Heat & Glo Models:6000GLX-IPI-S User manual

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 1
Models:
6000GLX-IPI-S
6000GLX-IPI-R
6000GLX-IPILP-S
6000GLX-IPILP-R
Owner’s Manual
Installation and Operation
Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com. Pour demander un exemplaire en français de ce
Manuel du propriétaire, visitez www.heatnglo.com.
• Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.
• What to do if you smell gas
- Do not try to light any appliance
- Do not touch any electrical switch. Do not
use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas suppli-
er’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
bya qualifiedinstaller,serviceagency,orthe
gas supplier.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
DO NOT DISCARD THIS MANUAL
CAUTION
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installedinaccordancewiththemanufacturer’sinstructionsand
themanufactured home construction and safety standard,Title
24CFR,Part3280orStandardforInstallationinMobileHomes,
CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
• Leave this manual with
party responsible for use
and operation.
DO NOT
DISCARD
• Important operating
and maintenance
instructions included.
• Read,understandandfollow
these instructions for safe
installation and operation.
In the Commonwealth of Massachusetts:
• installation must be performed by a licensed plumber
or gas fitter;
See Table of Contents for location of additional
Commonwealth of Massachusetts requirements.
WARNING
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT SURFACES!
Glassandothersurfacesarehotduring
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
Î

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
2
Congratulations
Listing Label Information/Location
Model Name:___________________________________________ Date purchased/installed:__________________
Serial Number:__________________________________________ Location on appliance: ____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Congratulations on selecting a Heat & Glo gas appliance
—an elegant and clean alternative to wood burning
appliances. The Heat & Glo gas appliance you have
selected is designed to provide the utmost in safety,
reliability, and efficiency.
As the owner of a new appliance, you’ll want to read and
carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all Cautions
and Warnings.
This Owner’s Manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.
Your new Heat & Glo gas appliance will give you years of
durable use and trouble-free enjoyment. Welcome to the
Heat & Glo family of appliance products!
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
We recommend that you record the following
pertinent information about your appliance.
Gas and Electric
Information
Model Number
Serial Number
Type of Gas
The model information regarding your specific appliance can be found on
the rating plate usually located in the control area of the appliance.
Homeowner Reference Information
Heat & Glo, a of Hearth & Home Technologies, Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
brand
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
This appliance must beinstalled in accordance with local codes, if any; if not, follow ANSI Z223.1
intheUSAorCAN/CGA B149installation codes.(Installerl’appareilselonlescodesoureglements
locaux ou,en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
Type of Gas (Sorte De Gaz):
NATURAL GAS
MADE IN USA
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
ApprovedMinimum(DeGaz)Acceptable0.0in w.c. (Po.Col.d’eau)
MaximumPressure (Pression) 0.0in w.c. (Po.Col.d’eau)
MaximumManifoldPressure(Pression) 0.0in w.c. (Po.Col.d’eau)
MinimumManifoldPressure(Pression) 0.0in w.c. (Po.Col.d’eau)
Model:
(Modele):
Serial
(Serie):
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
XXXXXXXX
INCANADA
ALTITUDE:0-0000 FT.0000-0000FT.
MAX.INPUTBTUH: 00,000 00,000
MIN.INPUT BTUH: 00,000 00,000
ORIFICESIZE: #XXXXX #XXXXX XXXXXXXX
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
This product may be covered by one or more of the following patents: (Nos produits sont couverts par un ou plusieurs des brevets suivants): (United States)
4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495,
5452708,5542407, 5601073, 5613487,5647340,5688568, 5762062, 5775408, 5890485,5931661,5941237, 5947112,5996575,6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2,
6729551, 6736133, 6748940, 6748942, D320652, D445174, D462436; (Canada)1297749, 2195264, 2225408; or other U.S. and foreign patents pending (ou
autresbrevetsamericains etetrangers en attente).

