Heatilator ECO-ADV-PS35 User manual

www.heatilatorecochoice.com
Consumer Care 1-877-427-3316 - Prior to calling, please have the model and serial number of the unit you are calling
about. This information can be found at the rear of the unit.
Fire Risk.
WARNING
Tested and approved for wood pellets.
Burning of any other type of fuel will void
your warranty.
WARNING
Hot glass will cause burns.
• Donottouchglassuntilitiscooled
• NEVERallowchildrentotouchglass
• Keepchildrenaway
• CAREFULLYSUPERVISEchildreninsameroomas
replace.
• Alertchildrenandadultstohazardsofhigh
temperatures.
High temperatures may ignite clothing or other
ammable materials.
• Keepclothing,furniture,draperiesandotherammable
materials away.
HOT SURFACES!
Glass and other surfaces are
hotduringoperationAND
cool down.
Owner’s Manual
InstallationandOperation
Models:
ECO-ADV-PS35
ECO-ADV-PS50
ECO-CAB50
Pellet Burning Stove
7058-142F•June23,2011 1
Check building codes prior to installation.
• InstallationMUSTcomplywithlocal,regional,stateandnational
codes and regulations.
• Consultlocalbuilding,reofcialsorauthoritieshavingjurisdic-
tionaboutrestrictions,installationinspection,andpermits.
CAUTION
DO NOT DISCARD THIS MANUAL
CAUTION
• Importantoperatingand
maintenance instruc-
tions included.
• Leavethismanualwith
partyresponsibleforuse
and operation.
• Read,understandand
follow these instruc-
tionsforsafeinstalla-
tion and operation.
DO NOT
DISCARD
ECO-ADV-PS35 ECO-ADV-PS50 ECO-CAB50
WARNING
If the information in these instruc-
tions is not followed exactly, a
re may result causing property
damage, personal injury, or death.
• Donotstoreorusegasolineorotheram-
mablevaporsandliquidsinthevicinityof
thisoranyotherappliance.
• Donotoverre-Ifheaterorchimney
connectorglows,youareoverring.Over
ringwillvoidyourwarranty.
• Complywithallminimumclearancesto
combustiblesasspecied.Failureto
complymaycausehousere.

NOTE: Consult
insurance carrier,
local building
inspector, re
ofcials or authorities
having jurisdiction
over restrictions,
installation inspection
and permits.
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
Congratulations!
Congratulations on selecting a Heatilator pellet burning
appliance.Thepelletburningapplianceyouhaveselected
isdesignedtoprovidetheutmostinsafety,reliabilityand
efciency.
Astheownerofanewpelletburningappliance,you’llwant
toreadandcarefullyfollowalloftheinstructionscontained
inthisowner’smanual.Payspecialattentiontoallcautions
andwarnings.
Thisowner’smanualshouldberetainedforfuturerefer-
ence.Wesuggestyoukeepitwithyourotherimportant
documentsandproductmanuals.
Yournewpelletburningappliancewillgiveyouyearsof
durableuseandtrouble-freeenjoyment.Welcometothe
Heatilatorfamilyofpelletburningproducts!
Manufactured
date
Serial Number
Model Name
SAMPLE: CLEARANCE
TO COMBUSTIBLES
LABEL
LOCATION: Back of Stove
Listed Solid Fuel Room Heater/Pellet Type. Also suitable for Mobile Home Installation.
This appliance has been tested and listed for use in Manufactured Homes in
accordance with OAR 814-23-9000 through 814-23-909.
PREVENT HOUSE FIRES
Install and use only in accordance with manufacturer's installation and operating instructions.
Contact local building or fire officials about restrictions and inspection in our area.
WARNING - FOR MOBILE HOMES: Do not install appliance in a sleeping room. An
outside combustion air inlet must be provided. The structural integrity of the mobile home
floor, ceiling and walls must be maintained.
Refer to manufacturer's instructions and local codes for precautions required for passing
chimney through a combustible wall or ceiling. Inspect and clean vent system frequently
in accordance with manufacturer's instructions.
DO NOT CONNECT THIS UNIT TO A CHIMNEY SERVING ANOTHER APPLIANCE.
Use a 3" or 4" diameter type "L" or "PL" venting system.
Tested to: ASTM E1509-04, ULC S627-00, ULC/ORD-C1482-M1990 Room Heating
Pellet BurningType, (UM) 84-HUD FOR USE
ONLY WITH PELLETIZED WOOD. Do not
use any other type of fuel. Intertek-Test Laboratories has determined that this appliance
complies with Canadian Standards Association (CSA) B415.1 and Title 40 of the U.S.
Code of Federal Regulations, Part 60, SubPart AAA.
Input Rating: 50,000 Btu's/hr. Electrical Rating:115 VAC, 60 Hz, Start 5.1 Amps, Run 3.0 AMPS.
Route power cord away from unit. Do not route cord under or in front of appliance. Do
not obstruct the space beneath the heater.
DANGER:
Risk of electrical shock. Disconnect power supply before servicing. Replace
glass only with 5mm ceramic available from your dealer. To start, set thermostat above
room temperature, the stove will light automatically. To shutdown, set thermostat to below
room temperature. For further instruction refer to owner's manual.
Keep viewing and ash removal doors tightly closed during operation.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS / ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:
U.S. ENVIRONMENTAL PROTECTION AGENCY
This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].
2011 2012 2013 JAN FEB MAR APR MAY JUNE JULY AUG SEPT OCT NOV DEC
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
PRÉVENTION DES FEUX DE MAISON
I nstallez et utilisez en accord avec les instructions d'installation et d'opération du fabricant. Contactez le
bureau de la construction ou le bureau des incendies au sujet des restrictions et des inspections d'installation
dans votre voisinage. Ne pas obstruez l'espace en dessous de l'appareil.
A VIS - Pour Les Maisons Mobiles: Ne pas installer dans une chambre à coucher. Un tuyau extérieur de
combustion d'air doit être installé et ne doit pas être obstrué lorsque l'appareil est en usage. La structure
intégrale du plancher, du plafond et des murs de la maison mobile doit être maintenue intacte.
Référez vous aux instructions du fabricant et des codes locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles, et les compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Ne pas connecter cet appareil à une cheminée servant un
autre appareil. Utilisez systèm de ventilation "L" ou "P" diamètre 76mm ou 102mm
Testé à: ASTM E1509-04,ULC S627-00, ULC/ORD-C1482-M1990 Room Heating. Pellet Burning
Type, (UM) 84-HUD POUR USAGE AVEC LES BOULETTES DE BOIS. N’utiliser aucun autre
genre de combustible.
Intertek Test Laboratories a déterminé que cet appareil se conforme
avec la norme de l’Association Canadienne de normalisation (CSA) B415.1 ainsi que le Titre 40
du Code Fédéral de Régulations des États-Unis, partie 60, sous-partie AAA.
Puissance de Rendement: 50,000Btu's/hr. Puissance Électrique: 115 VAC, 60 Hz, Début 5.1 Amps, Courir 3.0
Amps,
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de
l'appareil. Ne pas bloquer l’espace au dessous de l’appareil.
DANGER:Il y a risque de décharge électrique. Déconnectez le fil électrique de la prise de contact avant le
service.
Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseur.
Pour allumer, monter la température du thermostat au dessus de la température de la pièce, le poêle
s'allumera automatiquement. Pour éteindre, descendre la température du thermostat en dessous de la
température de la pièce. Pour des instructions supplémentaires, référez vous au manuel du propriétaire.
Gardez la porte d'ouverture et la porte des cendres fermées hermétiquement durant l'opération.
Appareil de chauffage de combustible solide/de type de boulettes.
Accepté dans l'installation dans les maisons mobiles. Cet appareil a été testé et enregistré pour
l'usage dans les Maisons Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.
1445 Highway North
Colville, WA 99114
Manufactured by:Fabriqué par:
SERIAL NO. / NUMÉRO DU
CAB50 Pellet Stove
A Back Wall / Mur Arrière 2 in [51mm]
B Side Wall / Mur De Côté 14 in [356mm]
CORNER INSTALLATION / NSTALLATION DU COIN :
C Side Wall / Mur De Côté 2 in [51mm]
VERTICAL 3 in. - 3 in. ADAPTER KIT (PART 811-0860) INSTALLATION:
UN ASSEMBLAGE POUR ADAPTEUR 3- 3 in (76-76mm) (PIÈCE 811-0860) POUR INSTALLATION VERTICALE:
D Pipe to Back Wall / Un Tuyau Mur Arrière 1 in [25mm]
E Side Wall / Mur De Côté 14 in [356mm]
F Back Wall / Mur Arrière 6.25 in [159mm]
CORNER INSTALLATION WITH VERTICAL ADAPTER KIT:
INSTALLATION DU COIN AVEC UN ASSEMBLAGE D'ADAPTEUR VERTICAL :
G Side Wall / Mur De Côté 2 in [51mm]
ALCOVE INSTALLATION /
INSTALLATION DE L' ALCÔVE :
Min. Alcove Height: / Une hauteur minimum de l'alcôve 56.75 in [ 1441mm]
Min. Alcove Side Wall: / Une hauteur minimum m ur de côté de l'alcôve 14 in [356mm]
Min. Alcove Width /
Une épaisseur minimum m ur de côté de l'alcôve 53 in [1346mm]
Max. Alcove Depth: /
La profondeur maximum de l'alcôve 48 in [1219mm]
Max. Mantle Depth: /
Profondeur maximum de la manteau de cheminée 36 in [914mm]
Top of Unit to Combustibles: / Vue du haut des matériaux combustibles 21 in [533mm]
Note 1: In residential installations, when using Parts TPVNT-5, (3" - 3" Top Vent Adapter)
and 812-3570 (3" - 6" Offset Adapter), 24 gauge 6" single wall flue connector may be used.
Note 1: Dans les installations résidentielles, lorsque les pièces TPVNT-5, (dessus de
l'adapteur de ventilation 3" - 3") et 812-3570 (le ressaut de l'adapteur 3" - 6"), un tuyau
connecteur de 6" pour mur simple de calibre 24 peut être utilisé.
Note 2: In manufactured home installation, when using Part TPVNT-5, (3" - 3" Top Vent
Adapter) and 812-3570 (3' - 6" Offset Adapter), use listed double wall flue connector. An
Outside Air Kit, must be used with manufactured home installation.
Note 2: Pour l'installation dans les maisons préfabriquées, lorsque les pièces TPVNT-5,
(dessus de l'adapteur de ventilation 3" - 3") et 812-3570 (le ressaut de l'adapteur 3" - 6"),
utilisez un tuyau connecteur enregistré pour mur double. Un assemblage d'air extérieur, doit
être utilisé pour l'installation dans les maisons préfabriquées.
www.heatilatorecochoice.com
007025
FLOOR PROTECTION / PROTECTION DU SOL
* Non-combustible floor protection must extend 2 inches
[51mm] beneath the flue pipe when installed with horizontal
venting or under the Top Vent Adapter with vertical installation.
RECOMMENDED IN USA; REQUIRED IN CANADA.
*Un protecteur incombustible de plancher doit s'étendre 2 inches [51mm]
sous le conduit de cheminée pour une installation de ventilation horizontale
ou sous un adapteur de ventilation de dessus pour une installation verticale.
ÉTATS-UNIS - RECOMMANDÉ; CANADA - REQUIRENT.
7074-143
W/N 20514
Floor protector must be non-combustible material, extending
beneath heater and to the front/sides/rear as indicated.
Measure front distance (I) from the surface of the glass door.
Le poêle doit être placé sur une assise non combustible s’étendant tout
autour de lui, comme les schémas l’indiquent. Mesurez la distance du
devant (I) de la surface de la porte vitrée.
CAUTION : HOT WHILE IN OPERATION DO NOT TOUCH, KEEP
CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE
SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.
ATTENTION: CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER.
GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE
DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES
BRÛLURES À LA PEAU. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.
Made in U.S.A. of US and imported parts. / Fabriqué aux États-Unis-d’Amérique par des pièces d’origine américaine et pièces importées.
A
B
C
C
D
E
FC
C
USA
G = 2 in
H* = 2 in
I = 6 in
CANADA
G = 203 mm
H* = 51 mm
I = 152 mm
G
H
I
G
ETL4001508
SAMPLE

