HIK VISION ColorVu DS-2CE DFT-F Series User manual

2 MP
Bullet and Turret
Cameras
User Manual
122919NA
DS-2CE10DFT-F • DS-2CE10DFT-F28
DS-2CE12DFT-F • DS-2CE12DFT-F28
DS-2CE72DFT-F •DS-2CE72DFT-F28
olo
r
V
u

UM ColorVu DS-2CExxDFT-Fxx 122919NA 2
Table of Con en s
Regula ory Informa ion ...................................................................... 3
FCC Informa ion ................................................................................... 3
FCC Condi ions .................................................................................... 3
EU Conformi y S a emen .................................................................. 3
Indus ry Canada ICES-003 Compliance ............................................ 4
Warning ................................................................................................ 4
Safe y Ins ruc ion ............................................................................... 4
Warnings .............................................................................................. 4
Cau ions ............................................................................................... 5
Mark Descrip ion ................................................................................. 5
1 In roduc ion ................................................................................... 6
Produc Fea ures ................................................................................ 6
• High Performance CMOS Sensor .................................................. 6
• Full Time Color ............................................................................... 6
• OSD Menu wi h Configurable Parame ers ................................... 6
• Au o Whi e Balance ...................................................................... 6
• In ernal Synchroniza ion .............................................................. 6
• Smar Ligh Mode .......................................................................... 6
• 3-Axis Adjus men ......................................................................... 6
Overview............................................................................................... 6
1.1 Overview of Type I Bulle Camera .............................................. 6
1.2 Overview of Type II Bulle Camera ............................................. 6
1.3 Overview of Type I Turre Camera ............................................. 7
2 Ins alla ion ..................................................................................... 7
2.1 Ins alla ion of Type I Bulle Camera ......................................... 7
2.1.1 Ceiling/Wall Moun ing wi hou Junc ion Box ....................... 7
2.1.2 Ceiling/Wall Moun ing wi h Junc ion Box ............................. 9
2.2 Ins alla ion of Type II Bulle Camera ...................................... 10
2.2.1 Ceiling/Wall Moun ing wi hou Junc ion Box ..................... 10
2.2.2 Ceiling/Wall Moun ing wi h Junc ion Box ........................... 11
2.3 Ins alla ion of Type I Turre Camera ....................................... 12
2.3.1 Ceiling/Wall Moun ing wi hou Junc ion Box ..................... 12
2.3.2 Ceiling/Wall Moun ing wi h Junc ion Box ........................... 14
3 Menu Descrip ion ........................................................................ 16
3.1 FORMAT ....................................................................................... 17
3.2 EXPOSURE ................................................................................... 17
3.1.1 EXPOSURE MODE ....................................................................... 17
• GLOBAL .......................................................................................... 17
• BLC (Backligh Compensa ion) .................................................. 17
• WDR (Wide Dynamic Range) ....................................................... 17
3.1.2 AGC (Au o Gain Con rol) ......................................................... 17
3.1.3 SLOW SHUTTER ........................................................................ 17
3.1.4 VIDEO SETTINGS ....................................................................... 18
• WHITE BALANCE ............................................................................ 18
• BRIGHTNESS .................................................................................. 18
• CONTRAST...................................................................................... 18
• SHARPNESS ................................................................................... 18
• SATURATION .................................................................................. 19
• 3 DNR (Digi al Noise Reduc ion) ................................................. 19
• MIRROR .......................................................................................... 19
3.1.5 SMART LIGHT ............................................................................. 19
• AUTO .............................................................................................. 19
• OFF ................................................................................................ 19
3.1.6 FUNCTIONS ................................................................................ 19
• PRIVACY ......................................................................................... 19
• MOTION .......................................................................................... 20
• DPC (Defec ive Pixel Correc ion) ................................................ 20
3.1.7 FACTORY DEFAULT .................................................................... 20
3.1.8 SAVE & EXIT............................................................................... 20

