Helwett Packard HPE Aruba Networking 9114 User manual

HPE Aruba Networking 9114
Gateway
Installation Guide

HPE Aruba Networking 9114 Gateway | Installation Guide 0512273-01 | October 2023
Copyright Information
© Copyright 2023 Hewlett Packard Enterprise Development LP.
Open Source Code
This product includes code licensed under certain open source licenses which require source compliance.
The corresponding source for these components is available upon request. This offer is valid to anyone in
receipt of this information and shall expire three years following the date of the final distribution of this
product version by Hewlett Packard Enterprise Company. To obtain such source code, please check if the
code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if
not, send a written request for specific software version and product for which you want the open source
code. Along with the request, please send a check or money order in the amount of US $10.00 to:
Hewlett Packard Enterprise Company
Attn: General Counsel
WW Corporate Headquarters
1701 E Mossy Oaks Rd Spring, TX 77389
United States of America

Contents
Contents 1
About This Guide 2
Guide Overview 2
Related Documentation 2
Contacting Support 2
HPE Aruba Networking 9114 Gateway 3
Package Checklist 3
HPE Aruba Networking 9114 Gateway Components 3
Power, Status, and Gateway LEDs 4
Reset Button 5
Access Ports 5
RJ-45 Console Port 7
USB Type-C Console Port 8
Management Port 8
USB Interface 9
Expansion Slot 9
Grounding Point 9
Fan Module 9
PSU Slot 0 10
PSU Slot 1 11
Installation 12
Precautions 12
Selecting a Location 13
Rack mount Installation - Standard 13
Rack mount Installation - Mid 15
Four Post Rack mount Installation 17
Table or Shelf Installation 19
Installing and Removing a Fan Module 19
Installing and Removing a Power Supply 20
Connecting and Disconnecting the AC Power Cord 24
Connecting the DC Power Cord 25
Installing and Removing an SFP Module 26
Connecting and Disconnecting an LC Cable 26
Specifications, Safety, and Compliance 28
HPE Aruba Networking 9114 Gateway Specifications 28
Regulatory Model Name 28
Safety and Regulatory Compliance 28
Proper Disposal of HPE Aruba Networking Equipment 31
HPE Aruba Networking 9114 Gateway |Installation Guide 1
Contents

Chapter 1
About This Guide
HPE Aruba Networking 9114 Gateway |Installation Guide 2
About This Guide
This document describes the hardware features of the HPE Aruba Networking 9114 Gateway. It provides a detailed
overview of the physical and performance characteristics of each gateway model and explains how to install the
gateway and its accessories.
Guide Overview
nHPE Aruba Networking 9114 Gateway provides a detailed hardware overview of the HPE Aruba Networking
9114 Gateway and each of its components.
nInstallation describes how to install the HPE Aruba Networking 9114 Gateway in a number of ways and how to
install each of its components.
nSpecifications, Safety, and Compliance lists the HPE Aruba Networking 9114 Gateway's technical specifications
and safety and regulatory compliance information.
Related Documentation
You require the following documents for the complete management of HPE Aruba Networking gateway.
nLatest document of the software user guide:
https://www.arubanetworks.com/techdocs/ArubaDocPortal/content/cons-aos-home.htm
nCLI bank: https://www.arubanetworks.com/techdocs/CLI-Bank/Content/landing-pages/aos8-home.htm
Contacting Support
This section includes the contact information for the HPE Aruba Networking 9114 Gateway.
Table 1: Contact Information
Main Site www.arubanetworks.com
Support Site https://asp.arubanetworks.com
Airheads Social Forums and
Knowledge Base
www.community.arubanetworks.com
North American Telephone [phone] (Toll Free)
1-408-754-1200
International Telephones https://www.arubanetworks.com/support-services/contact-support/
Software Licensing Site www.hpe.com/networking/support
End of Support information www.arubanetworks.com/support-services/end-of-life/
Security Incident Response Team
(SIRT)
Site: https://www.arubanetworks.com/support-services/security-
bulletins/
Email: [email protected]

