HDTV Supply DTVANI315XLT User manual

HDTVANI315XLT HDTVANI315XLR
HDTVANI315XL
Transmitter & Receiver
HDMI over CAT5e/6 Extender with IR/RS-232
www.HDTVSupply.com
3835-R East Thousand Oaks Blvd. Unit 295
Westlake Village, CA 91362
[phone]
INSTRUCTION MANUAL

SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain
D. The equipment does not appear to operate normally, or exhibits a marked change in performance
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL

TABLE OF CONTENTS
1
CONTENTS
INTRODUCTION & CONTENTS ...................................................1
FEATURES ....................................................................................2
SPECIFICATIONS ........................................................................ 2
OPERATION CONTROLS & FUNCTIONS ...................................3
IR PIN ASSIGNMENT .................................................................. 4
CONNECTION DIAGRAM .......................................................... 5
DEAr CuSTOmEr
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTrODuCTION
The HDMI Extender over single CAT5e/6 incorporating IR and RS-
232 signal transfer allows for a more efcient system setup and is
easy to install.
Uncompressed video and audio can be transmitted to distances of
up to 196 ft (60M) @1080p 115 ft (35M) @4k and supports High
Denition Audio and 3D signals.
Designed with HDBaseT™ technology for greater exibility in
custom installations with full HDMI and control signal transfer over
a single CAT5e/6 cable.
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and
make sure the following items are contained in the shipping carton:
• HDMI over CAT5e/6 Transmitter with IR/RS-232
• HDMI over CAT5e/6 Receiver with IR/RS-232
• IR Blaster
• IR Extender
• 3.5 mm mini-jack to RS-232 female cable
• 3.5 mm mini-jack to RS-232 male cable
• (2) 5V/2.6 A DC Power Adaptor
• Operation Manual
APPLICATIONS
• Residential entertainment sharing and control
• University lecture hall display and control
• Retail sales display and control
• Meeting room presentation and control
• Commercial advertising display and control
SYSTEm rEQuIrEmENTS
HDMI source equipment such as DVD/Blu-ray player/PC and TV/
monitor/projector with HDMI input and HDMI to CAT5e/6 cables.
SAFETY PrECAuTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
DISCLAImErS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYrIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2015. All Rights Reserved.
Version 1.0 AUG 2015
TrADEmArK ACKNOWLEDGmENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

2
FEATurES & SPECIFICATIONS
FEATurES
• HDMI with 3D, 4K2K support, HDCP and DVI compliant
• Complies with the HDBaseT Lite™ class
• Supports HDMI (including HDCP) over a single CAT5e/6 up to 196 ft (60M)
• Full HD resolution support (1080p@60Hz/36-bit), 3D and 4K2K over 131 ft (40M) and PC resolution support (VGA to WUXGA)
over CAT5e/6 cable
• HDMI input cable length up to 50 ft (15M) with 8-bit resolution or 33 feet (10M) with 12-bit resolution
• HDMI output cable length up to 50 ft (15M) with 8/12-bit resolution
• Multiple control interfaces such as RS-232 with baud rate up to 115200/sec and IR
• Supports HDCP repeater and CEC bypass
• Supports High Denition LPCM 7.1CH, Dolby TrueHD, Dolby Digital
• Plus and DTS-HD Master Audio transmission
• Compact size with stylish design)
SPECIFICATIONS
TrANSmITTEr
• Input: 1x HDMI, 1x RS-232
• Output: 1x RJ45, 1x IR Blaster
• Weight: 2oz / 56g
• Power Consumption: 3 W
rECEIvEr
• Input: 1x RJ45, 1x IR Extender
• Output: 1x HDMI, 1x RS-232
• Weight: 2.3oz / 64g
• Power Consumption: 5.5 W
GENErAL
• Video Bandwidth: 300 MHz/10.2 Gbps
• ESD Protection: Human Body Model:
• ±8kV (air-gap discharge)
• ±4kV (contact discharge)
• Power Supply: 2x 5V/2.6 A DC (US/EU standards, CE/FCC/UL certied)
• Dimensions (WxDxH): 2.1 x 3.3 x .9 In (55x82x22.5mm)
• Chassis Material: Plastic
• Silkscreen Color: White
• Operating Temperature: 32˚F~104˚F (0˚C~40˚C)
• Storage Temperature: −4˚F~140˚F (−20˚C~60˚C)
• Relative Humidity: 20~90 % RH (non-condensing)
As product improvements are continuous, specications are subject to change without notice.