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 3
Section 1: Listing and Code Approvals
A. Appliance Certification................................... 4
B. BTU Specifications........................................ 4
C. High Altitude Installations .............................. 4
D. Non-Combustible Materials Specifications.... 4
E. Combustible Materials Specifications............ 4
F. Requirements for the Commonwealth
of Massachusetts........................................... 5
Section 2: Getting Started
A. Design and Installation Considerations......... 6
B. Tools and Supplies Needed........................... 6
C. Inspect Appliance and Components.............. 6
Section 3: Framing and Clearances
A. Selecting Appliance Location......................... 7
B. Constructing the Appliance Chase ................ 8
C. Clearances .................................................... 8
D. Mantel Projections......................................... 9
Section 4: Termination Locations
A.Vent Termination Minimum Clearances....... 10
Section 5: Vent Information and Diagrams
A. Vent Table Key............................................. 12
B. Use of Elbows..............................................12
C. Measuring Standards .................................. 12
D. Vent Diagrams............................................. 13
Section 6: Vent Clearances and Framing
A. Pipe Clearances to Combustibles............... 22
B. Wall Penetration Framing............................ 22
C. Vertical Penetration Framing....................... 23
Section 7: Appliance Preparation
A. Choosing the Top or Rear Vent ...................24
B. Installing the Non-Combustible Board......... 25
C. Securing and Leveling the Appliance ..........25
D. Install the Optional Heat-Zone-Gas Kit........ 26
Section 8: Installing Vent Pipe
A. DVP PipeAssembly of Vent Sections.......... 27
B. Disassembly of Vent Sections..................... 29
C. Installing Heat Shield & Termination Cap ... 30
D. SL-D Pipe Assembly of Vent Sections......... 31
E. Installing Wall Shield Firestops and
Horizontal Termination Caps ....................... 32
F. Installing Roof Flashing and Vertical
Termination Cap .......................................... 33
- Table of Contents -
Î= Contains updated information.
Section 9: Gas Information
A. Fuel Conversions...................................... 35
B. Gas Pressures.......................................... 35
C. Gas Connection........................................ 35
Section 10: Electrical Information
A. Recommendation for Wire........................ 36
B. Connecting to the Appliance..................... 37
C. Intellifire Ignition System Wiring................37
D. Junction Box Installation........................... 37
Section 11: Finishing
A. Mantel Projections .................................... 39
B.Facing Material......................................... 39
C. Finishing Material...................................... 40
Section 12: Appliance Setup
A. Remove Shipping Materials...................... 41
B. Remove/Install Lights ............................... 41
C. Clean the Appliance.................................. 41
D. Accessories .............................................. 41
E. Installing the Refractory............................ 41
F. Ember Placement..................................... 42
G. Positioning the Logs ................................. 43
H. Glass Assembly ........................................ 46
I. Screen Mesh............................................. 46
J. Grilles and Trim......................................... 46
K. Air Shutter Setting..................................... 46
Section 13: Operating Instructions
A. Before Lighting Appliance......................... 47
B. Lighting Appliance..................................... 48
C. After Appliance is Lit ................................. 49
D. Frequently Asked Questions..................... 49
Section 14: Troubleshooting
A. Intellifire Ignition System........................... 50
Section 15: Maintaining and Servicing Appliance........... 52
A. Replacing the Light Bulbs......................... 52
Section 16: Reference Materials
A. Appliance Dimension Diagram .................54
B. Vent Components Diagrams..................... 55
C. Service Parts ............................................61
D. Warranty ................................................... 65
E. Contact Information .................................. 66

