Heat & Glo LOGS-2531 User manual

1
Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 1. Log Identication
Figure 3. Log #1 Installed
CAUTION: Logs are fragile, handle with care.
NOTICE: To simplify the installation process, use
Figure 1 to positively identify each individual log
before beginning installation.
Figure 2. Empty Firebox with Front Hearth Installed
LOG #1: Locate the cutout on Log #1, place it over the pilot hood and set the log on the left side of the rebox. Rotate Log
#1 clockwise until it contacts log pin A and the rebox wall. Ensure that the end of Log #1 is in contact with the air scoop.
See Figure 3.
LOGS-2531, LOGS-2532, LOGS-2533
MODELS: SUPREME-I25-IFT, SUPREME-I30-IFT, SUPREME-I35-IFT, I30X-AU
Installation Instructions
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
Leave this manual with party responsible for use
and operation.
MODEL: SUPREME-I25-IFT
PILOT HOOD
AIR SCOOP
1
A
12345
SUPREME-I25-IFT SRV LOGS
LOG ID SRV PART # MOLDED LOG #
1SRV2531-711 31-1
2 SRV2531-712 31-2
3SRV2531-713 31-3
4SRV2531-714 31-4
5 SRV2531-715 31-5
B
C
LOG #2: Set Log #2 on the burner between pins B and C. Rotate the log counter clockwise until it contacts both pins B and
C and slide it back until it contacts the Air Scoop. Ensure Log #2 is not covering any ports. See Figure 4.
Figure 4. Log #2 Installed
2
SHOULDER SCREW
AIR SCOOP
B
AC

2Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 7. Log #5 Installed
LOG #5: Place the non-bark end of log 5 on the at spot of log 3. The front right corner on the other end of log 5 will sit at
the intersection of the grout lines on the base refractory. See Figure 7.
Figure 6. Log #4 Installed
Figure 5. Log #3 Installed
23
LOG #3: With the burnout of Log #3 facing left, line the big end up with the edge of the basepan and the rebox wall or
refractory. The small end will sit half on the end of Log #2 and half on the air scoop as shown in Figure 5.
1
4
2
5
3
LOG #4: The Y-end of Log #4 should sit on the at spot of Log #2, the other end will sit on the at spot of Log #1. See Figure 6
GROUT LINE

3
Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 11. Empty Firebox with Front Hearth Installed
Figure 12. Log #1 Installed Figure 13. Log #2 Installed
MODELS: SUPREME-I30-IFT, I30X-AU
PILOT HOOD
AIR SCOOP
LOG #1: Locate the cutout on the end of log 1 and place over the pilot hood and air scoop. The other end of Log #1 will sit
against log pin A. See Figure 12.
LOG #2: With the bark end of Log #2 towards the back of the rebox, set the log onto the burner behind log pins B and C
as shown in Figure 13. Rotate the log counter clockwise so that it contacts the air scoop, along with pins B and C.
AIR SCOOP
1
2
A
C
Figure 10. Log Identication
12345
B
C
NOTICE: To simplify the installation process, use Figure 10 to positively identify each individual log before beginning
installation.
SUPREME-I30-IFT, I30X-AU SRV LOGS
LOG ID SRV PART # MOLDED LOG #
1SRV2532-711 32-1
2 SRV2532-712 32-2
3SRV2532-713 32-3
4SRV2532-714 32-4
5 SRV2532-715 32-5
BD
A

4Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 16. Log #5 Installed
LOG #5: The non-burnout end of log 5 will sit on the at spot of log 3. The corner of the other end will sit on the base
refractory grout line. See Figure 16.
3
5
Figure 15. Log #4 Installed
2
14
LOG #4: Set the non-Y end of Log #4 on the at spot of Log #1. The end of the log #4 will sit ush with the back of Log #1.
The Y-end of log #4 will sit on the at spot of Log #2. See Figure 15.
LOG #3: With the burnout of Log #3 facing left, set the large end against log pin D, place the small end on the at spot of
Log #1. See Figure 14.
Figure 14. Log #3 Installed
123
D
GROUT LINE
4

5
Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 18. Empty Firebox with Front Hearth Installed
Figure 19. Log #1 Installed Figure 20. Log #2 Installed
MODELS: SUPREME-I35-IFT
PILOT HOOD
AIR SCOOP
LOG #1: Locate the cutout on the end of Log #1. The other end of Log #1 will set between log pins A and B. Rotate the
cut-out end back until the cut-out fully engages the air scoop. See Figure 19.
LOG #2: The short side of the Y on Log #2 will sit between log pins D and E, the long end of the Y will sit against log pin C.
The opposite end of Log #2 will sit on the air scoop. See Figure 20.
1 2
AC
Figure 17. Log Identication
12345
D
C
NOTICE: To simplify the installation process, use Figure 17 to positively identify each individual log before beginning
installation.
SUPREME-I35-IFT SRV LOGS
LOG ID SRV PART # MOLDED LOG #
1SRV2533-711 33-1
2 SRV2533-712 33-2
3SRV2533-713 33-3
4SRV2533-714 33-4
5 SRV2532-715 33-5
6 SRV2538-715 33-5
BD
A
E
F
G
B
AIR SCOOP
6
H

6Heat & Glo • LOGS-2531, LOGS-2532, LOGS-2533 Installation Instructions • 2532-935 Rev. C • 3/19
Figure 23. Log #5 Installed
LOG #5: The non-burnout end of Log #5 will sit on the at spot of Log #3. The corner of the other end will sit on the base
refractory grout line. See Figure 23.
3
5
Figure 22. Log #4 Installed
2
14
LOG #4: Set the non-Y end of log 4 on the at spot of Log #1. The end of Log #4 will sit ush with the back of Log #1. The
Y-end of Log #4 will sit on the at spot of Log #2. See Figure 22.
LOG #3: With the burnout facing left, place the big end of Log #3 against log pin F and slide back until it contacts log pin G
as shown in Figure 21. The small end will sit on the at spot of Log #2.
Figure 21. Log #3 Installed
23
F
G
Figure 24. Log #6 Installed
3
5
H
Figure 25. Log #6 Installed
3
6
H
LOG #6: Slide the burn out end of Log #6 between log #5 and log #3. Push the log back until it touches the rebox. The
left side will touch pin H. The right side of the log touches Log #3. See Figures 24 and 25.
5
6