HidrateSpark Pro User manual

• DO NOT overload or squeeze the sensor puck as it
can damage internal electronics.
• Your HidrateSpark uses a magnetic USB charging
cable for all your charging needs
• The Chug lid and Straw lid, are ONLY designed for
cold liquids.
• Not for use with carbonated or pulpy beverages.
• Prior to drinking make sure the lid is properly
threaded to the body and screwed on completely or
pressed down completely to the body
• DO NOT overll. Fill liquids below the threads to avoid
accidental spilling.
• DO NOT microwave or freeze.
• DO NOT use cleaners containing bleach, chlorine,
abrasives and/or harsh chemicals.
• DO NOT continue to use if product is damaged.
• DO NOT carry bottles containing liquid in bags to
help prevent accidental opening.
• Recommend recalibration if your bottle encounters a
drop impact.
Quick Start Guide
DESCRIPTION
REV DATE
HI-PRO-EPKG-01
002 11 / 23 / 2021
ATTENTION
WORLD’S SMARTEST
WATER BOTTLE
We’re here to support you.
If you ever need to contact us, here’s how:
Chat with us on our website
hidratespark.com
Email
suppor[email protected]
In App
Help
For more information and best practices,
please visit hidratespark.com/pages/guide
to review the user manual.
SUPPORT
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
The FCC requires the user to be notied that any changes
or modications made to this device that are not expressly
approved by HIdrateSpark may void the user’s authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
FCC
This device complies with Innovation, Science and Economic
Development Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Cet appareil est conforme aux ux RSS exemptés de licence
d’Innovation, Science et Développement économique Canada.
L’opération est soumise aux deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer d’interférence; et
(2) Cet appareil doit accepter toute interférence, y compris les
interférences susceptibles de provoquer un fonctionnement
indésirable de l’appareil.
ISEDC
CAUTION
The ambient temperature range of sensorpuck is: -20°C-60°C
In order to maintain compliance with FCC regulations, shielded
cables must be used with this equipment. Operation with non-
approved equipment or unshielded cables is likely to result in
interference to radio and TV reception.
Manufacturer: Hidrate, Inc.
Address: 1400 Van Buren St NE, Suite 135, Minneapolis, MN
55413 USA
Frequency band: 2402-2480 MHz; Maximum radio-frequency
power: 4dBm

DISASSEMBLING &
ASSEMBLING SENSOR PUCK
• To disassemble puck from body, turn bottle upside
down and unscrew puck counterclockwise from the
body until puck pulls free.
• To assemble puck to the body, turn bottle upside
down and screw in the puck clockwise to the body
until puck snaps into place. Please make sure puck
is fully assembled and secured to the body to ensure
accurate sip readings.
Upon reassembly, we recommend recalibrating
your sensor within the app.
• To charge, turn bottle upside down and remove puck.
• Place puck on at surface and attach the magnetic
end of the HidrateSpark charging cable to the puck.
• While charging your puck will illuminate and FLASH
GREEN.
• Once fully charged your puck will remain SOLID
GREEN.
RECHARGEABLE BATTERY
INSTRUCTIONS
• Before washing, ALWAYS remove sensor puck.
Sensor puck must only be cleaned by using a damp
cloth. NEVER submerge or dishwash sensor puck.
• Wash lid and body thoroughly before rst use.
• RINSE LID & BODY AFTER EACH USE with the lid in
the open position.
• Lids and Tritan plastic body are top-rack dishwasher
safe.
• The Stainless Steel Body is HAND WASH ONLY. To
clean the sensor puck only use a damp cloth. Never
submerge or dishwash the sensor puck.
• ALWAYS STORE BOTTLE WITH THE LID & SENSOR
PUCK REMOVED to allow parts to dry completely.
Upon reassembly, we recommend recalibrating
your sensor within the app.
CLEANING INSTRUCTIONS
DOWNLOAD THE APP
• Download our free HidrateSpark App from the App
Store or on Google Play.
• Check that you have an internet connection and your
Bluetooth is turned on. Follow the steps in the app to
create an account, set parameters for a personalized
hydration goal, add your bottle to your prole, and set
your push notications and glow reminders.
• Set down your bottle on a at surface after every rell
and drink. Remember to sync the app near the bottle
each day so your water is tracked correctly.
GLOW REMINDERS
• When setting up your bottle, you have the choice to
pick your reminder glow color in the Bottles tab of
the App. Use the color palette button located in your
bottle’s card to choose your glow reminder color.
• Please see hidratespark.com/pages/guide to view all
glow reminders and further information.