Safety Alert Key:
• DANGER! Indicatesahazardoussituationwhich,ifnotavoidedwillresultindeathorseriousinjury.
• WARNING!Indicatesahazardoussituationwhich,ifnotavoidedcouldresultindeathorseriousinjury.
• CAUTION! Indicatesahazardoussituationwhich,ifnotavoided,couldresultinminorormoderateinjury.
• NOTICE:Indicatespracticeswhichmaycausedamagetothereplaceortoproperty.
Congratulations ...............................................................2
SampleofSafety/SerialNumberLabel ...........................2
SafetyAlertKey...............................................................3
Warranty..........................................................................4-5
Section 1: Listing and Code Approvals
 A. ApplianceCertications.....................................6
 B. MobileHomeApproved.....................................6
 C. GlassSpecications..........................................6
D. Electrical Rating ................................................6
 E. BTU&EfciencySpecications........................6
User’s Guide
Section 2: Operating Instructions
A. YourPelletAppliance,GeneralOperatingParts..7
 B. FireSafety.........................................................8
 C. Combustible/Non-CombustibleMaterial............8
 D. FuelMaterial&FuelStorage ............................8
 E. GeneralOperationInformation..........................9
 F. BeforeYourFirstFire........................................9
 G. HopperLidLatchandHopperSwitch ...............9
 H. StartingYourFirstFire......................................10
 I. FireCharacteristics ...........................................10
 J. FeedRateAdjustment ......................................10
 K. IgnitionCycles...................................................11
 L. ClearSpace ......................................................11
Section 3: Maintaining & Servicing Appliance
 A. ProperShutdownProcedures...........................12
 B. QuickReferenceMaintenanceChart................12
 C. GeneralMaintenance&Cleaning .....................12-15
 D. HighAshFuelContentMaintenance ................16
E. FrequentlyAskedQuestions.............................17
Section 4: Replacement Parts
 A. ConvectionBlower ............................................18
 B. ExhaustBlower ................................................19
 C. SnapDisc#1,#2,&#3tReplacement ..............20
 D. IgniterReplacement..........................................21
 E. BafeRemoval&Replace ................................21
 F. GlassAssembly ................................................22
Installer’s Guide
Section 5: Getting Started
 A. Design,Installation&Location
Considerations ..................................................23
 B. Draft ..................................................................23
 C. NegativePressure.............................................23-24
Section 5: Getting Started (Cont’d)
 D. ThermostatLocation .........................................24
 E. LocatingyourAppliance&Chimney .................24
 F. Tools&SuppliesNeeded..................................25
 F. InspectApplianceandComponents .................25
Section 6: Dimensions & Clearances
 A. ApplianceDimensions.......................................26-28
 B. ClearancestoCombustibles ...........................29
C. Alcove ...............................................................30
 D. HearthPadRequirements.................................31
Section 7: Vent Information
 A. Chimney&ExhaustConnection .......................32
 B. VentingTerminationRequirements...................32
 C. PelletVentingCharts ........................................33
Section 8: Venting Systems
 A. Vertical-Interior................................................34
 B. ThroughtheWall&Vertical-Exterior.................34
 C. VerticalintoClassAChimney..........................34
 D. Masonry ..........................................................35
 E. AlternateMasonry.............................................35
 F. ThroughtheWall...............................................36
Section 9: Mobile Home Installation..................37
Section 10: Appliance Set-Up
 A. OutsideAirKit ...................................................38
 B. TopVentAdapter..............................................39
C. Rear Vent Adapter ............................................39
 D. ThermostatInstallation......................................40
Section 13: Troubleshooting...............................41-43
Section 14: Reference Materials
A. ComponentFunctions.......................................44-45
 B. ComponentLocations .......................................46
C. ExplodedDrawing-PS35.................................47
 D. ServiceParts&Accessories-PS35.................48-50
 E. ExplodedDrawing-PS50.................................51
 F. ServiceParts&Accessories-PS50.................52-53
 G. ServiceParts&Accessories-PS50/CAB50.....54
 H. ExplodedDrawing-CAB50 ..............................55
 I. ServiceParts&Accessories-CAB50 ..............56-57
 J. Service&MaintenanceLog ..............................58
 K. Homeowner’sNotes..........................................59
 L. ContactInformation...........................................60
TABLE OF CONTENTS