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
4
NOTE: Thisinstallationmustconformwithlocalcodes.Inthe
absence of local codes you must comply with the National
Fuel Gas Code, ANSI Z223.1-latest edition in the U.S.A.
and the CAN/CGA B149 Installation Codes in Canada.
NOTINTENDED FOR USEAS A PRIMARYHEAT SOURCE.
Thisapplianceistestedandapprovedaseithersupplemental
room heat or as a decorative appliance. It should not be fac-
tored as primary heat in residential heating calculations.
Listing and Code Approvals
C. High Altitude Installations
U.L.Listed gasappliancesaretestedand approvedwithout
requiring changes for elevations from 0 to 2000 feet in the
U.S.A. and Canada.
When installing this appliance at an elevation above 2000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above
a 2000 foot elevation in the U.S.A., or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating
value of the gas has been reduced, these rules do not
apply. To identify the proper orifice size, check with the
local gas utility.
If installing this appliance at an elevation above 4500 feet
(in Canada), check with local authorities.
B. BTU Specifications
1
MODELS: 6000GLX-IPI-R, 6000GLX-IPI-S,
6000GLX-IPILP-R, 6000GLX-IPILP-S
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Appliance Heater
STANDARD: ANSI Z21.88-2000•CSA2.33-M98•UL307B
WARNING
DoNOTusethisapplianceifany part has beenunderwater.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burn-
ing Heating Appliances for Manufactured Homes and
RecreationalVehicles”,and “GasFiredAppliancesfor Use
at High Altitudes”.
Heat & Glo Quality Systems
registered by SGS ICS
Models
U.S. (0-2000 FT) or Canada (2000-4500 FT)
Maximum
Input
BTUH
Minimum
Input
BTUH
Orifice
Size
(DMS)
6000GLX-IPI-R (NG)
6000GLX-IPI-S (NG)
US 40,000 18,700 39
53 (2)
CANADA 36,000 16,830 40
54 (2)
6000GLX-IPILP-R
6000GLX-IPILP-S
US 36,000 16,500 54
68 (2)
CANADA 32,400 14,850 55
69 (2)
A. Appliance Certification
D. Non-Combustible Materials Specification
Materialwhichwill notigniteand burn.Such materials are
thoseconsistingentirely ofsteel, iron, brick,tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in
a Vertical Tube Furnace at 750oC, shall be considered
non-combustible materials.
E. Combustible Materials Specification
Materials made of or surfaced with wood, compressed
paper, plant fibers, plastics, or other material that can
ignite and burn, whether flame proofed or not, or whether
plastered or unplastered shall be considered combustible
materials.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 5
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where
the side wall exhaust vent termination is less than seven
(7) feet above finished grade in the area of the venting,
includingbut notlimited todecksandporches,the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gasfitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the
floor level where the gas equipment is to be installed. In
addition, the installing plumber or gasfitter shall observe
that a battery operated or hard wired carbon monoxide
detector with an alarm is installed on each additional level
of the dwelling, building or structure served by the side
wallhorizontal vented gasfueled equipment.It shall bethe
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
Inthe eventthatthesidewall horizontallyvented gasfueled
equipmentisinstalled inacrawl spaceoran attic,thehard
wired carbon monoxide detector with alarm and battery
back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
ownershallhave aperiod of thirty(30) daystocomply with
the above requirements; provided, however, that during
said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Eachcarbon monoxidedetectoras requiredin accordance
with the above provisions shall comply with NFPA720 and
be ANSI/UL 2034 listed and IAS certified.
Signage
Ametal or plastic identification plate shall be permanently
mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with
the exhaust vent terminal for the horizontally vented gas
fueled heating appliance or equipment. The sign shall
read, in print size no less than one-half (1/2) inch in size,
“GAS VENT DIRECTLY BELOW. KEEP CLEAR OFALL
OBSTRUCTIONS”.
Inspection
Thestate orlocalgas inspectorof theside wallhorizontally
vented gas fueled equipment shall not approve the
installationunless, uponinspection, theinspector observes
carbon monoxide detectors and signage installed in
accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• Theequipmentlisted inChapter 10 entitled“Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas
fueled equipment installed in a room or structure
separate from the dwelling, building or structure used
in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontallyvented gas fueledequipment doesnot provide
the parts for venting the flue gases, but identifies “special
venting systems”, the following requirements shall be
satisfied by the manufacturer:
• The referenced “special venting system” instructions
shallbe included withthe applianceor equipment instal-
lation instructions; and
• The“special ventingsystems”shall beProductApproved
bythe Board,andthe instructionsforthatsystemshall in-
clude a parts list and detailed installation instructions.
A copy of all installation instructions for all Product Ap-
provedside wallhorizontallyvented gasfueled equipment,
all venting instructions, all parts lists for venting instruc-
tions, and/or all venting design instructions shall remain
with the appliance or equipment at the completion of the
installation.
See Gas Connection section for additional Common-
wealth of Massachusetts requirements.
F. Requirements for the Commonwealth of
Massachusetts
NOTE: The following requirements reference various
Massachusetts and national codes not contained in
this document.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
6
A. Design and Installation Considerations
Heat & Glo direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
thebuildingand allexhaustgases expelledto the outside.
No additional outside air source is required.
Getting Started
C. Inspect Appliance and Components
2
When planning an appliance installation, it’s necessary to
determine the following information before installing:
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping.
• Electrical wiring.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
B. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Reciprocating saw Framing material
Pliers Hi temp caulking material
Hammer Gloves
Phillips screwdriver Framing square
Flat blade screwdriver Electric drill and bits (1/4 in.)
Plumb line Safety glasses
Level Manometer
Voltmeter Tape measure
Noncorrosive leak check solution
1/2 - 3/4 inch length, #6 or #8 Self-drilling screws
One 1/4 inch female connection (for optional fan).
• Carefully remove the appliance and components from
the packaging.
• Theventsystemcomponentsandtrimdoorsareshipped
in separate packages.
• The gas logs may be packaged separately and must
be field installed.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
• Read all of the instructions before starting the in-
stallation. Follow these instructions carefully dur-
ing the installation to ensure maximum safety and
benefit.
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
CAUTION
Keep appliance dry.
• Mold or rust may cause odors.
• Water may damage controls.
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
WARNING
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
• Installation and use of any damaged
appliance or vent system component.
WARNING
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
Any such action may cause a fire hazard.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 7
3Framing and Clearances
NOTE:
•Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
•Illustrations/diagrams are not drawn to scale.
•Actual installation may vary due to individual design
preference.
WARNING
Fire Risk
Provide adequate clearance:
• Around air openings
• To combustibles
• For service access
Locate appliance away from traffic areas.
A. Selecting Appliance Location
Whenselecting alocation foryour applianceit isimportantto
consider the required clearances to walls (see Figure 3.1).
Figure 3.1 Appliance Locations
NOTE: For actual appliance dimensions refer to Sec-
tion 16.
In addition to these framing dimensions, also reference the following sections:
• Clearances and Mantel Projections (Sections 3.C and 3.D)
• Vent Clearances and Framing (Section 6).
ABC D E F G H
Inches 51 42 72 56-5/8 See Section D.
Mantel Projections 22 17-3/4 8
Millimeters 1295 1067 1829 1438 559 451 203
1/2 IN.
REAR VENT,
HORIZONTAL TERMINATION,
TWO ELBOWS REAR VENT,
NO ELBOWS
REAR VENT,
ONE ELBOW
ALCOVE
INSTALLATION
TOP VENT
ONE 90º ELBOW
A
A
BC
B
E
D
B
D
B
B
D
D
F
G
H

