Heatpol H+E Guide

USER MANUAL
HEATER CONTROLLER H+
HEATER
CONTROLLER
–
VERTICAL
ECONOMY
INSTALLATION MANUAL & USER MANUAL
HEATER CONTROLLER H+E

SAFETY:
1. The heater should be installed by a qualied person.
2. Bathroom radiators tted with electric heaters should be xed not less than 60 cm from
a bath, shower or wash basin, and never above abath.
3. For the heater permanently connected (hard wire) there must be applied a cut-off device
from the mains. Such a device must disconnect the heater from the supply mains in
2 poles, with contact separation of at least 3 mm.
4. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved
5. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
6. The heater MUST BE DISCONNECTED before cleaning the casing.
AVOID SOAKING THE CASING.
7. One radiator valve must always be open when a heater is in use (liquid thermal expansion).
CAUTION: To avoid the risk of re or electric shock the heater should be protected from water spray or ooding. This
appliance is not intended for use by persons (including children) of limited physical, sensory or mental abilities, or per-
sons inexperienced or not familiar with the appliance, unless supervised or instructed on the appliance use by persons
responsible for their safety. Particular attention should be paid to children, to preclude playing with the appliance by them.
Exclamation mark on triangular eld signals: information important for the user.
CAUTION: electric shock hazard!, lightning mark ended with arrow on triangular eld
CAUTION:
in order to reduce electric shock hazard, do not remove the casing (nor its rear cover). There are no user-
serviceable parts inside the appliance; the product must be returned to the manufacturer for repair via the distributor who
sold the product.
GUARANTEE TERMS:
Guarantee is granted by manufacturer for 24 months period star ting from date of sale, but no longer than 36 months from
date of the heater manufacture. Defects revealed within this period, resulting from a fault of manufacturer will be repaired
free of charge or the item replaced with new, equivalent one. Term of complaints’ investigation up to 14 (fourteen) days
from date of submission to the manufacturer.
Guarantee does not cover:
1. Using of product in a manner noncompliant with attached instructions.
2. Any visible damage to the heating element or controller due to improper use. Damaging of manufacturer’s seals makes
the guarantee null and void.
In the event that Heatpol are unable to repair or replace this product we reserve the right to refund the purchase price
as an alternative.
GUARANTEE CARD
Serial No.:
Date of sale:
Stamp of retail outlet, signature of seller
Caution: The guarantee card should be legibly lled in retail outlet. Any corrections on the guarantee card will invalidate
the guarantee. Guarantee card valid only with proof of purchase.
www.homeplus-system.com
www.homeplus-system.com
 2 ]

Kit content
USER MANUAL: Heating element + Heater controller (vertical) H+E
Mounting in radiators
Instllation options: central heating system Installation options:
electric radiator
S24 S24
230 V
1 2
Heating
element
Heater
controller
Allen
key
O/D shaped
color cover
Wall mount
plastic cover
>60cm>60cm
Purchase option
SAFETY:
1. The heater should be installed by a qualied person.
2. Bathroom radiators tted with electric heaters should be xed not less than 60 cm from
a bath, shower or wash basin, and never above abath.
3. For the heater permanently connected (hard wire) there must be applied a cut-off device
from the mains. Such a device must disconnect the heater from the supply mains in
2 poles, with contact separation of at least 3 mm.
4. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved
5. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
6. The heater MUST BE DISCONNECTED before cleaning the casing.
AVOID SOAKING THE CASING.
7. One radiator valve must always be open when a heater is in use (liquid thermal expansion).
CAUTION: To avoid the risk of re or electric shock the heater should be protected from water spray or ooding. This
appliance is not intended for use by persons (including children) of limited physical, sensory or mental abilities, or per-
sons inexperienced or not familiar with the appliance, unless supervised or instructed on the appliance use by persons
responsible for their safety. Particular attention should be paid to children, to preclude playing with the appliance by them.
Exclamation mark on triangular eld signals: information important for the user.
CAUTION: electric shock hazard!, lightning mark ended with arrow on triangular eld
CAUTION: in order to reduce electric shock hazard, do not remove the casing (nor its rear cover). There are no user-
serviceable parts inside the appliance; the product must be returned to the manufacturer for repair via the distributor who
sold the product.
GUARANTEE TERMS:
Guarantee is granted by manufacturer for 24 months period star ting from date of sale, but no longer than 36 months from
date of the heater manufacture. Defects revealed within this period, resulting from a fault of manufacturer will be repaired
free of charge or the item replaced with new, equivalent one. Term of complaints’ investigation up to 14 (fourteen) days
from date of submission to the manufacturer.
Guarantee does not cover:
1. Using of product in a manner noncompliant with attached instructions.
2. Any visible damage to the heating element or controller due to improper use. Damaging of manufacturer’s seals makes
the guarantee null and void.
In the event that Heatpol are unable to repair or replace this product we reserve the right to refund the purchase price
as an alternative.
GUARANTEE CARD
Serial No.:
Date of sale:
Stamp of retail outlet, signature of seller
Caution: The guarantee card should be legibly lled in retail outlet. Any corrections on the guarantee card will invalidate
the guarantee. Guarantee card valid only with proof of purchase.
Mników 322, 32-084 Morawica, Poland
Tel/fax: [phone]
www.homeplus-system.com
T-piece installed with
locshield valve
central connection one-pipe valve
connection
T-piece connection
with locshield valve
[ 3 ]

5
4
3-5cm
6A 7
Finishing
?
?
?
8
3
Electric radiators
CH system
6B
S22
Cut to length
S22
Element (D) must be cut
the correct lenght
Hard wire connection
For the heater perma-
nently connected (hard
wire) there must be
applied a cut-off device
from the mains. Such
a device must discon-
nect the heater from the
supply mains in 2 poles,
with contact separation
of at least 3 mm
9A
230 V
Connection with a coiled
cable and a plug
Live
Earth
Neutral
ON/OFF
Przełącznik
9A
230 V
After electric connection, turn on the switch
(concern only hard wire connection)
10
Option!
Purchase option!
Option!
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
 4 ]

USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
[ 5 ]

USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
RUN/SWITCH OFF the controller
4
ERRORS
5
USER MANUAL: ERRORS
Lack of water (or wrong choice of heating
element to the heater)
Damaged heating element
 6 ]

USER MANUAL: How to use heater controller H+
1
10˚C - 65˚C
Select temperature
+
–
Max heating temperature
Selection for 1/2/3 hours
Off selection
TURBO mode activation
3
sec +
–
TURBO mode activation –
max heating temperature
Hold button for 3 seconds
TIMER mode activation
3
+
–
1. Select temperature
2. Hold button “–” for 2 seconds
symbol will appear on the displayt1““
3. Using +/- buttons set the desired number of heater
work hours (1-9)
After the programmed time expires, the heater will
turn off
40˚C
Standard heating
temperature
3
sec
5
sec
DO NOT DISCONNECT!
controller from heating element, when connected to the power supply
ECONOMY
2
Run the controller
Hold upper button
for 3 seconds
Switch off the controller
Hold lower button
for 5 seconds
RUN/SWITCH OFF the controller
ERRORS