MULTISPAN PID 4201-1C User manual

POWER ON
All digit segment will be turned ON for 1 sec
Previous or default sensor input and control action will be
displayed for 2 sec
Process Value
Current
8 8 8 8....
J
25
8
D
8
I
8
p
8....
0.0
PID/ ON-OFF (selectable)
Output
Power Supply
Operating
Temperature
Relative
Humidity
100 to 250V AC,50/60 Hz, Approx 3VA
0°C To 55°C
Up to 95% RH Non Condensing
Model
Display
Size (mm)
Panel Cutout
Input
Control Action
48 (H) X 48 (W) X 95 (D) mm
45 X 45 mm
PID-4201-1C
J ,K ,PT,PT.1
Protection
Level IP-65 (Front side) As per IS/IEC 60529 : 2001
Temperature:J type: 0 to 600°C/ K type: 0 to 1200°C
PT type: -99 to 400°
Ampere : 0.0 to 30.0 A (1 CT)
Range
TechnicalSpecification
Working:-
ProductManual
MultispanControlInstrumentsPvtLtd
72/B,Phase1,GIDCEstate,Vatva,Ahmedabad-382445,Gujarat,India.
[phone]
PID4201-1C
www.multispanindia.com
[email protected]
PIDCONTROLLER
Page-1
PID-4201-1C www.multispanindia.com
1) If Sensor Connection is reverse, Display will show “SRE” message.
2) If Sensor is not connected, Display will show Open message.
3) While pressing key for 5 Sec. Lower Display start scrolling and show set
Temperature (For Exa. ‘150’,150°is setpoint) and ampere
(For Exa. ‘A 08.0’, 8 Amp is actual current).
4) If key press for 5 Sec. Then lower Display hold on any one value, To show
other value press key.
5) Every time the instrument is turned ON, Following pattern will be displayed
C /PT.1:- -99.9 to 400.0
UPPER:- 4 Digit 7 seg 0.56”, Red LED Display
LOWER:- 4 Digit 7 seg 0.33”, green LED Display
1relay parallel SSR,230V AC,5A;SSR,12V DC,30mA

Press key to
save & exit
ENT
Press key to
save & exit
ENT
SET
Set Point
Password Message
Press key for 4 sec to
enter Password
SET
SET
ENT
Process Value
Password Message
Press key
ENT
TO ENTER BASIC
CONFIGURATION
SETTING, ENTER “73”
Basic Configuration
Set Point Setting
Set Value
Control Parameter
TO ENTER CONTROL
PARAMETER
SETTING, ENTER “37”
(If R1MD = PID)
1) Press key to go parameter setting.
SET
3) Press key to save change in setting
4) Press key for 6 sec to start/stop PID AUTO TUNING
5) Press + key for 3 sec to go to factory setting mode.
2) Press or key to change value or to select option.
Key Operation
SET
Factory Setting
ENT
ENT
yes : press key to apply factory set
values as shown in table.
nO : press key to escape
from factory setting.
Select on/off value & press key
to turn on/off heater
Press + key
for 3 sec
Press + key for
4 sec for Heater on/off
FACTORY SETTING
PARAMETER
IT
CT
MR
HYSTERESIS
PB
DT
VALUES
300
15 SEC.
20.0
75
0°C
3°0
SR.
2
4
OFFSET
6
1
3
5
7
0°C
PIDAUTO-TUNING
Presskeyfor6sectostart/stop
PIDauto-tuning
C
PV
R
Current
°
Page-2
PID-4201-1C www.multispanindia.com
(0.0 to 30.0)
Press key
ENT
(-20 to 20)

HBI
ON
DT
SHL
OFF
CT
SLL
PB
IT
ON-OFF Action
PID Action
ON
OFF
Proportional Band for PID Action
Integral Time for PID Action
Derivative Time for PID Action
Set High Limit
Set Low Limit
Cycle Time for PID Action
Password
Offset
Heater
ON0F
PID
RMOD Relay Mode
J
J
HYS Hysterisis
Heater break indicator
PT.1
PT
K
PT
PT.1
INPT
Sr.
1
1
Sr
2
2
3
3
5
4
4
5
6
7
8
96
7
13
10
14
17
11
15
18
12
Input
Parameter Description
PASS
OFCT
HTR
16
19
20
21
CT
HYS
IT
MR
DT
Off-set correction
PB
Parameter
Range of the parameter
0.0 to 999.9
Range for J,K,PT
0 to 9999
0 to 9999
4 sec to 99 sec
-9 to +9
-20°C To 20°C
1 to 100
Page-3
PID-4201-1C www.multispanindia.com

Product improvement and upgrade is a constant procedure. So for more updated operating information and support,
Please contact our helpline : [phone]/76/82 or Email at ser[email protected] Ver: 1912
Connection Diagram Connection Diagram All safety related codifications, symbols and instructions that appear in this operating manual
or on the equipment must be strictly followed to ensure the safety of the operating personnel as
well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might impair the
protection provided by the equipment .
=> Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires
should have insulations capacity made of at least 1.5kV.
2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of
equal size shall be made with shortest connection.
4) When extending the thermocouple lead wires, always use thermocouple compensation wires for wiring
for the RTD type, use a wiring material with a small lead resistance (5Ω max per line)and no resistance
differentials among three wires should be present.
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the
wiring arrangement. Do not touch the terminals while power is being supplied.
5) A better anti-noise effect can be expected by using standard power supply cable for
the instrument.
1) This equipment, being built-in-type, normally becomes a part of main control panel and such in case the
terminals do not remain accessible to the end user after installation and internal wiring.
2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product
or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.
3) Circuit breaker or mains switch must be installed between power source and supply terminal to
facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be
installed at convenient place normally accessible to the operator.
4) Use and store the instrument within the specified ambient temperature and humidity ranges as
mentioned in this manual.
Warning Guidelines
Installation Guidelines
Mechanical Installation
Maintenance
Safety Precautions
1) Prepare the panel cutout with proper dimensions as show above.
2) Fit the unit into the panel with the help of clamp given.
3) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the
screws on the terminal block using the tightening torque of the range of 1.2 N.m.
5) Do not connect anything to unused terminals.
1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any
other cleaning agent.
3) Fusible resistor must not be replaced by operator.
2
A
B
C
D
EF
MODEL A
48mm 48mm 45mm 45mm 3mm 95mm
BC
D E F
DIMENSIONS
68mm - 2.68 inches
60mm - 2.36 inches
Page-4
PID-4201-1C www.multispanindia.com
PID4201-1C-RG
T/C
+
+
RTD
-
-
NC
C
R
NO
SSR
100
250VAC

1
2
3
4
5
L
N
6
7
8
9
10
~
50/60HZ
3VA
www.multispanindia.com
H1
CT
COM.
!
Made in India