Hertz marine HCP 1MDK User manual

rev 1.5
hertzaudiovideo.com
USER’S MANUAL
AMPLIFIER
HCP 1MDK
HCP 2MX
HCP 4M
HCP 4MDK
HCP 5MD
HCP 5MD-24V
Il Manuale Utente è disponibile
anche sul nostro sito
www.hertzaudiovideo.com
The User Manual is also
available from our web site
www.hertzaudiovideo.com

User’s Manual
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
Index
1. PACKAGING CONTENTS 6
2. PRECAUTIONS 7
3. INSTALLATION AND SIZES 35
4. CABLE SIZE CALCULATION TABLES. 1: POWER SUPPLY / 2: SPEAKERS 35
5. POWER SUPPLY and REMOTE IN CONNECTION / FUSE REPLACEMENT 36
6. SUBWOOFER REMOTE VOLUME CONTROL: HRC INSTALLATION 37
7. PRE IN / SPEAKER IN / PRE OUT 38
8. AUTO TURN-ON BY SPEAKER IN (without REMOTE IN) 43
9. INSTALLATION EXAMPLES:
HCP 1MDK:(1CH) FILTERED SUBWOOFER 45
HCP 2MX:(2CH) FRONT L / R 46
(1CH) SUBWOOFER L+R 47
(1CH) SUBWOOFER MONO INPUT 48
HCP 4M: (4CH) FRONT + REAR 49
(3CH) FRONT + SUB 50
(2CH) LEFT + RIGHT 51
HCP 4MDK:(4CH) FRONT + REAR 52
(3CH) FRONT + SUB 53
(2CH) LEFT + RIGHT 54
HCP 5MD / HCP 5MD-24V:
(5CH) FRONT + REAR + SUB 55
(5CH) WOOFER + TWEETER + SUB 56
(3CH) FRONT + SUB 57
10. BLOCK DIAGRAMS
HCP 1MDK:58
HCP 2MX: 59
HCP 4M: 60
HCP 4MDK:61
HCP 5MD / HCP 5MD-24V:62
11. TECHNICAL SPECIFICATIONS
HCP 1MDK:63
HCP 2MX: 63
HCP 4M: 64
HCP 4MDK:64
HCP 5MD: 65
HCP 5MD-24V: 65

7
User’s Manual
20 A
x 1 x 1x 2
x 1
x 4
x 1
4 mm 2 mm
x 1
30 A
x 1 x 1x 3
x 1
x 4
x 1
4 mm 2 mm
x 1
HCP 2MX
HCP 1MDK
HCP 4M
HCP 4MDK
HCP 5MD
HCP 5MD-24V
25 A x 1 x 1
x 2
x 1
x 3
4 mm 2 mm
x 4
x 1
15 A
x 2
only for
HCP 5MD-24V
x 1 x 1
x 1
x 2
4 mm 2 mm
x 4
x 1
x 2
20 A
35 A
for HCP 4MDK
x 2x 2
1PACKAGING CONTENTS