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
8
Fire Risk.
•Construct chase to all clearance
specifications in manual.
•Locate and install appliance to all
clearance specifications in manual
WARNING
B. Constructing the Appliance Chase
A chase is a vertical boxlike structure built to enclose the
gasappliance and/orits ventsystem. Verticalvents thatrun
on the outside of a building may be, but are not required to
be, installed inside a chase.
Construction of the chase may vary with the type of building.
These instructions are not substitutes for the requirements
of local building codes. Local building codes MUST be
checked.
Chasesshouldbe constructed inthe manner ofall outside
walls of the home to prevent cold air drafting problems.
The chase should not break the outside building envelope
in any manner.
Walls, ceiling, base plate and cantilever floor of the chase
shouldbe insulated.Vapor andairinfiltrationbarriersshould
beinstalled inthechaseasper regionalcodes fortherest of
the home.Additionally, in regions where cold air infiltration
may be an issue, the inside surfaces may be sheetrocked
and taped for maximum air tightness.
To further prevent drafts, the wall shield and ceiling
firestops should be caulked with high temperature caulk
to seal gaps. Gas line holes and other openings should
C. Clearances
Figure 3.2 Clearances to Combustibles
Fire Risk.
Odor Risk.
•Install appliance on hard metal or wood
surfaces extending full width and depth of
appliance.
•Do NOT install appliance directly on
carpeting, vinyl, tile or any combustible
material other than wood.
WARNING
be caulked with high temp caulk or stuffed with unfaced
insulation. If the appliance is being installed on a cement
slab, a layer of plywood may be placed underneath to
prevent conducting cold up into the room.
C
B
D
A
G
I
H
E
FJ
Clearance to Combustibles
ABCDE F G HIJ
Rough
Opening
(Vent Pipe)
Rough
Opening
(Height)
Rough
Opening
(Depth)
Rough
Opening
(Width) Clearance
to Ceiling Combustible Floor Combustible Flooring Behind Appliance Sides of Appliance Front of Appliance
Inches 10 38-1/2 22 42 26 5/8 0 0 1/2 1/2 36
Millimeters 254 978 559 1067 676 0 0 13 13 915

