Heat & Glo COSMO-I30AU User manual
1Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
Models:
COSMO-I30AU
Owner’s Manual
Installation and Operation
DO NOT DISCARD THIS MANUAL
NOTICE
• Leave this manual with
partyresponsibleforuse
andoperation.
DONOT
DISCARD
• Important operating
and maintenance
instructionsincluded.
• Read,understandandfollow
theseinstructionsforsafe
installationandoperation.
SAI Global
Ref No GSCS20181
AS4553: 2008
• DO NOT USE OR STORE FLAMMABLE
MATERIALSNEARTHISAPPLIANCE.
• DO NOTSPRAYAEROSOLSINTHEVICIN-
ITY OFTHISAPPLIANCE WHILE IT IS IN
OPERATION.
- DO NOTtrytolightanyappliance.
- DO NOT touch any electrical switch. DO
NOTuseanyphoneinyourbuilding.
- Immediatelycallyourgassupplierfroma
neighbor’sphone.Followthegassupplier’s
instructions.
- Ifyoucannotreachyourgassupplier,call
theredepartment.
• Installation and service must be performed
byaqualiedinstaller,serviceagency,orthe
gassupplier.
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrierisnotpresentorhelpisneededtoproperlyinstallone.
HOT SURFACES!
Glassandothersurfacesarehotduring
operationANDcooldown.
• DO NOTtouchglassuntilitiscooled
• NEVERallowchildrentotouchglass
• Keepchildrenaway
• CAREFULLY SUPERVISE children in same room as
replace.
• Alertchildrenandadultstohazardsofhightemperatures.
PLACE ARTICLES ON OR AGAINST THIS
APPLIANCE.
• Keep clothing, furniture, draperies and other ammable
materialsaway.
WARNING! DO NOT modify this appliance.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 2
MODELS: COSMO-I30AU
ARE SAI GLOBAL APPROVED FOR NATU-
RAL GAS AND PROPANE AS A BALANCED
Refer to the appliance data plates for gas
consumptionsandpressures.
Installationofthisapplianceshouldonlybecar-
riedoutbyanauthorizedpersoninaccordance
withthemanufacturer’sinstructions.Appliance
is to be installed in full compliance with the
National Gas Installation StandardAS5601,
themanufacturer’sinstructions,andanylocal
authorities’requirementsforgas,electricaland
buildingregulations.
Thisapplianceanditscomponentsaretested
andsafewheninstalledinaccordancewiththis
InstallationManual.Reporttoyourdealerany
partsdamagedinshipment,specicallycheck
glasscondition.Thegaslogsanduesystem
componentsareinseparatepackages.Read
allinstructionsbeforestartinginstallationand
followtheseinstructionscarefullyduringinstal-
lationtoensuremaximumbenetandsafety.
Failuretofollowthemwillvoidyourwarranty
andmaypresentarehazard.
TheHeat&Glo,abrandofHearth&Home
Technologieswarrantywillbevoidedby,and
Heat&Glo,abrandofHearth&HomeTech-
nologiesdisclaimsanyresponsibilityfor the
followingactions:
• Installationof anydamaged heateror ue
systemcomponent
• Modicationoftheheaterorbalancedue
systeminstallationotherthanasinstructed
byHeat&Glo,abrandofHearth&Home
Technologies.
• Improperpositioningofthegaslogsorthe
glassdoor.
•Installation and/or use of any component
partnotmanufacturedorapprovedbyHeat
&Glo,brandofHearth&HomeTechnolo-
gies, not withstanding any independent
testinglaboratoryorotherpartyapproval
ofsuchcomponentpartoraccessory.
PLEASEREADTHISMANUALBEFOREINSTALLING
ANDUSINGTHISAPPLIANCE.
IMPORTANT: Read all instructions carefully before starting installation.
Failuretofollowtheseinstallationinstructionsmayresultinapossiblere
hazardandwillvoidthewarranty.Savethismanualforfuturereference.
Heat&Glo,abrandofHearth&HomeTechnologies
7571215thStreetWest,Lakeville,MN55044
Copyright2014•PrintedinU.S.A.
3Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
ModelName:___________________________________________ Datepurchased/installed:__________________
SerialNumber:__________________________________________ Locationonreplace:_____________________
Dealershippurchasedfrom: _______________________________ DealerPhone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
CongratulationsonselectingaHeat&Glogasreplace,an
elegantandcleanalternativetowoodburningreplaces.
TheHeat&Glogasreplaceyouhaveselectedisdesigned
toprovidetheutmostinsafety,reliability,andefciency.
Astheownerofanewreplace,you’llwanttoreadand
carefully follow all of the instructions contained in this
Owner’s Manual.Payspecialattentiontoallcautionsand
warnings.
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
importantdocumentsandproductmanuals.
TheinformationcontainedinthisOwner’s Manual,unless
noted otherwise, applies to all models and gas control
systems.
YournewHeat&Glogasreplacewillgiveyouyearsof
durableuseandtrouble-freeenjoyment.Welcometothe
Heat&Glofamilyofreplaceproducts!
We recommend that you record the following pertinent
information about your replace.
Themodelinformationregardingyourspecicreplacecanbefoundonthe
ratingplateusuallylocatedinthecontrolareaofthereplace.
Readthismanualbeforeinstallingoroperatingthisappliance.
Pleaseretainthisowner’smanualforfuturereference.