Warranty Period Heatilator ECO-CHOICE
Appliances Components Covered
Parts Labor Pellet EPA Wood
1 year X X All parts and material except as covered by
Conditions, Exclusions, and Limitations listed
3 years X Firepots and burnpots
3 years 1 year X X Castings
5 years 3 years X Manifold tubes
5 years 3 years X X Firebox and heat exchanger
90 days X X All replacement parts beyond warranty period
See conditions, exclusions,and limitations on next page
Page 1 of 2
Hearth & Home Technologies Inc.
HEATILATOR ECO-CHOICE WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (“HHT”), extends the following warranty for ECO-
CHOICE by heatilator wood and pellet hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrantes to the original owner of the HHT appliance at the site of installation, and to any transferree taking own-
ership of the appliance at the site of installation within two years following the date of original purchase, that the HHT
appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if cov-
ered components manufactured by HHT are found to be defective in materials or workmanship during the applicable
warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully
discharge all of its obligations under such warranties by replacing the product itself or refunding the veried purchase
price of the product itself. The maximum amount recoverable under this warranty is limited to the purchaser price of
the product. This warranty is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of rst occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period
for parts and labor for covered components is produced in the following table.
7014-212B 1-10-11
Warranty Policy
Warranty Period Heatilator ECO-CHOICE
Appliances Components Covered
Parts Labor Pellet EPA Wood
1 year X X All parts and material except as covered by
Conditions, Exclusions, and Limitations listed
3 years X Firepots and burnpots
3 years 1 year X X Castings
5 years 3 years X Manifold tubes
5 years 3 years X X Firebox and heat exchanger
90 days X X All replacement parts beyond warranty period
See conditions, exclusions,and limitations on next page
Page 1 of 2
Hearth & Home Technologies Inc.
HEATILATOR ECO-CHOICE WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (“HHT”), extends the following warranty for ECO-
CHOICE by heatilator wood and pellet hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrantes to the original owner of the HHT appliance at the site of installation, and to any transferree taking own-
ership of the appliance at the site of installation within two years following the date of original purchase, that the HHT
appliance will be free from defects in materials and workmanship at the time of manufacture. After installation, if cov-
ered components manufactured by HHT are found to be defective in materials or workmanship during the applicable
warranty period, HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully
discharge all of its obligations under such warranties by replacing the product itself or refunding the veried purchase
price of the product itself. The maximum amount recoverable under this warranty is limited to the purchaser price of
the product. This warranty is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of rst occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period
for parts and labor for covered components is produced in the following table.
7014-212B 1-10-11

WARRANTY COVERAGE:
• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on th HHT branded websites.
• This warranty is only valid while the HHT appliance remains at the site of original installation.
• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface nishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface nishes may occur. This is not a aw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by ngerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacment of parts that are subject to normal wear and tear during the warranty period. These parts include:
paint, wood, pellet and coal gaskets; rebricks; grates; ame guides; light bulbs; batteries and the discoloration of
glass.
• Minor expansion, contraction, or movement of certain parts causing noise. These conditions are normal and com-
plaints related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identication label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper operation,
abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/incorrectly
performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting caused by tightly
sealed constructions, insufcient make-up air supply, or handling devices such as exhaust fans or forced air furnaces
or other such causes; (6) use of fuels other than those specied in the operating instructions; (7) installation or use of
components not supplied with the appliance or any other components not expressly authorized and approved by HHT;
(8) modication of the appliance not expressly authorized and approved by HHT in writing; and/or (9) interruptions or
uctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing replace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliances’ capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and conguration, environmental conditions, insulation and air tightness of
the structure.
This warranty is void if:
• The appliance has been over-red or operated in atmospheres contaminated by chlorine, uorine, or other damaging
chemicals. Overring can be identied by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel nishes.
• The appliance is subjected to prolonged periods of dampness or condensation.
• There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to improper chimney or venting installation.
WARRANTY EXCLUSIONS:
• The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specied above. In no
event will HHT be liable for any incidiental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specice rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE EX-
PRESSED WARRANTY SPECIFIED ABOVE.
Page 2 of 2
7014-212B 1-10-11

A. Appliance Certication
C. Glass Specications
E. BTU & Efciency Specications
This appliance is equipped with 5mm ceramic glass.
Replaceglassonlywith5mmceramicglass.Pleasecontact
yourdealerforreplacementglass.
B. Mobile Home Approved
NOTE: Thisinstallationmustconformwithlocalcodes.
Intheabsenceoflocalcodesyoumustcomplywiththe
ASTM E1509-04, ULC S627-00, ULC/ORD-C-1482-
M1990, (UM) 84-HUD,
*BTUinputwillvary,dependingonthebrandoffuel
youuseinyourstove.Consultyourdealerforbest
results.
NOTE: Hearth&HomeTechnologies,manufacturerof
thisappliance,reservestherighttoalteritsproducts,
theirspecicationsand/orpricewithoutnotice.
MODEL: PS35
Particulate Emissions
Rating: 0.9grams/hr
*BTU Input: 13,000-35,000/hr
Heating Capacity: 750to1450sq.ft.depending
onclimatezone
Hopper Capacity: (Approx) 45 lbs
Fuel: WoodPellets
Shipping Weight: 210 lbs
Models: ECO-ADV-PS35,ECO-ADV-PS50
andECO-CAB50
Laboratory: Intertek
Report No. 3198406
Type: SolidFuelRoomHeater/Pellet
FuelBurningType
Standard: ASTME1509-04andULC
S627-00,ULC/ORD-C1482-
M1990RoomHeaterPelletFuel
Burningtypeand(UM)84-HUD,
MobileHomeApproved.
1Listing and Code Approvals
TheECO-CHOICEbyHeatilatorpelletstove isexemptfrom
EnvironmentalProtectionAgencycerticationunder40CFR
60.531bydenition[WoodHeater(A)“AirtoFuelRatio].
 • Thisapplianceisapprovedformobilehomeinstalla-
tionswhennotinstalledinasleepingroomandwhen
anoutsidecombustionairinletisprovided.
 • Thestructuralintegrityofthemobilehomeoor,ceil-
ing,andwallsmustbemaintained.
 • Theappliancemustbeproperlygroundedtotheframe
ofthemobilehomewith#8coppergroundwire,and
useonlylisteddouble-wallconnectorpipe.
 • OutsideAirKit,part811-0872orOAK-3mustbein-
stalledinamobilehomeinstallation.
HeatilatorisaregisteredtrademarkofHearth&Home
Technologies.
WARNING! Risk of Fire! Hearth&HomeTechnologiesdis-
claimsanyresponsibilityfor,andthewarrantyandagency
listingwillbevoidedbythebelowactions.
DO NOT:
 • Installoroperatedamagedappliance
 • Modifyappliance
 • InstallotherthanasinstructedbyHearth&Home
Technologies
 • Operatetheappliancewithoutfullyassemblingall
components
 • Overre
 • InstallanycomponentnotapprovedbyHearth&
HomeTechnologies
 • InstallpartsorcomponentsnotListedorapproved
 • Disablesafetyswitches
Improper installation, adjustment, alteration, service or
maintenancecancauseinjuryorpropertydamage.
Forassistanceoradditionalinformation,consultaqualied
installer,serviceagencyoryourdealer.
Note: The appliance is also approved for installation
into a shop.
D. Electrical Rating (On High)
Model PS35: 115VAC,60Hz,Start3.8Amps,Run1.3Amps
Model PS50: 115VAC,60Hz,Start5.1Amps,Run3.0Amps
Model CAB50: 115VAC,60Hz,Start5.1Amps,Run3.0Amps
MODEL: PS50 / CAB50
Particulate Emissions
Rating: 1.5grams/hr
*BTU Input: 15,000-50,000/hr
Heating Capacity: 1225to2200sq.ft.depending
onclimatezone
Hopper Capacity: (Approx)
83 lbs / 120 lbs
Fuel: WoodPellets
Shipping Weight: 240 lbs
/ 266 lbs