14
English / English
Before installing the components, please carefully read all of the instructions contained in this manual. It is advisable to carefully
follow the highlighted instructions. Failure to respect these instructions may cause unintentional harm or damage to the components.
SAFETY CONSIDERATIONS
1. Check your alternator and battery condition to ensure they can handle the increased consumption.
2. Do not carry out any installation inside the engine compartment or exposed to water, excessive humidity, dust or dirt.
3. Never run cables outside the vehicle/vessel or install the amplifier next to electronic gearcases.
4. Install the amplifier in the vehicle/vessel sections where temperature is between 0°C (32°F) and 55°C (131°F). Let the amplifier outer profile be at
least 5 cm (2”) far from possible walls. There must be good air circulation where the amplifier is installed. If you cover the heat sink, the amplifier
goes in protection.
5. The amplifier can reach temperatures of around 80°C (176°F). Make sure it is not dangerously hot before touching it.
6. Periodically clean the amplifier without using aggressive solvents that might damage it. Don’t use compressed air, since it would push solid parts in the
amplifiers. Dampen a piece of cloth with water and soap, wring it and clean the amplifier. Then use a piece of cloth dampened with water only;
eventually clean the amplifier with a dry piece of cloth.
7. Make sure the location you chose for the components does not affect the correct functioning of the vehicle/vessel mechanical and electrical
devices. This amplifier was designed for installation/application in marine vehicles and it is not water-proof. The installation should be performed
in a dry compartment with no direct contact with water.
8. Make sure power cable is not short circuited during installation and connection with the battery.
9. Use extreme caution when cutting or drilling the vehicle/vessel panels, checking there are no electrical wiring or structural elements underneath.
10.When positioning the power supply cable, avoid to run the wire over or through sharp edges or close to moving mechanical devices. Use rubber
grommets to protect the wire if it runs in a hole of the plate or proper materials if it is close to heat-generating parts.
11.Make sure all the cables are properly secured all along their length. Also, make sure their outer protective jacket is flame resistant and self
extinguishing. Use a clamping screw to secure positive and negative cables just close to the amplifier respective power supply terminal blocks.
12.Choose the cable gauge according to the amplifier power and to the suggestions you can find here. Use high quality cables, connectors and
accessories, as you can find in the Connection catalogue.
13.Pre-plan the configuration of your new amplifier and the best wiring routes to ease installation.
14.In order to avoid incidental damage, keep the product in the original packaging until you are ready for the final installation.
15.Always wear protective eyewear when using tools, as splints or product residue may become airborne.
TYPICAL INSTALLATION SEQUENCE
If you have any questions please refer to the Advanced Manual you can find available on www.hertzaudiovideo.com or contact your Hertz dealer or
Hertz authorized service for assistance.
1. Before installing the amplifier turn off the source and all other electronic devices in the audio system to prevent any damages.
2. Using a cable with adequate AWG (see chart: Power Supply Cable), run the power wire from the battery location to the amplifier mounting location.
3. Connect the power supply with the correct polarity. connect (+) terminal to the cable coming from the battery and (-) terminal to the vehicle/vessel chassis.
4. Put an insulated fuse holder 40 cm max far from the battery positive terminal; connect one end of the power cable to it after connecting the other
end to the amplifier. Do not mount the fuse.
5. To ground the device (-) in the right way, use a screw in the vehicle/vessel chassis; scrape all paint or grease from the metal if necessary, checking
with a tester that there is continuity between the battery negative terminal (-) and the fixing point. If possible, connect all components to the same
ground point; this solution rejects most noise which can be generated during the audio reproduction.
6. Route all signal cables close together and away from power cables.
7. Connect the RCA input cables, the applied signal must be between 0.2 VRMS and 5 VRMS.
8. Connect the high level inputs using the proper plug. Applied signal must be between 0.8 VRMS and 20 VRMS. Don’t use it if you are already using Pre In
preamplified connection.
9. Connect the speaker output using 10 AWG max speaker cable.
10. Don’t connect (-) L and (-) R speaker outputs together. If you use an external stereo crossover, make sure that its negative poles are not connected together.
11. The amplifier turns on by connecting the remote turn on terminal (REMOTE IN) to the source specific output. The amplifier turns on automatically, without
remote signal, also if using high level inputs (Speaker IN) by setting the “AUTO TURN ON” switch to position ON.
12. The LED on the front panel lights up green indicating that the product is on. The LED lights up red if the outputs go on overload, if the thermal protection
is triggered, if the speaker cables short circuit with the vehicle/vessel chassis and if the amplifier is malfunctioning.
13. The fuse/s is/are located near the power supply and speaker terminals. To replace, remove the fuse/s from the housing. Always replace the fuse of the
same rating.
14.Secure all auxiliary devices you built to install the components to the vehicle/vessel structure; this ensures stability and safety while driving. The
amplifier falling out of its fastening while driving/cruising can seriously damage the people in the vehicle/vessel and other boats.
15.When installation is over, check the system’s wiring and make sure all connections were done in the right way.
16. Put the fuse into the fuse holder. The fuse value will have to be 30% higher than the amplifier built-in one. In case the cable supplies several amplifiers,
the fuse value will have to be 30% higher than the sum of the values of all other fuses in the amplifiers.
17. Listening level calibration is made by adjusting the source volume up to ¾of its maximum level; then, adjust the amplifier levels until you hear distortion.
SAFE SOUND
USE COMMON SENSE AND PRACTICE SAFE SOUND. PLEASE REMEMBER THAT LONG EXPOSURE TO EXCESSIVELY HIGH SOUND PRESSURE LEVELS
MAY DAMAGE YOUR HEARING. SAFETY MUST BE AT THE FOREFRONT WHILE DRIVING.
Information on electrical and electronic equipment waste (for those European countries which organize the separate collection of waste)
Products which are marked with a wheeled bin with an X through it can not be disposed of together with ordinary domestic waste. These electrical and electronic products
must be recycled in proper facilities, capable of managing the disposal of these products and components. In order to know where and how to deliver these products to the
nearest recycling/disposal site please contact your local municipal office. Recycling and disposing of waste in a proper way contributes to the protection of the environment
and to prevent harmful effects on health.
2PRECAUTIONS