SerialNumber
TypeofGas
ModelNumber
SAMPLE
SAI Global Certification Nº:
DMS (mm)
xxxx-xxx
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 4
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
A. Congratulations .................................3
B. LimitedLifetimeWarranty..........................5
A. ApplianceCertication............................8
B. GasPressureRequirements....................... 8
C. HighAltitudeInstallations..........................8
D. Non-CombustibleMaterialsSpecication..............8
E. CombustibleMaterialsSpecication .................8
F. ElectricalCodes.................................8
User Guide
A. GasFireplaceSafety............................. 9
B. YourFireplace .................................. 9
C. ClearSpace...................................10
D. DecorativeDoors,FrontsandSurrounds............. 10
E. FixedGlassAssembly ...........................10
F. RemoteControls,WallControlsandWallSwitches.....10
G.IPIBatteryTray/BatteryInstallation.................10
H. ControlModuleOperation ........................10
I. BeforeLightingFireplace......................... 11
J. LightingInstructions(IPI).........................12
K. AfterApplianceisLit.............................13
K. FrequentlyAskedQuestions ......................13
A. MaintenanceTasks-Homeowner ...................14
B. MaintenanceTasks-ServiceTechnician.............. 15
Installer Guide
A. TypicalApplianceSystem.........................16
B. DesignandInstallationConsiderations.............. 17
C. ToolsandSuppliesNeeded.......................17
D. InspectApplianceandComponents.................17
A. MinimumFireplaceOpening ......................18
B. MantelandWallProjections.......................20
A. VentTerminationMinimumClearances..............21
7 Installation Preparation
A. InspectionandCleaning.......................... 22
B. FlueDamper...................................22
C. GasLine......................................22
D. FireplaceConversionNotice ......................22
E. ElectricalOutletBox.............................22
F. RemoteControl ................................22
A. VentLimits....................................23
B. VentingComponents ............................23
C. ConnectingVentPipe............................23
D. Placing,SecuringandLevelingtheAppliance ........25
E. InstallingAdaptorandTerminationCap.............. 26
F. VentKitsComponents...........................29
G.Alternate Venting Congurations UsingAdaptation to SLP
Venting: ......................................29
H.FlueTermination................................30
I. HeatShieldRequirementsforHorizontalTermination...30
A. GasPressureRequirements...................... 37
B. GasConnection................................37
A. WiringRequirements............................ 38
B. IntelliFirePlusTMIgnitionSystemWiring.............. 38
C. OptionalAccessoriesRequirements ................39
D. REM300-HNG-AUInstructions.....................40
A. MantelandWallProjections.......................47
12 Appliance Setup
A. RemoveGlassAssembly.........................48
B. RemovetheShippingMaterials....................48
C. CleantheAppliance.............................48
D. Accessories...................................48
E. GlassPanelInstructions..........................48
F.MediaInstructions...............................48
G.FixedGlassAssembly ...........................49
H. AirShutterSetting ..............................49
I. DecorativeFrontsandSurrounds ..................50
J. OptionalAccessories............................51
A. IntelliFirePlus™IgnitionSystem...................52
B.MaintenanceTasks .............................54
14 Reference Materials
A. ApplianceDimensionDiagram.....................55
B. ServiceParts..................................56
C. ContactInformation............................. 59
=Containsupdatedinformation.
5Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
AUSTRALIAN WARRANTY INFORMATION
Warranty information in the attached manual is for international markets,
not Australia. For Australian warranty information, please see below.
Hearth & Home Technologies (HHT)
7571 215th Street West, Lakeville, MN 55044
0011-1-651-345-1777
www.heatnglo.com
HHT extends the following manufacturer’s warranty for HHT gas, wood, pellet, coal and electric hearth appliances that are
purchased from an HHT authorized dealer.
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance will
be free from defects in materials and workmanship at the time of manufacture.
After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during
the applicable warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion,
may fully discharge all of its obligations under this manufacturer’s warranty by replacing the product itself or refunding the
veried purchase price of the product itself. The maximum amount recoverable under this warranty is limited to the purchase
price of the product. This warranty is subject to conditions, exclusions and limitations as described below.
Warranty coverage begins on the date of original purchase. In the case of new home construction, coverage under this
manufacturer’s warranty begins on the date of rst occupancy of the dwelling or six months after the sale of the product by
an independent, authorized HHT dealer/ distributor, whichever occurs earlier. The warranty period for this manufacturer’s
warranty shall commence no later than 24 months following the date of product shipment from HHT, regardless of the instal-
lation or occupancy date. The manufacturer’s warranty period for parts and labour for covered components is produced in
the following table.
The term “Limited Lifetime” in the table below is dened as: 20 years from the beginning date of warranty coverage for gas
appliances, and 10 years from the beginning date of warranty coverage for wood, pellet and coal appliances. These time
periods reect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period Heat & Glo Manufactured Appliances and Venting
Components Covered
Parts Labor Gas Wood Pellet EPA
Wood Coal Electric Venting
1 Year X X X X X X X
All Parts and Material Except
as covered by Conditions,
Exclusion, and Limitations listed
2 years
X X X Igniters, Electronic
Components, and Glass
X X X X X Factory-installed blowers
X Molded refractory panels
3 years X Firepots and burnpots
2000-645B (1-13) Page 1 of 3
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 6
Warranty Period Heat & Glo Manufactured Appliances and Venting
Components Covered
Parts Labor Gas Wood Pellet EPA
Wood Coal Electric Venting
5 years 1 years X X Castings & bafes
7 years 3 years X X X Manifold tubs HEAT & GLO
chimney and termination
10 years 1 year X Burners, logs and refractory
Limited
Lifetime 3 year X X X X X Firebox and heat exchanger
90 Days XXXXXXXAll Replacement Parts
beyond warranty period
OTHER RIGHTS
The HHT manufacturer’s warranty is in addition to other rights and remedies that you may have under Australian
law.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
WARRANTY CONDITIONS AND EXCLUSIONS:
• The HHT manufacturer’s warranty only covers HHT appliances that are purchased through an HHT authorized dealer
or distributor. A list of HHT authorized dealers is available on the HHT branded websites.
• This warranty is only valid while the HHT appliance remains at the site of original installation.
WARRANTY EXCLUSIONS:
This HHT manufacturer’s warranty does not cover the following:
• Changes in surface nishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface nishes may occur. This is not a aw and is not covered under warranty.
• Damage to printed, plated, or enamelled surfaces caused by ngerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts in-
clude: paint, wood, pellet and coal gaskets, rebricks, grates, ame guides, light bulbs, batteries and the discoloration
of glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identication label furnished with the appliance; (2) failure to in-
stall the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation,
abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly
performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by
tightly sealed constructions, insufcient make-up air supply, or handling devices such as exhaust fans or forced air fur-
naces or other such causes; (6) use of fuels other than those specied in the operating instructions; (7) installation or
use of components not supplied with the appliance or any other components not expressly authorized and approved
by HHT (8) modication of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interrup-
tions or uctuations of electrical power supply to the appliance.
