HIK VISION DS-K2600 Series User manual

DS-K2600 Series
Access Controller
UD.6L0206D1018A01
Quick Start Guide

DS-K2600 Serial Access Controller
1
Thank you for purchasing our product. If there is any question or request, please do not
hes itate to contact dealer.
The fi gures in the manual are for reference only.
This manual is applied for the following modules:
Module
Series
Device Name
Acces s Controller
DS-K2601
Acces s Controller
for Si ngle Door
DS-K2602
Acces s Controller
for Two Doors
DS-K2604
Acces s Controller
for Four Doors
About this Manual
This Manual is subject to domestic and international copyright protection.
Hangzhou Hikvision Digital Technology Co., Ltd. (“Hikvision”) reserves all rights to
this manual. This manual cannot be reproduced, changed, translated, or distributed,
partially or wholly, by any means, without the prior written permission of Hikvision .
Trademarks
and other Hikvision marks are the property of Hikvision and are
registered trademarks or the subject of applications for the same by Hikvision
and/or its affiliates. Other trademarks mentioned in this manual are the properties
of their respective owners. No right of license is given to use such trademarks
without express permission.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, HIKVISION MAKES NO
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE

DS-K2600 Serial Access Controller
2
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, REGARDING THIS MANUAL. HIKVISION DOES NOT WARRANT,
GUARANTEE, OR MAKE ANY REPRESENTATIONS REGARDING THE USE OF THE
MANUAL, OR THE CORRECTNESS, ACCURACY, OR RELIABILITY OF INFORMATION
CONTAINED HEREIN. YOUR USE OF THIS MANUAL AND ANY RELIANCE ON THIS
MANUAL SHALL BE WHOLLY AT YOUR OWN RISK AND RESPONSIBILITY.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL
HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU
FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES,
INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, SECURITY BREACHES, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF OR RELIANCE ON THIS
MANUAL, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY
OR CERTAIN DAMAGES, SO SOME OR ALL OF THE ABOVE EXCLUSIONS OR
LIMITATIONS MAY NOT APPLY TO YOU.
Support
Should you have any questions, please do not hesitate to contact your local dealer.

DS-K2600 Serial Access Controller
3
Regulatory information
FCC information
FCC compliance: This equipment has been tested and found to comply with the
limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interfer ence
that may cause undesired operation.
EU ConformityStatement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed

DS-K2600 Serial Access Controller
4
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal wastein the European Union. For proper
recycling, return this product to your local supplier upon the purchase of equivalent
new equipment, or dispos e of it at designated collection points. For more
information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info.

DS-K2600 Serial Access Controller
5
Preventive and Cautionary Tips
Before connecting andoperating your device, please be advised of the
following tips:
•Ensure unit is installed in a well-ventilated, dust-free environment.
•Unit is designed for indoor use only.
•Keep all liquids away from the device.
•Ensure environmental conditions meet factory specifications.
•Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the
unit as a result of dropping it may cause damage to the sensitive electronics
within the unit.
•Use the device in conjunction with an UPS if possible.
•Power down the unit before connecting and disconnecting accessories and
peripherals.
•A factory recommended HDD should be used for this device.
•Improper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries
according to the instructions provided by the manufacturer.

DS-K2600 Serial Access Controller
6
Sa fety Information
Si gns
Description
Warni ng
Follow these safeguards to prevent
serious injury or death.
Note
Follow these precautions to prevent
potentialinjury or material damage.
Ti ps
The additional information as a
complimentary of the contents.
Warnings:
Please adopt the power adapter from the legi timate factory which can meet the safety
extra low voltage (SELV) standard.
Do not i nstall, wiring, or uninstall when the power is still on.
To reduce the risk of fi re or electrical shock, do not expose this product to rain or
moisture.
This installation should be made by a qualified service person and should conform to all
the l ocal codes.
If the product does not work properly, please contact your dealer or the neares t servi ce
center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems ca used by unauthorized repair or maintenance.)
Note:
Please do not drop the objects on hard surface, and keep the equipment from the
ma gnetic field. Avoid install the equipment to the vibrated or vulnerable places.
Please do not install the devi ce in the extreme tempera ture (higher than 65℃or lower
tha n -20℃)
Keep ventilation.
Do not operate in humid envi ronment.
Do not operate in explosive environment.
Keep the device clean and dry.
Avoid bare electrical wire.