2 Operating Instructions
WARNING! DO NOT operate appliance before reading and understanding operat-
ing instructions. Failuretooperateapplianceaccordingtooperatinginstructionscould
causereorinjury.
User Guide
A. Your Pellet Appliance - General Operating Parts
WARNING
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVERallowchildrentotouchglass
• Keepchildrenaway
• CAREFULLYSUPERVISEchildreninsameroomasappliance.
• Alertchildrenandadultstohazardsofhightemperatures.
High temperatures may ignite clothing or other ammable materials.
• Keepclothing,furniture,draperiesandotherammablematerialsaway.
HOT SURFACES!
GlassandothersurfacesarehotduringoperationANDcooldown.
NOTICE:Ifyouexpectthatchildrenmaycomeintocontactwiththisappliance,werecom-
mendabarriersuchasadecorativescreen.Seeyourdealerforsuggestions.
Feed Rate Adjustment Rod
Heat Output Switch
& Reset Button
Hopper Lid Switch
Firepot Cleaning Rod
Ash Drawer
Firepot &
Thermocouple
Drop Tube for
Pellets
Door Handle
Assembly
Door & Glass
Assembly
3 Baffles
Combustion
Air Damper
Figure 7.1 - General Operating Parts
Thermostat
Theillustrationisintendedtoshowanoverviewoftheoperatingpartsforyourstove.The
appearanceofyourappliancemayvaryslightly.Forspecicpartnumbersandlocations
foryourmodel,seetheexplodedviewdrawingsinthebackofthemanual.

B. Fire Safety
To provide reasonable re safety, the following should be
givenseriousconsideration:
• Installatleastonesmokedetectoroneachoorofyour
home.
• Locatesmokedetectorawayfromtheheatingappliance
and close to the sleeping areas.
• Followthesmokedetectormanufacturer’splacementand
installationinstructionsandmaintainregularly.
• ConvenientlylocateaClassAreextinguishertocontend
withsmallres.
• Intheeventofahopperre:
 • Evacutethehouseimmediately.
• Notifyredepartment.
C. Combustible/Non-Combustible Materials
• Combustible Material
Material made of or surfaced with wood, compressed
paper, plant bers, plastics, or any material capable
of igniting and burning, whether ame-proofed or not,
plastered or unplastered.
• Non-combustible Material
 Materialwhichwillnotigniteandburn.Suchmaterialsare
thoseconsistingentirelyofsteel,iron,brick,tile,slate,
glassorplasters,oranycombinationthereof.
• Non-combustible Sealant Material
 Sealants which will not ignite and burn: Rutland, Inc.
Fireplace Mortar #63, Rutland 76R, Nuex 304, GE
RTV106orGERTB116(orequivalent).
Clinkers
Mineralsandothernon-combustiblematerialssuchassand
willturnintoahard,glass-likesubstancecalledaclinkerwhen
heatedintherepot.
Treesfromdifferentareaswillvaryinmineralcontent.That
iswhysomefuelsproducemoreclinkersthanothers.
Moisture
Alwaysburndryfuel.Burningfuelwithhighmoisturecontent
takes heat from the fuel and tends to cool the appliance,
robbingheatfromyourhome.Damppelletfuelcanclogthe
feedsystem.
Size
• Pelletsareeither1/4inchor5/16inch(6-8mm)indiameter
• Lengthshouldbenomorethat1-1/2inches(38mm)
• Pellet lengths can vary from lot to lot from the same
manufacturer
• Duetolengthvariations,thefeedratemayneedadjusting
occasionally
Performance
• Higherashcontentrequirestherepotandtheashdrawer
tobeemptiedmorefrequently
• Hardwoodsrequiremoreairtoburnproperly
• Premiumwoodpelletsproducethehighestheatoutput
• Burningpelletslongerthan1-1/2inches(38mm)cancause
an inconsistentfuelfeedrateand/ormissedignitions
D. Fuel Material and Fuel Storage
Pelletfuelqualitycangreatlyuctuate.Werecommendthat
youbuyfuelinmulti-tonlotswheneverpossible.However,
wedorecommendtryingvariousbrandsbeforepurchasing
multi-tonlotstoensureyoursatisfaction.
FuelMaterial
• Madefromsawdustorwoodby-products
• Dependingonthesourcematerialitmayhaveahighor
lowashcontent.
HigherAshContentMaterial
• Hardwoodswithahighmineralcontent
• Fuelthatcontainsbark
• Standardgradepelletsorhighashpellets
LowerAshContentMaterial
• Mostsoftwoods
• Fuelswithlowmineralcontent
• Mostpremiumgradepellets
Storage
• Woodpelletsshouldbeleftintheiroriginalsealedbaguntil
usingtopreventmoistureabsorption
• Do not store any pellet fuel within the clearance
requirements or in an area that would hinder routine
cleaningandmaintenance

F. Before Your First Fire
1. First, make sure your appliance has been properly
installedandthatallsafetyrequirementshavebeenmet.
Payparticularattentiontothereprotection,ventingand
thermostatinstallationinstructions.
2. Double check that the ash drawer and firebox are
empty!
3. Close and latch the door.
NOTICE: The tip of the thermocouple must be in contact
with the inside end of the thermocouple cover or missed
ignitions can occur.
E. General Operating Information
1. Thermostat Calls For Heat
The appliance is like most modern furnaces; when the
thermostatcallsforheat,yourappliancewill automatically
lightanddeliverheat.
Whentheroomisuptotemperatureandthethermostat
issatised,theredcalllightwillgooffandtheappliance
willshutdown.
2. Heat Output Controls
This appliance is equipped with a heat output control
switchthathasthreesettingsorburnrates;low,medium
and high. Figure 9.1.
The appliance will turn on and off as the thermostat
demands.  When the thermostat calls for heat, the
appliancewillstartupattheburnrateforwhichitisset.If
theapplianceissetatoneofthelowersettings,itwillrun
quieterbuttakelongertoheatupanareathanifitwere
set at a higher burn rate.
Regardlessoftheburnrate,whentheareaiswarmenough
tosatisfythethermostat,theappliancewillshutoff.
Figure 9.1
WARNING
FireHazard.
Keepcombustiblematerials,gasoline
andotherammablevaporsandliquids
clearofappliance.
• DoNOTstoreammablematerialsintheappliance’s
vicinity.
• DONOTUSEGASOLINE,LANTERNFUEL,KEROSENE,
CHARCOALLIGHTERFLUIDORSIMILARLIQUIDSTO
STARTOR“FRESHENUP”AFIREINTHISHEATER.
• DONOTBURNGARBAGEORFLAMMABLEFLUIDS
SUCHASGASOLINE,NAPHTHAORENGINEOIL.
• DONOTUSECHEMICALSORFLUIDSTOSTARTTHE
FIRE.
• Keepallsuchliquidswellawayfromtheheaterwhileitisin
use.
• Combustiblematerialsmayignite.
G. Hopper Lid Latch and Hopper Switch
1. Liftupthehopperlidandlockintoopenposition.Now
youcanllthehopperwithfuel.
2. Thehopperswitchisdesignedtoshutdownthefeed
motorwhenthehopperlidisopen.Leavingthelidopen
toolongcancausetheretogoout.Figure 9.2.
3. Toclosethehopperlid,whileholdinglidopenwithone
hand,pushthebottomofthelatchinwardstorelease
fromlockedpositionandthenslowlyclosethehopper
lid. Figure 9.3.
Note: The CAB50 has no hopper lid latch.The hopper
switchislocatedinasimilarlocationandisactivated
byamagnetattachedtotheHopperLid.
Hopper Lid Latch
Hopper Switch
Push Bottom of Latch
Inward to Release
Figure 9.2
Figure 9.3