2000-645B (1-13) Page 2 of 3
7Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
• Non Heat & Glo venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing replace system in which an insert or a decorative gas appliance is installed.
• Removal, installation, reinstallation, set up or any other costs associated with a claim including travel and shipping
charges for parts
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and conguration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
• The appliance has been over-red or operated in atmospheres contaminated by chlorine, uorine, or other damaging
chemicals. Over-ring can be identied by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel nishes.
• The appliance is subjected to prolonged periods of dampness or condensation.
There is any damage to the appliance or other components due to water or weather damage which is the result of, but not
limited to, improper chimney or venting installation.
HOW TO CLAIM
• To make a claim against this warranty, contact your local distributor during regular business hours. See addresses
below for a dealer nearest you. (Vic) Pty Ltd ACN 005 872 159 (Jetmaster).
• Additional service fees may apply if you are seeking warranty service from a dealer other than the dealer from whom
you originally purchased the product.
• Check with Jetmaster in advance for any costs to you when arranging a warranty call. Travel and shipping charges for
parts are not covered by this manufacturers’ warranty.
• HHT and Jetmaster will assess your claim. HHT or Jetmaster may need to inspect the product as part of the assess-
ment of your claim. If the product requires inspection, HHT or Jetmaster will discuss with you the best way for this to
occur.
• To make a claim under this manufacturer’s warranty, you must be able to prove when you purchased the product. The
easiest way to do this is through your original proof of purchase, for example your invoice or receipt. However, if you
do not have your original proof of purchase HHT or Jetmaster may accept other evidence of the date of purchase.
Melbourne
Jetmaster
444 Swan Street
Richmond 3121
(03) 9429-5573
Perth
Fireplace Corner
277 Lord Street
East Perth 6000
(08) 9228-2600
Sydney
Jetmaster
10 Martin Avenue
Arncliff 2205
(02) 9597-7222
2000-645B (1-13) Page 3 of 3
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 8
1
MODELS: COSMO-I30AU
LABORATORY:
TYPE:
STANDARD: AS4553-2008
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
Wheninstallingabove610meterelevation:
Reduce input rate 4% for each 305 meters feet above
610meters.
Materialwhichwillnotigniteandburn.Suchmaterialsare
thoseconsistingentirelyofsteel,iron,brick,tile,concrete,
slate,glassorplasters,oranycombinationthereof.
Materials that are reported as passing
shallbeconsidered
non-combustiblematerials.
Materialsmadeoforsurfacedwithwood,compressedpa-
per,plantbers,plastics,orothermaterialthatcanignite
and burn, whether ame proofed or not, or plastered or
unplasteredshallbeconsideredcombustiblematerials.
AllelectricalsafetytestinghasbeendonefollowingtheEN
60335-2-102standard.Localcodesapply.
TheHeat&GlogasappliancesdiscussedinthisInstaller’s
Guidehavebeentestedtocerticationstandardsandlisted
bytheapplicablelaboratories.
This appliance must be installed in accordance with the
rulesinforce.
NOXClass5forG20,NOXClass5forG31
WARNING! Risk of Explosion! An in-line regulator
MUST be installed if the gas pressure exceeds 3.4 kPa.
Failure to install a regulator could damage valve.
Pressure requirements for Cosmo-I30AU natural gas
andpropanegasreplacesareshownintablebelow.
Twotapsareprovidedonthefrontofthegascontrolfor
atestgaugeconnectiontomeasuretheinletandoutlet
pressures.
Thereplaceanditsindividualshut-offvalvemustbedis-
connectedfromthegassupplypipingsystemduringany
pressuretestingofthesystemattestpressuresinexcess
of60mbaror6kPa.
Ifthereplacemustbeisolatedfromthegassupplypip-
ingsystembyclosinganindividualshut-offvalve,itmust
beofthehandle-lesstype.
Natural Gas Propane
InletGasPressure 1.13to3.40kPa 2.75-3.40kPa
Outlet(Manifold)GasPressure .80kPa 2.46kPa
MaximumGasConsumption 26.0MJ/h 24.0MJ/h
BurnerInjector DMS42(2.37mm) DMS54(1.40mm)
PilotInjector .023 .014
Anin-lineregulatorMUSTbeinstalledifthegaspressureexceeds.Failuretoinstallaregulatorcoulddamage
valve.
9Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
2
WARNING! DO NOT operate replace before read-
ing and understanding operating instructions. Failure
to operate replace according to operating instructions
could cause re or injury.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.D.
MANTEL
SECTION 5.B
AND 11.A
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 12.H.
HEARTH
CLEAR SPACE
SECTION 2.C.
REQUIRED ISOLATION SWITCH: AS5601 LOCATION WITHIN 1 METRE OF
FIREPLACE, SUBJECT TO MANTEL PIECE, ETC. CHECK TO ENSURE IT
REMAINS CLEAR ON ANY MANTEL PIECE INSTALLATION.
APPLIANCE INSTALLED IN EXISTING SOLID
FUEL FIREPLACE OR CHASE CONSTRUCTED
FROM NON-COMBUSTIBLE MATERIALS.
Ifyouexpectthatsmallchildrenorvulnerableadultsmay
comeintocontactwiththisreplace,thefollowingprecau-
tionsarerecommended:
• Installaphysicalbarriersuchas:
User Guide
This appliance has been supplied with an integral barrier
to prevent direct contact with the xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrierisnotpresentorhelpisneededtoproperlyinstallone.
HOT SURFACES!
Glassandothersurfacesarehotduring
operationANDcooldown.
• DO NOTtouchglassuntilitiscooled
• NEVERallowchildrentotouchglass
• Keepchildrenaway
• CAREFULLY SUPERVISE children in same room as
replace.
• Alertchildrenandadultstohazardsofhightemperatures.
• Keepclothing,furniture,draperiesandotherammable
materialsaway.
- Adecorativerescreen.
- Adjustablesafetygate.
• Installaswitchlockorawall/remotecontrolwithchild
protectionlockoutfeature.
