HDanywhere MHUB User manual

QUICK START GUIDE
FULL MANUAL ON SUPPORT.HDANYWHERE.COM
1Connect a HDMI source device (e.g Satellite/Cable TV, Apple TV, Blu-ray, DVD
etc) to one of the ports labelled “SOURCE INPUT” on the MHUB chassis using
a good quality HDMI cable.
The steps below describe how to connect a single HDMI source to a display location for outputs 1-3 and enable remote control (IR) signals to be sent from that location back to your
MHUB chassis. If you want to setup IR control on output 4, please refer to the product manual. Repeat the steps below as necessary for each source or display.
2Connect a CAT cable between one of the HDBaseT output ports (labelled A, B,
C) on the MHUB chassis, and the “HDBASET” port on the MHUB receiver.
3Connect a HDMI cable between the port labelled “HDMI OUT” on the MHUB
receiver and a HDMI port on your display. Ensure that your display is switched
to the correct input. Note: MHUB receivers do not need any power cables to
work, power is delivered from the MHUB chassis. Check the white LED light on
the MHUB receiver is lit, this indicates a connection with the MHUB chassis.
Check that you are receiving a picture on the connected display.
4
6
5
To control your HDMI source from your display location, connect an IR TX to the
“SOURCE IR (OUT)” port on the MHUB chassis, that matches the “SOURCE
INPUT” port number for the source you want to control. Connect an IR RX to the
“IR (IN)” port on the MHUB receiver.
Test the IR control is working by using the source device remote pointed
towards the IR receiver at your display location.
Connect the “HUB CONTROL IP” port to your router via an ethernet cable. You
can then download our uControl app which is available for iOS and Android. The
uControl App will also provide your MHUB IP address.
HDMI CABLE
CAT6 CABLE
INFRARED (IR) CABLE
NETWORK CABLE
POWER
1
6
23
4
5
CAT6 RESOLUTION/DISTANCE GUIDE
0m
0ft 10m 32ft 20m 65ft 30m 98ft 40m 131ft 50m 164ft 60m 197ft 70m 230ft
HD UHD
IN THE BOX
1x IEC POWER CABLE + 24V PSU
1x MHUB 4K (4X3+1) CHASSIS
3x MHUB RECEIVERS + 6x MOUNTING WINGS 1x REMOTE CONTROL
INFRARED (IR) CABLES
2x CHASSIS
MOUNTING BRACKETS
4x IR RX
4x IR TX
INPUTS
OUTPUTS
menu
1 2
3 4
A
ALL
CLEAR OK
EDID
B
C D
1
2
3
4
A
1
2
3
4
B
1
2
3
4
C
1
2
3
4
D
1
2
3
4
A
1
2
3
4
B
1
2
3
4
C
1
2
3
4
D

PORTS & LABELS
FULL MANUAL ON SUPPORT.HDANYWHERE.COM
“SOURCE INPUTS” [1-4]: Use to connect HDMI
source devices to the MHUB
“SOURCE IR (OUT)” [1-4]: Connect IR TXs to these
ports to control your source devices via IR. The
“SOURCE IR” port number corresponds with the
source input number
“DISPLAY IR (IN)” [1-3]: Connect IR RXs to these
ports to control your displays via IR with a third
party control system
“HUB IR (IN)”: Connect an IR RX to this port to
control your MHUB via IR locally
“AVR IR (OUT)”: If you have an AVR in your system,
connect an IR TX to this port and place it on the IR
window of your AVR
HDBaseT Outputs [A-C]: Connect your MHUB
receivers to these ports via a CAT cable
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
HDMI Output [D]: Connect a display to this port via
a HDMI cable
“DIGITAL” Audio [D]: Use this port to extract
multi-channel audio via a toslink cable from output
[D]
“STEREO” Audio [D]: Use these ports to extract
stereo audio via a left and right phono cable from
output [D]
“HUB CONTROL IP” Port: Connect the MHUB
system to your router via this port to enable DASH
features and IP control from the uControl App
“HUB CONTROL RS232” Port: Use to integrate your
MHUB with a control system via RS232
DC 24V: Plug the 24V DC power supply into the unit.
Power LED: If this is lit up your matrix is receiving
power
Source Selector [1-4]: Select which source you
want to switch to via the button
USB port: Used to manually firmware update your
MHUB.
1
2
3
Power LED: This LED indicates that the receiver
has a PoE connection with the matrix
“HDBASET”: Connects back to the HDBaseT output
on the MHUB chassis
“HDMI OUT”: Connect this to your local display
using a HDMI cable
4“IR (IN)” and “IR (OUT)”: Connect an IR RX to the ‘IR (IN)” port to
send IR commands back to the MHUB chassis, Connect an IR TX
to the “IR (OUT)” port to enable control of your display
MHUB 4K (4X3+1) CHASSIS (REAR) MHUB 4K (4X3+1) MHUB CHASSIS (FRONT)
MHUB 4K (4X3+1) RECEIVER
MHUB RECEIVER
MHUB 4K (4X3+1) CHASSIS (REAR)
MHUB 4K (4X3+1) CHASSIS (FRONT)
1
1
5 7
38
6
9 10
411 12
2
2
OUTIN
1 2 3 4
A B C D
display ir (in) ALL IR (in)HUB ir (in)
source ir (out) AVR IR (OUT)
1 4 A B C D OPTICAL
STEREO
SOURCE INPUT
IP RS232 dc24v
2 3
1
2
3
4
A
1
2
3
4
B
1
2
3
4
C
1
2
3
4
D