3
OPErATION CONTrOLS & FuNCTIONS
TrANSmITTEr FrONT & rEAr PANELS
qIR OUT/Blaster: Connect to the supplied IR blaster for IR signal transmission to the source equipment. Place the IR blaster in direct
line-of-sight of the equipment to be controlled.
wHDMI IN: Connect to the HDMI input source devices such as a DVD player or a Set-top Box with HDMI cable or DVI to HDMI cable.
eRS-232 IN: Connect the 3.5mm mini-jack to D-Sub 9-pin female adaptor cable (included in the package) to a PC or laptop for the
transmission of RS-232 commands.
rDC 5V: Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet.
tCAT5e/6 OUT: Connect to the receiver unit with a single CAT5e/6 cable for transmission of all data signals.
rECEIvEr FrONT & rEAr PANELS
qDC 5V: Plug the 5V DC power supply into the unit and connect the adaptor to an AC outlet.
wCAT5e/6 IN: Connect to the transmitter unit with a single CAT5e/6 cable for transmission of all data signals.
eIR IN/Extender: Connect to the supplied IR extender cable for IR signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR extender.
rHDMI OUT: Connect to a HDMI equipped TV/monitor for display of the HDMI input source signal.
tRS-232 OUT: Connect the 3.5mm mini-jack to D-Sub 9-pin male adaptor cable (included in the package) to a PC or control system
with D-Sub 9-pin cable for the transmission of RS-232 commands.
q ew r t
q ew r t

4
OPErATION CONTrOLS & FuNCTIONS
TrANSmITTEr AND rECEIvEr TOP PANELS
q LINK LED: This LED will illuminate blue when the devices are connected with a CAT5e/6 cable. If the data transmission has an error
the LED will blink.
Ir PIN ASSIGNmENT
D-SuB 9-PIN DEFINITIONS
PIN DEFINITIONS PIN DEFINITIONS
1 N/C 6 N/C
2 TxD/RxD 7 N/C
3 RxD/TxD 8 N/C
4 N/C 9 N/C
5 GND
q
w
e
Power 5V
IR Blaster Signal
NC
q
w
e
IR Signal
Power 5V
Ground
IR Receiver
IR Blaster

5
CONNECTION DIAGrAm
CONNECTION DIAGrAm

END OF DOCUMENT
6
END OF DOCumENT
TErmS AND CONDITIONS OF uSE
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER HDTV Supply, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to HDTV Supply, Inc.
at the return address set forth on the Product’s packing label at your expense. HDTV Supply, Inc. may modify these Terms and Conditions at anytime, without
notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless HDTV Supply, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to HDTV Supply. Any intellectual property rights pertaining to the Product are
licensed to you by HDTV Supply, Inc. and/or its afliates, including any manufacturers or distributors of the Product (collectively, “HDTV Supply”) for your personal
use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by HDTV Supply for your personal use only. HDTV
Supply does not transfer either the title or the intellectual property rights to the Product and HDTV Supply retains full and complete title to the intellectual property
rights therein. All trademarks and logos are owned by HDTV Supply or its licensors and providers of the Product, and you may not copy or use them in any manner
without the prior written consent of HDTV Supply, which consent may be withheld at the sole discretion of HDTV Supply.
The functionality and usability of the Product is controlled by HDTV Supply, Inc. from its ofces within the State of California, United States of America. HDTV
Supply makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you
provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.
Disclaimers and Limitation of Liability
HDTV Supply may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS”AND WITHOUT WARRANTIES OFANY KIND EITHER EXPRESS OR IMPLIED. HDTV SUPPLY DOES NOT WARRANT OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
HDTV Supply has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be
relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies
or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, HDTV SUPPLY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
HDTV SUPPLY DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
HDTV SUPPLY DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
HDTV SUPPLY WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT
TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT HDTV SUPPLY) ASSUME THE ENTIRE COST OF ALL
NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY HDTV
SUPPLY.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL HDTV SUPPLY BE LIABLE FORANY SPECIALOR CONSEQUENTIAL
DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF HDTV
SUPPLY OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL HDTV SUPPLY’S TOTAL
LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU
PAID TO HDTV SUPPLY, IF ANY, FOR THE PRODUCT.