• Keepremotecontrolsoutofreachofchildren.
• Neverleavechildrenalonenearahotreplace,whether
operatingorcoolingdown.
• TeachchildrentoNEVERtouchthereplace.
• Considernotusingthereplacewhenchildrenwillbe
present.
Contactyourdealerformoreinformation, or visit: www.
hpba.org/safety-information.
Topreventunintendedoperationwhennotusingyourre-
place for an extended period of time (summer months,
vacation/trips,etc):
• Removebatteriesfromremotecontrols.
• Turnoffwallcontrols.
WARNING! Choking Hazard! Keep media out of reach
of children.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 10
WARNING! DO NOT place combustible objects in front
of the replace or block louvers. High temperatures may
start a re. See Figure 2.2.
Avoidplacingcandlesandotherheat-sensitiveobjectson
mantelorhearth.Heatmaydamagetheseobjects.
SeeSection12.G.
WARNING! Risk of Fire! Install ONLY doors, fronts or
surrounds approved by Hearth & Home Technologies.
Unapproved doors or fronts may cause appliance to over-
heat.
This appliance has been supplied with an integral
barrier to prevent direct contact with the xed glass
panel. DO NOT operate the appliance with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
installone.
Formoreinformationrefertotheinstructionssuppliedwith
yourdecorativedoororfront.
Followtheinstructionssuppliedwiththecontrolinstalled
tooperateyourreplace:
Forsafety:
• Installaswitchlockorawall/remotecontrolwithchild
protectionlockoutfeature.
• Keepremotecontrolsoutofreachofchildren.
Seeyourdealerifyouhavequestions.
CLEAR SPACE
3 FT. IN FRONT OF FIREPLACE
APPLIANCE INSTALLED IN EXISTING
SOLID FUEL FIREPLACE
1. ThecontrolmodulehasanON/OFF/REMOTEselector
switchthatmustbeset.SeeFigure2.3.
OFFPosition:Appliancewillignoreallpowerinputsand
willnotrespondtoanycommandsfromawallswitchor
remote.TheunitshouldbeintheOFFpositionduring
installation,service,batteryinstallation,fuelconversion,
andintheeventthatthecontrolgoesintoLOCK-OUT
modeasaresultofanerrorcode.
ONPosition:Appliancewilligniteandruncontinuously
in the HI ame setting, with no adjustment in ame
output.This modeof operationis primarilyused for
initialinstallationorpoweroutageoperationwithbattery
backup.
REMOTEPosition:Appliancewillinitiatecommands
fromanoptionalwiredwallswitchand/orthewireless
remote(RC300),suppliedstandard.
2.IfusingawiredwallswitchwiththemoduleinREMOTE
mode,theameoutputcanbeadjustedwiththeHI/LO
selectorswitchonthemodule.SeeFigure2.3.Note
thattheameHI/LOselectorswitchwillbecomeinactive
once an optional remote control (RC200/RC300) is
programmedtothecontrolmodule.Notethatthecontrol
modulewillalwaysignitethereplaceonHIandremain
sofortheinitial10secondsofoperation.IftheHI/LO
is switched to the LO position, the ame output will
automaticallydroptothelowestsettingaftertheame
hasbeenestablishedfor10sec.Afterthis10second
period,theamecanbeadjustedfromHItoLOwith
theswitch.
3. Thecontrolmodulehassafetyfeaturethatautomatically
shutsdownthereplace after 9 hoursof continuous
operationwithoutreceivingacommandfromtheRC300
remote.
TheIntelliFirePlusTMsystemhasabatterybackupoption.
Batterylongevityandperformancewillbeaffectedbythe
servicetemperaturesofthisappliance.
NOTICE: Batteries should only be used as a power source
in the event of an emergency such as an outage.
11Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
Note: Ifthemodule is in LOCK-OUT mode,resetting the
circuitbreakertotheappliancewillalsoresetthemodule.
Note: ForunitsinstalledinAustralia,theresidence’s220/240
vac wall outlet to which this appliance’s power cord is
connected,mustbewiredtoanin-lineon/offswitch.Thisis
requiredforservicingand/orresettingthecontrolmodulein
theeventofacontrolmoduleLOCK-OUT.
Beforeoperating this replacefor the rsttime,
:
• Verifyallshippingmaterials have been removedfrom
insideand/orunderneaththerebox.
• Reviewproperplacementoflogs,embermaterialand/
orotherdecorativematerials.
• Checkthewiring.
• Checktheairshutteradjustment.
• Ensurethattherearenogasleaks.
• Ensurethattheglassissealedandintheproperposition
andthattheintegralbarrierisinplace.
WARNING! Risk of Fire/Asphyxiation! DO NOT oper-
ate replace with xed glass assembly removed.
Determineif thisreplacehasastandingpilot oranIn-
telliFirePlusTMignitionsystem.Askyour dealeror open
controlaccesspanel,lookatgasvalve.
• Astandingpilotignitionwillhavearedorblackignitor
button(refertoFigure2.4).
• AnIntelliFirePlusTMignitionsystemwillnothaveabutton.
RED OR BLACK IGNITOR BUTTON
LP/NG GAS-TYPE
SELECTOR SWITCH
WIRE LEAD FROM
REGULATOR CONNECTS HERE
MODULE
SELECTOR
SWITCH
5. Module Reset
This module may lock-out under certain conditions.
When this occurs, the appliance will not ignite or
respondtocommands.Themodulewillgointolock-out
modebyemittingthreeaudiblebeeps,thencontinuously
displayinganerrorcodeatitsstatusindicatorLED.
• Check battery tray. Remove batteries if installed.
Batteriesshouldonlybeinstalledforuseduringpower
outages.SeeSectionG.
• Locatethemoduleselectorswitch.(SeeFigure2.3).
• SetthemoduleselectorswitchtotheOFFposition.
• Waitve(5)minutestoallowpossibleaccumulatedgas
toclear.
• Set the module selector switch to ON or REMOTE
position.
• Starttheappliance.
WARNING! Risk of Explosion! DO NOT press the mod-
ule reset switch more than one time within a ve minute
time period. Gas may accumulate in rebox. Call a quali-
ed service technician.
