Highendled YHLL-001TZ 4IN1 LED Par User manual

1 of 7 pages
Operation Manual
HIGHENDLED YHLL-001TZ-5W 4 in 1 RGBW LED PAR ZOOM
The YHLL-001TZ 4IN1 LED Par can creates a bright array of colors for dynamic stage lighting and scenery
effects. It is widely used in entertainment halls, theaters, clubs. church auditoriums, live stages, etc. The LED
menu is operated via four buttons - MODE, SET UP,UP, & DOWN. The YHLL-001Z 4IN1 has integrated
temperature protection, allowing the light to automatically shut off should the light reach temperatures above
85˚C (181˚F). This allows the unit to cool off in extreme temperatures without damage and while not affecting
other units in operation.The fan speed will be adjusted automatically with the temperature of the LED PAR,the
higher the faster.
Specifications
•Size:37x27x22CM
•Weight: 6.2kgs
•Power input: AC120V/240V 50HZ/60HZ
•Wattage: 125W
•LEDS: 24PCS 5W (4 IN 1)
•Beam angle of LEDs: 25°~60°
•3PIN female DMX XLR socket and 3PIN male DMX XLR socket
•Built-in microphone
•4 button Digital LED menu

2 of 7 pages
Operating Modes
•DMX mode
•Manual dimmer color mode
•Static color select mode
•Auto-run program mode (Continued Color Change&Color Mixing)
•Sound-active mode
•Other mode
Mode Selection
Here above six kinds running mode are selected by MODE button.The DP dot of fourth digital tube will be
flicker when you operate it ,then the DP dot will be automatically off after 60 seconds if there is no
operation.The four digital tube will display the current operation mode.You have to press the MODE button if
you want to operate the LED PAR again.
MODE
manual
SET UP manual UP/DOWN manual instruction
Address ~ Sets the DMX starting address
The unit occupies 5 DMX channels
The unit occupies 6 DMX channels
The unit occupies 7 DMX channels
Channels
The unit occupies 8 DMX channels
Zoom direction up:the bigger DMX value,the
bigger beam angle
DMX
MODE
Zoom direction
Zoom direction down:the bigger DMX
value,the smaller beam angle
Red dimmer ~ Adjust the intensity of the red color
Green dimmer ~ Adjust the intensity of the green color
Blue dimmer ~ Adjust the intensity of the blue color
White dimmer ~ Adjust the intensity of the white color
Strobe ~ Adjust the strobe speed, is flash
off, is slowest, is fastest
DIMMER
MODE
Zoom ~ Adjust the beam angle from big to small
Sound Mode select ~ Select the built-in sound mode
Sensitivity select ~ Adjust the sensitivity of the
sound-active, is the lowest
level, is the highest level
SOUND
MODE
Zoom ~ Adjust the beam angle from big to small
Dreaming mode set ~ Select the built-in dreaming mode

3 of 7 pages
Jumping mode set ~ Select the built-in jumping mode
Speed set ~ Adjust the speed of the dreaming/snap
program mode
AUTO
RUN
MODE
Zoom ~ Adjust the beam angle from big to small
Static Color select ~ Select the 15 static colors
Strobe ~ Adjust the strobe speed, is flash
off, is slowest, is fastest
STATIC
COLOR
SELECT
MODE Zoom ~ Adjust the beam angle from big to small
LED digital tube display always onDisplay
on/off LED digital tube display off
LED digital tube display normalDisplay
normal/inversed LED digital tube display inversed
Initialization
mode
Initialize the unit at the extra factory setting
OTHER
MODE
Reset mode Reset the position of the electric machine
Manual Dimmer Color Mode
1. Press MODE button until you select red dimmer color r(XXX). Continue pressing the SET UP to
choose different color,green G(XXX), blue b(XXX) or white u(XXX).Then continue pressing the SET
UP to select strobe mode FS(XX) and the zoom mode Z.(XXX).
2. Press UP or DOWN to adjust the intensity of the red,green,blue or the white color 0-255 ,the speed of
the strobe in the strobe mode and the beam angle from big to small.
0-Off Strobe 1-Lowest Speed 15-Highest Speed
Static Color Select Mode
1. Press MODE button until you select CL(XX). Then continue pressing the SET UP to select strobe
mode St(XX) and the zoom mode Z.(XXX).
2. Press UP or DOWN to select static color 0-15 ,the strobe speed in the strobe mode and the beam
angle from big to small.
0-Off Strobe 1-Lowest Speed 15-Highest Speed
Auto-Run Program Mode
Two Auto-Run styles are built into the YHLL-001Z 4 in 1– Continued Color change program(AJ-X), Color
Mixing (AF-X).
1. Press “MODE ” button until you select AJ-(X) .Continue pressing SET UP to choose Color Mixing
AF-(X),and continue pressing SET UP to reach the SP(XX)Auto-run Speed Set Mode and the zoom
Mode Z.(XXX).
2. Press UP or DOWN to select the built-in AJ-(X) Continued Color change program 1-8 ,the built-in