Chapter 2
HPE Aruba Networking 9114 Gateway
HPE Aruba Networking 9114 Gateway |Installation Guide 3
HPE Aruba Networking 9114 Gateway
The HPE Aruba Networking 9114 Gateway is a high-performance edge appliance with the ability to perform
intelligent routing and tunnel orchestration software or wireless control plane management for SASE security and
scalability.
Package Checklist
Inform your supplier to check if there are any incorrect, missing, or damaged parts. If possible, retain the carton,
including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.
Table 2: Package Contents
Item Quantity
HPE Aruba Networking 9114 Gateway 1
Mounting Brackets 2
M6 x 15 mm Phillips Pan Head Screws 4
M4 x 8 mm Phillips Flat Head Screws 8
M6 x 7 mm Grounding Screws 2
Power Cable
Power cable is shipped with only AC SKU.
No power cable is shipped with DC SKU.
1
USB Type-C Console Cable 1
Rubber Feet 4
Optional accessories are available for use with the HPE Aruba Networking 9114 Gateway series and
are sold separately. Contact your HPE Aruba Networking sales representative for details and
assistance
HPE Aruba Networking 9114 Gateway Components
This section introduces the different component and its location in the HPE Aruba Networking 9114 Gateway.
The following figure shows the front and rear panel of the HPE Aruba Networking 9114 Gateway.
Figure 1 Front Panel of HPE Aruba Networking 9114 Gateway

HPE Aruba Networking 9114 Gateway |4
Table 3: Components of HPE Aruba Networking 9114 Gateway Front Panel
Callout Component Description Page
1Power LED Used for basic monitoring of the HPE Aruba
Networking 9114 Gateway
page 4
Status LED
Gateway LED
2 Reset Configuration button Used to reset the configuration settings page 5
3 Access Ports There are 2 types of access ports:
n4 x 1G Combo ports (1G SFP or 10/100/1000M
Base-T)
n4 x 10G SFP+ ports (10G/1G SFP)
page 5
4 RJ-45 Console Port RJ-45 serial console access port page 7
5 USB Type-C Console Port Provides console access for direct local access page 8
6 Management Port An out of band management port (RJ-45), used to
connect to a separate management network
page 8
7 USB3.0 Interfaces 2 x USB3.0 interfaces. USB storage device can be
used to save and upload configurations
page 9
8 Expansion Slot Reserved for future use page 9
Figure 2 Back Panel of the HPE Aruba Networking 9114 Gateway
Table 4: Components of HPE Aruba Networking 9114 Gateway Back Panel
Callout Component Description Page
1 PSU Slot 0 Primary power supply module page 10
2 Grounding Points Used to attach the grounding screws page 9
3 Fans 3 x hot-swappable high speed fans page 9
4 Cable Clip 2 x Cable clip to secure the Power cord
5 PSU Slot 1 Slot for additional power supply module page 11
Power, Status, and Gateway LEDs

In addition to the LEDs on each port, there are three additional LEDs on the front panel that provides the overall
status of the device. These LEDs provide basic monitoring of the overall status of the HPE Aruba Networking 9114
Gateway.
Table 5: Power, Status, and Gateway LEDs
LED Symbol Function Indicator Status
Power System power Green (Solid) Unit is powered
on
Off Unit is powered
off
Amber (Solid) Unit is in error
state
Status System status Green (Solid) Unit is operational
Green (Blinking) Device is loading
software
Amber (Blinking) Major alarm
Amber (Solid) Critical alarm
Off No power
Gateway Gateway Operation Mode Green (Solid) The unit is
connected to
Network
Management
System
Off Power Off
Reset Button
The HPE Aruba Networking 9114 Gateway includes a reset button for resetting the gateway configurations. Insert a
pin into the reset button hole until you feel the pin touches a surface. Push and hold the pin for two seconds to
reset the gateway configuration.
Access Ports
The HPE Aruba Networking 9114 Gateway is equipped with following access ports:
n4 x 1G Combo ports (1G SFP or 10/100/1000M Base-T)
HPE Aruba Networking 9114 Gateway does not support 1G copper SFP in dual-media 1G SFP ports.
If 1G copper SFPs are connected during the boot-up or run-time process, it may lead to
unpredictable or inconsistent behavior on the gateway.
n4 x 10G SFP+ ports (10G/1G SFP)
Use 10G SFP+ ports with SFP/SFP+ modules and 1G combo SFP ports with 1G SFP modules that HPE Aruba
Networking supports. 10G SFP ports support the operation of two speeds (10G or 1G).
HPE Aruba Networking 9114 Gateway |Installation Guide 5

