HIK VISION Positioning System User manual

Thermometric Bi-spectrum Network
Positioning System
User Manual
UD02221B

User Manual of Thermometric Bi-spectrum Network Positioning System
© Hikvision
1
Thank you for purchasing our product. If there are any questions, or requests, please
do not hesitate to contact the dealer.
This manual applies to Thermometric Bi-spectrum Network Positioning System.
This manual may contain several technical or printing errors, and the content is
subject to change without notice. The updates will be added to the new version of
this manual. We will readily improve or update the products or procedures described
in the manual.
Different models may differ in functions, please refer to the actual GUI of each
model.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability
of the security or signaling aspects of this product. UL has only tested for fire, shock
or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the security or signaling
aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF
ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”
0503061060818

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for Class A device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the
battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards to
prevent serious injury or
death.
Cautions Follow these precautions to
prevent potential injury or
material damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage
(SELV) standard. The power consumption cannot be less than the required value.
Do not connect several devices to one power adapter as an adapter overload may
cause over-heating and can be a fire hazard.
When the product is installed on a wall or ceiling, the device should be firmly
fixed.
To reduce the risk of fire or electrical shock, do not expose the indoor used
product to rain or moisture.
This installation should be made by a qualified service person and should
conform to all the local codes.
Please install blackouts equipment into the power supply circuit for convenient
supply interruption.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the product yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
4
Cautions:
Make sure the power supply voltage is correct before using the product.
Do not drop the product or subject it to physical shock. Do not install the product
on vibratory surface or places.
Do not expose it to high electromagnetic radiating environment.
Do not aim the lens at the strong light such as sun or incandescent lamp. The
strong light can cause fatal damage to the product.
The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor not be exposed to the laser
beam.
For working temperature, please refer to the specification manual for details.
To avoid heat accumulation, good ventilation is required for a proper operating
environment.
While shipping, the product should be packed in its original packing.
Please use the provided glove when open up the product cover. Do not touch the
product cover with fingers directly, because the acidic sweat of the fingers may
erode the surface coating of the product cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the
product cover. Do not use alkaline detergents.
Improper use or replacement of the battery may result in hazard of explosion.
Please use the manufacturer recommended battery type.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
5
Table of Contents
CHAPTER 1 OVERVIEW .................................................................................................................8
1.1 OVERVIEW...................................................................................................................................8
1.2 SYSTEM REQUIREMENT ..................................................................................................................8
1.3 FUNCTIONS..................................................................................................................................9
CHAPTER 2 NETWORK CONNECTION ..........................................................................................12
2.1 SETTING THE NETWORK POSITIONING SYSTEM OVER THE LAN .............................................................12
2.1.1 Wiring over the LAN...........................................................................................................12
2.1.2 Activating the Positioning system......................................................................................13
2.2 SETTING THE NETWORK POSITIONING SYSTEM OVER THE WAN ...........................................................18
2.2.1 Static IP Connection ...........................................................................................................18
2.2.2 Dynamic IP Connection ......................................................................................................19
CHAPTER 3 ACCESS TO THE NETWORK POSITIONING SYSTEM .................................................... 22
3.1 ACCESSING BY WEB BROWSERS .....................................................................................................22
3.2 ACCESSING BY CLIENT SOFTWARE...................................................................................................24
CHAPTER 4 LIVE VIEW ................................................................................................................26
4.1 POWER-UP ACTION.....................................................................................................................26
4.2 LIVE VIEW PAGE .........................................................................................................................26
4.3 STARTING LIVE VIEW ...................................................................................................................27
4.4 RECORDING AND CAPTURING PICTURES MANUALLY...........................................................................29
4.5 OPERATING PTZ CONTROL ...........................................................................................................30
4.5.1 PTZ Control Panel...............................................................................................................30
4.5.2 Setting / Calling a Preset....................................................................................................31
4.5.3 Setting / Calling a Patrol....................................................................................................33
4.5.4 Setting / Calling a Pattern..................................................................................................35
4.6 CONFIGURING LIVE VIEW PARAMETERS ...........................................................................................36
CHAPTER 5 PTZ CONFIGURATION ............................................................................................... 37
5.1 CONFIGURING BASIC PTZ PARAMETERS ..........................................................................................37
5.2 CONFIGURING PTZ LIMITS............................................................................................................38
5.3 CONFIGURING INITIAL POSITION ....................................................................................................39
5.4 CONFIGURING PARK ACTIONS........................................................................................................40
5.5 CONFIGURING PRIVACY MASK .......................................................................................................41
5.6 CONFIGURING SCHEDULED TASKS...................................................................................................42
5.7 CLEARING PTZ CONFIGURATIONS...................................................................................................44
5.8 CONFIGURING PTZ CONTROL PRIORITY ...........................................................................................44
CHAPTER 6 SYSTEM CONFIGURATION......................................................................................... 45
6.1 CONFIGURING LOCAL PARAMETERS ................................................................................................45
6.2 CONFIGURING TIME SETTINGS.......................................................................................................47
6.3 CONFIGURING NETWORK SETTINGS................................................................................................49

