Heatpol HOME+ H+h WiFi User manual

HEAT SYSTEM
GUIDE & USER MANUAL
HEATER CONTROLLER H+h WiFi |REMOTE CONTROLER H+R
+
REMOTE
CONTROLLER
HEATER
CONTROLLER
–
HORIZONTAL
VERTICAL
•
E
C
O
D
E
S
I
G
N
•
R
E
A
D
Y
H+H_WIFI_EN0920

SAFETY:
1. The heater should be installed by a qualied person.
2. Bathroom radiators tted with electric heaters should be xed not less than 60 cm from
a bath, shower or wash basin, and never above abath.
3. For the heater permanently connected (hard wire) there must be applied a cut-off device
from the mains. Such a device must disconnect the heater from the supply mains in
2 poles, with contact separation of at least 3 mm.
4. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved
5. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
6. The heater MUST BE DISCONNECTED before cleaning the casing.
AVOID SOAKING THE CASING.
7. One radiator valve must always be open when a heater is in use (liquid thermal expansion).
CAUTION: To avoid the risk of re or electric shock the heater should be protected from water spray or ooding. This
appliance is not intended for use by persons (including children) of limited physical, sensory or mental abilities, or per-
sons inexperienced or not familiar with the appliance, unless supervised or instructed on the appliance use by persons
responsible for their safety. Particular at tention should be paid to children, to preclude playing with the appliance by them.
Exclamation mark on triangular eld signals: information important for the user.
CAUTION: electric shock hazard!, lightning mark ended with arrow on triangular eld
CAUTION:
in order to reduce electric shock hazard, do not remove the casing (nor its rear cover). There are no user-
serviceable parts inside the appliance; the product must be returned to the manufacturer for repair via the distributor who
sold the product.
GUARANTEE TERMS:
Guarantee is granted by manufacturer for 24 months period star ting from date of sale, but no longer than 36 months from
date of the heater manufacture. Defects revealed within this period, resulting from a fault of manufacturer will be repaired
free of charge or the item replaced with new, equivalent one. Term of complaints’ investigation up to 14 (fourteen) days
from date of submission to the manufacturer.
Guarantee does not cover:
1. Using of product in a manner noncompliant with attached instructions.
2. Any visible damage to the heating element or controller due to improper use. Damaging of manufacturer’s seals makes
the guarantee null and void.
In the event that Heatpol are unable to repair or replace this product we reserve the right to refund the purchase price
as an alternative.
GUARANTEE CARD
Serial No.:
Date of sale:
Stamp of retail outlet, signature of seller
Caution: The guarantee card should be legibly lled in retail outlet. Any corrections on the guarantee card will invalidate
the guarantee. Guarantee card valid only with proof of purchase.
Mników 322, 32-084 Morawica, Poland
Tel/fax: [phone]
www.homeplus-system.com
www.homeplus-system.com
 2 ]

SAFETY:
1. The heater should be installed by a qualied person.
2. Bathroom radiators tted with electric heaters should be xed not less than 60 cm from
a bath, shower or wash basin, and never above abath.
3. For the heater permanently connected (hard wire) there must be applied a cut-off device
from the mains. Such a device must disconnect the heater from the supply mains in
2 poles, with contact separation of at least 3 mm.
4. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved
5. Children shall not play with the appliance. Cleaning and user maintenance shall not be
made by children without supervision.
6. The heater MUST BE DISCONNECTED before cleaning the casing.
AVOID SOAKING THE CASING.
7. One radiator valve must always be open when a heater is in use (liquid thermal expansion).
CAUTION: To avoid the risk of re or electric shock the heater should be protected from water spray or ooding. This
appliance is not intended for use by persons (including children) of limited physical, sensory or mental abilities, or per-
sons inexperienced or not familiar with the appliance, unless supervised or instructed on the appliance use by persons
responsible for their safety. Particular at tention should be paid to children, to preclude playing with the appliance by them.
Exclamation mark on triangular eld signals: information important for the user.
CAUTION: electric shock hazard!, lightning mark ended with arrow on triangular eld
CAUTION: in order to reduce electric shock hazard, do not remove the casing (nor its rear cover). There are no user-
serviceable parts inside the appliance; the product must be returned to the manufacturer for repair via the distributor who
sold the product.
GUARANTEE TERMS:
Guarantee is granted by manufacturer for 24 months period star ting from date of sale, but no longer than 36 months from
date of the heater manufacture. Defects revealed within this period, resulting from a fault of manufacturer will be repaired
free of charge or the item replaced with new, equivalent one. Term of complaints’ investigation up to 14 (fourteen) days
from date of submission to the manufacturer.
Guarantee does not cover:
1. Using of product in a manner noncompliant with attached instructions.
2. Any visible damage to the heating element or controller due to improper use. Damaging of manufacturer’s seals makes
the guarantee null and void.
In the event that Heatpol are unable to repair or replace this product we reserve the right to refund the purchase price
as an alternative.
GUARANTEE CARD
Serial No.:
Date of sale:
Stamp of retail outlet, signature of seller
Caution: The guarantee card should be legibly lled in retail outlet. Any corrections on the guarantee card will invalidate
the guarantee. Guarantee card valid only with proof of purchase.
Mników 322, 32-084 Morawica, Poland
Tel/fax: [phone]
www.homeplus-system.com
USER MANUAL: Heating element + Heater controller (horizontal) H+h
GLUE
15 min
Side connection
Kit content
Mounting in radiators CH system
Instllation details
Electric radiators
Heater
controller
Heating element
+
_
System option:
Remote controller
Wall clip
The electric heater
must have a safety valve
1
Before you apply the heating element, spread the Loctite
glue (included in the set) on the middle of the thread
circumference.
GLUE
S24
230 V
min. 25mm
C
C
2The order of assembly of elements
Allen
key
C
Option:
plastic
overlay
mask
Right side
Left side
Heating element
Heating element
Heating element
Vertical
connection
180˚
Position change
Movable elements
Back
180˚
180˚
Front
[ 3 ]

