 inch NPT Female Threaded .
1. Flush plumbing lines before proceeding.
2. Turn Booster Pump and Main Filtration Pump O F F.
3. Remove plug or existing Universal Wall Fitting from
previously installed pool cleaner (if any ) .
4. Remove the Universal Wall Fitting (part O) and Teflon®t ape
from Bag #1.
5. When installing or re-installing the Universal Wall Fitting
use Te fl o n®tape on its plastic threads. L e ave two starting
threads on the end of the Universal Wall Fitting un-taped.
6. Screw the Universal Wall Fitting into the Dedicated
Return Line.
Important: Turn the Universal Wall Fitting 1 full turn to the
right to engage starting threads. Be sure both parts are
started properly (not cross threaded) then resume tightening
– hand tighten only. The Universal Wall Fitting may not screw
all the way into the Dedicated Return Line.
Do not over tighten.
Te fl on ®is a registered trademark of E.I. du Pont de Nemours
and Company.
Assembling and Sizing the Rigid Pressure Hose
Assembling and Sizing the Rigid Pressure Hose
1. Open the plastic bag labeled #1 that contains 10 Rigid Hose
Pipes (Part N) and 5 Hose Pipe Couplings (Part I).
2. Lu b r i cate the 5 Hose Pipe Couplings by dunking them in
s o apy water.
3. Align the Barbs on the Hose Pipe Coupling with the Tabs on
the Rigid Hose Pipes and snap together. Be sure the black
o-ring does not slip out of the groove on the Hose Pipe
Coupling (if the o-ring is visible through the latch opening
when pipes are snapped together the o-ring has slipped out
of the groove and will leak)
4. Make 5 Sets of Pipe Assemblies by connecting 1 Rigi d
Hose Pipe onto each end of the Hose Pipe Couplings.
5. L o c ate the “Measuring Tape” (packed in Bag #1), secure the
end of the tape marked “Wall Connector End”on the pool
coping immediat e ly above the Universal Wall Fitting.
6. Unroll the Measuring Tape, walk around the pool to the
farthest point along the pool wall from the Universal Wall
Fitting.
At the farthest point from the Universal Wall Fitting hold
the Measuring Tape at the pool edge/coping and read the
number of Pipe Assemblies specified on the tap e .
Universal Wall Fitting
Rigid Hose Pipe Assembly
Dedicated Return Line
Universal Wall Fitting (O)
Measuring Ta pe
Connecting Hose Pipes
I
N
a. Note: If the measuring tape specifies more than 5 Pipe
Assemblies, you need to purchase the additional Pipe
sections (P/N AX6000HE) from your Authorized Hayward
Dealer.
b. If the measuring tape specifies fewer than 5 Pipe
Assemblies, set the remaining Pipe Assemblies aside you
won’t need them.
Rec ta ng ul ar-Shaped Po ol
Kidney-Shaped Po ol
Angle-Shaped Po ol
Universal Wall Fitting
(Dedicated Line)
Universal Wall Fitting
(Dedicated Line)
Farthest Point
Farthest Point
Universal Wall Fitting
(Dedicated Line)
Farthest Point
I N
1 Pipe
Assembly

9
Use Only Genuine Hayward Replacement Parts.
Warning - Risk of Injury
The Filtration and Booster Pumps must be OFF when connecting
or disconnecting cleaner hose.
Caution - Risk of Equipment Damage
The filter pump must alw ays be run to clear air from the system
before turning the Booster Pump ON. Never run the Booster
Pump without the main filter pump O N. Running the Booster
Pump dry will damage the Booster Pump and void the warranty.
Operating the Phantom Cleaner
1. Be sure all filtration system valves are open and supplying
water to the Booster Pump.
2. Be sure valves to and from the Booster Pump and dedicated
return line are fully opened.
3. The Phantom Cleaner and its Booster Pump can only
operate when the pool’s filter pump is operat i n g .
Caution - Risk of Equipment Damage
Failure to open valves fully and/or failure to have the filtration
system operating will damage the Booster Pump.Thisdamage
voids the Booster Pump’s warranty.
Setting Pressure
Important: The cleaner will not operate properly if the pressure
is not properly set. Too little pressure will prevent proper
movement and cleaning.Too much pressure will cause poor
cleaning and premature wear of Cleaner parts.
Warning - Risk of Injury
Be careful to hold the Cleaner Connector (Part C) with the Setup
Pressure Gauge (Part U) attached under water and not to be
sprayed by the hole in the Setup Pressure Gauge or by the
Sweep Hose. Never point a jet or hose at people or pets.
Clip the Setup Pressure Gauge to the hose near the Wall Quick
Connect.
1. Turn the filtration system pump O N then the Booster Pump
ON. Read the pressure on the Setup Pressure Gauge
connected to the Cleaner Connector. Use a fl at blade
screwdriver to adjust the Wall Quick Connect Knob until the
pressure reads 25 PSI (+/- 5 PSI).
Note: The Wall Quick Connect can be adjusted from “0”
(fully closed) to “5” (fully open). Do NOTforce the
adjustment knob beyond “0” or “5”.
2. If the Wall Connector is on Position “5” (fully open) and the
pressure is still below 20 PSI, check for clogged Filter, Pump
Strainer Basket, Main Drain, Skimmer Basket, etc., to
determine why there is insufficient water pressure at the
dedicated line. If more pressure is still required have an
Authorized Hayward Pool Dealer or Service person check
the Booster Pump, F i l t r ation System and Plumbing to
determine if they are functioning correctly.
3. Turn the Booster Pump and Filtration Pump O F F.
4. R e m ove the Setup Pressure Gauge from the Cleaner
Connector. Store the Setup Pressure Gauge with the
Owner’s Guide in a safe place.
5. Attach the Cleaner Connector to Cleaner. The Sweep Hose
should be directly below the Pressure Hose.
6. Place the cleaner in the pool, turn the Filtration system O N,
then turn the Booster Pump O N.
Connecting Pressure Hose to Cleaner
Adjusting Pressure at Wall Connector
Setup Pressure Gauge & Wall Connect
K
C
U
C
7. Lu b r icate the swivel on the 3 ft. Hose Wall End A s s e mbly(Part T)
in soapy water then snap into one of the Pipe A ssemblies.
8. Lu b r i c ate the swivel on the Hose Cleaner End A s s e m b ly(Part S)
in soapy water then snap into a different Pipe A s s embly.
9. Open Bag #2 and lubricate both ends of the Hose Swivel
Assemblies (Part R) in soapy water. Connect the Pipe
Assemblies by snapping the Hose Swivel Assemblies into each
of the Pipe Assem blies.
Connecting Hose to Wall Fitting
1. With the Booster Pump and Filtration system turned O F F,
look down from the pool deck and hold the Wall Quick
Connect so the hose is to the left and the adjustment knob
is to the right. Insert the Wall Quick Connect into the
Universal Wall Fitting and turn it to the left (counter
clockwise) to lock. The hose should be on the bottom below
the adjustment knob.
2. Pull the Wall Quick Connect outward to check that the Wal l
Quick Connect is locked into the Universal Wall Fitting.
