HE Slushie Stars User manual

Slushie Stars
(MODEL #19275-0001)
OPERATORS MANUAL V1.2
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

INDEX
Section Sub Section Page Number
1. Safet Instructions 3
2. Introduction 2.1. Quick Start 4
3. Product Description 3.1. Product Overview 5
3.2. Product Specifications 5
4. Control Panel & Functions 4.1. Panel Diagram 6
4.2. Set Parameters 6
4.3. Introduction to Functions 7
4.4. Temperature Range & Default Settings 7
5. Operation 5.1. Drink Preparation
5.2. Making Slushie Drinks 9
5.2.1 - Family Slushie Mixes 9
5.2.2 - Adult Slushie Mixes 10
5.3 Making Cold Drinks 11
5.4 Drink Dispensing 11
6. Disassembl , Cleaning &
Assembl
6.1. Disassembly 12
6.2 Cleaning 13
6.3. Re-Assembly 13
7. Deep Settings & Error Codes 7.1. Deep Settings 14
7.2. Alarm Codes 15
8. Spare Parts 16
8. Warrant & Contact Details 16
- 2 -
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

IMPORTANT
Please read all SAFETY PRECAUTIONS and INSTALLATION sections before
operating machine. Please keep instructions.
1.SAFETY INSTRUCTIONS______________________________________________________
Safety instructions apply to operators and service personnel. Read and follow all instructions carefully, and
heed all warnings. Other safety instructions may appear elsewhere in this manual.
This is not a toy – please take care with the operation of the machine and do not allow access to
the inside of the machine which has HIGH VOLTAGE.
Protect the power chord from being walked on, pinched or damaged in any way. If cable becomes
damaged, please replace immediately.
Mount machine on stable surface. Using the machine on un-even surface is to be avoided at all
times. There is risk that the machine will topple over, but also, the machine needs flat surface for
the mixing cylinder to operate.
Do not spray rinse the machine. Please check cleaning guidelines.
Do not use solvent or other cleaning substances.
Before cleaning the machine, make sure the machine has been disconnected from the power.
Do not block ventilation openings.
Syrup must be premixed with water before starting the machine. Mixing Syrup only in this machine
may cause your motor to jam, damage your machine and void your warranty.
The machine must be repaired by our service centre or a trained technician. Unauthorised
servicing of the machine by the user is not allowed.
Do not use the machine near water. To reduce the risks of fire or electrical shock do not expose the
machine to rain, moisture, dripping or splashing. Leaving the machine outside on balconies,
carports or exposed to outdoor weather will significantly reduce the life of the machine.
Damage due to improper operation or unauthorised modifications will void our warranty
Do not use the machine in case any of its components is damaged. Please call our service centre
for help on 02 496 9313.
- 3 -
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

2. Introduction_____________________________________________
Thank you for purchasing our Slushie Stars 15L Slushie machine.
Please take a moment to read this manual and understand all the features of this machine which you can
customise to suit your venue or home.
This machine is suitable for;
Cold Drink Dispensing
Slushie Drinks & Cocktails
2.1 Quick Start
1. Please check Section 6 (Disassembly, Cleaning & Assembly Section) for dismantling, cleaning and
reassembly of you machine for first time use.
2. Please read Section 5 (Operations) where it will show step by step on how to add your syrup/drink
mix, temperature settings and operations.
It’s very important you follow any hints and warnings to avoid damaging your machine, and to maximise
the benefits of the Slushie/Drinks machine.
Please feel free to call our office, follow our social media where we will post helpful hints, and view videos
on our Youtube channel below;
https://www. outube.com/c/highwa arcade/videos
-4-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

3. Product Description & Specifications_________________________
3.1 Product Overview
The main components of the machine are as
follows:
1. Tank Lid
2. Tank
3. Dispenser Lever
4. Dispenser
5. Control Panel
6. Machine Chassis
7. Waste Tray
Specifications
Model Name & Number: Slushie Stars 15L Model #19275-001
Assembled Size L x B x H (cm): D52cm x W21cm x H 0cm
Packing Size L x B x H (cm): L59cm x W34cm x H101cm
Net Weight: 31kgs
Gross Weight: 47kgs
Tank Size 15 Litres
Climate Type: SN
Electronic Safety Type: I
Refridgeration: R290 / 70g
Sound Level: 70 dB
Operating Temperature: 10 – 40 degrees
Power: 240volts ~ 50Hz ~ 500W
-5-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

4. Control Panel Description & Function_________________________
4.1 Panel Diagram
1. Current Temperature 5 Cold Drink Button Indicator 9 Slush Button
2 Wanted Temperature 6 Cold Drink Button 10 Slush Button Indicator
3 Mixing Button LED Indicator 7 Set/ Subtract Button 11 Lighting Button
4 Mixing Button Add Button 12 Lighting Button Indicator
4.2 Set Parameters
Press “Set” button to enter the user adjustment setting state.
Press “+” button to increase the value.
Press “-“ button to lower the value .
After 5 seconds without any press/adjustment, the system will exit and save the setting value
automatically.
Please view section 5.2 an 5.3 for temperature settings for Slushie/Drinks.
-6-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

