HIK VISION TandemVu SE4C Series User manual

0
How to Configure Manual Tracking Function on
TandemVu Camera SE4Cxx series

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
1 of 5
1
Introduction
Our DS-2SE4Cxxx series TandemVu PTZ camera integrate a bullet camera and a PTZ camera in
one unit, the overall view remains even during the pan, tilt, and zoom maneuevers, so that users will
see everything and miss nothing at any given instant, getting unparalleled situational awareness
from the moment they set the camera up. It support 3D position and manual tracking functions,
before you use these functions, please make the calibration first to make sure the bullet and PTZ
camera in the same coordinate system.
How to Configure Manual Tracking Function on TandemVu Camera DS-S
E4Cxx series
1. Configuration Step
1) login the camera
Login camera web page, input the camera IP address in the web page (like http://192.168.1.100), then
enter the user name and password.
Note: please open the web browser as administrator, and install the web component when you first

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
2 of 5
2
use the computer.
2) Configure the calibration of camera.
Go to Configuration > PTZ >Panorama Linkage >Calibration.
Select Auto or Manual mode to calibrate the camera as below.
3) Auto Calibration configuration
Select Auto mode and click the Start Calibration button to begin.
Click the Regenerate button on the left to get the latest snap of bullet camera.

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
3 of 5
3
Then adjust the center of the PTZ camera to coincide with the bullet camera center.
Note: In this application, you can adjust the PTZ camera by pan and tilt button, or you also can
use 3D zoom function to set the center of PTZ camera.
Click the One-touch Calibration button to begin the calibration, after the calibration succeeded, please click
the Auto Calibrating Succeeded button to complete the configuration.

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
4 of 5
4
4) Manual Calibration configuration
Select Manual mode and click the Start Calibration button to begin.
Click the Regenerate button on the left to get the latest snap of bullet camera.

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
5 of 5
5
Click Add or Delete icon to add or delete the calibration point, and adjust the position of point by dragging the
green cross.
Click the calibration entry in the lower left, and adjust the center of the PTZ camera to coincide with the bullet
camera of each calibrate point.

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
6 of 5
6
Note: In this application, you can adjust the PTZ camera by pan and tilt button, or you also can
use 3D zoom function to set the center of PTZ camera.
Click the PTZ Position button to adjust the PTZ position coordinate in the lower left.
After all of the calibration point adjusted, click the Start Calibration to calibrating, then click the Complete Manual
Calibration button to complete the calibration.

Title:
How to Configure Manual Tracking Function on TandemVu Camera DS-
SE4Cxx series
Version:
V1.0
Date:
07/15/2022
Product:
IPC
Page:
7 of 5
7
5) Test the 3D zoom function or Manual tracking function on bullet camera.
Click the start 3D zoom button or start manual tracking button, then click the any position of bullet camera
preview, the PTZ camera will rotate to the center of the click position.