HidrateSpark STEEL User manual

Quick Start Guide
We’re here to support you.
If you ever need to contact us, here’s how:
Chat with us on our website
hidratespark.com
Email
[email protected]
In App
Settings > Help
For more information and best practices,
please visit hidratespark.com/pages/guide to
review the user manual.
ABC D
DESCRIPTION
REV DATE
HI-004-010
004 Feb. 11, 2020
A. Chug Lid
B. Bottle Body
C. Sensor Puck
D. Charging Cable
GLOW REMINDERS
SUPPORT
• When setting up your bottle you have the choice to
pick your reminder glow color in the Bottles section
of the App.
• Please see hidratespark.com/pages/guide to view all
glow reminders and further information.
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
The FCC requires the user to be notied that any
changes or modications made to this device that are
not expressly approved by HIdrateSpark may void the
user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
The user’s manual or instruction manual for an
intentional or unintentional radiator shall caution the
user that changes or modications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment. In cases where the manual is provided
only in a form other than paper, such as on a computer
disk or over the Internet, the information required by
this section may be included in the manual in that
alternative form, provided the user can reasonably be
expected to have the capability to access information
in that form.
FCC
• DO NOT overload or squeeze the sensor puck as it
can damage internal electronics.
• Your HidrateSpark Steel uses a built-in rechargeable
li-ion battery. Bottle includes a magnetic USB
charging cable for all your charging needs.
• Product is NOT designed for hot liquids. Use only
with cold liquids.
• Not for use with carbonated or pulpy beverages.
• Prior to drinking, make sure the lid is properly
threaded to the body and screwed on completely.
• DO NOT overll. Fill liquids below the threads to avoid
accidental spilling.
• DO NOT microwave or freeze.
• DO NOT use cleaners containing bleach, chlorine,
abrasives and/or harsh chemicals.
• DO NOT continue to use if product is damaged.
• DO NOT carry bottles containing liquid in bags to
help prevent accidental opening.
•Recommended for indoor and ofce use only.
• Recommend recalibration if your bottle encounters a
drop impact.
ATTENTION
This device complies with Innovation, Science and
Economic Development Canada’s licence-exempt
RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
Cet appareil est conforme aux ux RSS exemptés
de licence d’Innovation, Science et Développement
économique Canada. L’opération est soumise aux
deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d’interférence; et
(2) Cet appareil doit accepter toute interférence, y
compris les interférences susceptibles de provoquer
un fonctionnement indésirable de l’appareil.
Radiation Exposure Statement: This equipment
complies with the IC RSS-102 radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20 cm between the radiator and
your body.
Énoncé d’exposition aux rayonnements: Cet
équipement est conforme aux limites d’exposition
aux rayonnements ioniques RSS-102 Pour un
environnement incontrôlé. Cet équipement doit être
installé et utilisé avec un Distance minimale de 20 cm
entre le radiateur et votre corps.
ISEDC

DISASSEMBLING &
ASSEMBLING SENSOR PUCK
• To disassemble puck from body, turn bottle upside
down and unscrew puck counterclockwise from the
body until puck pulls free.
•To assemble puck to the body, turn bottle upside
down and screw in the puck clockwise to the body
until puck snaps into place. Please make sure puck
is fully assembled and secured to the body to ensure
accurate sip readings.
Upon reassembly, we recommend recalibrating
your sensor within the app.
• To charge, turn bottle upside down and remove puck.
•Place puck on at surface and attach the magnetic
end of the HidrateSpark charging cable to the puck.
• While charging your puck will illuminate and FLASH
GREEN.
• Once fully charged your puck will remain SOLID
GREEN.
RECHARGEABLE BATTERY
INSTRUCTIONS
•Before washing, ALWAYS remove sensor puck.
Sensor puck must only be cleaned by using a damp
cloth. NEVER submerge or dishwash sensor puck.
• Wash lid and stainless steel body thoroughly before
rst use.
• RINSE LID & STAINLESS STEEL BODY AFTER EACH
USE with the lid in the open position.
• Lid is Top-Rack Dishwasher Safe.
• The Body is HAND WASH ONLY. To clean the sensor
puck only use a damp cloth. Never submerge or
dishwash the sensor puck.
• ALWAYS STORE BOTTLE WITH THE LID & SENSOR
PUCK REMOVED to allow parts to dry completely.
Upon reassembly, we recommend recalibrating
your sensor within the app.
CLEANING INSTRUCTIONSDOWNLOAD THE APP
• Download our free HidrateSpark Smart Water Bottle
App from the App Store or on Google Play.
• Check that you have an internet connection and your
Bluetooth is turned on. Follow the steps in the app to
create an account, set parameters for a personalized
hydration goal, add your bottle to your prole, and set
your push notications and glow reminders.
• Set down your bottle after every rell and drink.
Remember to sync the app near the bottle each day
so your water is tracked correctly.