I. Fire Characteristics
Aproperlyadjustedrewiththeheatoutputcontrolswitchset
on“high”hasashortactiveamepatternthatextendsoutof
therepotapproximately4to8inches(102to203mm).
Iftherehastallameswithblacktailsandseemssomewhat
lazy,thefeedratewillneedtobereduced.Thisisdoneby
slidingthefueladjustmentcontrolroddown,whichwillreduce
thefeed.Figure 10.3.
Ifthereisnot4to8inches(102to203mm)tall,slidethe
fueladjustmentcontrolroduptoincreasethefeed.Amedium
andlowsettingwillgiveashorterame.Theamewillrise
andfallsomewhat.Thisisnormal.
Figure 10.2
Thefeedadjustmentcontrolrodisfactoryset,andshould
beadequateformostfuels.However,iftheflameheightis
toohighortoolow,youwillneedtoadjustthefeedrate.Wait
untiltheappliancehasbeenburningfor15minutesbefore
making your adjustments and a llow 15 minutes for feed
adjustmenttotakeeffect.
J. Feed Rate Adjustment Instructions
1. Loosenthethumbscrew.
2. Pullthefeed adjustmentcontrolrodupto increasethe
feedrateandameheightorpushdowntodecreasethe
feedrateandameheight.
3.Re-tightenthethumbscrew.Anewstovehasabreakin
period.Therecharacteristicsshouldbecheckedagainafter
5bagsofpelletsandadjustmentsmadeifnecessary.
Figure 10.1
H. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance.Ifyouhavetoadjustthefeedrateafteryou
havestartedthere,mostofthepelletsinthehopperwill
needtoberemovedsostartoutwithllingthehopper
approximately1/4fullatthistime.Setthethermostatto
itslowestsettingandplugthepowercordintonearby
outlet.
2. The exhaust blower will stay on for approximately 18
minutes even though the thermostat is not calling for
heat.Thisisnormal.
3. L ocatetheheatoutputcontrolswitchmountedontheback
oftheapplianceintheupperleftcorner.Figure 9.1 on
page 9.
Turn it to the “high” setting by pushing the top of the
control switch in and then adjust the thermostat to its
highest setting.
4. Lookthroughtheholeintheleftlowersidepanelandyou
willsee theredcalllightonthecontrolboxwillbe on.
Figure 10.1.Thisindicatesthethermostatiscallingfor
heat.OntheCAB50thelightcanbeviewedfrombehind
throughtheholenearthebottomleftsideoftherearpanel.
5. Thefuelfeedsystemandtheignitershould now be on.
6. Foryourrstreitwillbenecessarytopress the reset
buttononceapproximately2minutesafterstartupand
again in 5 minutes.  This will ll the feed system and
allow the appliance to begin dropping pellets. Or you
canputahandfulofpelletsintherepottospeedupthe
process. Theappliancewillcontinuetorunaslongas
thethermostatiscallingforheat.
7. Oncetheappliancehasignited,letitburnforapproximately
15minutes,thensetthethermostattothedesiredroom
temperature.Adjusttheheatoutputcontrolswitchtothe
desired setting.
Control Box
Junction Box
Red Call Light
Fuse
Convection
Blower
LOCATED BEHIND LEFT SIDE PANELS
Feed Adjustment Rod located
inside Hopper at Front
Bottom of Hopper
Loosen Thumb Screw
Pull Up to
Increase
Push Down to
Decrease
Figure 10.3
Odorsandvaporsreleasedduringinitialoperation.
• Curingofhightemperaturepaint.
• Openwindowsforaircirculation.
Odorsmaybeirritatingtosensitiveindividuals.
CAUTION

K. Ignition Cycles
1. Atthebeginningofeachignitioncycle,itisnormaltosee
somesmokeintherebox.Thesmokewillstoponce
therestarts.
2. The convection blower will automatically turn on after
yourappliancehasbeenburningforapproximately10
minutes.
Thisblowertransfersheatfromyourapplianceintothe
room,andwillcontinuetorunafterthethermostathas
stoppedcallingforheatuntiltheappliancehascooled
down.
3. Occasionallytheappliancemayrunoutoffuelandshut
itselfdown.Whenthishappens,theredcalllightwillbe
on. See Figure 10.1, page 10.
Torestartit,llthehopperandpresstheresetbutton.
Whenyoupresstheresetbuttontheredcalllightwillgo
out.Releasethebuttonandthelightwillcomebackon.
Continuepushingthebuttononceaminuteuntilpellets
begintofallintotherepot.
Youshouldseeareshortly.Ifnot,followtheinstructions
on page 10,for“StartingYourFirstFire”.
WARNING
Fire Risk
DoNOToperateappliance:
• Withappliancedooropen.
• Firepotooropen.
DoNOTstorefuel:
• Closerthanrequiredclearancestocom-
bustibles to appliance
• Withinspacerequiredforloadingorash
removal.
WARNING! RISK OF FIRE! Keepcombustiblematerials,
gasolineandotherammablevaporsandliquidsclearof
appliance.
• DoNOTstoreammablematerialsintheappliance’s
vicinity.
• DoNOTusegasoline,lantern fuel,kerosene,charcoal
lighteruidorsimilarliquidstostartor“freshenup”are
inthisheater.
Keepallsuchliquidswellawayfromtheheaterwhileitisin
useascombustiblematerialsmayignite.
L. Clear Space
WARNING! RISK OF FIRE! DoNOTplacecombustible
objectsinfrontortothesidesoftheappliance.Hightem-
peraturesmayigniteclothing,furnitureordraperies.
NOTICE: Clearancesmayonlybereducedbymeansap-
provedbytheregulatoryauthorityhavingjurisdiction.
Mantel:   Avoid placing candles and other heat-sensitive
objects on mantel or hearth.  Heat may damage these
objects.