DS-K2600 Serial Access Controller
7
Table of Contents
1. PRODUCT DESCRIPTION..........................................................................................9
1.1 OVERVIEW.................................................................................................................9
1.2 PRODUCT FUNCTION..................................................................................................9
2. APPEARANCE...........................................................................................................11
2.1 INDICATORS AND SWITCHES DESCRIPTION.................................................................11
2.1.1 DS-K2600 Series Indicators and Switch es .................................................11
2.1.2 DS-K2600 Indicators and Switches ............................................................14
3. PORTS DESCRIPTION ..............................................................................................15
3.1 DS-K2601TERMINAL DESCRIPTION.........................................................................15
3.2 DS-K2602TERMINAL DESCRIPTION.........................................................................19
3.3 DS-K2604 TERMINAL DESCRIPTION........................................................................23
4. CONNECTIN G THE ACCESS CONTROL HOST ......................................................29
4.1 ADISPLAY OF INSIDE OF THE ACCESS CONTROLLER....................................................29
4.2 EXTERNAL TERMINAL DESCRIPTION ..........................................................................30
4.2.1 DS-K2601 External Terminals .....................................................................30
4.2.2 DS-K2602 External Terminals .....................................................................30
4.2.3 DS-K2604 External Terminals .....................................................................30
4.3 CONNECTING CARD READER TO ACCESS CONTROL HOST ...........................................30
4.3.1 The Connection of Wiegand Card Reader ................................................31

DS-K2600 Serial Access Controller
8
4.3.2 RS485 Card Reader Connection..................................................................32
4.4 CONNECTING E-LOCK TO ACCESS CONTROLLER.........................................................33
4.4.1 Connecting to Cathode Lock .......................................................................33
4.4.2 Connecting to Anode Lo ck ..........................................................................33
4.5 CONNECTING THE EXTERNAL ALARM DEVICE.............................................................34
4.6 CONNECTING DOOR BUTTON ...................................................................................34
4.7 CONNECTING DOOR MAGNETICS..............................................................................35
4.8 CONNECTING POWER SUPPLY...................................................................................35
4.9 ARMING REGION INPUT TERMINAL CONNECTION......................................................36
4.9.1 Connecting Normally Open Detector ........................................................36
4.9.2 Connecting No rmally Closed Detector ......................................................36
5. CONFIGURING ACCESS CON TROL HOST ............................................................37
5.1 INITIALIZING THE HARDWARE ...................................................................................37
5.2 RELAY INPUT NO/NC ..............................................................................................38
5.2.1 Lock Relay Output ........................................................................................38
5.2.2 Alarm Relay Output Status .........................................................................39
6. CONFIGURING THE ACCESS CONTROLLER VIA IV MS-4200 CLIENT ..............40
7. SPECIFICATION ........................................................................................................41

DS-K2600 Serial Access Controller
9
1. Product Description
1.1 Overview
DS-K2600 is designed with TCP/IP network interface a nd its signal processed with special
encryption and can be run offline. Anti-tampering function is also supported.
1.2 Product Function
The access controller is equipped with 32-bit high-speed processor;
Support TCP/IP network communication,wi th self-adaptive network interface. The
communication data is specially encrypted to relieve the concern of privacy leak;
Support recognition and storage of card number with maximum length of 20;
The access controller can store 100 thousand legal cards and 300 thousand card
swi ping records;
Support multi-door interlock function, anti-passback function, multi-card function,
first ca rd open function, s uper card and super password function, online upgrade
function and remote control of the doors;
Support tamper-proof alarm for card reader, alarm for door not secured, force
opening door a larm, alarm for door opening ti meout, duress card an d code alarm,
bl acklist alarm and alarm for illegal card swiping attempts reaching the limit.;
The alarm input of controller s upports short circuit protection function and
cut-proof function;
Support RS485 interface a nd Wiegand interface for accessing card reader. RS485
interface adopts dual-interface design a nd supports loop breakpoint detection and
redundancy function; Wiegand interface s upports W26,
W34 a nd is seamlessly compatible with third-party card reader with Wiegand
interface;
Support va rious card types as normal/ disabled/ blacklist/ patrol/ guest/ duress/
super ca rd, etc.;
Va rious indicators to show different status;