UM ColorVu DS-2CExxDFT-Fxx 122919NA 3
User Manual
Thank you for purchasing our produc . If here are any
ques ions or reques s, do no hesi a e o con ac he
dealer.
This manual applies o he models below:
Type Model
Type I Bullet Camera
DS
-
2CE10DFT
-
F
DS
-
2CE10DFT
-
F
28
Type II Bullet Camera
DS
-
2CE12DFT
-
F
DS
-
2CE12DFT
-
F
28
Type I Turret Camera
DS
-
2CE72DFT
-
F
DS
-
2CE72DFT
-
F28
This manual may con ain several echnical mis akes or
prin ing errors, and he con en is subjec o change
wi hou no ice. The upda es will be added o he new
version of his manual. We will readily improve or upda e
he produc s or procedures described in he manual.
Regulatory Information
FCC Information
Please ake a en ion ha changes or modifica ion no
expressly approved by he par y responsible for
compliance could void he user’s au hori y o opera e
he equipmen .
FCC Compliance
This equipmen has been es ed and found o comply
wi h he limi s for a Class A digi al device, pursuan o
par 15 of he FCC Rules. These limi s are designed o
provide reasonable pro ec ion agains harmful
in erference when he equipmen is opera ed in a
commercial environmen . This equipmen genera es,
uses, and can radia e radio frequency energy and, if no
ins alled and used in accordance wi h he ins ruc ion
manual, may cause harmful in erference o radio
communica ions. Opera ion of his equipmen in a
residen ial area is likely o cause harmful in erference in
which case he user will be required o correc he
in erference a his own expense.
FCC Conditions
This device complies wi h par 15 of he FCC Rules.
Opera ion is subjec o he following wo condi ions:
1. This device may no cause harmful in erference.
2. This device mus accep any in erference received,
including in erference ha may cause undesired
opera ion.
EU Conformity Statement
This produc and, if applicable, he supplied
accessories oo are marked wi h “CE” and
comply herefore wi h he applicable

UM ColorVu DS-2CExxDFT-Fxx 122919NA 4
harmonized European s andards lis ed under he Low
Vol age Direc ive 2014/35/EU, he EMC Direc ive
2014/30/EU, he RoHS Direc ive 2011/65/EU.
20 2/ 9/EU (WEEE Directive): Produc s marked
wi h his symbol canno be disposed of as
unsor ed municipal was e in he European Union.
For proper recycling, re urn his produc o your
local supplier upon he purchase of equivalen new
equipmen , or dispose of i a designa ed collec ion
poin s. For more informa ion see: www.recycle his.info.
2006/66/EC (Battery Directive): This produc
con ains a ba ery ha canno be disposed of
as unsor ed municipal was e in he European
Union. See he produc documen a ion for
specific ba ery informa ion. The ba ery is marked wi h
his symbol, which may include le ering o indica e
cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, re urn he ba ery o your supplier or o a
designa ed collec ion poin . For more informa ion, see:
www.recycle his.info.
Industry Canada ICES-003 Compliance
This device mee s he CAN ICES-3 (A)/NMB-3(A)
s andards requiremen s.
Warning
This is a class A produc . In a domes ic environmen his
produc may cause radio in erference, in which case he
user may be required o ake adequa e measures.
Safety Instruction
These ins ruc ions are in ended o ensure ha user can
use he produc correc ly o avoid danger or proper y
loss.
The precau ion measure is divided in o “Warnings” and
“Cau ions.”
Warnings: Serious injury or dea h may occur if any of he
warnings are neglec ed.
Cautions: Injury or equipmen damage may occur if any
of he cau ions are neglec ed.
Warnings
Follow
hese
safeguards o preven
serious injury or dea h.
Cautions
Follow hese
precau ions o preven
po en ial injury or ma erial
damage.
Warnings
In he use of he device, you mus be in s ric
compliance wi h he elec rical safe y regula ions of he
na ion and region.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 5
Inpu vol age should mee bo h he SELV (Safe y Ex ra
Low Vol age) and he Limi ed Power Source wi h 12 VDC
according o he IEC60950-1 s andard. Refer o
echnical specifica ions for de ailed informa ion.
Do no connec mul iple devices o one power adap er
o avoid overhea ing or a fire hazard caused by overload.
Make sure ha he plug is firmly connec ed o he power
socke .
Make sure ha he device is firmly fixed if wall moun ing
or ceiling moun ing is used.
If smoke, odor, or noise rise from he device, urn off he
power a once, unplug he power cord, and con ac he
service cen er.
Never a emp o have he camera disassembled by
unprofessional personnel.
Cautions
Do no drop he camera or subjec i o physical shock.
Do no ouch sensor modules wi h fingers.
Do no place he camera in ex remely ho , cold ( he
opera ing empera ure shall be -40° o 60° C), dus y, or
damp loca ions, and do no expose i o high
elec romagne ic radia ion.
If cleaning is necessary, use a clean clo h wi h a bi of
e hanol, and wipe i gen ly.
Do no aim he camera a he sun or ex ra brigh places.
The sensor may burn ou by a laser beam, so if any laser
equipmen is in use, make sure ha he surface of he
sensor will no be exposed o he laser beam.
Do no expose he device o high elec romagne ic
radia ion or an ex remely ho , cold, dus y, or damp
environmen .
To avoid hea accumula ion, good ven ila ion is required
for he opera ing environmen .
Keep he camera away from liquid while in use for a non-
wa erproof device.
While in delivery, he camera shall be packed in i s
original, or similar, packing.
Mark Description
Table 0-1 Mark Descrip ion
Mark Description
DC Vol age