HPE Aruba Networking 9114 Gateway |6
HPE Aruba Networking tests and supports HPE Aruba Networking optics within their gateway systems.
HPE Aruba Networking does not guarantee the proper functionality of third-party optics if used with a
HPE Aruba Networking system since the third-party optics have not been tested or supported.
Access Port LEDs
The two LEDs on each access port allow you to monitor the status of and activity on the port. These LEDs provide
basic monitoring of the status, activity, and basic configuration of each port.
nLINK/ACT: on the left side of the port, it displays the link status of the port.
nSPEED: on the right side of the port, it displays the speed of the port. The following table describes the LED
behavior for each mode.
Table 6: 10G SFP+ Access Port
LED Function Indicator Speed Status
LINK/ACT Link status Green (Solid) Link has been established
Green (Blinking) Port is transmitting or receiving
data
Off No link on port
SPEED Port speed status Green (Solid) 10G speed
Amber (Solid) 1G speed
Off No link on port
Table 7: 1G Combo port
LED Function Indicator Speed status
LINK/ACT Link status Green (Solid) Link has been established
Green (Blinking) Port is transmitting or receiving
data
Off No link on port
SPEED Port speed status Green (Solid) 1G speed
Off No link on port

Table 8: 1G Combo RJ45 port
LED Function Indicator Speed Status
LINK/ACT Link status Green (Solid) Link has been established
Green (Blinking) Port is transmitting or receiving
data
Off No link on port
SPEED Port speed status Green (Solid) 1G speed
Off 100M/10M speed
RJ-45 Console Port
The serial console port allows connecting a gateway to a terminal or a laptop for direct local management. This port
is a RJ-45 female connector with the pin-out described in the following figure.
Figure 3 Serial Console Port Pin-Out
Serial
Console Port
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
Direction
Input
Output
GND
Communication settings for the serial console port are indicated in the following table.
Table 9: Console Terminal Settings
Baud Rate Data Bits Parity Stop Bits Flow Control
9600 8 None 1 None
The CONSOLE port is compatible only with RS-232 devices. Non-RS-232 devices, such as APs, are not
supported.
HPE Aruba Networking 9114 Gateway |Installation Guide 7

HPE Aruba Networking 9114 Gateway |8
Do not connect the Console port to an Ethernet switch or a PoE power source. This may damage the
gateway.
Serial Console Port Adapter
A modular adapter can be used to convert the RJ-45 (female) connector to a DB9 (male) connector. Refer to
following figure for complete details.
Figure 4 RJ-45 (female) to DB9 (male) Modular Adapter Conversion
3
4
5
2
5
6 3
RJ-45 DB-9
Internal
Connections
TxD
GND
RxD
1
2
3
4
5
6
7
8
TxD
GND
RxD
RJ-45 Female
Pin-Out
DB-9 Male
Pin-Out
TxD
RxD
Ground
5
4
3
2
1
9
8
7
6
USB Type-C Console Port
The HPE Aruba Networking 9114 Gateway has one USB type-C console port that provides console access for direct
local access. If both USB and RJ-45 console ports are connected, the USB connection takes precedence over the RJ-
45 console connection.
Using the USB Console Port
To use the USB type-C console port, follow these steps:
1. Download and install the USB driver file as follows:
a. Go to https://asp.arubanetworks.com.
b. Click on the Software & Document tab.
c. Under the Product section click Show All.
d. Select Aruba Mobility Gateways and click Apply.
e. Search Driver in the search box.
f. In the search result, according to your operating system, choose Windows Driver for USB Console
port or MacBook Driver for USB Console port.
g. Download and install the driver to your PC.
2. Use the USB Type C connector cable, which is included in the package, to connect the gateway and your PC.
a. Connect its Type A connector to a USB port on your PC.
b. Connect its Type C connector to the USB console port on the gateway.
Management Port
The HPE Aruba Networking 9114 Gateway has a 10/100/1000BASE-T Gigabit Management (RJ-45) port.
The management port provides 10/100/1000 Mbps Ethernet access to the HPE Aruba Networking 9114 Gateway
CLI, SNMP, and Web interface for complete system management and troubleshooting. It can also be used to
connect to a separate management network.
The management port has a LINK/ACT LED on its left side, and a SPEED LED on its right side. During operation,
these LEDs provide status information as shown in the following table: