Heat Outdoors QHVCR User manual

QHVCR 3 Zone Master Controller
(Transmitter)
Remote Operation
Quick Start Guide & nstructions
Transmission RF 433 Mhz

QHVCR 3 Zone
Master Controller (Transmitter)
Antenna
Power ON / Standby ndicator
ON / Standby Switch
Power control dials for
Blue, Red & Yellow zones
QHVCR is Supplied separately Fig 1
1) There are three control dials Blue, Yellow & Red one for each zone. The QHCxx R units are preset
to operate in one of these zones. The QHCxx R unit once preset will only operate in that designated
zone. The factory setting is 1, this will be the Blue control dial.
2) Turn ON the QHVCR unit by pressing the ON/Standby button on the front panel. The Led indicator
will flash orange – green – orange – green and remain Green to indicate that the unit is ready see fig 1.
3) The QHCxx R unit is preset as a Blue zone (1). Turn the Blue control dial to position 2. The heaters
connected to the QHCxx R units will come ON at the minimum setting 33%. Continue to turn the Blue
control dial through position 3 to 5 until you reach the desired setting. Settings are 1 = 0%, 2 = 33%, 3 =
50%, 4 = 66% & 5 = 100%.
4) QHCxx R units which are preset to Yellow & Red zones are controlled by the Yellow & Red control
dials respectively and will operate as above see fig's 2 & 3.
5) The QHVCR unit is powered by 3 x AAA battery's. The unit will automatically go into standby mode
if the unit is inactive for more than 30 seconds. When the unit goes into standby mode all the QHCxx R
units will remain unchanged at the settings they were set at. Therefore the heaters will remain ON.
6) To change a setting just press the ON/Standby button and proceed as described in 2) & 3).
However, while the QHVCR unit is ON, you can turn OFF all the heaters by pressing the ON/Standby
button. This is indicated by the Led indicator flashing Red.
7) The previous settings will be remembered and will be restored when you press the ON/Stand by button
again.
Please note: The QHVCR 3 zone aster Controller can control any number of
QHCxx R controllers as long as they are within range, up to 100 meters *
The QHVCR should be wall mounted.
* Longer antenna are available to extend the range up to 200 meters.
Page 2

Pairing (Programming) Devices
QHVCR & QHCxxMR
Fig. 2 Fig. 3
Pairing (programming) devices QHVCR (transmitter) and QHC18MR (receivers).
1) The Left Hand Side rotary switches (TEN) on both boards must be set the same, Fig 2.
The LHS switch (TEN) is used to set the RF frequency the setting must match on both
boards. There are 10 possible frequencies that can be selected 0-9. If the settings on the LHS
switch (TEN) do not match the devices will fail to operate.
Designating the transmitter and receiver. Both the left rotary switches are set at 0,
this ensures that the transmitter marked 0 will communicate with the receiver marked 0.
Setting the left rotary switch to 1, so the transmitter marked 1 will communicate with a
receiver also marked 1.
If the transmitter and receiver are not paired correctly they will not communicate and
therefore will not operate; transmitter marked 0 will not communicate with a
receiver marked 1.
Remember a transmitter can be set at any number between 0-9 & the receiver must be
matched correctly.
2) The Right Hand Side rotary switches (UNIT) are for setting the devise to operate in a set zone, Fig 3.
There are 3 possible zones that the controller can be set to. The RHS switch (UNIT) should be set to
1,2 or 3.
Blue Zone 1 operation set RHS switch (UNIT) to 1
Yellow Zone 2 operation set RHS switch (UNIT) to 2
Red Zone 3 operation set RHS switch (UNIT) to 3
Note : QHCxxMR = QHC03MR, QHC06MR or QHC18MR
Page 3

CE RoHS Technical Data
Supply voltage : 4.5V DC Battery : 3 x AAA batteries
Transmission : RF 433 Mhz
Range : Up to 100 meters standard
Antenna : 100mm standard
Freq. combinations : 10
Zones : 3 standard (maximum 10)
Mounting : L Brackets included – fixing centers 65mm
P Rating: P53
Dimensions : 165mm x 105mm x 55mm
Weights : 0.25 Kg
Tel. [phone] Email: [email protected]
Website: www.heat-outdoors.co.uk
Unit 9 Stort Valley Industrial Estate, Bishop's Stortford, Hertfordshire, CM23 2TU, UK