UM ColorVu DS-2CExxDFT-Fxx 122919NA 6
Introduction
Product Features
The main fea ures are as follows:
• High Performance CMOS Sensor
• Full Time Color
• OSD Menu with Configurable Parameters
• Auto White Balance
• Internal Synchronization
• Smart Light Mode
• 3-Axis Adjustment
2Overview
This manual applies o wo ypes of bulle camera and
one ype of urre camera. The overviews of each ype
are shown in he figures below.
. Overview of Type I Bullet Camera
Figure 1, Type I Bulle Camera Overview
NOTE: Press and hold he swi ch bu on for five
seconds o swi ch he video ou pu . Four
kinds of video ou pu s are available: TVI, AHD,
CVI, and CVBS.
.2 Overview of Type II Bullet Camera
Figure 2, Type II Bulle Camera Overview
NOTE: Press and hold he swi ch bu on for five
seconds o swi ch he video ou pu . Four
kinds of video ou pu s are available: TVI, AHD,
CVI, and CVBS.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 7
.3 Overview of Type I Turret Camera
Figure 3, Type I Turre Camera Overview
NOTE: Press and hold he swi ch bu on for five
seconds o swi ch he video ou pu . Four
kinds of video ou pu s are available: TVI, AHD,
CVI, and CVBS.
3Installation
Before You Start
Make sure ha he device in he package is in good
condi ion and all he assembly par s are included.
Make sure ha all he rela ed equipmen is powered off
during he ins alla ion.
Check he specifica ion of he produc s for he
ins alla ion environmen .
Check whe her he power supply ma ches your power
ou pu o avoid damage.
Make sure he wall is s rong enough o wi hs and hree
imes he weigh of he camera and he moun .
If he wall is concre e, inser expansion bol s before
ins alling he camera. If he wall is wood, use self-
apping screws o secure he camera.
If he produc does no func ion properly, con ac your
dealer or he neares service cen er. Do NOT disassemble
he camera for repair or main enance yourself.
2. Installation of Type I Bullet Camera
2. . Ceiling/Wall Mounting without Junction Box
1. Pas e he drill empla e (supplied) where you wan o
ins all he camera.
2. Drill he screw holes and he cable hole (op ional) in
he ceiling/wall according o he drill empla e.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 8
Figure 2-1 Drill Templa e
NOTE: Drill he cable hole when using he ceiling
ou le o rou e he cable.
3. A ach he bracke o he ceiling/wall, and secure he
camera wi h supplied screws.
Figure 2-2 Affix Camera o Ceiling
NOTE: The supplied screw package con ains self-
apping screws and expansion bol s.
For a concre e wall/ceiling, expansion bol s are
required o affix he camera. For a wood wall/ceiling,
self- apping screws are required.
4. Rou e he cables hrough he cable hole or he side
opening.
5. Connec he corresponding power cord and video
cable.
6. Power on he camera o check whe her he image on
he moni or is a an op imum angle. If no , adjus he
camera according o he figure below o ge an
op imum angle.
Figure 4, 3-Axis Adjus men