4.3 Introduction to Function
Function Description Indicator
Press Mixing Button Turns on mixing function Mixing light is on
Press Mixing Button Again Turns off mixing function Mixing light is off
Press the Cold Drink Button
(Mixing function must be turned on,
otherwise the Cold Drink function
does not work)
Turns on the cold drink function Cold drink light is on
Press the Slush Button
(Mixing function must be turned on,
otherwise the Slush function does
not work)
Turns on the slush function Slush light is on (the compressor is
powered on)
press the Slush Button Again Turns off the slush function Slush light flashes or off (compressor
is powered off)
Press the Lighting Button Turns on the light Lighting in tank is turned on
press the Lighting ke again Turns off the light Lighting in tank is turned off
4.4 Temperature Range & Default Settings
PARAMETER FUNCTION TEMPERATURE RANGE
Slush Temperature -9.0 ~ -1.9
Cold Drink Temperature 1.0 ~ 10.0
Above are the temperature settings available. Default settings are;
-2.0 degrees for Slushie Drinks
5.0 degrees for Cold Drinks
-7-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

5. Operations______________________________________________
Please choose a flat and firm mounting position. If your base is not level or unstable, it will dramatically
influence the Slushie machine’s function.
Please also check that the machine is fully assembled well before adding liquid, especially that the tank is
seated properly into the machine chassis (photo above). And that you have lubricated the seals.
Warnings; - Never add hot liquid to your Slushie machine
- Be careful not to exceed the Tank limit height
- Do not allow undiluted syrup or final mix to exceed 13% sugar content as this will jam
the motor of the slushie machine once the liquid cools
5.1 Drink Preparation
Lift the Tank Lid and pour in your water, syrup (and for cocktails, alcohol) taking note of the maximum
limit of the Tank.
Warning: Never leave syrup or high sugar content liquids to be used in raw form. Once they begin to
cool/freeze, they will solidify and jam the cylinder motor and cause damage to your
machine voiding your warranty. Always add water to your mix before the cooling process.
- -
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

Please follow the above guide for liquid levels in your machine.
5.2 Making Slushie Drinks
Everyone’s tastes are slightly different, and we recommend you trial different mixes, temperatures, and
flavours to match your tastes and slush consistency.
If you have purchased our Slushie Syrup, we recommend you use the 2 Litre plastic bottle for your
measuring (and storage);
5.2.1 Family Slushie Mixes
a) Pour the 2 litre syrup flavour into the Tank
b) Use the empty 2 litre bottle, and fill with water x 4 times
and pour into the Tank
-9-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

Machine Setup (after pouring liquid and turning machine on);
1. Press the Mixing Button
2. Press the Slush Button
3. To change temperature, press the Set button, and use the +/- to adjust
Default Temperature is -2.0 degrees.
Please Note: Machine will save your previous use temperature settings.
Hint: Keep the 2 Litre empty bottles and fill and pre-cool the water in you fridge. Or, use cold
water when filling the tank. This will shorten the time needed to create your slushie drinks.
5.2.2 Adult Slushie Mixes
a) Pour the 2 litre syrup flavour into the Tank
b) Use the empty 2 litre bottle, and fill with water x 4
times and pour into the Tank
c) Pour your alcohol into the Tank
Machine Setup (after pouring liquid and turning machine on);
1. Press the Mixing Button
2. Press the Slush Button
3. To change temperature, press the Set button, and use the +/- to adjust
Default Temperature is -2.0 degrees.
Please Note: Depending on the volume of alcohol and alcohol content, you may need to adjust the
temperature to a lower setting. Take notes, as each cocktail mix may have variable/optimal
temperature depending on your personal tastes.
Machine will save your previous use temperature settings.
-10-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

5.3 Making Cold Drinks
Pour your favour juice/drink/cordial into the tank, but take special care to never leave concentrate/high
sugar (more than 13%) in your machine, and always premix with water if necessary.
Or, use your Slushie machine for cold water dispenser.
Machine Setup (after pouring liquid and turning machine on);
1. Press the Mixing Button
2. Press the Cold Drink Button
3. To change temperature, press the Set button, and use the +/- to adjust
Default Temperature is 5.0 degrees.
Please Note: Machine will save your previous use temperature settings.
5.4 Drinks Dispensing
This machine allows drinks to be dispensed either by pushing or pulling the level.
-11-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

6. Disassembl , Cleaning & Assembl ___________________________
6.1 Disassembl
Warning: (a) Please disconnect the machine from power before Disassembly
(b) Please remove all liquid before disassembly
Step 1 Remove the Tank Lid
Step 2 Push the Tank gently forward/upwards to Step 3 Gently slide out the tank
release the plastic legs that hold the Tank to
the machine chassis.
Step 4 Gently slide out the mixer. Step 5 Disassembly the Push handle
Put the Tank on a smooth surface to easily remove the tap.
Push the tap with your hand. Slide the Unlock Pin out of
its housing to release it.
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