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 9
D. Mantel Projections
Figure 3.3 Clearances to Mantels or other
Combustibles above Appliance
Figure 3.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
MEASUREMENTS FROM
TOP EDGE OF THE OPENING
510 11 12
2-1/2
13 14
15 16 17 18 19
32
TO CEILING
91011 12
8
7
6
5
4
3
25
18
A
Top View
INTERIOR WALL
FIREPLACE
OPENING
B
MANTEL LEG OR WALL PROJECTIONS
Note: All measurements in inches.
If Aminimum is ____, then Bmaximum is_____.
AInches 2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16
Millimeters 62 87 113 138 164 189
BInches 12345
∞
Millimeters 25 51 76 102 127 ∞
NOTE: Measurement is taken from top of the
opening, NOT the top of the fireplace.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
10
A. Vent Termination Minimum Clearances
Fire Risk.
Explosion Risk.
Maintain vent clearance to combustibles as
specified.
WARNING
• Do not pack air space with insulation or
other materials.
Failure to keep insulation or other materials
away from vent pipe may cause fire.
Roof Pitch H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12.................................................1.25*
Over 7/12 to 8/12.................................................1.5*
Over 8/12 to 9/12.................................................2.0*
Over 9/12 to 10/12...............................................2.5
Over 10/12 to 11/12.............................................3.25
Over 11/12 to 12/12.............................................4.0
Over 12/12 to 14/12.............................................5.0
Over 14/12 to 16/12.............................................6.0
Over 16/12 to 18/12.............................................7.0
Over 18/12 to 20/12.............................................7.5
Over 20/12 to 21/12.............................................8.0
Figure 4.1
Figure 4.2 Minimum Height from Roof to
Lowest Discharge Opening
Termination Locations
4
Measure horizontal clearances from this surface.
Measure vertical clearances from this surface.
Figure 4.3 Multiple Vertical Termination
Figure 4.2 specifies minimum vent heights for various
pitched roofs.
(See Figure 4.4 for specific clearances)
* 3 foot minimum in snow regions
HORIZONTAL
OVERHANG
VERTICAL
WALL
GAS DIRECT VENT
TERMINATION CAP
12
X
ROOF PITCH
IS X/ 12
LOWEST
DISCHARGE
OPENING
2 FT.
MIN.
20 INCHES MIN.
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
C
A
GAS
TERMINATION
B
GAS, WOOD OR FUEL
OIL TERMINATION
Gas
Termination Wood & Fuel Oil Termination Comments
A6 in. 20 in. min. Horizontal distance between terminations
B20 in. 24 in. min. Distance to perpendicular wall
C18 in. 18 in. Vertical distance between terminations
Fire Risk.
Explosion Risk.
Inspect external vent cap regularly.
• Ensure no debris blocks cap.
• Combustible materials blocking cap may
ignite.
• Restricted air flow affects burner operation.
WARNING
Î

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 11
V= VENT TERMINAL X= AIR SUPPLY INLET = AREA WHERE TERMINAL IS NOT PERMITTED
Figure 4.4 Minimum Clearances for Termination
A = 12 inches...............clearancesabovegrade,veranda,
porch, deck or balcony
B = 12 inches...............clearances to window or door
thatmay be opened, or toperma-
nently closed window. (Glass)
D* = 18 inches...............vertical clearance to unventilated
soffitortoventilated soffit located
above the terminal
*30 inches..............for vinyl clad soffits and below
electrical service
F = 9 inches................clearance to outside corner
G = 6 inches.................clearance to inside corner
H = 3 ft. (Canada)........not to be installed above a gas
meter/regulator assembly within 3
feet (90cm) horizontally from the
center-line of the regulator
I = 3 ft. .......................clearanceto gasserviceregulator
vent outlet
J = 9 inches (U.S.A.)
12 inches (Canada) clearance to non-mechanical
air supply inlet to building or the
combustion air inlet to any other
appliance
K = 3 ft. (U.S.A.)
6 ft. (Canada)...........clearance to a mechanical
(powered) air supply inlet
L** = 7 ft...........................clearance above paved
sidewalk or a paved driveway
located on public property
M*** = 18 inches.................clearance under veranda, porch,
deck, balcony or overhang
42 inches ................vinyl
CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE INSTALLED.
** avent shall notterminate directly abovea sidewalk orpaved driveway
whichis locatedbetween twosingle familydwellings and serves both
dwellings.
*** only permitted if veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor, or meets Note 2.
NOTE 1: On private property where termination is less than 7 feet above
a sidewalk, driveway, deck, porch, veranda or balcony, use of a listed cap
shield is suggested. (See vents components page)
NOTE 2: Termination in an alcove space (spaces open only on one side
and with an overhang) are permitted with the dimensions specified for
vinyl or non-vinyl siding and soffits. 1. There must be 3 feet minimum
between termination caps. 2. All mechanical air intakes within 10 feet
of a termination cap must be a minimum of 3 feet below the termination
cap. 3. All gravity air intakes within 3 feet of a termination cap must be a
minimum of 1 foot below the termination cap.
(See Note 1)
(See Note 1)
(See Note 2)
NOTE 3: Local codes or regulations may require different
clearances.
NOTE 4: Termination caps may be hot. Consider their proximity to
doors or other traffic areas.
NOTE 5: Location of the vent termination must not interfere with
access to the electrical service.
WARNING: In the U.S: Ventsystemtermination isNOT permittedin
screenedporches.You must follow side wall, overhangand ground
clearances as stated in the instructions.
In Canada: Vent system termination is NOT permitted in screened
porches. Vent system termination is permitted in porch areas with
two or more sides open. You must follow all side walls, overhang
and ground clearances as stated in the instructions.
Heat& Gloassumes no responsibility for theimproper performance
of the appliance when the venting system does not meet these
requirements.
QMIN = # termination caps x 3 RMAX = (2 / # termination caps) x QACTUAL
N = 6 inches ..................non-vinyl sidewalls
12 inches ................vinyl sidewalls
P = 8 ft.
Alcove Applications
S = 6 inches...................clearance from sides of elec-
trical service
T = 12 inches..................clearance above electrical
service
(See Note 5)
(See Note 5)
Electrical
Service
V
S
VS
V
T
D*
V
MN
P
R
Q
QMIN RMAX
1 cap 3 feet 2 x Q ACTUAL
2 caps 6 feet 1 x Q ACTUAL
3 caps 9 feet 2/3 x Q ACTUAL
4 caps 12 feet 1/2 x Q ACTUAL

