NRS Healthcare Rise Easy G21808 User manual

User Instructions
Rise Easy Bed Aid
G21808 –Single 762mm (30”) to 1220mm (48”)
G21819 –Double1372mm (54”) to 1525mm (60”)
Intended Use
The Rise Easy Bed Aid is designed to assist
the user in rising from, or sitting up in bed,
without interfering with bed clothes. It is
available in two sizes and is suitable for most
beds including profiling beds. It can be used
on either the left or right hand side of the bed.
Safety Precautions
Do not place obstructions (for example a
bedside cabinet) adjacent to the bed rail. It is
important that the arm is free to be moved
away from the bed.
Do not use if feet of bed are too large to fit
onto base plate pads.
It is recommended that this device is only
used for clients up to 127Kg (20st).
MANUAL HANDLING GUIDANCE
During installation, it is necessary to lift the
bed head onto the bed rail base plates.
Please ensure that the person(s) installing the
device is capable of doing this operation
safely using the correct manual handling
techniques and employ caution when lifting
the bed.
Diagram 1
Assembly & Installation Instructions
1 - Remove all parts from the packaging.
Check all parts are undamaged.
2 –Ensuring there are no obstructions
(E.g. Bed side cabinet) on the side which the
client will exit the bed; move the bed
approximately 300mm (12”) from the wall
3. –Place the 2 base plate sections on the
floor and push both silver coloured connecting
rods into both tubes on base plates to the bed size
required. Note: DO NOT PULL TUBE PAST THE
WARNING DIMPLES
4 - Slide assembly behind the head section of
the bed and align base plates to bed
castors/feet.
5 - Lift the bed and slide assembly under the
castors/feet of the bed. Lower bed onto the
base plate ensuring the castors/feet sit onto
the base plate. Carefully move the bed/Base
plate assembly back to the wall.
6 –The hand rail may now be fitted on the
appropriate side of the bed. Slide the handrail
over the location tube and push down until it
hits the location stop pin.
7. Check that the bed rail feels secure and
can be swung away from the bed.
General Safety Warning
Please ensure these instructions are
fully read and implemented. Failure to
do so may result in injury to the user.
Retain in a safe place for future
reference.
Maximum
User Weight

This product is from a range of over 3000
daily living aids available from NRS
Healthcare.
To view the full range please visit our website
or contact us, Tel: [phone]
Manufactured in the UK for
NRS Healthcare,
Sherwood House,
Cartwright Way,
Forest Business Park,
Bardon Hill,
Coalville,
Leicestershire,
LE67 1UB,
United Kingdom.
Tel. Head Office: 0330 100 0098
Tel. Customer Services: 0345 121 8111
Email: [email protected]
UI/G21808/G21819/0616/3
www.nrshealthcare.co.uk
Cleaning Instructions
Clean regularly, wipe with a mild
detergent/ disinfectant solution.
Do not use abrasive cleaners or cloths on
this product.
Using the Rise Easy Bed Aid
The Rise Easy Bed aid is designed such
that the weight of the bed and client, applied
on to the base plates, counterbalances the
client during standing.
As it does not attach to the bed frame, it can
be used on Divan beds (including sprung
base), slatted beds and profiling/electrically
adjustable beds provided the feet or castors
can be fitted onto the base plate pads
(within the sizes indicated; up to 5ft).
The normal “rest” position for the hand rail is
shown in Fig 1, with the hand rail adjacent to
the bed side. In this position, the bed rail
may be used to assist the client to rise from
lying to sitting and to aid repositioning in the
bed e.g. turning. Please note: it is not
intended to act as a cot-side to prevent the
client from falling out of bed.
When standing from the bed, the hand rail
can be left in the “rest” position against the
bed, or swung out away from the bed as
shown in Fig 2 and Fig 3, depending on the
preferences of the client. When in the “swing
away” position, the client should try to place
their weight vertically down through the hand
rail.
Fig 1
Fig 2
Fig 3