UM ColorVu DS-2CExxDFT-Fxx 122919NA 9
1) Loosen he P screw o adjus he pan posi ion [0°
o 360°]. Tigh en he screw af er comple ing he
adjus men .
2) Loosen he T screw o adjus he il posi ion [0°
o 180°]. Tigh en he screw af er comple ing he
adjus men .
3) Loosen he R screw and ro a e he camera [0° o
360°]. Tigh en he screw af er comple ing he
adjus men .
2. .2 Ceiling/Wall Mounting with Junction Box
Before You Start
You need o purchase a junc ion box separa ely.
1. Pas e he drill empla e on he ceiling/wall.
Figure 5, Junc ion Box Drill Templa e
2. Drill screw holes and he cable hole in he
ceiling/wall according o he drill empla e holes.
3. Take apar he junc ion box, and align he bulle
camera screw holes wi h hose on he junc ion box
cover.
Figure 6, A ach Camera o Junc ion Box Cover
4. A ach he camera on he junc ion box’s cover wi h
supplied screws.
5. A ach he junc ion box body o he ceiling/wall by
aligning he screw holes of he junc ion box.
6. Secure he junc ion box’s body wi h supplied screws
on he ceiling/wall.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 10
Figure 7, Affix Junc ion Box o Wall/Ceiling
7. Rou e he cables hrough he bo om cable hole or
he side cable hole of he junc ion box.
Figure 8, Rea ach Cover o Junc ion Box
8. Connec he junc ion box cover o i s body.
9. Repea s eps 5 and 6 of 2.1.1 Ceiling/Wall Moun ing
wi hou Junc ion Box
o comple e he ins alla ion.
2.2 Installation of Type II Bullet Camera
2.2. Ceiling/Wall Mounting without Junction Box
1. Pas e he drill empla e (supplied) where you wan o
ins all he camera.
2. Drill he screw holes according o he drill empla e
and he cable hole (op ional) on he ceiling.
Figure 9, Drill Templa e
NOTE: Drill he cable hole in cen er of drill empla e
when using ceiling ou le o rou e he cable.
3. Rou e he cables hrough he cable hole (op ional) or
he side opening.
Body
Junction Box

UM ColorVu DS-2CExxDFT-Fxx 122919NA 11
4. Fix he camera o he ceiling wi h supplied screws.
Figure 10, Affix Camera o Ceiling
NOTE: The supplied screw package con ains self-
apping screws and expansion bol s.
5. For a concre e wall/ceiling, expansion bol s are
required o fix he camera. For a wood wall/ceiling,
self- apping screws are required.
6. Connec he corresponding power cord and video
cable.
7. Power on he camera o check whe her he image on
he moni or is a an op imum angle. If no , adjus he
surveillance angle.
Figure 11, 3-Axis Adjus men
1) Loosen he No.1 adjus ing screw o adjus he
pan posi ion [0° o 360°]. Tigh en he No.1
adjus ing screw.
2) Loosen he No.2 adjus ing screw o adjus he
il ing posi ion [0° o 180°]. Tigh en he No. 2
adjus ing screw.
3) Loosen he No.3 adjus ing screw o adjus he
ro a ion posi ion [0° o 360°]. Tigh en he No.3
adjus ing screw.
2.2.2 Ceiling/Wall Mounting with Junction Box
Before You Start
You need o purchase a junc ion box separa ely.
1. Pas e he drill empla e on he ceiling/wall.
2. Drill screw holes and he cable hole (op ional) in he
ceiling/wall according o he drill empla e holes.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 12
Figure 12, Drill Templa e
NOTE: Drill he cable hole when using ceiling ou le
o rou e he cable.
3. Take apar he junc ion box, and align he screw holes
of he bulle camera wi h hose on he junc ion box’s
cover.
4. Fix he camera on he junc ion box’s cover wi h hree
supplied screws.
Figure 13, Ins all he Junc ion Box
5. Secure he junc ion box’s body wi h supplied screws
on he ceiling/wall.
6. Rou e he cables hrough he bo om cable hole or
he side cable hole of he junc ion box.
Figure 14, A ach Junc ion Box Cover o i s Body
7. A ach he junc ion box cover o i s body wi h
supplied screws.
8. Repea s eps 5 and 6 of 2.2.1 Ceiling/Wall Moun ing
wi hou Junc ion Box
o comple e he ins alla ion.
2.3 Installation of Type I Turret Camera
2.3. Ceiling/Wall Mounting without Junction Box
1. Disassemble he camera.
1) Ro a e he camera o align he no ch o one of
he marks.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 13
2) Pry he moun ing base o remove he moun ing
base wi h he camera body wi h a fla objec
(e.g., a coin).
Figure 15, Pry Open Moun ing Base
2. Pas e he drill empla e (supplied) o where you wan
o ins all he camera.
3. Drill he screw holes and he cable hole (op ional) in
he ceiling/wall according o he drill empla e.
Figure 16, Drill Templa e
NOTE: Drill he cable hole when using he ceiling
ou le o rou e he cable
4. A ach he moun ing base o he ceiling/wall, and
secure wi h supplied screws
Figure 17, A ach Moun ing Base o Ceiling
NOTE: The supplied screw package con ains self-
apping screws and expansion bol s.
For concre e wall/ceiling, expansion bol s
are required o fix he camera. For wood
wall/ceiling, self- apping screws are
required.