6.2 Cleaning
Once parts are dismantled, wash all parts thoroughly with non-corrosive cleaner and warm water, then air
dry or wipe down with soft cloth.
Warning: Do not submerge Tank Lid in water, as the lighting globe is inside the Lid. Please clean the
lid with sponge and wipe dry.
Wipe down metal cylinder and run warm water in the water flow found in the machine chassis. This will
clean the internal house that fills the waste tray. Clean the waste tray and grid separately with warm
water.
Wipe off old lubricant and re-seal with new lubricant (please review Section 6.3.1).
Once machine is fully assembled, fill the Tank with water and run for 5 minutes, remove all water, and fill
with your syrup and water.
6.3 Re-Assembl
Assembly instructions are the reverse order of 6.1 Disassembly.
Hint: Please lubricate seals for better efficiency.
Care should be taken with the following steps;
1. The seal ring (A) of the mixer shaft needs to be installed (please use Food Grade Silicon to lubricate
the seal). The lubricant is on the outside of the seal which then connects to the metal cylinder.
Always check the integrity of the seal ring. If the seal ring is broken, it should be replaced with a
new one.
2.
Install the mixer shaft as shown; install the head of the mixer shaft (C) to the shaft (D)
Rotate it into the first half of the Tank and push the Tank to the designated position in contact with
the seal ring (B)
-13-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

3. Align the head of the mixer shaft with the interface inside the Tank, press down the Tank until it
sits well in place in the machine chassis. Please make sure the seal (B) is tight and well seated.
4. After assembly, perform a Rinse Cycle by filling the tank and running for 5 minutes. Empty the
water in the tank and fill with your syrup/water mix.
Warning: the tank and parts must sit perfectly in position. If they are not seated properly, liquid can
leak, and Slushie machine’s function will be limited.
7. Deep Settings & Error Codes ________________________________
7.1 Deep Settings
Your slushie machine has already been set on the optimum settings. This section should be used with
care.
- Hold down “SET” button and “ADD” button together for 10 seconds at the same time
- Press “LIGHTING” to choose parameters
- Press “SET” or “ADD” to make changes to the values
- The system will exist and save the settings after 10 seconds of non use
-14-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

PARAMETER FUNCTION RANGE
P1 Slush temperature return difference
value
0.3 (Degrees)
P2 Slush middle position corresponds to
temperature
-2.0 (Degrees)
P3 Slush position number 20 (Position)
P Press protection time 5 (Minutes)
P5 Low voltage protection value 187（V）
P6 1 (0: Disable 1: Enable) Voltage protection enabled
P7 Tank temperature correction 0.0
P8 Not used 0.0
PA Cold drink temperature return
difference value
2.0 (Degrees)
PB Cooling stop speed 230.(230.stands for 2300 rotations)
7.2 Alarm Codes
ALARM CODE DESCRIPTION
Frozen Tank alarm.
The compressor and motor will stop working, and resume automatically
after 10 minutes.
Temperature sensor malfunction alarm.
Stop cooling in cold drink function state without affecting slush function.
Low voltage alarm.
The machine stops. Cut off the Power to repair the machine.
-15-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]

8. Spare Parts______________________________________________
For current spare parts list, please visit;
www.slushiestars.com.au
www.highwa .net.au
We carry all major parts as stock items in our warehouse.
9. Warrant Polic & Contact Details___________________________
ALL components are covered by Highway Entertainment’s 12 months unlimited (worry free) warranty,
which means that you can operate this machine commercially or in your home and should anything go
wrong, we will provide parts to solve (at our cost including transport to you).
If the machine cannot be repaired, we will arrange our technician to visit your premises and repair
immediately, or, we will pick up the machine, repair and send back to you (at our cost).
Of course, if you have left the machine on the back verandah or in your beer garden and the machine has
been exposed to neglect or allowing the machine to freeze over/adding syrup only and therefore
damaging the cylinder/motor – we will help you get everything fixed, but will not cover the costs. Rough
handling and breakages due to machine abuse will also not be covered.
To make any warranty claim, please call our service centre on 02 496 9313, have your invoice number
ready together with the problem with the machine, and one of our team will solve the problem quickly.
We are here to help.
Alternatively, please choose;
To visit our showroom/warehouse Make warranty claim online, please visit
Highway Entertainment www.highway.net.au/warranty
44-4 Maitland Road
Mayfield, NSW, 2304, Australia
Phone [phone]
Fax [phone]
Email: [email protected]
Highway Entertainment values your feedback, as we want to continue to improve the quality of the
machines we offer. Please give us your feedback (whether good or bad) to www.highway.net.au/feedback
Thank you for your support.
-16-
Highway Entertainment, 44-4 Maitland Road, Mayfield East, 2304, NSW, Australia.
Phone: [phone]. Fax [phone]. Email: [email protected]