35
User’s Manual
Applied power Cable diameter
Connection length
*Current Draw I (A)
Cable Length (m)
1: Power supply cable 2: Speakers cable
B
D
C
E
A
A B C D E
HCP 1MDK 315 291 190 166 50 mm
12.40 11.45 7.48 6.53 1.97 in.
HCP 2MX 315 291 190 166 50 mm
12.40 11.45 7.48 6.53 1.97 in.
HCP 4M
HCP 4MDK
315 291 190 166 50 mm
12.40 11.45 7.48 6.53 1.97 in.
HCP 5MD
HCP 5MD-24V
345 321 190 166 50 mm
13.58 12.64 7.48 6.53 1.97 in.
3INSTALLATION AND SIZES
4CABLE SIZE CALCULATION TABLES:
1: Power supply cable / 2: Speakers cable

36
(Not provided)
Max 20 cm / 7.9 in.
GND REM FUSE+12V
FUSE
POWER - 12V
15 mm / 0.6 in.
8 AWG Max
APPLY A FUSE CLOSE
TO BATTERY POSITIVE POLE
TO PROTECT BATTERY CABLE
REMOTE OUT
SOURCE BATTERY 12 V*
GND
GND
*for HCP 5MD-24V
use 24 V power supply
5POWER SUPPLY and REMOTE IN CONNECTION /FUSE REPLACEMENT
FUSE
REPLACEMENT
WARNING:
Firmly press
contacts of each fuse
intro their
fuse - holder clips
GND REM FUSE+12V
GND REM FUSE+12V GND REM FUSE+12V
GND REM FUSE+12V
GND REM FUSE+12V
GND REM FUSE+12V GND REM FUSE+12V
GND REM FUSE+12V
BATTERY
BATTERY
12 V
12 V
FUSEDHOLDER
FUSEDHOLDER
GND
GND
GND
GND
GND
AMP1
AMP1
AMP2
AMP2
WARNING
MULTIPLE POWER SUPPLY CONNECTION

37
User’s Manual
HCP 5MD
HCP 5MD-24
SUBWOOFER
REMOTE VOLUME CONTROL
6. SUBWOOFER REMOTE VOLUME CONTROL: HRC INSTALLATION
OPTIONAL
OPTIONAL
HRC
HRC
HCP 1MDK
SUBWOOFER
REMOTE VOLUME CONTROL