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
12
5Vent Information and Diagrams
Fire Hazard.
Explosion Risk.
Asphyxiation Risk.
Do NOT connect this gas appliance to a
chimney flue serving a separate solid-fuel or
gas burning appliance.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
May impair safe operation of this appliance or
other appliances connected to the flue.
WARNING
CAUTION
ALL vent configuration specifications MUST be followed.
• This product is tested and listed to these
specifications.
• Appliance performance will suffer if specifications are
not followed.
B. Use of Elbows
Diagonal runs have both vertical and horizontal vent as-
pects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 5.1).
Two450elbowsmay beused inplaceof one900elbow.On
450runs, one foot of diagonal is equal to 8.5 inches hori-
zontal run and 8.5 inches vertical run. A length of straight
pipe is allowed between two 450elbows (see Figure 5.1).
Figure 5.1
A. Vent Table Key
The abbreviations listed in this vent table key are used in
the vent diagrams.
C. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
1. Pipemeasurementsareshownusingtheeffectivelength
of pipe (see Figure 5.2).
2. Measurementsaremadefrom theappliance outerwrap,
not from the standoffs.
3. Horizontal terminations are measured to the outside
mountingsurface (flangeofterminationcap)(see Figure
4.1).
4. Vertical terminationsaremeasuredtobottom oftermina-
tion cap.
5. Horizontal pipe installed level with no rise.
Figure 5.2 DVP Pipe Effective Length
Effective
Height/Length
Symbol Description
V1First section (closest to appliance of vertical length
V2Second section of vertical length
H1First section (closest to appliance) of horizontal length
H2Second section of horizontal length
Horizontal
V
ertical
8-1/2 in.
8-1/2 in.
12 in.
Pipe Effective Length
Inches Millimeters
DVP4 4 102
DVP6 6 152
DVP12 12 305
DVP24 24 610
DVP36 36 914
DVP48 48 1219
DVP6A 3 to 6 76 to 152
DVP12A 3 to 12 76 to 305
DVP12MI 3 to 12 76 to 305
DVP24MI 3 to 24 76 to 610