4. Ifyouintendtousebothanoptionalwiredwallswitch,
andtheRC300remotecontroltooperateyourreplace,
thewallswitchwilloverrideanycommandsgivenby
theremote.
Thisappliancehasasafetyfeaturethatautomatically
shutsdownthereplaceafter9hoursofcontinuous
operationwithoutreceivingacommandfromthewall
switchoroptionalremote.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 12
TheIPIsystemmaybeoperated with fourAA-cellbatteries.Whenusingbatteries, unplug the transformer.Toprolong
batterylife,removethemwhenusingthetransformer.
This appliance is equipped with an ignition
devicewhichautomaticallylightstheburner.
DO NOTtrytolighttheburnerbyhand.
Wait ve (5) minutes to clear out any gas.
Thensmellforgas,includingneartheoor.If
yousmellgas,STOP!Follow“B”intheSafety
Informationlocatedontheleftsideofthisla-
bel.Ifyoudonotsmellgas,gotonextstep.
Tolighttheburner:
Equippedwithwallswitch:TurnON/OFFswitch
toON.
Equippedwithremoteorwallcontrol:Press
ONorFLAMEbutton.
Equippedwiththermostat:Settemperatureto
desiredsetting.
Iftheappliancedoesnotlightafterthreetries,
callyourservicetechnicianorgassupplier.
LIGHTING
TO TURN OFF
GAS TO APPLIANCE
Equippedwithwallswitch:TurnON/OFFswitch
toOFF.
Equippedwithremoteorwallcontrol:Press
OFFbutton.
Equippedwiththermostat:Settemperatureto
lowestsetting.
Service technician should turn off electric
powertothecontrolwhenperformingservice.
READ BEFORE LIGHTING
Ifyoudonotfollowtheseinstructionsexactly,areorexplosion
mayresultcausingpropertydamage,personalinjuryorlossoflife.
CAUTION:
NOT FOR USE
593-913G
GAS
VALVE
Foradditionalinformationonoperatingyour
Hearth&HomeTechnologiesreplace,pleaserefertowww.replaces.com.
Thisapplianceisequippedwithan
intermittentpilotignition(IPI)device
whichautomaticallylightstheburn-
er.DO NOTtrytolighttheburnerby
hand.
smellallaround
theapplianceareaforgas.Besureto
smellnexttotheoorbecausesome
gasisheavierthan airand willsettle
ontheoor.
•DO NOTtrytolightanyappliance.
• DO NOTtouchanyelectricswitch;do
notuseanyphoneinyourbuilding.
DO NOT CONNECT LINE VOLT-
Improper installation, adjustment, al-
teration, service or maintenance can
causeinjuryorpropertydamage.Re-
fertotheowner’sinformationmanual
providedwiththisappliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustionandventilationair.
If not installed, operated, and main-
tainedinaccordancewiththemanufac-
turer’s instructions, this product could
expose you to substances in fuel or
fuelcombustionwhichareknowntothe
StateofCaliforniatocausecancer,birth
defects,orotherreproductiveharm.
Keepburnerandcontrolcompartment
clean. See installation and operating
instructionsaccompanyingappliance.
Hotwhileinoperation.DO NOTtouch.
Keepchildren,clothing,furniture,gaso-
lineandotherliquidshavingammable
vaporsaway.
DO NOT operate the appliance with
xedglassassemblyremoved,cracked
or broken. Replacement of the xed
glassassembly should bedoneby a
licensedorqualiedserviceperson.
•Immediately call your gas supplier
fromaneighbor’sphone.Followthe
gassupplier’sinstructions.
•If you cannot reach your gas sup-
plier,calltheredepartment.
use this appliance if any
parthasbeenunder water.Imme-
diatelycallaqualiedservicetech-
niciantoinspecttheapplianceand
to replace any part of the control
systemandanygas controlwhich
hasbeenunderwater.
Forusewithnaturalgasandpropane.
A conversion kit, as supplied by the
manufacturer,shallbeusedtoconvert
thisappliancetothealternatefuel.
For assistance or additional informa-
tion, consult a qualied installer, ser-
viceagencyorthegassupplier.
13Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
InitialBreak-inProcedure
• The appliance should be run three to four hours
continuouslyonhigh.
• Turntheapplianceoffandallowittocompletelycool.
• Removexedglassassembly.SeeSection12G.
• Cleanxedglassassembly.SeeSection3.
• Replacethexedglassassemblyandruncontinuously
onhighanadditional12hours.
This cures the materials used to manufacture the re-
place.
NOTICE! Open windows for air circulation during ap-
pliance break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
ISSUE SOLUTIONS
Condensationontheglass Thisisaresultofgascombustionandtemperaturevariations.Astheappliancewarms,this
condensationwilldisappear.
Blueames Thisisaresultofnormaloperationandtheameswillbegintoyellowastheapplianceisal-
lowedtoburnfor20to40minutes.
Odorfromappliance
Whenrstoperated,thisappliancemayreleaseanodorfortherstseveralhours.Thisiscaused
bythecuringofthepaintandtheburningoffofanyoilsremainingfrommanufacturing.Odormay
alsobereleasedfromnishingmaterialsandadhesivesusedaroundtheappliance.
Filmontheglass
Thisisanormalresultofthecuringprocessofthepaintandlogs.Glassshouldbecleaned
within3 to 4 hours ofinitialburningto remove deposits left byoilsfrom the manufacturing
process.Anon-abrasivecleanersuchasgasreplaceglasscleanermaybenecessary.See
yourdealer.
Metallicnoise
Noiseiscausedbymetalexpandingandcontractingasitheatsupandcoolsdown,similarto
thesoundproducedbyafurnaceorheatingduct.Thisnoisedoesnotaffecttheoperationor
longevityoftheappliance.
DelayfromONcommandtoburner
ignition
Itisnormaltohavea5-20seconddelaybetweentheexecutionoftheONcommandandthe
ignitionoftheburnerame.Thedelayispartofthepilotrecticationprocessanddoesnot
affectperformance.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 14
Seasonally
Homeowner
Tools Needed: Protective gloves, glass cleaner, drop
clothandastableworksurface.