5. Rou e he cables hrough he cable hole or he side
opening.
6. Align he camera wi h he moun ing base, and secure
he camera on he moun ing base.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 14
Figure 18, Secure Camera o Moun ing Base
7. Connec he corresponding cables such as power
cord and video cable.
8. Power on he camera o check whe her he image on
he moni or is a an op imum angle. If no , adjus he
camera according o he figure below o ge an
op imum angle.
Figure 19, 3-Axis Adjus men
1) Hold he camera body and ro a e he enclosure o
adjus he pan posi ion [0° o 360°].
2) Move he camera body up and down o adjus he
il posi ion [0° o 75°].
3) Ro a e he camera body o adjus he ro a ion
posi ion [0° o 360°].
2.3.2 Ceiling/Wall Mounting with Junction Box
Before You Start
You need o purchase a junc ion box separa ely.
1. Pas e he drill empla e on he ceiling/wall.
2. Drill screw holes and cable hole (op ional) in he
ceiling/wall according o he drill empla e holes.
Figure 20, Junc ion Box Drill Templa e
NOTE: Drill he cable hole when using he ceiling
ou le o rou e he cable.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 15
3. Disassemble he junc ion box, and align he screw
holes of he urre camera’s moun ing base wi h
hose on junc ion box’s cover.
4. Fix he moun ing base on junc ion box’s cover by
supplied screws.
Figure 21, Ins all Turre Camera’s Moun ing Base
Figure 22, Ins all Junc ion Box Body on Ceiling/Wall
5. Secure he junc ion box’s body o he ceiling/wall
wi h supplied screws.
6. A ach he junc ion box cover o he junc ion box
body.
7. Repea s eps 5 o 8 of 2.3.1 Ceiling/Wall Moun ing
wi hou Junc ion Box
o ins all he camera o he
junc ion box.
Figure 2-8 Fix he Camera o he Junc ion Box

UM ColorVu DS-2CExxDFT-Fxx 122919NA 16
4Menu Description
Follow he s eps below o call he menu.
NOTE: The ac ual display may vary by camera model.
1. Connec he camera o he TVI DVR and he moni or.
Figure 23, Connec ions
2. Power on he camera, TVI DVR, and he moni or o view
he image on he moni or.
3. Click PTZ Con rol o en er he PTZ Con rol in erface.
4. Call he camera menu by clicking he bu on or call
he prese No. 95.
Figure 24, Main Menu Overview