3-5cm
5A
Electric radiators CH system
5B
4
230 V
CAUTION! Do not disconnect heater
controller when the system is powered.
The locking screw must be protected
against accidental unscrewing eg. by
applying a drop of lacquer or acrylic
adhesive.
Before you apply the heating element, spread the Loctite
glue (included in the set) on the middle of the thread
circumference.
6A
230V
6B
230V
Live
Earth
Neutral
For the heater permanently
connected (hard wire) there
must be applied a cut-off
device from the mains.
Such a device must disconnect
the heater from the supply
mains in 2 poles, with contact
separation of at least 3 mm
7
After electric connection, turn on the switch
ON/OFF
Switch
ON/OFF
Switch
15 cm
3
C
 4 ]

Instllation options: CH system Installation options:
electric radiator
1 2
Mounting in radiators
S24 S24
230 V
USER MANUAL: Heating element + Heater controller (horizontal/vertical) H+h
>60cm>60cm
Installation details
[ 5 ]

USER MANUAL: Howtouse heater controller(optionalremotecontroller)
VIDEOavailableatwww.homeplus-system.com
Connect heater controller to the heater
Use manufacturer recommendation
Turn ON the controller
ON/OFF
Heatercontroller
–
+
Heater
controller
display
LED (Activity)
Heatercontroller Remotecontroller
LED activity: heating element is working
1x
1x
3
sec During countdown
within 30 seconds
Reverse remote controller.
Push pairing button!
Pairing fi nished!
Remote controller
is already working Allen key
included
Hold 3 sec.
Start countdown
Press once
upper and lower
button together
Prepare remote controller + allen key for use
Remotecontroller
Pairing button
for allen key (F)
Back
Magnet clip Wall clip mounting
for allen key (F)
Wall clip mounting
Push for pairing button using
allen key to activate the controller
Due to proper
temperature reading
do not place
a remote controller
(temperature sensor)
over radiators,
next to doors
or in sunny places.
Locate suitable place to mount the remote
START:Heatercontrollerandremotecontrollerpairing
IfyouboughtaremotecontrollertogetherwithH+heateryou do not need to pair it!
1
USER MANUAL: Howtouse heater controller(optionalremotecontroller)
VIDEOavailableatwww.homeplus-system.com
Connect heater controller to the heater
Use manufacturer recommendation
Turn ON the controller
ON/OFF
Heatercontroller
–
+
Heater
controller
display
LED (Activity)
Heatercontroller Remotecontroller
LED activity: heating element is working
1x
1x
3
sec During countdown
within 30 seconds
Reverse remote controller.
Push pairing button!
Pairing fi nished!
Remote controller
is already working Allen key
included
Hold 3 sec.
Start countdown
Press once
upper and lower
button together
Prepare remote controller + allen key for use
Remotecontroller
Pairing button
for allen key (F)
Back
Magnet clip Wall clip mounting
for allen key (F)
Wall clip mounting
Push for pairing button using
allen key to activate the controller
Due to proper
temperature reading
do not place
a remote controller
(temperature sensor)
over radiators,
next to doors
or in sunny places.
Locate suitable place to mount the remote
START:Heatercontrollerandremotecontrollerpairing
IfyouboughtaremotecontrollertogetherwithH+heateryou do not need to pair it!
1
Hard wire connection
Finishing
Electric radiators
CH system
5
3-5cm
6A 7
S22 S22
6B
For the heater perma-
nently connected (hard
wire) there must be
applied a cut-off device
from the mains. Such
a device must discon-
nect the heater from the
supply mains in 2 poles,
with contact separation
of at least 3 mm
9B
230 V
Connection with a coiled cable and a plug
4
230 V
CAUTION! Do not disconnect
heater controller when the system
is powered.
Live
Earth
Neutral
ON/OFF
Switch
9A
230 V
After electric connection, TURN ON the switch
(concern only hard wire connection)
10
ON/OFF
Switch
3
Recommendation:
Plug and turn
front of the heater
controller
to vertical position
90°
 6 ]