CAUTION! Handle xed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
•Prepareaworkarealargeenoughtoaccommodatexed
glassassemblyanddoorframebyplacingadropcloth
onaat,stablesurface.
Note:Fixedglassassemblyandgasketingmayhaveres-
iduethatcanstaincarpetingoroorsurfaces.
•Removedoorordecorativefrontfromapplianceandset
asideonworksurface.
• SeeSection12.Gforinstructionstoremovexedglass
assembly.
• Cleanglasswithanon-abrasivecommerciallyavailable
cleaner.
- Lightdeposits:Useasoftclothwithsoapandwater
- Heavy deposits: Use commercial fireplace glass
cleaner(consultwithyourdealer)
• Carefullysetxedglassassemblyinplaceonappliance.
Hold glass in place with one hand and secure glass
latcheswiththeotherhand.
• Reinstalldoorordecorativefront.
3
The following tasks may be performed annually by the
homeowner.Ifyouareuncomfortableperforminganyof
thelistedtasks,pleasecallyourdealerforaserviceap-
pointment.
Morefrequentcleaningmayberequiredduetolintfrom
carpetingor otherfactors.Control compartment,burner
andcirculatingairpassagewayoftheappliancemustbe
keptclean.
CAUTION! Risk of Burns! The appliance should be
turned off and cooled before servicing.
Whenproperlymaintained, your appliance willgive you
manyyearsoftrouble-freeservice.Werecommendan-
nualservicebyaqualiedtechnician.
Annually
Homeowner
Tools needed:Protectivegloves,stableworksurface
• Assessconditionofscreenandreplaceasnecessary.
• Inspectforscratches,dentsorotherdamageandrepair
asnecessary.
•Checkthatlouversarenotblocked.
• Vacuumordustsurfaces.
Seasonally
Homeowner
Tools needed: Replacementbatteriesandremotecon-
trolinstructions.
• Locateremotecontroltransmitterandreceiver.
• Verify operation of remote. Refer to remote control
operationinstructionsforpropercalibrationand setup
procedure.
• Placebatteries as neededinremote transmittersand
battery-poweredreceivers.
• Placeremotecontroloutofreachofchildren.
Ifnotusingyourreplaceforanextendedperiodoftime
(summer months, vacations/trips, etc), to prevent unin-
tendedoperation:
• Removebatteriesfromremotecontrols.
Seasonally
Homeowner
Tools needed: Protectiveglovesandsafetyglasses.
• Inspect venting and termination cap for blockage or
obstructionsuchplants,birdnests,leaves,snow,debris,
etc.
• Verifyterminationcapclearancetosubsequentconstruc-
tion(buildingadditions,decks,fences,orsheds).See
Section6.
• Inspectforcorrosionorseparation.
• Verifyweatherstripping,sealingand ashing remains
intact.
• Inspectdraftshieldtoverifyitisnotdamagedormissing.
Anysafetyscreenorguardremovedforservicingmustbe
replacedpriortooperatingtheappliance.
Installationandrepairshouldbedonebyaqualiedtechni-
cian only. The appliance should be inspected before use
andatleastannuallybyaprofessionalserviceperson.
15Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
The following tasks must be performed by a qualied
technician.
Annually
ServiceTechnician
Tools needed:Protectivegloves,dropclothandastable
worksurface.
• Inspectgasketsealanditscondition.
• Inspectxedglassassemblyforscratchesandnicksthat
canleadtobreakagewhenexposedtoheat.
• Conrm there is no damage to glass or glass frame.
Replaceasnecessary.
• Verifythatxedglassassemblyisproperlyretainedand
attachment components are intact and not damaged.
Replaceasnecessary.
Media
Annually
ServiceTechnician
Tools needed:Protectivegloves.
• Inspect for damaged or missing media. Replace as
necessary.RefertoSection12.Fformediainformation.
• Verifycorrectlogplacementandnoameimpingement
causingsooting.Correctasnecessary.
Annually
ServiceTechnician
Tools needed:Protectivegloves,sandpaper,steelwool,
cloths,mineralspirits,primerandtouch-uppaint.
• Inspectforpaintcondition,warpedsurfaces,corrosion
orperforation.Sandandrepaintasnecessary.
• Replaceapplianceifreboxhasbeenperforated.
Annually
ServiceTechnician
Tools needed:Protectivegloves,vacuumcleaner,dust
cloths
• Vacuumandwipeoutdust,cobwebs,debrisorpethair.
Usecautionwhencleaningtheseareas.Screwtipsthat
havepenetratedthesheetmetalaresharpandshould
beavoided.
• Removeallforeignobjects.
• Verifyunobstructedaircirculation.
Annually
ServiceTechnician
Tools needed:Protectivegloves,vacuumcleaner,whisk
broom, ashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verifyburnerisproperlysecuredandalignedwithpilot
origniter.
• Cleanoffburnertop,inspectforpluggedports,corrosion
ordeterioration.Replaceburnerifnecessary.
• Verifybatterieshavebeenremovedfrombatteryback-
upIPIsystemstopreventprematurebatteryfailureor
leaking.Foroptimalbatterylife,locatethebatterypack
outsideofthecontrolcavityonthehearth.Thisplace-
mentwillreducethechancesofoverheatingthebatteries
during extended burns which could result in reduced
batterylifeordegradation.
• Checkforsmoothlightingandignitioncarryovertoall
ports.Verifythatthereisnoignitiondelay.
• Inspectforliftingorotherameproblems.
• Verifyairshuttersettingiscorrect.SeeSection12.Hfor
requiredairshuttersetting.Verifyairshutterisclearof
dustanddebris.
• Inspectoriceforsoot,dirtandcorrosion.Verifyorice
sizeiscorrect.SeeServicePartsListforproperorice
sizing.
• Verifymanifoldandinletpressures.Adjustregulatoras
required.
• Inspectpilotamepatternandstrength.SeeFigure3.1
forproperpilotame pattern. Clean orreplace orice
spudasnecessary.
• Inspect IPI ame sensing rod for soot, corrosion and
deterioration.Polishwithnesteelwoolorreplaceas
required.