3. To di sconn ect the hose, first turn the Booster Pump and
Filtration pump O F F then push the Wall Quick Connect
toward the wall, turn it to the right (clockwise) and pull the
Wall Quick Connect out of the Universal Wall Fitting.
Disconnecting a Hose Pipe
If it is necessary to shorten, lengthen or replace a component
of the Rigid Pressure Hose, the Snap Fits can be undone by
twisting the connected Hose Pipes as shown.
8Use Only Genuine Hayward Replacement Parts.
Disconnecting Hose Pipes
Wall Quick Connect
Connecting The Rigid Pressure Hose to Pool Operating the Phantom Cleaner
Wall Connector Assembly
Hose Cleaner End Assembly
T QN
Hose Swivel Assembly
RN
Rigid Pressure Hose Assembly
S

9
Use Only Genuine Hayward Replacement Parts.
Warning - Risk of Injury
The Filtration and Booster Pumps must be OFF when connecting
or disconnecting cleaner hose.
Caution - Risk of Equipment Damage
The filter pump must alw ays be run to clear air from the system
before turning the Booster Pump ON. Never run the Booster
Pump without the main filter pump O N. Running the Booster
Pump dry will damage the Booster Pump and void the warranty.
Operating the Phantom Cleaner
1. Be sure all filtration system valves are open and supplying
water to the Booster Pump.
2. Be sure valves to and from the Booster Pump and dedicated
return line are fully opened.
3. The Phantom Cleaner and its Booster Pump can only
operate when the pool’s filter pump is operatin g .
Caution - Risk of Equipment Damage
Failure to open valves fully and/or failure to have the filtration
system operating will damage the Booster Pump.Thisdamage
voids the Booster Pump’s warranty.
Setting Pressure
Important: The cleaner will not operate properly if the pressure
is not properly set. Too little pressure will prevent proper
movement and cleaning.Too much pressure will cause poor
cleaning and premature wear of Cleaner parts.
Warning - Risk of Injury
Be careful to hold the Cleaner Connector (Part C) with the Setup
Pressure Gauge (Part U) attached under water and not to be
sprayed by the hole in the Setup Pressure Gauge or by the
Sweep Hose. Never point a jet or hose at people or pets.
Clip the Setup Pressure Gauge to the hose near the Wall Quick
Connect.
1. Turn the filtration system pump O N then the Booster Pump
ON. Read the pressure on the Setup Pressure Gauge
connected to the Cleaner Connector. Use a fl at blade
screwdriver to adjust the Wall Quick Connect Knob until the
pressure reads 25 PSI (+/- 5 PSI).
Note: The Wall Quick Connect can be adjusted from “0”
(fully closed) to “5” (full y open). Do N OTforce the
adjustment knob beyond “0” or “5”.
2. If the Wall Connector is on Position “5” ( fully open) and the
pressure is still below 20 PSI, check for clogged Filter, Pump
Strainer Basket, Main Drain, Skimmer Basket, etc., to
determine why there is insufficient water pressure at the
dedicated line. If more pressure is still required have an
Authorized Hayward Pool Dealer or Service person check
the Booster Pump, F i l t ration System and Plumbing to
determine if they are functioning correctly.
3. Turn the Booster Pump and Filtration Pump O F F.
4. R e m ove the Setup Pressure Gauge from the Cleaner
Connector. Store the Setup Pressure Gauge with the
Owner’s Guide in a safe place.
5. Attach the Cleaner Connector to Cleaner. The Sweep Hose
should be directly below the Pressure Hose.
6. Place the cleaner in the pool, turn the Filtration system ON,
then turn the Booster Pump O N.
Connecting Pressure Hose to Cleaner
Adjusting Pressure at Wall Connector
Setup Pressure Gauge & Wall Connect
K
C
U
C
7. Lu b ricate the swivel on the 3 ft. Hose Wall End A s s embly(Part T)
in soapy water then snap into one of the Pipe Assemblies.
8. Lu b r i cate the swivel on the Hose Cleaner End As s e m b ly(Part S)
in soapy water then snap into a different Pipe A s sembly.
9. Open Bag #2 and lubricate both ends of the Hose Swivel
Assemblies (Part R) in soapy water. Connect the Pipe
Assemblies by snapping the Hose Swivel Assemblies into each
of the Pipe Assem blies.
Connecting Hose to Wall Fitting
1. With the Booster Pump and Filtration system turned O F F,
look down from the pool deck and hold the Wall Quick
Connect so the hose is to the left and the adjustment knob
is to the right. Insert the Wall Quick Connect into the
Universal Wall Fitting and turn it to the left (counter
clockwise) to lock. The hose should be on the bottom below
the adjustment knob.
2. Pull the Wall Quick Connect outward to check that the Wall
Quick Connect is locked into the Universal Wall Fitting.
3. To di sconnect the hose, first turn the Booster Pump and
Filtration pump O F F then push the Wall Quick Connect
toward the wall, turn it to the right (clockwise) and pull the
Wall Quick Connect out of the Universal Wall Fitting.
Disconnecting a Hose Pipe
If it is necessary to shorten, lengthen or replace a component
of the Rigid Pressure Hose, the Snap Fits can be undone by
twisting the connected Hose Pipes as shown.
8Use Only Genuine Hayward Replacement Parts.
Disconnecting Hose Pipes
Wall Quick Connect
Connecting The Rigid Pressure Hose to Pool Operating the Phantom Cleaner
Wall Connector Assembly
Hose Cleaner End Assembly
T QN
Hose Swivel Assembly
RN
Rigid Pressure Hose Assembly
S

10 Use Only Genuine Hayward Replacement Parts.
R e m oving Debris Bag (Detail)
Attaching Debris Bag
1. Place the frame of the Debris Bag against the back
of the Cleaner as shown.
2. Press down on the top corners of the frame.
3. Press down on the top-center of the frame to lock
the Debris Bag in place.
R e m oving Debris Bag
1. Pull the top of the Debris Bag frame back (1) and then up (2).
Note: If you allow the bag to dry,the debris will be easier to remove.
Emptying Debris Bag
1. Hold Bag over trash can or wherever debris is to be placed.
2. Slide Float Closure off of bag .
3. Hold open edges apart and shake debris from bag.
4. Slide Float Closure onto bag.
Sand (dense debris)
If too much sand or heavy debris is collected in the Debris Bag,
the bag will “droop” over the hose while on the bottom and may
not be able to ascend to the surface properly. If you observe the
b ag drooping over the hose turn the booster pump off and empty
the Debris Bag .
Note: Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
Attaching Debris Bag
Emptying Debris Bag
B
Float Closure
11
Use Only Genuine Hayward Replacement Parts.
Correctly Operating CleanerLarge Capacity Debris Bag
M ov e m e n t
When the Phantom cleaner is operating properly it will randomly
travel around the bottom, sides and surface of the pool in “AUTO”
mode. The cleaner will clean the bottom and walls 2/3 of its
cycle and skim the surface 1/3 of the cycle. In “TOP” or “BOT ”
(Bottom) mode, the cleaner will stay in the Skimming or Bottom
& Wall mode (respectively) until the switch is changed to a
different mode.