38
7PRE IN / SPEAKER IN / PRE OUT
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
0°
180°
t
0
PHASE
SUB LEVEL
-40 dB
(Min)
+6 dB
(Max)
SUBSONIC AMP OUT
Hz
25 Hz @ 24 dB/Oct.
25
AMP OUT
Hz
FILTER OFF
500
Hz
LO-PASS @ 24 dB/Oct.
25050
FILTER ON
BOOST
+ 6
0Hz50
dB
LEVELS (INPUT SENSITIVITY)
0.5 V0.2 V
PRE OUT
Hz
HI-PASS @ 12 dB/Oct.
50 250
0°
180°
t
0
PHASE
SUB LEVEL
-40 dB
(Min)
+6 dB
(Max)
SUBSONIC AMP OUT
Hz
25 Hz @ 24 dB/Oct.
25
AMP OUT
Hz
FILTER OFF
500
Hz
LO-PASS @ 24 dB/Oct.
25050
FILTER ON
BOOST
+ 6
0Hz50
dB
LEVELS (INPUT SENSITIVITY)
0.5 V0.2 V
PRE OUT
Hz
HI-PASS @ 12 dB/Oct.
50 250
HI-IN
PRE OUT
PRE IN
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
PRE OUTPUT
SOURCE
HCP 1MDK
HCP 1MDK
R
R
L
L
POWER ON
LED Green
CHECK
LED Red
SUBWOOFER
REMOTE VOLUME
CONTROL (optional)

39
User’s Manual
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
0,25V
LEVELS
Hz
PRE OUT
HI-PASS @ 12 dB/Oct.
50 3,2k Hz
HI-PASS x 1 @ 12 dB/Oct.
50 3,2k
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 3,2k Hz
AMP OUT
LO-PASS @ 12 dB/Oct.
50 3,2k
Hz
PRE OUT
LO-PASS @ 12 dB/Oct.
50 3,2k
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 3,2K
BOOST
+ 6
0Hz50
dB
+3
OFF ON
0,25V
LEVELS
Hz
PRE OUT
HI-PASS @ 12 dB/Oct.
50 3,2k Hz
HI-PASS x 1 @ 12 dB/Oct.
50 3,2k
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 3,2k Hz
AMP OUT
LO-PASS @ 12 dB/Oct.
50 3,2k
Hz
PRE OUT
LO-PASS @ 12 dB/Oct.
50 3,2k
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 3,2K
BOOST
+ 6
0Hz50
dB
+3
OFF ON
HI-IN
PRE OUT
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
PRE OUTPUT
SOURCE
HCP 2MX
R
R
L
L
POWER ON
LED Green
LED Red
CHECK

40
HCP 4M
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
Hz
LO-PASS @ 12 dB/Oct.
50 500
Hz
LO-PASS @ 12 dB/Oct.
50 500
0,25V
FRONT
LEVELS
0,25V
REAR
LEVELS
BOOST
0Hz50
+3
+6
dB
500 Hz
OFF 6dB 12dB
BOOST
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
OFF
OFF
ON
ON
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 3,2k
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 500
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
80 20k
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 500
Hz
LO-PASS @ 12 dB/Oct.
50 500
Hz
LO-PASS @ 12 dB/Oct.
50 500
0,25V
FRONT
LEVELS
0,25V
REAR
LEVELS
BOOST
0Hz50
+3
+6
dB
500 Hz
OFF 6dB 12dB
BOOST
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
OFF
OFF
ON
ON
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 3,2k
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 500
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
80 20k
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
PRE OUT
FULL RANGE
20k Hz
AMP OUT
FULL RANGE
20k Hz Hz
LO-PASS @ 12 dB/Oct.
50 500
HI-IN
FRONT
PRE IN
FRONT
HI-IN
REAR
PRE IN
REAR
PRE OUT
(FRONT CHANNELS)
FOR EACH INPUT
(FRONT - REAR)
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
PRE OUTPUT SOURCE
R
R
L
L
LED Red
CHECK
POWER ON
LED Green

