Heater Sports Batter Up User manual

IMPORTANT
DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE
PURCHASED. CALL TOLL FREE: [phone]
WARNING:
Improper use of this product can result is serious injury. Read and follow the instructions
for the proper and safe use of the Batter Up. Always wear a helmet with a guard.
Adult supervision is required. Inspect the Perfect Swing, rubber bands, base, clamps, etc., before
each use for evidence of any damage. Keep the area clear with-in 24 ft. of the device and
around the swinging area of the batter. Always hit the ball toward an open unoccupied area.
Make sure all knobs and clamps are tightly and securely fastened. Never hit toward
another person. Do not use if damaged or broken.
Instructions
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]
®
Follow All Instructions Before Assembling Or Using This Product

95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]
®
L - Base
F
A
B - Center Pole
C
D
E
K- Perfect Swing
A - Large Metal Washer
B - Center Pole
C - Rubber Washers (x2)
D - Base Bolt
E - Lock Washer
F - Bolt Wrench
G - Tension Rubber Bands (x10)
H - Base Insert Tube
I - Ground Stakes (x3)
J - Batter Up Decal
K - Perfect Swing Batting Stick
L - Base
G
H
I - Ground Stakes
J
Model# BU99
Part List

Slide one of the Part C (Rubber Washers) over
the bottom end of Part B (Center Pole).
Next slide Part H (Base Insert Tube) over the
bottom end of Part B.
Then insert the bottom end of Part B into the
top of the center hole of the Base as seen in
Figure 1.
1 -
Now place Part A (Large Metal Washer) on the bottom side of the Base
over the center hole where Part B was inserted as seen in Figure 2.
2 -
Place Part E (Lock Washer) on top of Part A and insert Part D (Base
Bolt) through the washers and into Part B in the bottom of the Base as
seen in Figure 3.
3 -
Figure 1
Assembly Instructions
Figure 2
Figure 3
C HB

Securely tighten Part D with the supplied (Bolt Wrench) Part F as
shown in Figure 4.
Note: Tighten the Bolt enough to keep the pole from twisting when
the ball is hit. Do Not Overtighten the Bolt.The Bolt (Part D) should
not touch the ground surface when the Base is placed upright.
WARNING: Be careful when placing the Base and Pole right-side-up,
especially when the Base is full.When weighted the Pole will come up
with extreme force and could cause injury.
4 -
To adjust the height of the Batter Up loosen the knob on the adjust-
ment collar attached to the center pole.Then slide the adjustment
collar on the B - Center Pole, into the position you desire. Figure 5.
Tighten the knob securely after selecting the proper height.
Then allow the clamp holder to rest on top of adjustment collar.
As seen in Figure 5.
5 -
Figure 4
Assembly Instructions Cont.
Figure 5

Next wrap two Part Gs (Tension Rubber Bands) around Part H. Begin by pulling
one end of the Rubber Band through the loop of the
opposite end as shown in Figure 7.
Note: Make sure to use two Rubber Bands for the necessary spring back strength.
(The Batter Up comes with ten tension rubber bands,from time to time it may be
necessary to replace worn or broken rubber bands.Just follow the instructions on this
page to replace them as needed.)
6 -
After wrapping the Rubber Band around the pole, pull the free end until you can
hook the Rubber Band over the“S”Hook as shown in Figure 8.
7-
After attaching the Rubber Bands to the“S” Hook make sure the rubber bands
around the pole are pulled tight to keep them from sliding around the pole when hit.
If the rubber bands still slide around the pole you may want to use black tape to
secure the Rubber Bands to the Pole by taping over the Rubber Bands and Pole
where the two join.
This will keep the Rubber Bands in place when the bands are not tight around the
pole. See Figure 9.
8-
Figure 6
Assembly Instructions Cont.
Figure 7
Figure 8

With the two knobs and lock washers removed, slide the “U”shaped
side of the clamp off of the fixed side of the clamp. See Figure 10.
9 -
After removing the clamp place the handle of the Perfect Swing batting stick
into the clamp and replace the removed“U” shaped side of the clamp.
Note: Make sure the handle of the Perfect Swing is centered so that the
clamp will fit perfectly around the grip and hold securely.
Important: Make sure to position the Perfect Swing so that the safety strap
attached to the ball end of the Perfect Swing is on the back side of the ball
and neck, facing away from the hitter.
10 -
Figure 9
Assembly Instructions Cont.
Figure 10
With the Tension Rubber Bands (Part G) attached, remove both knobs and
lock washers from the“U”shaped clamp on Part B. See Figure 10.

The Batter Up can be used on hard surfaces, grass and dirt. Simply
remove the Rubber Stopper in the Base and fill the Batter Up with
water, sand or cement.Water or sand will be sufficient for most children
under 12 years of age. Cement may be necessary for older children and
adults.
This will help to keep the Batter Up stationary swing after swing.
After filling the base place the Batter Up Decal on the Base.
Note: For additional support drive the three supplied
Ground Stakes (Part I) into the ground next to the base.This
will keep the Batter Up from moving out of the desire location.
12 -
Figure 12
Rubber Stopper
Ground Stakes
Ground Stake
Assembly Instructions Cont.
®
Once the clamp is in position with the Perfect Swing batting stick inserted,
replace the lock washers and the knobs and tighten until the batting stick is
securely in place. See Figure 11.
Note: You may wrap the wrist strap of the Perfect Swing through the eye
of the swivel and around the clamp knobs. Keeping the wrist strap away
from the swivel function.
11 -
Figure 11

The batter should take a position where the point of contact is
on the ball of the Perfect Swing batting stick. Avoid contact
to the shaft of the batting stick as this may cause damage
to the device.
•
Multiple Tension Rubber Bands are provided
with the Batter Up. After repeated use the
Rubber Bands may become weak or break.
Simply replace the worn bands when needed.
Do not use the Batter Up without the necessary
Rubber Bands.This may cause undue stress on
the Base and Pole.
•
The Batter Up is basically two training
devices in one.You can remove the Perfect
Swing batting stick and use it as a two
person training stick.
Hold the Perfect Swing batting stick with
both hands using the strap to secured the
batting stick to the wrist. Position the ball in
the desired location for the batter to hit.The
holder should not fight the momentum of
the contact but rather go with it.
Follow all instructions and warnings
when using these products.
•
Instructions For Use
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]
®