Spi n - O u t
The cleaner will periodically stop and rotate clockwise in order
to provide better pool coverage and to escape from corners and
other obstacles. If the cleaner is momentarily stopped in a corner
or at an obstacle, it will Spin-Out to free itself and continue
moving randomly about the pool.The Spin-Out Cam determines
the frequency of the Spin-Outs.The cleaner comes equipped with
3 Spin-Out Cams; every 75, 50 (factory installed) or 30 seconds
(75 second and 30 second Cams are in the A c c e s s o ry bag). To
change Spin-Out Frequency see “Cha nging Spin-Out Cam”.
Sweep Hose
The Sweep Hose should move in a slow, u n d u l ating (snake-like)
motion. It moves debris out of tight corners so the cleaner can
vacuum the debris at a more accessible spot in the pool.
The Sweep Hose also stirs fine debris into suspension fo r
removal by the pool’s filtration system. The Sweep Hose Rollers
are wear parts. When the rollers wear-down to the outer gr oove
(Wear Line) replace the Wear Rollers (P/N AX5006A) a bag of
extra Wear Rollers is included. If a hole forms in the Sweep Hose,
it must be replaced with a genuine Hayward Phantom Sweep
Hose (P/N AX5000RSHA ).
Cle a n i n g
When the cleaner is on the bottom or walls debris is vacuumed
from below the cleaner and passed through the vacuum tube
into the Debris Bag . When the cleaner is skimming the surface
water jets push the debris into the Debris Bag where it is held
until the user empties the Bag . The cleaner may not pick-up all
debris on the first pass, but your pool should be clean in 3-hours
or less (depending on pool size, s h ape and the amount of debris
in the pool).
Observe the Phantom’s operation at regular intervals and empty
the bag as necessary. Only operate the Phantom for the time
neces sar y to clean the pool. Excessive use is unnecessary and
will cause premature cleaner wear.
Fine Debris
The Large Capacity Debris Bag , as with other pressure-side
cleaners, doesnot hold very fine sand or other powder-like
debris. Powder will be blown through the bag and into
suspension so it can be filtered by the pool’s filtration system.
Sand (Dense Debris)
If too much sand or heavy debris is collected in the Debris Bag ,
the bag will “droop ” over the hose while on the bottom and may
not be able to ascend to the surface. If you observe the bag
drooping over the hose turn the booster pump off and empty
the Debris Bag.
Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
The Phantom is designed to operate with 1/2-cup of sand and
the remainder of its bag filled with leav e s , aco rns, gras s es, etc.
Pressure Hose
This hose hasbeen designed to minimize the forming of loops
and knotting. Most of the pressure hose should remain below the
surface of the water the majority of the time. If the hose forms a
loop the cleaner will eventually work it out. In the rare event the
hose becomes knotted or tangled, it will limit the range of
the cleaner. To get optimal coverage, remove knots or bad
tangles if fou nd.
Sweep Hose
Wear Roller
Wear Line
(outer groove)
Wear Rollers (M)
Spin-Out Cams
75-Second 50-Second 30-Second
Sun Logo

10 Use Only Genuine Hayward Replacement Parts.
R e m oving Debris Bag (Detail)
Attaching Debris Bag
1. Place the frame of the Debris Bag against the back
of the Cleaner as shown.
2. Press down on the top corners of the frame.
3. Press down on the top-center of the frame to lock
the Debris Bag in place.
R e m oving Debris Bag
1. Pull the top of the Debris Bag frame back (1) and then up (2).
Note: If you allow the bag to dry,the debris will be easier to remove.
Emptying Debris Bag
1. Hold Bag over trash can or wherever debris is to be placed.
2. Slide Float Closure off of bag .
3. Hold open edges apart and shake debris from bag.
4. Slide Float Closure onto bag.
Sand (dense debris)
If too much sand or heavy debris is collected in the Debris Bag,
the bag will “droop” over the hose while on the bottom and may
not be able to ascend to the surface properly. If you observe the
b ag drooping over the hose turn the booster pump off and empty
the Debris Bag .
Note: Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
Attaching Debris Bag
Emptying Debris Bag
B
Float Closure
11
Use Only Genuine Hayward Replacement Parts.
Correctly Operating CleanerLarge Capacity Debris Bag
M ov e m e n t
When the Phantom cleaner is operating properly it will randomly
tr avel around the bottom, sides and surface of the pool in “AUTO”
mode. The cleaner will clean the bottom and walls 2/3 of its
cycle and skim the surface 1/3 of the cycle. In “TOP” or “BOT”
(Bottom) mode, the cleaner will stay in the Skimming or Bottom
& Wall mode (respectively) until the switch is changed to a
different mode.
Spin - O u t
The cleaner will periodically stop and rotate clockwise in order
to provide better pool coverage and to escape from corners and
other obstacles. If the cleaner is momentarily stopped in a corner
or at an obstacle, it will Spin-Out to free itself and continue
moving randomly about the pool.The Spin-Out Cam determines
the frequency of the Spin-Outs.The cleaner comes equipped with
3 Spin-Out Cams; every 75, 50 (factory installed) or 30 seconds
(75 second and 30 second Cams are in the A c c e s s o ry bag). To
change Spin-Out Frequency see “Changing Spin-Out Cam”.
Sweep Hose
The Sweep Hose should move in a slow, u n d u l ating (snake-like)
motion. It moves debris out of tight corners so the cleaner can
vacuum the debris at a more accessible spot in the pool.
The Sweep Hose also stirs fine debris into suspension fo r
removal by the pool’s filtration system. The Sweep Hose Rollers
are wear parts. When the rollers wear-down to the outer groove
(Wear Line) replace the Wear Rollers (P/N AX5006A) a bag of
extra Wear Rollers is included. If a hole forms in the Sweep Hose,
it must be replaced with a genuine Hayward Phantom Sweep
Hose (P/N A X5000RSHA).
Clea n i n g
When the cleaner is on the bottom or walls debris is vacuumed
from below the cleaner and passed through the vacuum tube
into the Debris Bag. When the cleaner is skimming the surface
water jets push the debris into the Debris Bag where it is held
until the user empties the Bag . The cleaner may not pick-up all
debris on the first pass, but your pool should be clean in 3-hours
or less (depending on pool size, s h ape and the amount of debris
in the pool).
Observe the Phantom’s operation at regular intervals and empty
the bag as necessary. Only operate the Phantom for the time
neces sar y to clean the pool. Excessive use is unnecessary and
will cause premature cleaner wear.
Fine Debris
The Large Capacity Debris Bag , as with other pressure-side
cleaners, doesnot hold very fine sand or other powder-like
debris. Powder will be blown through the bag and into
suspension so it can be filtered by the pool’s filtration system.
Sand (Dense Debris)
If too much sand or heavy debris is collected in the Debris Bag ,
the bag will “droop” over the hose while on the bottom and may
not be able to ascend to the surface. If you observe the bag
drooping over the hose turn the booster pump off and empty
the Debris Bag.
Pools with excessive amounts of sand should be manually
vacuumed before installing the Phantom.
The Phantom is designed to operate with 1/2-cup of sand and
the remainder of its bag filled with leav e s , aco rns, gra s ses, e tc.
Pressure Hose
This hose hasbeen designed to minimize the forming of loops
and knotting. Most of the pressure hose should remain below the
surface of the water the majority of the time. If the hose forms a
loop the cleaner will eventually work it out. In the rare event the
hose becomes knotted or tangled, it will limit the range of
the cleaner. To get optimal coverage, remove knots or bad
tangles if fou nd.