41
User’s Manual
FRONT / REAR PASS MODE
AMP OUT
FULL RANGE
20k Hz
PASS MODE
FULL HI LO
PASS MODE
FULL HI LO
AMP OUT
HI-PASS @ 12 dB/Oct.
Hz50 3,2k
PASS MODE
FULL HI LO
AMP OUT
LO-PASS @ 12 dB/Oct.
Hz50 3,2k
PRE OUT
FULL RANGE
20k Hz
LEVELS (INPUT SENSITIVITY)
0.2 V
(Max)
5 V
(Min)
50 Hz BOOST
+ 12
0 Hz50
dB
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
OFF
OFF
ON
ON
HI-IN
FRONT
PRE IN
FRONT
HI-IN
REAR
PRE IN
REAR
PRE OUT
(FRONT CHANNELS)
FOR EACH INPUT
(FRONT - REAR)
USE PRE-IN
OR HI-IN:
NOT BOTH
HI-LEVEL OUTPUT
PRE OUTPUT SOURCE
R
R
L
L
HCP 4MDK
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
FRONT / REAR PASS MODE
AMP OUT
FULL RANGE
20k Hz
PASS MODE
FULL HI LO
PASS MODE
FULL HI LO
AMP OUT
HI-PASS @ 12 dB/Oct.
Hz50 3,2k
PASS MODE
FULL HI LO
AMP OUT
LO-PASS @ 12 dB/Oct.
Hz50 3,2k
PRE OUT
FULL RANGE
20k Hz
LEVELS (INPUT SENSITIVITY)
0.2 V
(Max)
5 V
(Min)
50 Hz BOOST
+ 12
0 Hz50
dB
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
OFF
OFF
ON
ON
POWER ON
LED Green
LED Red
CHECK

42
HCP 5MD / HCP 5MD-24V
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
Hz
LO-PASS @ 12 dB/Oct.
50 500
0,25V
FRONT
LEVELS
0,25V
REAR
LEVELS
0,25V
SUB
LEVELS BOOST
0Hz50
+12
dB
012dB
Hz500
SUB AMP OUT
FULL RANGE
Hz
SUB AMP OUT
SUBSONIC @ 12 dB/Oct.
25 500
SUBSONIC FILTER
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
80 20k
AMP OUT
FULL RANGE
20k Hz
Hz
LO-PASS @ 12 dB/Oct.
50 5000
BAND
FRONT IN
MODE
HIFULL
BAND
FRONT IN
MODE
HIFULL
BAND
FRONT IN
MODE
HIFULL
Hz
HI-PASS @ 12 dB/Oct.
50 500
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 500
x1
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
5005k
x10
AMP MODE
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
5005k
HI
AMP MODE
PRE OUT
FULL RANGE
20k Hz
FULL
AMP MODE
5 CH
AMP MODE
3 CH
OFFON
If using
REAR INPUT
select
If using
FRONT INPUT only
select
Hz
LO-PASS @ 12 dB/Oct.
50 500
0,25V
FRONT
LEVELS
0,25V
REAR
LEVELS
0,25V
SUB
LEVELS BOOST
0Hz50
+12
dB
012dB
Hz500
SUB AMP OUT
FULL RANGE
Hz
SUB AMP OUT
SUBSONIC @ 12 dB/Oct.
25 500
SUBSONIC FILTER
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
80 20k
AMP OUT
FULL RANGE
20k Hz
Hz
LO-PASS @ 12 dB/Oct.
50 5000
BAND
FRONT IN
MODE
HIFULL
BAND
FRONT IN
MODE
HIFULL
BAND
FRONT IN
MODE
HIFULL
Hz
HI-PASS @ 12 dB/Oct.
50 500
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
50 500
x1
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
5005k
x10
AMP MODE
Hz
AMP OUT
HI-PASS @ 12 dB/Oct.
5005k
HI
AMP MODE
PRE OUT
FULL RANGE
20k Hz
FULL
AMP MODE
5 CH
AMP MODE
3 CH
HI-IN
FRONT
PRE IN
FRONT
HI-IN
REAR
HI-IN
SUB
PRE IN
REAR
FOR EACH INPUT
(FRONT - REAR)
USE PRE-IN
OR HI-IN:
NOT BOTH HI-LEVEL OUTPUT
SUBWOOFER
REMOTE VOLUME
CONTROL
PRE OUTPUT SOURCE
OPTIONAL
R
R
L
L
LED Red
CHECK
POWER ON
LED GrEEn
SUB
INPUT