• Verifythatthereisnotashortinamesensecircuitby
checkingcontinuitybetweenpilothoodandamesense
rod.Replacepilotasnecessary.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 16
NOTICE: Illustrations and photos reect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
VERTICAL TERMINATION CAP (SECTION 8)
VENT PIPE
(SECTION 8)
GAS LINE (SECTION 9)
ACCESS THROUGH EXISTING
MASONRY OR WOODBURNING
FIREPLACE
HEARTH EXTENSION
SURROUND OR FRONT
NOT SHOWN
SECTION 2.D AND 12.I.
MANTEL AND MANTEL LEG
SECTION 5.B AND 11.A
3 in. (76 mm)
FLEX LINERS
(SECTION 8)
OPTIONAL WALL SWITCH
STORM COLLAR
(SECTION 6 AND 8)
VENT PIPE PENETRATES
ROOF PREFERABLY
WITHOUT AFFECTING
ROOF RAFTERS
(SECTION 8)
CEILING FIRESTOP ON
FLOOR OF ATTIC
(SECTION 8)
FRAMING/HEADER
(SECTION 5)
NON-COMBUSTIBLE ROOF
FLASHING MAINTAINS
MINIMUM CLEARANCE
AROUND PIPE (SECTION 10)
REQUIRED ISOLATION SWITCH: AS5601
LOCATION WITHIN 1 METER OF FIREPLACE,
SUBJECT TO MANTEL PIECE, ETC. CHECK
TO ENSURE IT REMAINS CLEAR ON ANY
MANTEL PIECE INSTALLATION
DOUBLE LINED FLUE TO COMPLY WITH
AS2918:2001 AND THE BUILDING CODE OF
AUSTRALIA
4
Installer Guide
17Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
Heat&Glogasinsertsaredesignedforinstallationsinto
solid fuel masonry or factory built replaces that have
been installed in accordance with the National, Provin-
cial,Stateandlocalbuildingcodes.Fireplacesaretobe
constructedofnon-combustiblematerialsand,intheab-
senceoflocalorregionalcodes,meetcriteriaofNFPA
211.Noadditionaloutsideairsourceisrequired.
InstallationMUSTcomplywithlocal,regional,stateandna-
tionalcodesandregulations.Consultinsurancecarrier,local
buildinginspector,reofcialsorauthoritieshavingjurisdic-
tionoverrestrictions,installationinspectionandpermits.
Priortoinstallingthegasinsert:
• Have the chimney and adjacent structure inspected
andcleanedbyqualiedprofessionals.Hearth&Home
Technologies recommends that NFI or CSIA certied
professionals,ortechniciansunderthedirectionofcerti-
edprofessionals,conductaminimumofaNFPA211
Level2inspectionofthechimney.
• Replacecomponentpartsofthechimneyandreplace
asspeciedbytheprofessionals.
• Ensure combustible mantel and surround clearances
complywithapplicablecodesandregulationsforsolid-
fuelreplaces.Intheabsenceoflocalorregionalcodes,
refertoNFPA211.
• Ensurealljointsareproperlyengagedandthechimney
isproperlysecured.
• Minimumreplacesize.SeeSection5.A.
• Gassupplypipingrequirements.
• Electricalwiringrequirements.
• Finishingdetails.
• Whetheroptionalaccessories—devicessuchasawall
switchorremotecontrol—aredesired.
• Carefullyremovetheapplianceandcomponentsfrom
thepackaging.
• Theventsystemcomponentsanddecorativedoorsand
frontsmaybeshippedinseparatepackages.
• Ifpackagedseparately,thelogsetandappliancegrate
mustbeinstalled.
• Reporttoyourdealeranypartsdamagedinshipment,
particularlytheconditionoftheglass.
• -
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, in-
complete or substitute components. Keep appliance dry.
Hearth&HomeTechnologiesdisclaimsanyresponsibilityfor,
andthewarrantywillbevoidedby,thefollowingactions:
• Installation and use of any damaged appliance or vent
systemcomponent.
• Modicationoftheapplianceorventsystem.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improperpositioningofthegaslogsortheglassdoor.
• Installationand/oruseofanycomponentpartnotapproved
byHearth&HomeTechnologies.
WARNING! Risk of Fire/Explosion/Electric Shock! DO
NOT use this appliance if any part has been under water.
Call a qualied technician to inspect the appliance and to
replace any part of the control system and/or gas control
which has been under water.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualied
technician,serviceagencyoryourdealer.
Beforebeginningtheinstallationbesurethatthefollowing
toolsandbuildingsuppliesareavailable.
Tapemeasure Framingmaterial
Pliers Non-corrosiveleakchecksolution
Hammer Phillipsscrewdriver
Gloves Framingsquare
Voltmeter Electricdrillandbits-1/4in.(6mm)
Plumbline Safetyglasses
Level Reciprocatingsaw
Manometer Flatbladescrewdriver
1/2-3/4in.(13-18mm)length,#6or#8
Self-drillingscrews
Caulkingmaterial149°C(300°F)minimumcontinuous
exposurerating)
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 18
5
Minimumreplaceopeningrequirementsforastandard3/4
inchdeepsurroundareshowninFigure5.2.Forsmaller
openings,anoptional1-1/2in.(38mm)deepsurroundis
availableanddimensionsareshowninFigure5.3.
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be locat-
ed out of trafc and away from furniture and draperies.
• Therebrick(refractory),glassdoors,screenrails,screen
mesh and log grates can be removed from a factory
builtreboxinordertogainminimumgasinsertopening
requirements.
• Anysmokeshelves,shieldsandbafesmayberemoved
fromthefactorybuiltreboxifattachedwithmechanical
fasteners.
• Themetaloorofthesolidfuelreboxmayberemoved
tofacilitatetheinstallationoftheinsert.
• Cuttingofanysheetmetalpartsofthereplaceinwhich
thegasreplaceinsertistobeinstalledisprohibited,
excepttheoorastestedforandasnotedaboveandin
Figure5.1.
• Aminimum1/2in.(13mm)gapfromthebottomofthe
applianceto themetaloorofthe solidfuelreboxis
RECOMMENDED for optimal fan performance. See
sideviewinFigure5.1
SIDE VIEW
METAL INSERT
FACTORY BUILT FIREBOX
3 in. (76 mm)
9 in.