Sweep Hose
Wear Roller
Wear Line
(outer groove)
Wear Rollers (M)
Spin-Out Cams
75-Second 50-Second 30-Second
Sun Logo

Changing Top and Bottom Operation
The Top/Bottom Switch (Part P, page 4) is set to “AU T O”at the
factor y. The Phantom Cleaner will vacuum the pool bottom and
sides 2/3 of its cycle and skim the surface 1/3 of its cycle
automatic a l ly.
The cleaner can be easily adjusted to concentrate on the areas
of the pool with the most debris.
• To ONLY clean the bottom and sides of the pool,
m ove the switch to the right “BOT”.
• To ONLY skim the pool surfac e, m ove the switch
to the left “TOP”.
13
Use Only Genuine Hayward Replacement Parts.
12 Use Only Genuine Hayward Replacement Parts.
Adjusting Sweep Hose Po w e r
• In most pools it will not be necessary to adjust the
Sweep Hose power.
•O b s e rve the Phantom cleaner operating in the pool.
The Sweep Hose should move in a slow, u n d u l ating
(snake-like) motion.
•Sweep Hose Not Mov i n g : If the Sweep Hose does not
move side-to-side and just drags behind the cleaner, check
the Sweep Hose for holes. Check for debris behind the
adjustment knob or in the jet-end of the Sweep Hose.
•Sweep Hose Moves Slowly Or Not At All: Turn the
adjustment knob counter-clockwise to increase Sweep
Hose power.
•Sweep Hose Frequently Sprays Out Of The Pool:
Turn the adjustment knob cloc kwise to reduce Sweep
Hose power.
Note: Do NOTturn the Sweep Hose completely off .
This can cause the hose to tangle or knot.
Phantom Cleaner Adjustments
Warning – Risk of Injury
Turn the Booster Pump and Filtration Pump OFF before
making adjustments to the cleaner. Always make
adjustments outside of the pool. Failure to do so may
cause injury.
Changing Spin-Out Frequency
• In most pools it will not be necessary to change the Spin-Out
frequency.
•The cleaner comes with a 3-prong Spin-Out cam installed,
which makes the Phantom cleaner Spin-Out once every
50-seconds. This is appr op ria te for most pools.
• Pools that are small or have many sharp corners or other
obstacles may benefit from more frequent Spin-Outs. For
such pools, open the Cam Cap and replace the 3-prong cam
with the 5-prong 30 second cam.
• Pools that are very large and/or have very few obstacles may
benefit from less frequent Spin-Outs. For such pools, open
the Cam Cap and replace the 3-prong cam with the 2-prong
75-second cam.
•The goal is to maximize cleaning time and minimize the
amount of time spinning out.
• If the cleaner is spending too much time at an obstacle
waiting for a Spin-Out, use a cam with more prongs for more
frequent Spin-Outs.
• If the cleaner rarely needs to Spin-Out near an obstacle then
a cam with fewer prongs and less frequent Spin-Outs will
increase effective cleaning time.
• If the cleaner has a tendency to stay in the deep end (not
cleaning the shallow end suffic ien tly), in pools with a
particul a r ly steep or long slopes between the deep and
shallow ends, we recommend using a cam with fewer
prongs, it will promote longer straight runs.
Changing Spin-Out Cam
1. Turn the Cam Cap counter clockwise to open.
2. Remove the Spin-Out Cam.
3. Place the desired Cam in place over the stem.
4. Place unused Cams in A c c e s s o ry Bag and store in a safe
place with the Owner’s Guide.
5. Close the Cam Cap .
Adjusting Spin-Out Duration
Each Cam has a “Summer” side and a “Wint er” side (see Sun &
Snowflake logos on each Cam). The Summer side is usually
preferred. If the pool water is cold (below 60 degrees F), th e
Pressure Hose becomes stiffer and may prevent the Cleaner
from Spinning-Out enough to escape from obstacles.The
“Winter” Cam side will provide longer Spin-Outs so the Cleaner
operates better in cold water.
1. Turn the Cam Cap to open
2. Remove the Cam, turn it over and replace the Cam so the
desired (Sun or Snowflake) side is face-up.
•If the cleaner is making more than three attempts to escap e
from an obstacle, use the “Wi nter” side.
•If the cleaner regularly spins-out more than three-quarters
of a turn, use the “Sum mer” side.
Cam Cap on Deck
Top/Auto/Bot Switch
Cam Cap Open
Adjusting Sweep Hose Pow er
Spin-Out Cams
75-Second 50-Second 30-Second
Cam Cap (F)
Cam Cap (F)
Sun Logo
Spin-Out Cam

Changing Top and Bottom Operation
The Top/Bottom Switch (Part P, page 4) is set to “AU T O”at the
factor y. The Phantom Cleaner will vacuum the pool bottom and
sides 2/3 of its cycle and skim the surface 1/3 of its cycle
automati c a l ly.
The cleaner can be easily adjusted to concentrate on the areas
of the pool with the most debris.
• To ONLY clean the bottom and sides of the pool,
m ove the switch to the right “BOT”.
• To ONLY skim the pool surfac e, m ove the switch
to the left “TOP”.
13
Use Only Genuine Hayward Replacement Parts.
12 Use Only Genuine Hayward Replacement Parts.
Adjusting Sweep Hose Po w e r
• In most pools it will not be necessary to adjust the
Sweep Hose power.
•O b s e rve the Phantom cleaner operating in the pool.
The Sweep Hose should move in a slow, u n d u l ating
(snake-like) motion.
•Sweep Hose Not Mov i n g : If the Sweep Hose does not
move side-to-side and just drags behind the cleaner, check
the Sweep Hose for holes. Check for debris behind the
adjustment knob or in the jet-end of the Sweep Hose.
•Sweep Hose Moves Slowly Or Not At All: Turn the
adjustment knob counter-clockw ise to increase Sweep
Hose power.
•Sweep Hose Frequently Sprays Out Of The Po ol:
Turn the adjustment knob cloc kwise to reduce Sweep
Hose power.
Note: Do NOTturn the Sweep Hose completely off .
This can cause the hose to tangle or knot.
Phantom Cleaner Adjustments
Warning – Risk of Injury
Turn the Booster Pump and Filtration Pump OFF before
making adjustments to the cleaner. Always make
adjustments outside of the pool. Failure to do so may
cause injury.
Changing Spin-Out Frequency
• In most pools it will not be necessary to change the Spin-Out
frequency.
•The cleaner comes with a 3-prong Spin-Out cam installed,
which makes the Phantom cleaner Spin-Out once every
50-seconds. This is app ro pr ia te for most pools.
• Pools that are small or have many sharp corners or other
obstacles may benefit from more frequent Spin-Outs. For
such pools, open the Cam Cap and replace the 3-prong cam
with the 5-prong 30 second cam.
• Pools that are very large and/or have very few obstacles may
benefit from less frequent Spin-Outs. For such pools, open
the Cam Cap and replace the 3-prong cam with the 2-prong
75-second cam.
•The goal is to maximize cleaning time and minimize the
amount of time spinning out.
