HBF Furniture LOGIC User manual

GENERAL NOTES
1. ALWAYS PROTECT THE WORKSURFACE DURING INSTALLATION.
2. ALWAYS LEVEL UNIT(S) AT FINAL LOCATION.
3. TWO PERSON ASSEMBLY REQUIRED
B1013-0004-00
PAGE 1
ASSEMBLY INSTRUCTIONS
LOGIC CONFERENCE TABLE
HBF
HARDWARE
1 INSTALL GLIDES
2 ATTACH WIRE MANAGEMENT CLIPS
-THREAD IN ALL ADJUSTABLE GLIDES (A)
INTO BASE GLIDE HOLES
-SLIDE EQUAL NUMBER OF WIRE MANAGERS (B)
INTO THE INSIDE OF EACH SUPPORT RAIL
1 1/2 FLAT MACHINE
HEAD SCREW
BLACK CONNECTOR
BOLT
3/4" FLAT
HEAD SCREW
1 1/8 GLIDE JOINT CONNECTOR
DETAIL A
DETAIL B
SPLINE
AB
C
DEF
WIRE MANAGER
GHJ
THUMB SCREW
3/4" PAN
HEAD SCREW
SEE DETAIL B
SEE DETAIL A

B1013-0004-00
PAGE 2
LOGIC CONFERENCE TABLE
HBF
5 INSTALL SPLINES
-INSERT SPLINES (E) IN ONE GROOVE OF EACH JOINT
-PLACE TOPS ON THE BASES IN FINAL LOCATION
-SLIDE TOPS TOGETHER ALIGNING THE SPLINES
TO THE GROOVE
3 ATTACH FLAT PLATES TO END OF RAILS
-ALIGN FLAT PLATES WITH MOUNTING HOLES AS SEEN BELOW
-SECURE PLATE TIGHTLY AGAINST END OF RAIL WITH FLAT HEAD 1 1/2" MACHINE SCREWS (C)
-MAKE SURE TO PROPERLY ALIGN THE ALUMINUM EXTRUSIONS TO FULLY CLOSE GAPS
-REPEAT THIS PROCESS TO SECURE REMAINING FLAT PLATES TO RAIL ENDS
SPLINE
NOTE:
DO NOT LIFT TOP ONCE JOINT FASTENERS ARE
INSTALLED. UNEVEN LIFTING WILL PINCH THE
TOP VENEER AT THE SEAM CAUSING A BUBBLE
IN THE VENEER.
DETAIL C
4 ATTACH FLAT PLATE TO BASES
-ALIGN TWO RAIL WITH SIDES OF BASES
-SECURE FLATPLATE TO BASE USING BLACK CONNECTOR BOLTS (D)
-MAKE SURE TO PROPERLY ALIGN THE PLATE TO THE BASE TO FULLY CLOSE GAPS
-REPEAT THIS PROCESS UNTIL ALL RAIL ARE FASTENED TO BASES
GROOVE
SEE DETAIL C
SEE DETAIL D

B1013-0004-00
PAGE 3
LOGIC CONFERENCE TABLE
HBF
8 SECURE RAILS TO WORKSURFACE
-SECURE RAILS TO WORKSURFACE USING
THE MOUNTING HOLES IN THE RAILS
WITH 3/4" PAN HEAD
SCREWS (H)
-DO THIS FOR ALL RAILS
7 SECURE WORKSURFACE TO BASES
-CENTER TOP ON BASES
-ALIGN LOCATION HOLES ON BOTTOM
OF WORKSURFACE TO OUTER SCREW
HOLE IN THE BASE FLAT PLATES
-INSTALL ONE 3/4" FLAT HEAD
SCREW (G) IN EACH
CORNER TO ENSURE PROPER
ALIGNMENT
-ONCE ALIGNED, FINISH SECURING
FLAT PLATES TO WORKSURFACE DETAIL E
6 ALIGN AND SECURE WORKSURFACE
-INSTALL ONE JOINT CONNECTOR (F) ON EACH END OF
JOINT TO ENSURE PROPER ALIGNMENT
-INSTALL REMAINING JOINT CONNECTORS
NOTE: TOP WILL HAVE TO BE MOVED FROM SIDE TO SIDE
SLIGHTLY IN ORDER TO INSTALL ALL JOINT CONNECTORS
NOTE: ALWAYS INSTALL THE TOP RIGHT
SIDE UP ON TOP OF THE BASES. USE
SAWHORSES IF NECESSARY TO SUPPORT
THE TOP BEFORE THE BASES ARE ATTACHED.
9 INSTALL BOTTOM PANEL
(FOR WIRE MANANAGEMENT)
-SECURE BOTTOM PANEL TO UNDERSIDE OF THE UNDERSIDE
OF THE SIDERAILS USING THUMB SCREW (J)
10 ADJUST GLIDES TO LEVEL TABLE
DETAIL F
DETAIL G
SEE DETAIL E
SEE DETAIL F
SEE DETAIL G