43
User’s Manual
INPUT
R
L
ON
HCP 2MX
8AUTO TURN ON BY SPEAKER IN (without REMOTE IN)
FUSE
GND REM +12V
30A 30A 30A
FUSE
GND REM +12V
POWER 20A 20A
HCP 1MDK
INPUT
RL
ON
HCP 1MDK

44
HCP5MD
ON
INPUT
R
L
HCP 5MD
HCP 5MD-24V
INPUT
R
L
ON
HCP 4M
HCP 4MDK

45
User’s Manual
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
1CH: FILTERED SUBWOOFER
HCP 1MDK
INPUTS:
OUTPUTS:
FUSE
GND REM +12V
30A 30A 30A
HCP 1MDK
INPUT INPUT
R
R
L
L
ON
SOURCE
USE PRE-IN
OR HI-IN
SUB
LEVEL
SUB
LO PASS
FUSE
GND REM +12V
30A 30A 30A
HCP 1MDK
12 mm / 0.62 in
.
SUBWOOFER
min 2Ω (L+R)
9INSTALLATION EXAMPLES

46
2CH: FRONT L/R
RL
INPUTS:
OUTPUTS:
HCP 2MX
INPUT
INPUT
R
L
SOURCE
USE PRE-IN
OR HI-IN
RL
OFF
FRONT
LEVELS
12 mm / 0.62 in.
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
FULL RANGE SPEAKERS

47
User’s Manual
1CH: SUBWOOFER L+R
INPUTS:
OFF
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
OUTPUTS:
SUBWOOFER
(L+R)
HCP 2MX
INPUT
INPUT
R
L
SOURCE
USE PRE-IN
OR HI-IN
Hi-Pass PRE OUT
to stereo amplifier
RL
SUB
LEVEL
SUB
LO PASS
12 mm / 0.62 in.

48
1CH: SUBWOOFER - MONO INPUT
INPUTS:
ON
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
OUTPUTS:
HCP 2MX
INPUT
AUDIO PROCESSOR
SUBWOOFER CHANNEL
SUB
LEVEL
12 mm / 0.62 in.
SUBWOOFER

49
User’s Manual
Using also REAR INPUTS:
REAR
INPUT
activate
REAR
INPUT
REAR
INPUT
USE PRE-IN OR HI-IN
ON
OUTPUTS:
FRONT REAR
4CH: FRONT + REAR
FRONT
INPUT
FRONT
INPUT
R
R
L
LSOURCE
REAR
LEVELS
USE PRE-IN
OR HI-IN
HI 80
HI 80
OFF
OFF OFF
OFF
INPUTS:
RL
R L
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
HCP 4M
12 mm / 0.62 in.
FULL RANGE SPEAKERS
FRONT
LEVELS

50
Using also REAR INPUTS:
SUB
INPUT
activate
REAR
INPUT
SUB
INPUT
USE PRE-IN OR HI-IN
ON
OUTPUTS:
3CH: FRONT + SUB
FRONT
INPUT
FRONT
INPUT
R
R
L
LSOURCE
USE PRE-IN
OR HI-IN
HI 80OFF
OFF OFF
OFF
INPUTS:
RL
Adjustment
CONTROLS
Not
AVAILABLE :: Set-up
CONTROLS
:
HCP 4M
12 mm / 0.62 in.
SUBWOOFER
(L+R)
SUB
LEVELS LO PASS
FULL RANGE SPEAKERS
FRONT
LEVELS