• If the cleaner is spending too much time at an obstacle
waiting for a Spin-Out, use a cam with more prongs for more
frequent Spin-Outs.
• If the cleaner rarely needs to Spin-Out near an obstacle then
a cam with fewer prongs and less frequent Spin-Outs will
increase effective cleaning time.
• If the cleaner has a tendency to stay in the deep end (not
cleaning the shallow end suffic ien tly) , in pools with a
particu l a r ly steep or long slopes between the deep and
shallow ends, we recommend using a cam with fewer
prongs, it will promote longer straight runs.
Changing Spin-Out Cam
1. Turn the Cam Cap counter clockwise to open.
2. Remove the Spin-Out Cam.
3. Place the desired Cam in place over the stem.
4. Place unused Cams in A c c e s s o ry Bag and store in a safe
place with the Owner’s Guide.
5. Close the Cam Cap .
Adjusting Spin-Out Duration
Each Cam has a “Su mmer” side and a “ Winter” side (see Sun &
Snowflake logos on each Cam). The Summer side is usually
preferred. If the pool water is cold (below 60 degrees F), the
Pressure Hose becomes stiffer and may prevent the Cleaner
from Spinning-Out enough to escape from obstacles.The
“Winter” Cam side will provide longer Spin-Outs so the Cleaner
operates better in cold water.
1. Turn the Cam Cap to open
2. Remove the Cam, turn it over and replace the Cam so the
desired (Sun or Snowflake) side is face-up.
•If the cleaner is making more than three attempts to escap e
from an obstacle, use the “Wint er” side.
•If the cleaner regularly spins-out more than three-quarters
of a turn, use the “Summe r” side.
Cam Cap on Deck
Top/Auto/Bot Switch
Cam Cap Open
Adjusting Sweep Hose Pow er
Spin-Out Cams
75-Second 50-Second 30-Second
Cam Cap (F)
Cam Cap (F)
Sun Logo
Spin-Out Cam

Cleaning the In-Line Filter
1. The In-Line filter (Part Q) is located by the Wall Quick
Connect (Part K).
2. To remove the screen inside the In-Line Filter, unscrew
the cap of the In-Line Filter and remove the screen.
3. Remove the debris from the screen and rinse.Important: If
the screen frequently becomes plugg e d , the filtration
system is not performing properly or there is another
plumbing problem.
4. Place the open end of the screen into the outlet end of the
In-Line Filter and screw the cap back on. Important: Make
sure the O-Ring is in place and properly seated.
Caution - Risk of Equipment Damage
Never operate the cleaner without the screen in place.
Operating the cleaner without the screen will damage the
cleaner’s internal mechanism.
15
Use Only Genuine Hayward Replacement Parts.
14 Use Only Genuine Hayward Replacement Parts.
Sweep Hose
• Sweep Hose Wear Rollers will experience wear when
o p e r ating in a plastered or concrete pool.
•When the Wear Rollers wear-down to the outer groove
(Wear Line) replace the Wear Rollers (P/N AX 5006A).
• Check the Sweep Hose for holes
(Replace if necessary with P/N: AX5000RSHA).
Some parts will wear with normal use. To ensure the high quality
p e r fo r m a n c e , insist on Genuine Hayward replacement parts
(using non-Hayward replacement parts will Void the
Phantom Cleaner’s Warranty). The following parts are user
r e p l a c e abl e and subject to normal wear and tear.
1. Sweep Hose: If a hole forms in the Sweep Hose, it should
be replaced. Unscrew the metal mender nut from the hose
and pull the Sweep Hose (Sweep Hose Replacement Part
Number: AX5000RSHA) off the Cleaner Connector. Attach a
new Sweep Hose to the Cleaner Connector.
2. Large Capacity Debris Bag with Float: The Debris Bag
should be replaced if it is torn (Replacement Part Number:
AX6000BA).
3. Swivels: If a swivel ceases to turn easily or leaks while
the cleaner is running, it shouldbe replaced.
Storing the Phantom Cleaner
1. Turn the Booster Pump OFF and set the timer so the
Booster Pump will not turn on while the Phantom cleaner is
out of the pool (Never ope rate the Booster Pump without
the cleaner connected).
2. Disconnect Wall Quick Connect from the Universal Wal l
Fitting. The Universal Wall Fitting may be left in place.
3. The cleaner is constructed of the finest materials available,
however we recommend that when the Phantom cleaner is
removed from the pool, it should be stored fl at on its wheels
in a shaded area to protect the unit form excessive exposure
to sunlight.
4. Store the Sweep Hose and the Hose Cleaner End A ssembly
(Part S) straight and fl at, not coiled.The Rigid Hose Pipe
Sections may be folded on one another, so that the short
hoses in-between are bent. If possible, store the hoses in
the shade.
Winterizing the Cleaner
When closing your pool for the winter completely drain the wate r
from the Phantom Cleaner (by slowing rotating it in all directions)
and Hoses. Store the Phantom Cleaner indoors to prevent
freezing of the inner mechanisms.
Periodic Freezing Conditions
If you are in an area subject to periodic freezing conditions, but
pool equipment is kept in operation, it is very important that the
filtration system and Phantom cleaner be in operation during
times when hard freezing occurs (normally between 3 AM and
7AM). Running the Phantom cleaner at this time will ensure
against damaging the Cleaner and may prevent freezing the
pool wat e r.
Maintenance Storing the Phantom Cleaner
Rem o ving the Phantom Cleaner From the Pool
Warning – Risk of Injury
The Booster Pump and Filtration Pump must be OFF when
connecting or disconnecting cleaner or hose.
1. Turn the Booster Pump and Filtration Pump OFF.If
you will not be replacing the cleaner before the next Booster
Pump timer cycle, turn the Booster Pump Timer OFF.N ever
run the Booster Pump without the cleaner connected.
Failure to do so can cause serious injury.
Caution - Risk of Equipment Damage
Never run the Booster Pump without the Cleaner connected.
Doing so will damage the pump’s motor and void the Booster
Pump’s warranty.
2. From the pool deck looking down push the Wall Quick
Connect into the Universal Wall Fitting and turn it to the right
(clockwise).
3. Pull the Wall Quick Connect out of the Universal Wall Fitting.
4. G r ab the cleaner by the wing, and remove from the pool.
5. Disconnect the Cleaner Connector from the Phantom
Cleaner.
6. Lay the Cleaner End of the Pressure Hose and the Sweep
Hose fl at and straight.
Important: A lw ays store the Cleaner End of the Pressure Hose
and the Sweep Hose straight, not coiled.The cleaner may not
operate properly with these hoses bent.
Emptying the Debris Bag
•Empty the Debris Bag regularly. Do not continue to operat e
the Phantom when the bag is full.
1. Hold Bag over trashcan or wherever debris is to be placed.
2. Slide Float Closure off of bag.
3. Hold open edges apart and shake debris from bag .
4. Slide Float Closure onto bag.
•Sand (dense debris): Always empty the Phantom
Debris Bag when there is too much sand (or heavy
debris). If the Cleaner cannot climb to the surface in TOP
or AUTO mode OR the Bag “droops” over the hose turn the
Booster Pump OFF and empty the Debris Bag.