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 13
Figure 5.3
Figure 5.4
D. Vent Diagrams
WARNING
1. Top Vent - Horizontal Termination
One Elbow
Two Elbows
NOTE: For corner installations: A 6 inch
(152mm) section of straight pipe may need
to be attached to the appliance before a
90o elbow, to allow the vent pipe to clear
the top standoffs.
NOTE: For corner installations: A
6 inch (152mm) section of straight
pipe may need to be attached to
the appliance before a 90o elbow, to
allow the vent pipe to clear the top
standoffs.
V1Minimum H1Maximum
Elbow only 2 ft 610 mm
1 ft. 305 mm 3 ft. 914 mm
2 ft. 610 mm 6 ft. 1.8 m
3 ft. 914 mm 11 ft. 3.4 m
4 ft. 1.2 m 20 ft. 6.1 m
V1+ H1= 40 ft. (12.2 m) Maximum
H1= 20 ft. (6.1 m) Maximum
V1Minimum H1+ H2Maximum
Elbow only 1 ft. 305 mm
6 in. 152 mm 2 ft. 610 mm
1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 4 ft. 1.2 m
3 ft. 914 mm 9 ft. 2.7 m
4 ft. 1.2 m 18 ft. 5.5 m
5 ft. 1.5 m 20 ft. 6.1 m
V1+ H1 + H2= 40 ft. (12.2 m) Maximum
H1 + H2= 20 ft. (6.1 m) Maximum
Fire Risk. Explosion Risk.
Do NOT pack insulation or other combustibles
between ceiling firestops.
• ALWAYS maintain specified clearances
around venting and firestop systems.
• Install wall shield and ceiling firestops as
specified.
Failure to keep insulation or other material
away from vent pipe may cause fire.
NOTE: The 6000 series fireplaces can adapt
to SL series vent pipe, if desired.
Whenventing offthe topof theunit, useaDVP-2SLadapter
and a minimum 48 inch vertical section of SL series vent
pipe.
After the 48 inch vertical section, the venting table rules
must be followed. The first 48 inch vertical section is NOT
countedas part ofthe vertical componentsinthe table.It is
still counted as part of the overall maximum run.All venting
table rules for the vent run must still be followed.
Example: DVP pipe 3 ft. min. vertical = 11 ft. max. horizontal
SL pipe 7 ft. min. vertical = 11 ft. max. horizontal
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZC-
SStermination caps on topvented fireplaces,a
6inch minimum vertical vent section isrequired
before installing first elbow.
WARNING
Î

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
14
Figure 5.5
1. Top Vent - Horizontal Termination - (continued)
Three Elbows V1Min. H1Max. V2Min. H2Max.
Elbow only 2 ft. 610 mm 0 in. 0 mm 1 ft. 305 mm
6 in. 152 mm 3 ft 914 mm 6 in. 152 mm 2 ft. 610 mm
1 ft. 305 mm 6 ft. 1.8 m 1 ft. 305 mm 6 ft. 1.8 m
2 ft. 610 mm 11 ft.* 3.4 m* 2 ft. 610 mm 10 ft.* 3.1 m*
3 ft. 914 mm 16 ft * 4.9 m* 3 ft. 914 mm 14 ft.* 4.3 m*
*H1+ H2= 20 ft. (6.1 m) Maximum V1+ V2+ H1+ H2 = 40 ft. (12.2m) Maximum
Fire Risk.
• When using DVP-HRC-SS and DVP-HRC-ZC-
SStermination caps on topvented fireplaces,a
6inch minimum vertical vent section isrequired
before installing first elbow.
WARNING

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 15
2. Top Vent - Vertical Termination
No Elbow
NOTE: If installing a vertical vent/
termination off the top of the appli-
ance, the optional vertical termina-
tion baffle should be used.
V1= 40 ft. Max. (12.4 m)
V1= 3 ft. Min. (914mm)
Flue Restrictor Instructions
1. Remove the top piece of refractory, if already installed
(see Figure 5.7).
Figure 5.8 Flue Restrictor
2. Break the Flue Restrictor into two pieces. Do this by
bending the part back and forth until it breaks (see
Figure 5.8).
Figure 5.6
Figure 5.7
BREAK
HERE
TOP
REFRACTORY FLUE
RESTRICTOR

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
16
Figure 5.11
Two Elbows V1 H
1 Maximum V2V1 + V2 Min.
Elbow only 2 ft. 610 mm * * *
6 in. 152 mm 6 ft. 1.8 m * * *
2 ft. 610 mm 11 ft. 3.4 m * * *
3 ft. 914 mm 16 ft. 4.9 m * * *
4 ft. 1.2 m 20 ft 6.1 m * * *
V1 + V2 + H1 = 50 ft (15.2 m) Maximum
*No specific restrictions on this value EXCEPT
V1 + V2 + H1 cannot exceed 50 ft (15.2 m)
Figure 5.10
4. Center the Flue Restrictor on vent and secure in place
by using two self-tapping screws (see Figure 5.10).
3. Match the amount of vertical you have in the sys-
tem with the chart to find the appropriate position
to set the Flue Restrictor (see Figure 5.9).
Figure 5.9
1 2 3 4 5
SETTINGS
1 2 3 4 5
Vertical TOP VENT REAR VENT
NG LP NG LP
4 ft. 1-1 No
Restrictor No Restrictor No Restrictor
8 ft. 2-2 1-2 1-1 No
Restrictor
15 ft. 3-3 3-2 2-2 1-2
20 ft. 3-4 3-3 3-3 2-3
25 ft. 3-4 3-3 3-3 2-3
30 ft. 4-4 3-4 3-4 3-3
35 ft. 4-4 3-4 3-4 3-3
40 ft. 5-4 4-4 4-4 3-4
Note: If the DVP-2SL adapter and SL pipe is used, you MUST subtract one number from the table above. Example: Top
vent 40 ft. vertical with DVP pipe = 5-4. Top vent 40 ft. vertical with SL pipe = 4-3.
Î

