Winners Only BD3001CKHN User manual

PROD. NO.:
NOTE: Bunkie Board must be used to replace Box Spring.
NO QTY
A HB Left Leg 1 PC NO Description Size Sketcher QTY
B HB Right Leg 1 PC 1 Allen Key 4*74*29mm 1 PC
C Headboard 1 PC 2 Bolt 1/4"*15*45mm 12 PCS
D Wood stretcher 1 PC 3 Spring Washer 1/4"*11*2mm 12 PCS
E Panel Footboard 1 PC 4 Flat Washer 1/4*18*2mm 12 PCS
F Side Rail 2 PCS 5 Screw Ø8*30mm 10 PCS
G Slat 5pcs
H Support Leg 10 PCS
Page 1 of 2 MADE IN VIETNAM
WINNERS ONLY ®
1. We recommend that you should assemble this product with the assistance of another person; this will make the assembly easier, and will help to prevent personal injury and
to insure parts are not damaged during the assembly process.
2. Before beginning, please check the packing materials carefully for small parts which may have come loose inside the carton during shipping. Please do not discard any
packing material until all parts have been located. If any parts are missing, please contact your dealer for prompt replacement.
3. To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for stain residues and rough surfaces and also check for staples or nails left after
removing the packing materials. The manufacturer will not be held responsible if preventive steps are not taken prior to installation.
4. Please do not over tighten screws or bolts. During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be periodically inspected and re-
tightened to prevent damage to the furniture and (or) personal property or cause injury. Always check to be sure all hardware on this list and the below mentioned components are
attached to the furniture properly and kept tightened.
ASSEMBLY INSTRUCTIONS
BD3001CKHN/KHN
BD3001CKFN/KFN
BD3001KRN
Thank you for purchasing this quality product. Please read the instructions thoroughly before unpacking the assembly parts.
Caution: sharp exposed staple tips can cause injury, therefore for your protection, please remove any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
5. Please lay all parts and hardware on a non abrasive surface such as a carpet, and follow the assembly steps.
DESCRIPTION
Hardware List:
Components List:
STEP 1:
Lay the Headboard (C) front side down on a smooth and clean
surface.
Attach HB Left Leg (A) and HB Right Leg (B) to Headboard (C) using
Flat Washer (4), Spring Washer (3), Bolt (2). Do not fully tighten yet.
Attach Wood Stretcher (D) to HB Left (A) and HB Right legs (B) using
Flat Washer (4), Spring Washer (3
), Bolt (2), fully tighten with Allen
Key (1).
Fully tighten all the bolts located in HB Left Leg (A) and HB Right Leg
(B).
FIG 1
(C)
(A)
(D)
(B)

PROD. NO.:
Page 2 of 2 MADE IN VIETNAM
WINNERS ONLY ®
ASSEMBLY INSTRUCTIONS
BD3001CKHN/KHN
BD3001CKFN/KFN
BD3001KRN
FIG 3
STEP 2: Hook both Side Rails (F) to the
Headboard assembly and to the Footboard
(E) as shown in FIG 2.
FIG 2
(F)
(E)
Assembly is now completed.
(F)
(H)
(I)
(C )
(F)
STEP 3: Attach Support Legs (I) to the Slat (H) as shown in
FIG 3.
STEP 4: Attach Slat with Support Legs (I&H) to the Side
Rails (F) using Screws (5) as shown in FIG 3.