• When the bag is full of leaves or other debris, the debris may
t r apair in the bag while skimming the surface. If the trapped
air prevents the cleaner from descending to the pool bottom,
empty the Debris Bag .
DO NOT operate the Phantom if it runs on its side or
upside-dow n.
In-Line Filter
Wear Roller
Wear Line
(outer groove)
In-Line Filter
Screen

Cleaning the In-Line Filter
1. The In-Line filter (Part Q) is located by the Wall Quick
Connect (Part K).
2. To remove the screen inside the In-Line Filter, unscrew
the cap of the In-Line Filter and remove the screen.
3. Remove the debris from the screen and rinse.Impo rtant: If
the screen frequently becomes plugg e d , the filtration
system is not performing properly or there is another
plumbing problem.
4. Place the open end of the screen into the outlet end of the
In-Line Filter and screw the cap back on. Impor tant: Mak e
sure the O-Ring is in place and properly seated.
Caution - Risk of Equipment Damage
Never operate the cleaner without the screen in place.
Operating the cleaner without the screen will damage the
cleaner’s internal mechanism.
15
Use Only Genuine Hayward Replacement Parts.
14 Use Only Genuine Hayward Replacement Parts.
Sweep Hose
• Sweep Hose Wear Rollers will experience wear when
o p e r ating in a plastered or concrete pool.
•When the Wear Rollers wear-down to the outer groove
(Wear Line) replace the Wear Rollers (P/N AX5006A ).
• Check the Sweep Hose for holes
(Replace if necessary with P/N: AX5000R SHA).
Some parts will wear with normal use. To ensure the high quality
p e r fo r m a n c e , insist on Genuine Hayward replacement parts
(using non-Hayward replacement parts will Void the
Phantom Cleaner’s Warran ty). The following parts are user
r e p l a c e abl e and subject to normal wear and tear.
1. Sweep Hose: If a hole forms in the Sweep Hose, it should
be replaced. Unscrew the metal mender nut from the hose
and pull the Sweep Hose (Sweep Hose Replacement Part
Number: AX5000RSHA) off the Cleaner Connector. Attach a
new Sweep Hose to the Cleaner Connector.
2. Large Capacity Debris Bag with Float: The Debris Bag
should be replaced if it is torn (Replacement Part Number:
AX6000BA).
3. Swivels: If a swivel ceases to turn easily or leaks while
the cleaner is running, it shouldbe replaced.
Storing the Phantom Cleaner
1. Turn the Booster Pump OFF and set the timer so the
Booster Pump will not turn on while the Phantom cleaner is
out of the pool (Never operate the Booster Pump without
the cleaner connected).
2. Disconnect Wall Quick Connect from the Universal Wal l
Fitting. The Universal Wall Fitting may be left in place.
3. The cleaner is constructed of the finest materials available,
however we recommend that when the Phantom cleaner is
removed from the pool, it should be stored fl at on its wheels
in a shaded area to protect the unit form excessive exposure
to sunlight.
4. Store the Sweep Hose and the Hose Cleaner End Assembly
(Part S) straight and fl at, not coiled.The Rigid Hose Pipe
Sections may be folded on one another, so that the short
hoses in-between are bent. If possible, store the hoses in
the shade.
Winterizing the Cleaner
When closing your pool for the winter completely drain the wate r
from the Phantom Cleaner (by slowing rotating it in all directions)
and Hoses. Store the Phantom Cleaner indoors to prevent
freezing of the inner mechanisms.
Periodic Freezing Conditions
If you are in an area subject to periodic freezing conditions, but
pool equipment is kept in operation, it is very important that the
filtration system and Phantom cleaner be in operation during
times when hard freezing occurs (normally between 3 AM and
7AM). Running the Phantom cleaner at this time will ensure
against damaging the Cleaner and may prevent freezing the
pool wat e r.
Maintenance Storing the Phantom Cleaner
Remo ving the Phantom Cleaner From the Poo l
Warning – Risk of Injury
The Booster Pump and Filtration Pump must be OFF when
connecting or disconnecting cleaner or hose.
1. Turn the Booster Pump and Filtration Pump OFF.If
you will not be replacing the cleaner before the next Booster
Pump timer cycle, turn the Booster Pump Timer OFF.Never
run the Booster Pump without the cleaner connected.
Failure to do so can cause serious injury.
Caution - Risk of Equipment Damage
Never run the Booster Pump without the Cleaner connected.
Doing so will damage the pump’s motor and void the Booster
Pump’s warranty.
2. From the pool deck looking down push the Wall Quick
Connect into the Universal Wall Fitting and turn it to the right
(clockwise).
3. Pull the Wall Quick Connect out of the Universal Wall Fitting.
4. G r ab the cleaner by the wing, and remove from the pool.
5. Disconnect the Cleaner Connector from the Phantom
Cleaner.
6. Lay the Cleaner End of the Pressure Hose and the Sweep
Hose fl at and straight.
Important: A lw ays store the Cleaner End of the Pressure Hose
and the Sweep Hose straight, not coiled.The cleaner may not
operate properly with these hoses bent.
Emptying the Debris Bag
•Empty the Debris Bag regularly. Do not continue to operat e
the Phantom when the bag is full.
1. Hold Bag over trashcan or wherever debris is to be placed.
2. Slide Float Closure off of bag.
3. Hold open edges apart and shake debris from bag .
4. Slide Float Closure onto bag.
•Sand (dense debris): Always empty the Phantom
Debris Bag when there is too much sand (or heavy
debris). If the Cleaner cannot climb to the surface in TOP
or AUTO mode OR the Bag “d roops” over the hose turn the
Booster Pump OFF and empty the Debris Bag.
• When the bag is full of leaves or other debris, the debris may
t r apair in the bag while skimming the surface. If the trapped
air prevents the cleaner from descending to the pool bottom,
empty the Debris Bag .
DO NOT operate the Phantom if it runs on its side or
upside-down.
In-Line Filter
Wear Roller
Wear Line
(outer groove)
In-Line Filter
Screen

17
Use Only Genuine Hayward Replacement Parts.
16 Use Only Genuine Hayward Replacement Parts.
Booster Pump
Booster Pump Typical Installation
From Pool To Pool
Filtration Pump Pool Filter Heater To Spa
Plumbing
Options
Chlorinator
Solar System
Booster Pump
(sold separately)
Phantom
Ref . N o . Part No. Des c r i p t i o n
1AX5060M Motor (3/4 HP 60 cycles)
2a AX5060B Seal Plate (Prior to 2004)
2b AX5060B2 Seal Plate (2004 and beyo nd)
3SPX1250XZ2C Spring Seal with Seat
4AX5060C Impeller Ass emb ly
5a AX5060GA Flat Gasket, Booster Pump (Prior to 2004)
5b AX5060J R i bbon Gasket, Booster Pump (2004 and beyo nd )
6AX5060A Volute 3/4” N PT-F
7SPX1700FG Pipe Plug with Gasket
8AX5060Z2A1 Nut, Bolt and Washer Kit (6-pack)
9AX5060RSA1 Motor Bolt with Washer Kit (4-pack)
10 AX5060P Stem Bumper
11 AX5060D Base
12 AX5060HKIT Booster Pump Hose Kit
13 AX5060K Metal Flange (Prior to 2004) Not Shown
Optional 5060VKIT Vertical Installation Kit
Troubleshooting
For Technical Assistance Call:
1-800-227-1477

17
Use Only Genuine Hayward Replacement Parts.