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 17
INSTALLED
HORIZONTALLY
Figure 5.12
2. Top Vent - Vertical Termination - (continued)
Three Elbows V1 H
1+ H2 V2V1 + V2 Minimum H 1+ H2 Maximum
Elbow only 1 ft. 305 mm * * * 1 ft. 305 mm
6 in. 152 mm 2 ft. 610 mm * * * 2 ft. 610 mm
1 ft. 305 mm 2 ft. 610 mm * * * 2 ft. 610 mm
2 ft. 610 mm 4 ft. 1.2 m * * * 4 ft. 1.2 m
3 ft. 914 mm 9 ft. 2.7 m * * * 9 ft. 2.7 m
4 ft. 1.2 m 18 ft. 5.5 m * * * 18 ft. 5.5 m
H1+ H2 = 20 ft (6.1m) Maximum V1+ V2 + H1+ H2= 40 ft (12.2m) Maximum

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
18
3. Rear Vent - Horizontal Termination
Figure 5.13
Figure 5.14
No Elbow
One 450Elbow
H1= 16 in. (406 mm) Maximum
Do not use a 450elbow in corner installations.
Use two 900elbows instead.

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07 19
3. Rear Vent - Horizontal Termination - (continued)
Two Elbows
Figure 5.15
Figure 5.16
Three Elbows
INSTALLED
HORIZONTALLY
H1 Maximum V1 Minimum H2H1+ H2 Maximum
1 ft. 305 mm Back to Back
90º Elbows 1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 in. 152 mm 2 ft. 610 mm 4ft 1.2 m
3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m
3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m
3 ft. 914 mm 4ft 1.2 m 18 ft. 5.5 m 20 ft.* 6.1 m*
V1+ H1+ H2= 40 ft (12.2m) Maximum H1= 3 ft (914mm) Maximum
*H1+ H2= 20 ft (6.1m) Maximum
H1 Maximum V1 Minimum H2+ H3H1+ H2+ H3 Maximum
1 ft. 305 mm Back to Back
90º Elbows 1 ft. 305 mm 2 ft. 610 mm
2 ft. 610 mm 6 in. 152 mm 1.5 ft. 457 mm 3.5 ft. 1.0 m
3 ft. 914 mm 1 ft. 305 mm 2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 2 ft. 610 mm 4 ft. 1.2 m 7 ft. 2.1 m
3 ft. 914 mm 3 ft. 914 mm 9 ft. 2.7 m 12 ft. 3.7 m
3 ft. 914 mm 4 ft. 1.2 m 12 ft. 3.7 m 15 ft. 4.6 m
V1+ H1+ H2+ H3= 40 ft (12.2m) Maximum H1= 3 ft (94mm) Maximum
H1+ H2+ H3= 20 ft (6.1m) Maximum

Heat & Glo • 6000GLX-IPI-S/-R, 6000GLX-IPILP-S/-R • 2101-900 Rev. K • 12/07
20
INSTALLED
HORIZONTALLY
4. Rear Vent - Vertical Termination
One Elbow
Figure 5.17
Two Elbows
Figure 5.18
V1 Minimum H1 Maximum
6 in. 152 mm 2 ft. 610 mm
1 ft. 305 mm 3 ft. 914 mm
2 ft. 610 mm 5 ft. 1.5 m
3 ft. 914 mm 7 ft. 2.1 m
4 ft. 1.2 m 8 ft 2.4 m
5 ft. 1.5 m 8ft 2.4 m
V1+ H1 = 40 ft (12.2 m) Maximum
H1 = 8 ft (2.4 m) Maximum
H1+ H2 Maximum V1 Minimum
Back to Back 90° Elbows 3 ft. 914 mm
2 ft 610 mm 6 ft. 1.8 m
4 ft 1.2 m 9 ft. 2.7 m
6 ft. 1.8 m 12 ft. 3.7 m
8 ft. 2.4 m 15 ft. 4.6 m
V1+ H1= 40 ft (12.2 m) Maximum
H1+ H2= 8 ft (2.4 m) Maximum