4 of 7 pages
AF-(X) Color Mixing Modes 1-8,the Color change program Modes&Color Mixing Modes speed SP(XX) 1-16
and the beam angle from big to small.
1-Lowest Speed 16-Highest Speed
Sound-Active Mode
1. Press MODE button until you select SO-(X).Press UP or DOWN to select the Sound-Active Mode
1-8.
2. Continue pressing SET UP button to select SJ-(X).Press UP or DOWN to select the Audio
Sensitivity 1-8.
1-Off Sound-Active 2-Lowest Sensitivity 8-Highest Sensitivity
3. Continue pressing SET UPbutton to select Z.(XXX).Press UP or DOWN to the beam angle from big
to small.
0-the biggest beam angle 190-the smallest beam angle
Other Mode
Three styles are built into the YHLL-001Z 4 in 1–Display on/off mode,Display normal/inversion
mode,Initialization mode,reset mode.
1. Display on/off mode:Press MODE button until you select "don".Press UP or DOWN to select
display always on "don" or the display off "doFF"
2. Display normal/inversion mode:Continue pressing SET UP button until you select"Stnd".Press UP or
DOWN button to select display normal"Stnd" or display inversion"evr".
3. Initialization mode:Continue pressing SET UP button until you select"dEFA".Now press UP and
DOWN at the same time,you can initialize it at extra factory setting,running on the the first color change
program mode,and the four digital tube displays"AJ-1".
4. Reset mode:Continue pressing SET UP button until you select"rESt".Now press UP and
DOWN at the same time,the electric machine will reset automatically to make sure that it will be in the
right position.
DMX mode
You can control the devices individually via your DMX controller. The YHLL-001Z 4 in 1 is in slave mode in
any situation of DMX mode when it is combined to other YHLL-001Z 4 in 1, but not with a DMX-controller.
Addressing
The DMX control board allows you to assign the DMX address which is defined as the first channel
from which the YHLL-001Z will respond to from the controller.
1. Press MODE button until the display reads A.XXX
2. Press UP or DOWN to set the DMX address.
You can set 508 pcs. at most when the YHLL-001Z it is in 5 channels DMX mode,507 pcs. at most
when it is in 6 channels DMX mode,506 pcs at most when it is in 7 channels DMX mode,505 pcs at
most when it is in 8 channels DMX mode.The LED display will flicker when there is no controller

5 of 7 pages
signal.
Zoom direction
1. Press MODE button until the display reads A.XXX,then press SET UP button to reach"Zd.UP".
2. Press UP or DOWN to select zoom direction up"Zd.UP" or zoom direction
down"Zd.dn"."Zd.UP"means that the bigger DMX value,the bigger beam angle;"Zd.dn"means that the
bigger DMX value,the smaller beam angle.
DMX-PROTOCOL
The YHLL-001Z can be controlled using 5, 6 ,7 or 8 channels. The DMX address chart is on the
following pages.
Five Channels controls Red, Green,Blue ,White and Zoom.
Six channels controls Red, Green, Blue, White ,Master Dimmer and Zoom.
Seven channels control Red, Green, Blue, White,Master Dimmer, Strobe and Zoom.
Eight channels control Red, Green, Blue, White,Master Dimmer, Strobe macro (auto-effects) and
Zoom.
1. Press MODE button until the display reads CH0(X)
2. Press UP or DOWN to set the number of desired DMX channels (5,6,7,8)
5 Channel Configuration
CH No.
DMX
value
Function
CH1 000~255 Red(dim→bright)
CH2 000~255 Green(dim→bright)
CH3 000~255 Blue(dim→bright)
CH4 000~255 White(dim→bright)
Zoom,adjust the beam angle from the smallest to biggest when it is set to
CH5 000~255
Zoom,adjust the beam angle from the biggest to smallest when it is set to
6 Channel Configuration
CH
No.
DMX
value
Function
CH1 000~255 Red(dim→bright)
CH2 000~255 Green(dim→bright)
CH3 000~255 Blue(dim→bright)
CH4 000~255 White(dim→bright)
CH5 000~255 Dimming(dim→bright)
Zoom,adjust the beam angle from the smallest to biggest when it is set to
CH6 000~255
Zoom,adjust the beam angle from the biggest to smallest when it is set to

6 of 7 pages
7 Channel Configuration
CH
No.
DMX
value
Function
CH1 000~255 Red(dim→bright)
CH2 000~255 Green(dim→bright)
CH3 000~255 Blue(dim→bright)
CH4 000~255 White(dim→bright)
CH5 000~255 Dimming(dim→bright)
000~015 No function
CH6 016~255 Strobe slowest to fastest flash frequency is 0.1HZ-20HZ
Zoom,adjust the beam angle from the smallest to biggest when it is set to
CH7 000~255
Zoom,adjust the beam angle from the biggest to smallest when it is set to
8 Channel Configuration
CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1
MODE
DMX
VALUE
FUNCTION
1 0-15 No function
White
0-255
(dim→
bright)
Blue
0-255
(dim→
bright)
Green
0-255
(dim→
bright)
Red
0-255
(dim→
bright)
2 16-31 Red
3 32-47 Green
4 48-63 Blue
5 64-79 Purple
6 80-95 Yellow
7 96-111 Cyan
8 112-127 White
Strobe
slowest to
fastest
16-255
flash
frequency is
0.1HZ-20HZ
9 128-135 Color mixing 1
10 136-143 Color mixing 2
11 144-151 Color mixing 3
12 152-159 Color mixing 4
13 160-167 Color mixing 5
14 168-175 Color mixing 6
15 176-183 Color mixing 7
Zoom
1.adjust the
beam angle
from the
smallest to
biggest when
it is set
to
2.adjust the
beam angle
from the
biggest to
smallest
when it is set
to
16 184-191 Color mixing 8
Speed
0-255
(slow→
quick)
Dimming
0-255
(dim→
bright)
N
o
function
N
o
function
N
o
function
N
o
function

7 of 7 pages
17 192-199 Color change 1
18 200-207 Color change 2
19 208-215 Color change 3
20 216-223 Color change 4
21 224-231 Color change 5
22 232-239 Color change 6
23 240-247 Sound mode1
24 248-255 Sound mode2
Sensitivity
0-255