16 Use Only Genuine Hayward Replacement Parts.
Booster Pump
Booster Pump Typical Installation
From Pool To Pool
Filtration Pump Pool Filter Heater To Spa
Plumbing
Options
Chlorinator
Solar System
Booster Pump
(sold separately)
Phantom
Ref. N o . Part No. Description
1AX5060M Motor (3/4 HP 60 cycles)
2a AX5060B Seal Plate (Prior to 2004)
2b AX5060B2 Seal Plate (2004 and beyo nd )
3SPX1250XZ 2C Spring Seal with Seat
4AX5060C Impeller Ass emb ly
5a AX5060GA F lat Gasket, Booster Pump (Prior to 2004)
5b AX5060J R i bbon Gasket, Booster Pump (2004 and beyo nd )
6AX5060A Volute 3/4” NPT-F
7SPX1700FG Pipe Plug with Gasket
8AX5060Z2A 1 Nut , Bolt and Washer Kit (6-pack)
9AX5060RSA 1 Motor Bolt with Washer Kit (4-pack)
10 AX5060P Stem Bumper
11 AX5060D Ba se
12 AX5060HK IT Booster Pump Hose Kit
13 AX5060K Metal Flange (Prior to 2004) Not Shown
Optional 50 60V KIT Vertical Installation Kit
Troubleshooting
For Technical Assistance Call:
1-800-227-1477

19
Use Only Genuine Hayward Replacement Parts.
Imp o r t a n t !
Retain Your Bill of Sale For Proof of Warranty Eligibility
To the Original Retail Consumer / Purchaser (the “PURCHASER ”)
of the Hayward Phantom Automatic Pool Cleaner (the
“CLEANER”).
Hayward Pool Products, Inc. (“HAYWARD”) warrants the parts for
One (1) year form the date of original purchase (excluding the
bag and sweep hose which are normal replacement parts).
The Hayward Booster Pump is ex cluded in this warranty
and carries its own separate warranty.
SHOULD THE CLEANER FAIL TO BE IN GOOD WORKING ORDER
IN ACCORDANCE WITH THE ABOVE SCHEDULE, HAYWARD WILL
AT ITS OPTION REPAIR OR REPLACE THE CLEANER OR ANY
DEFECTIVE PA RTS AT NO ADDITIONAL CHARGE EXCEPT
AS SET FORTH BELOW. REPAIR PARTS AND REPLACEMENT
PRODUCTS WILL BE FURNISHED ON AN EXCHANGE BASIS AND
WILL BE NEW OR FUNCTIONALLY EQUIVALENT.ALL PARTS
REMOVED AS A RESULT OF REPLACEMENT SHALL BECOME
THE PROPERTY OF HAYWARD. LIABILITY OF HAY WARD AND THE
SOLE REMEDY OF THE PURCHASER WHETHER IN CONTRACT
UNDER ANY WARRAN TY, IN TORT (INCLUDING NEGLIGENCE), IN
STRICT LIABILITY OR OTHERWISE, SHALL BE LIMITED TO THE
REPAIR OR REPLACEMENT OF DEFECTIVE PARTS ONLY AND
SHALL IN NO EVENT EXCEED THE RETURN OF THE AMOUNT OF
THE PURCHASE PRICE PAID BY THE PURCHASER.
THIS LIMITED WARRANTY IS SUBJECT TO THE
FOLLOWING TERMS AND CONDITIONS:
1. This Limited Warranty shall not ap p ly to damage caused by
failure to perform normal maintenance on the CLEANER
(e.g. monitoring pressure/flow and replacing a worn bag
and sweep hose).
2. This Limited Warranty shall be void if the CLEANER is
modified in any respect, including, but not limited to the use
of any parts other than Genuine Hayward Parts.
3. This Limited Warranty shall not ap p ly to any injury, loss,
damage, defect or malfunction of the CLEANER or failure of
the CLEANER to function resulting form any failure to
operate or maintain the CLEANER in accordance with the
directions contained in the Owner’s Guide provided by
HAYWARD or any injury, loss, damage, defect, malfunction
or failure to function resulting from any misuse,
unreasona ble use, ta mpering, abuse, accident, act of God,
alterations in the CLEANER by anyone other than HAYWARD
including but not limited to such damages or injuries to
parts resulting from running pump dry (e.g. interruption in or
inade q uate supply of water to the Booster Pump, or
obstruction in lines, or otherwise); or damag e , defec ts, or
malfunctions resulting from defects in, failure or malfunction
of, or negligence, abuse, or misuse with respect to
equipment other than the CLEANER.
4. This Limited Warranty shall not ap p ly to the malfunction of,
damage to, m aterials failure in, or changes in the
appearance of the CLEANER resulting from exposure to
sunlight or chemicals or chemical reactions to substances
with which any part of the CLEANER may come in contact or
parts if worn, do not affect performance of the CLEANER.
5. This Limited Warranty does not apply to cleaners used for
commercial purposes.
6. The CLEANER is designed to function in a properly
designed, constructed and maintained pool. The Limited
Warranty does not ap p lyin the circumstances where the
pool’s design, construction or maintenance is defective,
substandard or inap p r o p r i ate for the CLEANER’S operation.
7. Deterioration, di s colo r ation or brittleness of pool plaster and
v i nyl liners can be caused over time separat e ly by, or in
combination with, algae and an imbalance in pool water
chemist ry, improper installation, and other factors.
Limited Warranty
Phantom Parts Diagram Limited Warranty
18 Use Only Genuine Hayward Replacement Parts.
Ref. No. Part No. Description
1AX6000TA Deck (with Wing & Cam Cap )
2AX6001F Cam Cap
3 AX5003M Cams (3-pack)
4AX6000GA Gearbox (with Cams, Hoses & Ties)
5AX5010D4 Screws (5-pack)
6AX6009BF Front Wheel (with Retainer & Bearing)
7AX5000D Rollers (7-pack with Bearing)
8AX6000MA M a n i fold Assembly (with Hoses & Ties)
9AX5000B Vac Tu be
10 AX5000A2 Bottom Housing
11 AX5009E Rear A xle
12 AX6009B Rear Wheels (with Bearings, Nuts & Hubcap s )
13 AX6000HA R i gid Pressure Hose (complete)
14 AX6000HCA Pressure Hose Cleaner End Assembly
(Without Sweep Hose)
15 AX6000HWA2 Pressure Hose and Top of In-Line Filter As sem bly
16 AX6000HFA Hose Swivel Ass emb ly
17 AX6000HE R i gid Hose Pipe Section (2 Rigid Pipes & 1 Coupling)
18 AX6000HWA1 Wall Quick Connect, Hos e, Bottom In-Line Filter
Ass e mb ly
19 AX6009S In-Line Filter Screen
20 AX6000PTA Set-up Pressure Gauge
21 AX5000RSHA Sweep Hose (with Rollers & Mender Nut)
22 AX6000BA Large Capacity Debris Bag (with Float)
23 AX5004L1 Universal Wall Fitting
24 AX5006A Wear Rollers (10-pack)
25 AX5500EF F l o ats (Left & Right)
26 AX6000SWA Top / Auto / Bot Switch
27 AX6000TNKA Nose Jet Tan k
28 AX6008M Front Spin-Out Jet (with hose & tie)
29 AX5010G10 Wall Quick Connect O-Ring
30 AX5010G18 Cleaner-Connector O-Ring
31 AX5010G19 In-Line Filter O-Ring
32 AX5010G5 Pipe Connector O-Ring (6-pack)
Phantom Cleaner Hoses (13)
1
2
3
7
8
9
4
27
5
26
12
10
25
20
21 24
22
6
Phantom Cleaner Exploded View
11
28
1 5
1 7
1 4
3 1 1 9
1 6
1 8
2 3
2 9
30

19
Use Only Genuine Hayward Replacement Parts.