C. General Maintenance
1. Types of Fuel
Dependingonthetypeoffuelyouareburningwilldictatehow
oftenyouhavetocleanyourrepot.
Ifthefuelyouareburninghasahighdirtorashcontent,itmay
benecessarytocleantherepotmorethanonceaday.
Dirtyfuelwillcauseclinkerstoformintherepot.Aclinker
is formed when dirt, ash or a non-burnable substance is
heated to 2000°F (1093°C) and becomes glass-like.  See
“D” page 16 in this section for more details on fuels with
high ash content.
Clinker
Figure 12.1 - Clinker
Shock and Smoke Hazard
• Turndownthermostat,letappliancecompletely
coolandexhaustblowermustbeoff.Nowyou
canunplugappliancebeforeservicing.
• Smokespillageintoroomcanoccurifappliance
isnotcoolbeforeunplugging.
• Riskofshockifappliancenotunpluggedbefore
servicingappliance.
CAUTION
A. Proper Shutdown Procedure
Cleaning or Inspection Frequency Daily Weekly Monthly Yearly
AshDrawer Every5bagsoffuel OR X
AshRemovalfromFirebox Every5bagsoffuelormore
frequentlydependingonash
build-up
OR
X
Blower,Exhaust Morefrequentlydependingon
thefueltype
OR X
Blower,Convection Every25bagsormorefre-
quentlydependingonoperat-
ingenvironment.
OR
X
DoorHandle&GasketInspection Priortoheatingseason OR X
ExhaustPath,DropTubeandBehind
Bafes
Every25bagsormorefre-
quentlydependingonash
build-up
OR
X
Firepot Cleaning Rod Every1bagoffuel OR X
FirepotwithClean-outTool Every5bagsoffuel OR X
Firebox-PrepareforNon-BurnSeason Atendofheatingseason OR X
Glass Whenclearviewofrepot
becomesobscure
OR X
Hopper Every50bagsoffuel OR X
TopVentAdapter Morefrequentlydependingon
ash build-up
OR X
VentingSystem Every3tonsormorefre-
quentlydependingonthefuel
type
OR
X
B. Quick Reference Maintenance Chart
Follow the detailed instructions found in this
section for each step listed as referenced in the
chart below.
NOTICE: Thesearerecommendations.Cleanmorefrequentlyifyouencounterheavybuild-upof
ashattherecommendedintervaloryouseesootcomingfromthevent.Not properly
cleaning your appliance on a regular basis will void your warranty.
3Maintaining & Servicing Your Appliance

2. Cleaning Firepot with Cleaning Rod & Firepot
Clean-Out Tool;
• Frequency:Dailyormoreoftenasneeded
• By:Homeowner
WARNING
• NEVERpullrepotcleaningrodoutwhen
appliance is operating.
• CleaningRodMUSTbecompleletypushedin
beforeoperatingappliance.
•.Hotpelletsmayfallintoashpanandstartare
ormis-startsduetolackofvacuum.
Fire Risk
4. Cleaning Ash Drawer
• Frequency:Weeklyorevery5bagsoffuel
• By:Homeowner
3. Ash Removal from Firebox
• Frequency:Weeklyormorefrequentlydependingon
ash build-up.
• By:Homeowner
Pull out Ash Drawer & Dispose of
Ashes in Non-Combustible Container
Ash Drawer
Figure 13.3
Firepot Cleaning Rod
Figure 13.1
Figure 13.2
OPEN Position. Light color
painted area visible
CLOSED Position
No light color paint is visible
Lift up and push closed
WARNING
• NEVERremoveashdrawerwhileapplianceis
operating.
Burn Risk
 a.Theappliancemustbeincompleteshutdownandcool
andtheexhaustbloweroff. Ifyouarejustcleaningthe
repot,thereisnoneedtounplugtheappliance.
 b.Locatetherepotcleaningrodontherightsideofthe
appliance. Figure 13.1.Whenyoupullthecleaningrod
straightoutitwillslideopentherepotoortoallowthe
ashestobedepositedintheashdrawer.Youwillsee
thelightcolorpaintedareaonthecleaningrodtoletyou
knowtherodisinOPENposition. Figure 13.2.
c.PulltherepotcleaningrodOUTandINacoupleoftimes
tohelpshakedebrisloose.Iftherodishardtopull,it
maybenecessarytouseyourrepotclean-outtoolto
chipawaymaterialthathasbuiltuponthebottomplate
oftherepotandtopushoutanyclinkerswhileinthe
open position.
d.Toclosetherepotoor:slightly raise the cleaning rod
andthenpushitbackintoplace.Ifyouhaveclosedthe
cleaningrodproperly(pushedallthewayin)youwillnot
seeanyofthelightcolorpaintedarea.Figure 13.2.
e. Always have the ash drawer in place before pulling
the repot cleaning rod, otherwise the ashes will fall
downandlltheoutsideairopeningandtheappliance
will produce soot out of the exhaust and will affect
efciency.
 a.There must not be any hot ashes in the rebox during
cleaningsoallowtheappliancetocompletelycool.The
reboxashshouldberemovedeverytimetheexhaustpath
iscleaned.Frequentcleaningoftheashinthereboxwill
helpslowdownthebuild-upofashintheexhaustblower
andventsystem.
 b.Vacuum out the rebox thoroughly on both sides of the
reboxandtheoorandceiling.Theashdrawershouldbe
emptiedeverytimeyoucleantherebox.Rememberto
placetheashanddebrisintoametalornon-combustible
container. See Disposal of Ashes. (Pg 14)
c.Always have the ash drawer in place before pulling the
repotcleaningrod,otherwisetheasheswillfalldownand
lltheoutsideairopeningandtheappliancewillproduce
sootoutoftheexhaustandwillaffectefciency.
 a.Theremustnotbeanyhotashesintheashdrawerwhen
youemptyit,soallowtheappliancetocompletelycool.
 b.Locatetheashdrawerunderneaththerepot.Slidethe
ashdrawerstraightout.Emptyintoanon-combustible
containerandre-installtheashdrawer.See Disposal of
Ashes. (Pg 14)
 b.Alwayshavetheashdrawerinplacebeforepullingthe
repotcleaningrod,otherwisetheasheswillfalldownand
lltheoutsideairopeningandtheappliancewillproduce
sootoutoftheexhaustandwillaffectefciency.

Figure 14.1
NOTE: Hearth & Home Technologies recommends to
use a heavy duty vacuum cleaners specically
designed for solid fuel appliance cleaning.
6. Cleaning the Exhaust Path, Bafes & Drop Tube
• Frequency:Monthlyorevery25bagsormorefre-
quentlydependingonashbuild-up.
• By:Homeowner
 a.Appliancemustbecompletelycool.
 b. Openthedoorandremovethecenterbaferstand
thentherightandleftbafes.SeeBafeRemoval
Instructions on page 21.  Thoroughly vacuum the
exhaust path and drop tube and continue throughout
therestoftherebox.Alsovacuumthefrontand
backofthebafes.
 c. Alsovacuumtheconvectionblowerimpellersoruse
asoftbrushtoremoveanyashbuild-up.
 c. Replacetherightandleftbafesandthenthecenter
bafeandcloseandlatchthedoor.
7. Cleaning the Hopper
• Frequency:Monthlyorafterburning50bagsoffuel
• By:Homeowner
After burning approximately 50 bags of fuel you will
needtocleanthehoppertopreventsawdustbuild-up.
A combination of sawdust and pellets on the bottom
endoftheaugerreducestheamountoffuelsupplyto
therepot.Thiscanresultinnuisanceshutdownsand
mis-starts.
 a. The appliance must be in complete shutdown.
Allowtheappliancetocompletelyrunoutofpellets
andcooldown.
 b. Emptythehopperofanyremainingpellets.
 c. Vacuumthehopperandfeedtube.
8. Soot and Fly Ash: Formation & Need for Removal
in Exhaust Venting System.
• Frequency:Yearlyormorefrequentlydependingon
ash build-up.
• By:QualiedServiceTechnician/Homeowner
Besuretheapplianceisallowedtocool,hasbeenunplugged
andtheexhaustblowerisoff.
Theproductsofcombustionwillcontainsmallparticlesofy
ash.Theyashwillcollectintheexhaustventingsystem
andrestricttheowoftheuegases.
Atstart-upifthereisincompletecombustion,orifthereisa
shutdownorincorrectoperationoftheapplianceitwilllead
tosomesootformation.Thiswillcollectintheexhaustvent-
ingsystem.
Theventing(chimney)systemmayneedtobecleanedat
leastonceayearormoreoftendependinguponthequal-
ityofyourfuelorifthereareanyhorizontalpipesections.
Ashwillbuildupmorequicklyinthehorizontalsectionsand
elbows.
Baffles Removed
Exhaust Path and
Blower Impellers
Drop Tube
DisposalofAshes
WARNING
• Ashes should be placed in metal container
withtightttinglid.
• Ashesshouldberetainedinclosedcontainer
untilallcindershavethoroughlycooled.
5. Disposal of Ashes
• Frequency: As needed
• By:Homeowner
Ashes should be placed in a metal container with a
tight-ttinglid.Theclosed containerofashesshould
beplacedonanon-combustibleoororontheground,
wellawayfromallcombustiblematerials,pendingnal
disposal.
Iftheashesaredisposedofbyburialinsoilorotherwise
locally dispersed, they should be retained in the
closedcontaineruntilallcindershavebeenthoroughly
cooled.
9. Door Handle Inspection
• Frequency:Monthlyorpriortoheatingseason
• By:Homeowner
The gasketing between the glass and rebox should be
inspected periodically to make sure there is a good seal.
Checkdoorhandleforsmoothcamoperation.
Locknut
Door Cross Section
(example)
Latch Cam
Spacing
Washer
Square Key
Door Handle
Spring
Handle
Figure 14.2