UM ColorVu DS-2CExxDFT-Fxx 122919NA 17
5. Click he direc ion arrow o con rol he camera.
1) Click up/down direc ion bu on o selec he i em.
2) Click Iris + o confirm he selec ion.
3) Click lef /righ direc ion bu on o adjus he
value of he selec ed i em.
3. FORMAT
You can se he video forma o 2 MP @ 25 fps or 2 MP
@ 30 fps.
3.2 EXPOSURE
EXPOSURE describes he brigh ness-rela ed parame ers,
which can be adjus ed by EXPOSURE MODE, AGC, and
SLOW SHUTTER.
Figure 25, AE
3. . . EXPOSURE MODE
You can se he EXPOSURE MODE o GLOBAL, BLC, or WDR.
•GLOBAL refers o he normal exposure mode, which
adjus s ligh ing dis ribu ion, varia ions, and non-
s andard processing.
•BLC (Backlight Compensation) compensa es ligh o
he objec in he fron o make i clear, bu may cause
overexposure of he background where he ligh is
s rong.
•WDR (Wide Dynamic Range) helps he camera provide
clear images even under backligh circums ances.
WDR balances he brigh ness level of he whole
image and provides clear images wi h de ails.
3. .2. AGC (Auto Gain Control)
AGC op imizes he clari y of he image in poor ligh
condi ions. The AGC level can be se as HIGH, MEDIUM, or
LOW. Selec OFF o disable he AGC func ion.
NOTE: Noise will be amplified when he AGC is on.
3. .3. SLOW SHUTTER
SLOW SHUTTER increases he exposure ime on a single
frame, which makes a camera more sensi ive o he ligh
so i can produce images even in low lux condi ions.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 18
You can se he SLOW SHUTTER according o differen
ligh condi ions.
3. .4. VIDEO SETTINGS
Move he cursor o VIDEO SETTINGS and click Iris+ o
en er he sub-menu. WHITE BALANCE, BRIGHTNESS,
CONTRAST, SHARPNESS, SATURATION, 3 DNR, and MIRROR
are adjus able.
Figure 26, Video Se ings
•WHITE BALANCE. The whi e rendi ion func ion of he
camera, is o adjus he color empera ure according
o he environmen . I can remove unrealis ic color
cas s in he image. You can se WHITE BALANCE mode
o AUTO or MANUAL.
-AUTO: Whi e balance is adjus ed au oma ically
according o he color empera ure of he scene
illumina ion.
- MANUAL: You can se he R-GAIN/B-GAIN o adjus
he shades of red/blue color of he image.
Figure 27, Manual Mode
•BRIGHTNESS. Brigh ness refers o he brigh ness of
he image. You can se he BRIGHTNESS o darken or
brigh en he image. The grea er he value, he
brigh er he image.
•CONTRAST. This fea ure enhances he difference in
color and ligh be ween par s of an image.
•SHARPNESS. Sharpness de ermines he amoun of
de ail an imaging sys em can reproduce.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 19
•SATURATION. Adjus his fea ure o change he color
in ensi y.
•3 DNR (Digital Noise Reduction). The 3 DNR func ion
can decrease he noise effec , especially when
cap uring moving images in poor ligh condi ions, and
deliver a more accura e and sharper image.
•MIRROR. OFF, H, V, and HV are selec able.
-OFF: The mirror func ion is disabled
-H: The image flips 180° horizon ally
-V: The image flips 180° ver ically
-HV: The image flips 180° bo h horizon ally and
ver ically
3. .5. SMART LIGHT
Under he SMART LIGHT sub-menu, you can se he mode
o AUTO or OFF .
Figure 28, Smar Ligh
•AUTO. Under he AUTO mode, he whi e ligh urns on
au oma ically when he environmen al illumina ion
becomes poor.
-THRESHOLD value con rols he sensi ivi y of he
whi e ligh . The grea er he value, he more
sensi ive he whi e ligh .
-LEVEL value con rols he whi e ligh brigh ness.
The grea er he value, he brigh er he whi e ligh .
•OFF. This is he defaul mode.
3. .6. FUNCTIONS
In he FUNCTIONS sub-menu, you can se he privacy
mask, he motion detection, and DPC of he camera.
•PRIVACY. The privacy mask allows you o cover cer ain
areas you don’ wan o be viewed or recorded. Up o
four privacy areas are configurable.

UM ColorVu DS-2CExxDFT-Fxx 122919NA 20
Figure 29, Privacy
1. Selec a PRIVACY area.
2. Se he MODE as ON.
3. Click up/down/lef /righ bu on o define he
posi ion and he size of he area.
•MOTION. In he user-defined mo ion de ec ion
surveillance area, he moving objec can be de ec ed
and he alarm will be riggered. Up o four mo ion
de ec ion areas can be configured.
Figure 30, Mo ion
1. Selec a MOTION area.
2. Se he MODE as ON.
3. Click he up/down/lef /righ bu on o define he
posi ion and he size of he area.
•DPC (Defective Pixel Correction). Defec ive pixels are
pixels in a CMOS image sensor ha fail o sense ligh
levels correc ly.
This series of cameras suppor s defec ive pixel
correc ion. You can se he DPC as ON or OFF.
3. .7. FACTORY DEFAULT
Rese s all se ings o he fac ory defaul s.
3. .8. SAVE & EXIT
1. Move he cursor o SAVE & EXIT.
2. Click Iris+ o save he se ing and exi he menu.