Impor t a n t !
Retain Your Bill of Sale For Proof of Warranty Eligibility
To the Original Retail Consumer / Purchaser (the “PURCHASER”)
of the Hayward Phantom Automatic Pool Cleaner (the
“CLEANER”).
Hayward Pool Products, Inc. (“H AY WARD”) warrants the parts for
One (1) year form the date of original purchase (excluding the
bag and sweep hose which are normal replacement parts).
The Hayward Booster Pump is excluded in this warranty
and carries its own separate warranty.
SHOULD THE CLEANER FAIL TO BE IN GOOD WORKING ORDER
IN ACCORDANCE WITH THE ABOVE SCHEDULE, HAYWARD WILL
AT ITS OPTION REPAIR OR REPLACE THE CLEANER OR ANY
DEFECTIVE PARTS AT NO ADDITIONAL CHARGE EXCEPT
AS SET FORTH BELOW. REPAIR PARTS AND REPLACEMENT
PRODUCTS WILL BE FURNISHED ON AN EXCHANGE BASIS AND
WILL BE NEW OR FUNCTIONALLY EQUIVALENT.ALL PARTS
REMOVED AS A RESULT OF REPLACEMENT SHALL BECOME
THE PROPERTY OF HAYWARD. LIABILITY OF HAYWARD AND THE
SOLE REMEDY OF THE PURCHASER WHETHER IN CONTRACT
UNDER ANY WARRANTY, IN TORT (INCLUDING NEGLIGENCE), IN
STRICT LIABILITY OR OTHERWISE, SHALL BE LIMITED TO THE
REPAIR OR REPLACEMENT OF DEFECTIVE PARTS ONLY AND
SHALL IN NO EVENT EXCEED THE RETURN OF THE AMOUNT OF
THE PURCHASE PRICE PAID BY THE PURCHASER.
THIS LIMITED WARRANTY IS SUBJECT TO THE
FOLLOWING TERMS AND CONDITIONS:
1. This Limited Warranty shall not ap p ly to damage caused by
failure to perform normal maintenance on the CLEANER
(e.g. monitoring pressure/flow and replacing a worn bag
and sweep hose).
2. This Limited Warranty shall be void if the CLEANER is
modified in any respect, including, but not limited to the use
of any parts other than Genuine Hayward Parts.
3. This Limited Warranty shall not ap p ly to any injury, loss,
damage, defect or malfunction of the CLEANER or failure of
the CLEANER to function resulting form any failure to
operate or maintain the CLEANER in accordance with the
directions contained in the Owner’s Guide provided by
HAYWARD or any injury, loss, damage, def ect, malfunctio n
or failure to function resulting from any misuse,
unreasona ble use, tamper ing, abuse, acc ident, act of God,
alterations in the CLEANER by anyone other than HAYWARD
including but not limited to such damages or injuries to
parts resulting from running pump dry (e.g. interruption in or
inad e q uate supply of water to the Booster Pump, or
obstruction in lines, or otherwise); or damag e , defects, or
malfunctions resulting from defects in, failure or malfunction
of, or negligence, abuse, or misuse with respect to
equipment other than the CLEANER.
4. This Limited Warranty shall not ap p ly to the malfunction of,
damage to, m aterials failure in, or changes in the
appearance of the CLEANER resulting from exposure to
sunlight or chemicals or chemical reactions to substances
with which any part of the CLEANER may come in contact or
parts if worn, do not affect performance of the CLEANER.
5. This Limited Warranty does not apply to cleaners used for
commercial purposes.
6. The CLEANER is designed to function in a properly
designed, constructed and maintained pool.The Limited
Warranty does not ap p lyin the circumstances where the
pool’s design, construction or maintenance is defective,
substandard or inap p r o p r i ate for the CLEANER’S operation.
7. Deterio rati on, d iscol o ration or brittleness of pool plaster and
v i nyl liners can be caused over time separat e ly by, or in
combination with, algae and an imbalance in pool water
chemis t ry, improper installation , and other factors.
Limited Warranty
Phantom Parts Diagram Limited Warranty
18 Use Only Genuine Hayward Replacement Parts.
Ref. No. Part No. Descrip tio n
1AX6000TA Deck (with Wing & Cam Cap )
2AX6001F Cam Cap
3 AX5003M Cams (3-pack)
4AX6000GA Gearbox (with Cams, Hoses & Ti es)
5AX5010D4 Screws (5-pack)
6AX6009BF Front Wheel (with Retainer & Bearing)
7AX5000D Rollers (7-pack with Bearing)
8AX6000MA M a n i fold Assem bly (with Hoses & Ties)
9AX5000B Vac Tu be
10 AX5000A2 Bottom Housing
11 AX5009E Rear Axle
12 AX6009B Rear Wheels (with Bearings, Nuts & Hubcap s )
13 AX6000HA R i gid Pressure Hose (complete)
14 AX6000HC A Pressure Hose Cleaner End A ssembly
(Without Sweep Hose)
15 AX6000HWA2 Pressure Hose and Top of In-Line Filter As sem bly
16 AX6000HFA Hose Swivel Ass emb ly
17 AX6000HE R i gid Hose Pipe Section (2 Rigid Pipes & 1 Coupling)
18 AX6000HWA1 Wall Quick Connect, Hos e, Bottom In-Line Filter
Ass emb ly
19 AX6009S In-Line Filter Screen
20 AX6000PTA Set-up Pressure Gauge
21 AX5000RS HA Sweep Hose (with Rollers & Mender Nut)
22 AX6000BA Large Capacity Debris Bag (with Float )
23 AX5004L1 Universal Wall Fitting
24 AX5006A Wear Rollers (10-pack)
25 AX5500EF F l o ats (Left & Right)
26 AX6000SWA Top / Auto / Bot Switch
27 AX6000TN KA Nose Jet Tank
28 AX6008M Front Spin-Out Jet (with hose & tie)
29 AX5010G1 0 Wall Quick Connect O-Ring
30 AX5010G1 8 Cle aner-Connector O-Ring
31 AX5010G1 9 In-Line Filter O-Ring
32 AX5010G5 Pipe Connector O-Ring (6-pack)
Phantom Cleaner Hoses (13)
1
2
3
7
8
9
4
27
5
26
12
10
25
20
21 24
22
6
Phantom Cleaner Exploded View
11
28
1 5
1 7
1 4
3 1 1 9
1 6
1 8
2 3
2 9
30