USER MANUAL: Howtouse heater controller(optionalremotecontroller)
VIDEOavailableatwww.homeplus-system.com
Connect heater controller to the heater
Use manufacturer recommendation
Turn ON the controller
ON/OFF
Heatercontroller
–
+
Heater
controller
display
LED (Activity)
Heatercontroller Remotecontroller
LED activity: heating element is working
1x
1x
3
sec During countdown
within 30 seconds
Reverse remote controller.
Push pairing button!
Pairing fi nished!
Remote controller
is already working Allen key
included
Hold 3 sec.
Start countdown
Press once
upper and lower
button together
Prepare remote controller + allen key for use
Remotecontroller
Pairing button
for allen key (F)
Back
Magnet clip Wall clip mounting
for allen key (F)
Wall clip mounting
Push for pairing button using
allen key to activate the controller
Due to proper
temperature reading
do not place
a remote controller
(temperature sensor)
over radiators,
next to doors
or in sunny places.
Locate suitable place to mount the remote
START:Heatercontrollerandremotecontrollerpairing
IfyouboughtaremotecontrollertogetherwithH+heateryou do not need to pair it!
1
For H+h WiFi controller please download smartphone application from
www.supla.org and follow the instruction.
USER MANUAL: Howtouse heater controller(optionalremotecontroller)
VIDEOavailableatwww.homeplus-system.com
Connect heater controller to the heater
Use manufacturer recommendation
Turn ON the controller
ON/OFF
Heatercontroller
–
+
Heater
controller
display
LED (Activity)
Heatercontroller Remotecontroller
LED activity: heating element is working
1x
1x
3
sec During countdown
within 30 seconds
Reverse remote controller.
Push pairing button!
Pairing fi nished!
Remote controller
is already working Allen key
included
Hold 3 sec.
Start countdown
Press once
upper and lower
button together
Prepare remote controller + allen key for use
Remotecontroller
Pairing button
for allen key (F)
Back
Magnet clip Wall clip mounting
for allen key (F)
Wall clip mounting
Push for pairing button using
allen key to activate the controller
Due to proper
temperature reading
do not place
a remote controller
(temperature sensor)
over radiators,
next to doors
or in sunny places.
Locate suitable place to mount the remote
START:Heatercontrollerandremotecontrollerpairing
IfyouboughtaremotecontrollertogetherwithH+heateryou do not need to pair it!
1
[ 7 ]

Errors
Settingswaterorambienttemperature Errors
Max heating temperature, selection for 1/2/3 hours
Off selection
TURBOmodeactivation
3
sec
+
–
TURBO mode activation - max heating temperature
Hold button for 3 seconds
4
Run the heater controller
via remote controller
Hold upper button
for 3 seconds
Switch off the controller
via remote controller
Hold lower button
for 5 seconds
40˚C
Standard heating
temperature
3
sec
5
sec
2
10˚C - 65˚C*
Select temperature
+
–
3
DO NOT DISCONNECT!
controllerfromheatingelement,whenconnected
tothepowersupply
Lack of water (or wrong choice
of heating element to the heater)
Damaged heating element
(or no power cuircit)
No communication to the remote
controller if paired
Press twice
upper and lower
button together
2x
2x
Temperature selection.
+
–
The remote is
a temperature sensor
* maximum temperature can be different
according to the producer settings
Water
temperature 10-65˚C*
Ambient
temperature 10-30˚C
 8 ]

Errors
Settingswaterorambienttemperature Errors
Max heating temperature, selection for 1/2/3 hours
Off selection
TURBOmodeactivation
3
sec
+
–
TURBO mode activation - max heating temperature
Hold button for 3 seconds
4
Run the heater controller
via remote controller
Hold upper button
for 3 seconds
Switch off the controller
via remote controller
Hold lower button
for 5 seconds
40˚C
Standard heating
temperature
3
sec
5
sec
2
10˚C - 65˚C*
Select temperature
+
–
3
DO NOT DISCONNECT!
controllerfromheatingelement,whenconnected
tothepowersupply
Lack of water (or wrong choice
of heating element to the heater)
Damaged heating element
(or no power cuircit)
No communication to the remote
controller if paired
Press twice
upper and lower
button together
2x
2x
Temperature selection.
+
–
The remote is
a temperature sensor
* maximum temperature can be different
according to the producer settings
Water
temperature 10-65˚C*
Ambient
temperature 10-30˚C
DOWNLOAD APPLICATION SUPLA.ORG
Install the application on your devices.
The app will easily guide you through
individual installation steps.
[ 9 ]

Mników 322, 32-084 Morawica, Polska
Tel/fax: [phone]
www.heatpol.pl
www.homeplus-system.com