10. Cleaning the Glass
• Frequency:Whenclearviewoftherepotbecomes
obscure
• By:Homeowner
 a.Appliance mustbecompletelycoolbeforecleaning
glass.
 b. Vacuumyashfromglassanddoorrope.
 c.Useadamppapertoweloranynon-abrasiveglass
cleaner.Wipeoffwithdrytowel.
Handleglassassemblywithcare.
When cleaning glass:
• Avoidstriking,scratchingor
slammingglass.
• DoNOTcleanglasswhenhot.
CAUTION
• DoNOTuseabrasivecleaners.
• Refertomaintenanceinstructions.
11. Cleaning Exhaust Blower - Requires No
Lubrication
• Frequency:Yearlyormorefrequentlydependingon
ash build-up
• By:HomeownerorQualiedServiceTechnician
12. Cleaning Convection Blower - Requires No
Lubrication
• Frequency:Yearlyormorefrequentlydependingon
Dust/Dirtbuild-up
• By:HomeownerorQualiedServiceTechnician
Figure 15.1
a. Theappliancemustbeincompleteshutdownand
theexhaustblowershouldbeoff.Allowtheappli-
ancetocompletelycooldown.
b. Opentheclean-outcover.Figure 15.1.
c. Sweeporvacuumoutanyashbuild-up.
14. Preparing Firebox for Non-Burn Season
• Frequency:Yearly
• By:Homeowner
 a.Besuretheapplianceisallowedtocool,hasbeen
unpluggedandtheexhaustblowerisoff.
b. Removeallashfromthereboxandvacuumthorough-
ly.
 c. Paintallexposedsteel,includingcast-iron.
• Purchasepaintfromyourlocaldealer.
• Mustuseahigh-temperaturepaintmadespeci-
callyforheatingappliances.
Clean-Out Cover
13. Cleaning the Top Vent Adapter
• Frequency:Yearlyormorefrequentlydependingon
ash build-up
• By:Homeowner
Handleglasswithcare.
• Inspectthegaskettoensureitis
undamaged.
• DoNOTstrike,slamorscratchglass.
• DoNOToperateappliancewithglass
assemblyremoved.
WARNING
• DoNOToperatewithglasscracked,brokenor
scratched.
 a.Besurethe appliance isallowed to cool, has been
unpluggedandtheexhaustblowerisoff.
 b.Follow the directions for cleaning the exhaust path
foundonpage 14.
 c.Ifunabletothoroughlycleantheblowerthroughthis
access,thenfollowthedirectionsonpage 19fordirect
accesstotheexhaustblower.
 d.Vacuumtheblower’simpellers.Usecarenottobend
ordamagetheblowerns.
 a.Besuretheapplianceisallowedtocoolandhasbeen
unplugged.
 b.Followthedirectionsonpage 18fordirectaccessto
theconvectionblower.
 c.Sweep or vacuum out any build-up. Use a brush or
compressedairtoloosendirtifneeded.
NOTE: Hearth & Home Technologies recommends to
use a heavy duty vacuum cleaners specically
designed for solid fuel appliance cleaning.

D. High Ash Fuel Content Maintenance
• Frequency: As needed
• By:Homeowner
Figure 16.3
Figure 16.1
Figure 16.2
Fire Risk.
WARNING
• High ash fuels, or lack of maintenance, can
cause the firepot to overfill. Follow proper
shutdown procedure if ash buildup exceeds
half way point in firepot.
• Failure to do so could result in smoking,
sooting and possible hopper fires.
Poorqualitypelletfuel,orlackofmaintenance,cancreate
conditionsthatmaketherepotllquicklywithashesand
clinkers.
Thisconditionmakestheappliancesusceptibletooverlling
therepotwithpelletswhichmayresultinsmoking,sooting
andpossiblehopperres.Figure 16.1showsanexample
wheretherepotoverlls,pelletsbackupintothefeedtube
andashhasaccumulatedintherebox.
Aninefcientandnon-economicalmethodofburningoffuel
causedbypoorqualitypelletfuelisshownin Figure 16.2.
The correct ame size when good quality, premium pellet
fuelisburnedisshowninFigure 16.3.
If the ash buildup exceeds the half way point in the repot
IMMEDIATE ATTENTION AND CLEANING IS REQUIRED.
Odorsandvaporsreleasedduringinitialoperation.
• Curingofhightemperaturepaint.
• Openwindowsforaircirculation.
Odorsmaybeirritatingtosensitiveindividuals.
CAUTION
Correct Flame Height
Yellow/White in Color
Incorrect Flame Height
Tall, Lazy Flame
Orange in Color
Pellets Back-up in Feed Tube
Ash build-up in Firebox
Firepot Overfills