(229 mm)
METAL FLOOR OF EXISTING
SOLID FUEL FIREBOX
TOP VIEW
REMOVE THIS
SECTION OF
METAL FLOOR
REMOVE THIS
SECTION OF
METAL FLOOR
METAL FLOOR OF EXISTING SOLID FUEL FIREBOX
1/2 in. (13 mm) MINIMUM LEVELING
HEIGHT (RECOMMENDED)
1/4 in. (6 mm) REQUIRED
5 in.
(127 mm)
5 in.
(127 mm)
6 in.
(152 mm)
6 in.
(152 mm)
9 in.
(229 mm)
3 in. (76 mm)
• Theappliancemaynotbeplaceddirectlyonthebase
of the outer wrap, a 1/4 in. (6 mm) airspace MUST
be provided between the insert and the oor of the
outerwrap.Usethelevelinglegstoraisetheinserta
minimumof1/4inch.Theoriginalreplacemaynever
bereturnedtosolidfuelinthiscondition.Thesidewalls
andtopstructureofthereboxmaynotbealteredwith
theexceptionofremovablebafesanddampers.
• Ifaminimum1/2in.(13mm)gapcannotbeachieved,
asectionofthefactory-builtmetaloorcanberemoved.
SeeFigure5.1-B.
19Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14
Inadditiontothesedimensions,alsoreferenceClearances
andMantelProjections(Section5.B).
B
A
G
ED
C
F
TOP VIEW SIDE VIEWFRONT VIEW
Location
ARearWidth 20-1/4 514
B FrontWidth 30-1/2 775
CGlassOpeningWidth 27-7/16 697
DGlassOpeningHeight 12-13/16 325
E Height-Front 20-1/2 521
F Height-Rear 17-5/8 448
GUnitDepth 14-5/8 371
*Note:Ifexhaustcollaroninsertandreplacedamperdonotlineup,add4in.(102mm)tominimum
replaceheightforbendsinventpipe.
Heat & Glo • Cosmo-I30AU • 2243-900 Rev. W • 10/14 20
WARNING! Risk of Fire! Comply with all minimum clear-
ances to combustibles as specied. Framing or nishing
material closer than the minimums listed must be construct-
ed entirely of noncombustible materials (i.e., steel studs,
concrete board, etc).
Clearance to combustible material under the insert is 1/4
in. (6 mm). Clearance from top of replace opening for
combustibles extending 12 in. (305 mm) max. is 12 in.
(305 mm).
• Use leveling legs to raise insert minimum 1/4 in. (6 mm)
above combustible material or outer wrap of factory built
rebox.
Combustible facings must not extend behind the insert
surround. For non-combustible material specications
refer to Section 1.E.
Appliances
12 in.
(305 mm)
MAX.
NON-COMBUSTIBLE FACING
MINIMUM CLEARANCE
TO COMBUSTIBLE
MANTEL OR
PROJECTION
12 in.
(305 mm)
MIN.
CD
SURROUND
APPLIANCE
1-1/2 in.
(38 mm)
BD
AD
APPLIANCESURROUND
SIDE VIEW TOP VIEW
Location SUPREME-I30AU
ADAlternateUnitWidth 29-1/16 738
BDAlternateUnitDepth 13-7/8 352
CDAlternateUnitHeight 19-1/16 484
*Note:Ifexhaustcollaroninsertandreplacedamperdonotlineup,add4in.(102mm)tominimumreplace
heightforbendsinventpipe.
Other manuals for COSMO-I30AU
2
Table of contents
Other Heat & Glo Indoor Fireplace manuals
Heat & Glo
Heat & Glo 6000TRSI-AUC User manual
Heat & Glo
Heat & Glo 6100PLUS User manual
Heat & Glo
Heat & Glo Wood Burning Fireplace RH-36 Series User manual
Heat & Glo
Heat & Glo Crescent II User manual
Heat & Glo
Heat & Glo TIARAP-BK-IPI User manual
Heat & Glo
Heat & Glo 8000TR-OAK User manual
Heat & Glo
Heat & Glo FDN-5-PIER User manual
Heat & Glo
Heat & Glo 6000CLX-IPI-T User manual
Heat & Glo
Heat & Glo ST-550T-IPI User manual
Heat & Glo
Heat & Glo PRIMO48-CF User manual
Heat & Glo
Heat & Glo NORTHSTAR-BK User manual
Heat & Glo
Heat & Glo COSMO-I30AU User manual
Heat & Glo
Heat & Glo i30-X User manual
Heat & Glo
Heat & Glo SL-550TR-E User manual
Heat & Glo
Heat & Glo TRUE-36G-IFT User manual
Heat & Glo
Heat & Glo SOHO24B User manual
Heat & Glo
Heat & Glo MEZZO48-B User manual
Heat & Glo
Heat & Glo SL-750TRSFHHIPI User manual
Heat & Glo
Heat & Glo Wood Burning Fireplace RH-36 Series User manual
Heat & Glo
Heat & Glo PRIMO-II-48 User manual
Popular Indoor Fireplace manuals by other brands
Brilliant Fires Limited
Brilliant Fires Limited 301C User, installation and servicing instructions
EmberGlow
EmberGlow VFF26NLM Owner's operation and installation manualmanual
Miles Industries
Miles Industries 530XAN Installation and owner's manual
Napoleon
Napoleon Electric Fireplace EF30 Installation and operating instructions
FMI
FMI VGM Series OWNER'S OPERATION AND INSTALLATION MANUAL
Monessen Hearth
Monessen Hearth Designer Vent Free Firebox LLF36 Product specifications
UC Living
UC Living Rosmore Slide Control User instructions, installation, maintenance
Ambiance Fireplaces
Ambiance Fireplaces INTIRGUE UF0110 manual
Dimplex
Dimplex Optiflame 3D Braemar BMR20 Operating instructions manual
Jøtul
Jøtul F 602 N Installation instructions with technical data
Bellfires
Bellfires UNICA-2 55 Instructions for use & manual daily maintenance
Ventis
Ventis VB00014 owner's manual