HDL HDL-MPT2.46 User manual

Professional Home and Building Automation Do you need help? Contact with us
[e-mail]
www.hdlautomation.com 1/ 2
Parameters
Electric Parameters (from HDL-MPPI.46 ):
BUS Power Supply DC12-30V
BUS Power consumption
(from HDL-MPPI.46) 20mA/DC24V
Environmental Conditions:
Working Temperature -5℃~45℃
Working relative Humidity Up to 90%
Storage Temperature -20℃~+60℃
Storage relative Humidity Up to 93%
Approved
CE
RoHS
Production Information:
Dimensions 86×116.5×10.5 (mm)
Weight MPT2.46:137.5(g); MPT4.46: 143(g)
MPT6.46:
Housing material Glass
Installation US wall box
Protection IP20
Overview
■It must work in conjunction with HDL-MPPI.46.
■Real product may be different from pictures on the right.
■Touch performance –touch panel sensitivity need to be read-
justed after installation.
■IR receiver function –only available for customized touch panel
with IR receiving hole.
■The cover can be replaced by the user .
■Bus cable—HDL Buspro/KNX cable, 0.8mm single-core copper
cable.
■Bus Connection—Series connection (hand-in-hand).
■Installation—US wall box.
Important Notes
Installation Step
■Connect bus cables. Make sure the color of wire complies
with the definition
■Make sure the Bus cable type is correct and has no short
circuit
■Mount the HDL-MPPI.46 in the wall-box
■Put this device into HDL-MPPI.46
HDL - MPT2.46
HDL - MPT4.46
HDL - MPT6.46
■Key Mode: Single on/off, Single on, Single off, Combi-
nation on, Combination off, Combination on/off, Short/
long press, Short press/long press..
■Key Control Type: Scene, Sequence, Timer, Universal
Switch, Single Channel Control, Broadcast Scene,
Broadcast Channel, Curtain Control, GPRS Control,
Panel Control, Security Module, Music Play, Universal
Control, etc.
■Built-in IR receiver, need to replace a plate with an IR
receiving hole to enable the IR remote control function.
■IR remote control function.
■Adjustable backlight color and intensity .
■Support HDL Buspro online upgrading .
■Customized image for touch panel.
Functions
HDL Buspro Definition for Cable
HDL Buspro HDL Buspro/KNX
DC24V Red
COM Black
DATA- White
DATA+ Yellow
Multi-function control panel, embedded with RGB
LED backlight for each touch button, any color is
available for the button via setting in HDL Buspro
configuration tools software.
Safety attention
■The screw down strength should not exceed 0.1Nm
■Mounting position: indoor
■Do not make wrong connection on Bus interface, it
will damage the Bus interface of this module
■Never let liquids get into the module, it will damage
this device
■Do not get AC power into Bus wire , it will damage all
devices in the system
■Ensure good ventilation
■Avoid contact with liquids and aggressive gases
HDL-MPT2.46 HDL-MPT4.46 HDL-MPT6.46

Professional Home and Building Automation Do you need help? Contact with us
[e-mail]
www.hdlautomation.com 2/ 2
Dimensions and Wiring
HDL - MPT2.46
HDL - MPT4.46
HDL - MPT6.46
Installation: Hold the edge of panel (shown as above), insert the power interface module vertically. Do not
push the panel too hard.
Split: Insert a 2.5mm-screwdriver to the split gap, pry up from position 1 to 2,and then the wiring hole will open.
Then separate the panel and MPPI.46.
Glass plate replacement: Insert a small size straight screwdriver into the gap of the left side or right side of glass
cover (shown as above), to pick up the glass cover, then put the new cover in right place , then press the grey
area to lock the cover
Installation
1
2
Separate panel and power interface
Panel Panel power interface
（MPPI.46）
US wall box
Touch button function:On/off, dimming.
Address modification: Press any of button for 15s, all the backlights will flash, the address of this device can be
changed on HDL Buspro software: submenu ”address management→address modify”.
Signal interface and fastener: Connect to panel power interface (MPPI.46).
Split gap: Insert a slotted screwdriver to the split gap, separate the panel and power module (MPPI.46).
MPT6.46MPT4.46MPT2.46
Side view
10.5
Split gap
Signal interface
Fastener
Back view
83.5
Front view
116.5
86