E. Frequently Asked Questions
What causes my glass to become dirty?
If the glass has white ash build up it is normal and the glass
should be cleaned. If it is a black soot build up airow thru
the unit may be restricted. The most often cause is overdue
maintenance and cleaning. See “Maintaining and Servicing
Appliance” in the owner’s manual.
How can I get more heat out of the appliance?
The most often cause of diminished heat output is overdue
maintenance and cleaning . See “Maintaining and Servicing
Appliance” in the owner’s manual. If this still does not help,
verify the correct settings for maximum heat output. See
“Feed Rate Adjustment” under “Operating Instructions” in
the owner’s manual.
What should I do if I smell smoke or there is ash/soot
coming from the appliance?
While there will always be some smoke smell from wood
burning appliances (including pellet) you should investigate
all venting to make sure it is sealed properly. Most venting
requires silicone to seal the seams. In addition most homes
are built very tight today and with exhaust systems can create
negative pressure in the home. See “Negative Pressure”
under “Getting Started” in the owner’s manual if you have
checked the venting but still have smoke coming from the
appliance. For ash or soot check the above and the exhaust
blower housing and seals.
Why would my appliance run ne last winter but not
start this fall?
It is possible that the stove was not properly prepared for
the Non-burn season. See “Trouble shooting” in the owner’s
manual.
Why would the metal on the inside of the appliance begin
to ake?
There are some pellet mills that get their raw materials from
lumber mills that purchase logs that are transported in sea
water. These pellets can have a higher salt content and cause
the metals in the unit to corrode prematurely and deteriorate.
If you are seeing any components inside the rebox deterio-
rate it is recommended to change pellet brands immediately.
Why does only the exhaust blower run when I unplug and
plug back in my appliance?
This is a Safety feature to prevent the unit from operating in
an unsafe condition. Allow the unit to run and it will return to
normal operation.
Is there a place to lubricate the blowers to quiet them
down?
The most often cause of noisy blowers is from the impel-
lers becoming dirty over time. See “General Maintenance &
Cleaning” under “Maintaining & Servicing Appliance” in the
owner’s manual. No form of lubrication should ever need
applied to the blowers.
Why are different components cycling on and off in my
appliance at random?
The selector switch on control box may be on the wrong set-
ting. Refer to the Reference Materials section of our owner’s
manual for details.
What is the metal object with the bend in it for that came
inside the plastic bag?
It is a clean-out tool used to help clean the repot and
remove any jams in the rare event they occur in the feed
tube.
Why is there a black residue building up on the outside of
my home?
Wind can cause this to happen. If the appliance is operating
correctly very little soot should ever exit the termination cap.
Also check to be sure the venting is installed per the owner’s
manual and local codes.
Do I need an outside air kit?
Outside air is required for mobile home installs and in some
jurisdictions. Refer to “Listing & Code Approvals”,“ Mobile
Home Installation” and “ Appliance Set-up” owner’s manual.
Also refer to local building codes.
I am seeing sparks coming out of my pipe (termination
cap) outside is this safe?
This is normal. As long as clearances to combustibles were
followed this is safe.
My unit sounds like a freight train at times what can be
done to eliminate this?
This is referred to as Rumbling. Maintenance may be needed
see “Maintaining and Servicing appliance” in the owner’s
manual. Decrease fuel ow see “Feed rate adjustment”
under Operating Instructions”.
Why does my unit run ne on high, but shuts down on
low and medium?
Maintenance may be needed see “Maintaining and Servicing
Appliance” See also “Trouble Shooting”.
Can I use another brand of wall thermostat or remote
system?
Yes, any remote/wall thermostat system that does not require
power from the appliance should work.
I have no power to anything. Does this unit have a cir-
cuit breaker or fuse or a reset button?
This unit has one serviceable fuse in the junction box and a
reset button for the thermostat circuit.
Can I burn corn in my unit?
Corn is not an approved fuel for the ECO units.
I’m thinking about going green (solar power) and need to
know what the power consumption is on my Unit.
PS50 115 VAC, 60 Hz, Start 5.1 Amps, Run 3.0 Amps. PS35
115 VAC, 60 Hz, Start 3.8 Amps, Run 1.3 Amps.
Where is the serial # of my unit is located?
The serial # is located on the back of the stove.

1. Turndownthethermostat,letappliancecompletely
coolandthenunplugappliancebeforeservicing.
2. Theconvectionblowerislocatedontheooratthe
rearoftheappliance.
3. Liftthehopperlidupuntilitlocksintoplace.
4. Loosenthe4screwsontheupperbackpaneland
the 2 screws on the lower back panel, using a #2
Phillip Head screwdriver, a 3/8 inch wrench or a
3/8Inchsocket.Youdonotneedtoremovethem.
Figure 18.1.
5. Removetheleftupperandlowersidepanelsbylift-
ingupandout.Thehooksonthepanelswillslide
outoftheslotsontheappliance.Figure 18.2.
6. Release blower wires from the nylon wire retainer
if applicable.  Model ECO-ADV-PS35 has 2 black
wiresandModelECO-ADV-PS50andECO-CAB50
has1blackand1whitewirecomingfromtheblower.
7. Remove the wing bolt and move the blower and
hold-down bracket toward the back of the appli-
ance to release the locating tab. Figure 18.3.Pull
the blower out from under the convection plenum.
Slidethe blower outofthe appliance. Disconnect
the wires from the spade connectors at this time.
Figure 18.4.
8. Returnwirestonylonwireretainer.Makesurewires
donotcontactanymovingpartsortouch anysur-
facesthatmaybecomehot Figure 18.4.
A. Convection Blower Replacement
4Replacement Parts
Loosen Screws,
Do Not Remove
Figure 18.1
Figure 18.2
Figure 18.3
Figure 18.4
Locating Tab
Hold Down Bracket
Spade
Connectors
Upper Left
Panel
Lower Left Panel
Lift Up and Out of Slots
Nylon Wire
Retainer
Wing Screw

B. Exhaust Blower Replacement
1. Turndownthethermostat,letappliancecompletelycool
andthenunplugappliancebeforeservicing.
2. Removebothupperandlowerrightsidecurtains.Figure
18.2. on page 18.
3. Disconnect2whitewiresfromthewhiteandbluewiresof
theexhaustblower.
4. There is a removable plate on the exhaust blower.
Dependingon themodel,usea 1/4inchsocket,or 1/4
inchNutDriveror#2PhillipsHeadscrewdrivertoloosen
the6screwsinthekeyholeshapedholesandrotatethe
plate.Itisonlynecessarytoloosenscrews.Figure 19.1.
5. Removetheexhaustblowerandgasket.
6. Checkfordegradationonthegasketandreplaceifnec-
essaryusingthegasketincludedinthekit.
7. Re-installinreverseorder.
Figure 19.1
Exhaust Blower

Figure 20.2
C. Snap Disc Replacements
Figure 20.1
Snap Disc #1
Snap Disc #3
Snap Disc #2
Snap Disc #1 - Convection Blower
1.Turn down thermostat, let appliance cool completely if
running.Thenunplugappliancebeforeservicing.
2.Using#2Phillipsscrewdriver,3/8”wrench,or3/8”socket
loosen the three screws that hold the right upper and
lowersidepanels in place.You do not need toremove
thescrews.Removesidepanelsbyliftingupandout.
3.Snapdisc#1islocatedontheconvectionplenumbelow
thefeedmotor.Figure 20.1.
4.Ithastwopurplewiresattachedtoitwith1/4inchfemale
spadeterminals.
5.Disconnectthetwowiresfromthesnapdisc.Usinga#2
Phillipsscrewdriver,removethetwoscrewssecuringthe
snap disc to the appliance.
6.Re-installinreverse.
Snap Disc #2 - Fuel Delivery Interrupt
1.Turn down thermostat, let appliance cool completely if
running.Thenunplugappliancebeforeservicing.
2.Using#2Phillipsscrewdriver,3/8”wrench,or3/8”socket
loosen the three screws that hold the right upper and
lowersidepanelsinplace.Youdonot needtoremove
thescrews.Removesidepanelsbyliftingupandout.
3.Snapdisc#2islocatedontheconvectionplenuminthe
center of the appliance above the convection blower.
Figure 20.1.
4.Ithasablackwireandanorangewireattachedtoitwith
1/4inchfemalespadeterminals.
5.Disconnectthetwowiresfromthesnapdisc.Usinga#2
Phillipsscrewdriver,removethetwoscrewssecuringthe
snap disc to the appliance.
6.Re-installinreverse.
Snap Disc #3 - Feed Motor - Manual Reset
1.Turndownthermostat,letappliancecoolcompletelyifrun-
ning.Thenunplugappliancebeforeservicing.
2.Using #2 Phillipsscrewdriver, 3/8” wrench, or3/8”socket
loosenthethreescrewsthatholdtherightupperandlower
sidepanelsinplace.Youdonotneedtoremovethescrews.
Removesidepanelsbyliftingupandout.
3.Snapdisc#3islocatedonthebracketonthefeedtubenear
thefeedmotor.Figure 20.1.
4.Ithasatwograywiresattachedtoitwith1/4inchfemale
spadeterminals.
5.Thelocatingbracketisattachedtothefeedtubewithan8
X32wingnut.Removethewingnuttodetachthebracket
fromthefeedtube.
5.Disconnectthetwowiresfromthesnapdisc.
6.Usinga#2Philipsscrewdriver,removethescrewsecuring
the snap disc to the bracket. Figure 20.2.
7.Re-installinreverse.
Remove Screw
Snap Disc Bracket