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
6
6.3.1 Configuring TCP/IP Settings ...............................................................................................49
6.3.2 Configuring Port Settings ...................................................................................................51
6.3.3 Configuring PPPoE Settings................................................................................................52
6.3.4 Configuring DDNS Settings ................................................................................................52
6.3.5 Configuring SNMP Settings................................................................................................55
6.3.6 Configuring 802.1X Settings...............................................................................................56
6.3.7 Configuring QoS Settings ...................................................................................................58
6.3.8 Configuring FTP Settings....................................................................................................58
6.3.9 Configuring UPnP™ Settings ..............................................................................................60
6.3.10 Configuring NAT (Network Address Translation) Settings .............................................61
6.3.11 Configuring Email Settings.............................................................................................61
6.3.12 Configuring HTTPS Settings ...........................................................................................63
6.4 CONFIGURING VIDEO AND AUDIO SETTINGS.....................................................................................65
6.4.1 Configuring Video Settings ................................................................................................65
6.4.2 Configuring Audio Settings ................................................................................................66
6.4.3 Configuring ROI Settings ....................................................................................................67
6.5 CONFIGURING IMAGE SETTINGS.....................................................................................................68
6.5.1 Configuring Display Settings ..............................................................................................68
6.5.2 Configuring OSD Settings...................................................................................................77
6.5.3 Configuring Text Overlay Settings......................................................................................79
6.5.4 Configuring DPC Settings ...................................................................................................79
6.6 CONFIGURING AND HANDLING ALARMS ..........................................................................................80
6.6.1 Configuring Motion Detection ...........................................................................................80
6.6.2 Configuring Video Tampering Alarm..................................................................................85
6.6.3 Configuring Alarm Input ....................................................................................................86
6.6.4 Configuring Alarm Output .................................................................................................87
6.6.5 Handling Exception ............................................................................................................88
6.6.6 Detecting Audio Exception .................................................................................................89
6.6.7 Detecting Dynamic Fire Source ..........................................................................................90
6.6.8 Detecting Ship....................................................................................................................91
6.7 TEMPERATURE MEASUREMENT .....................................................................................................91
6.7.1 Temperature Measurement Configuration ........................................................................92
6.7.2 Temperature Measurement and Alarm .............................................................................93
CHAPTER 7 VCA CONFIGURATION .............................................................................................. 96
7.1 VCA RESOURCE CONFIGURATION...................................................................................................96
7.2 CONFIGURING VCA INFORMATION .................................................................................................96
7.3 ADVANCED CONFIGURATION .........................................................................................................97
7.4 BEHAVIOR ANALYSIS ....................................................................................................................99
7.5 CONFIGURE THE VCA INFO:FOR DETAILS,SEE 7.2 VCA RESOURCE CONFIGURATION ...............................99
7.6 RULE CONFIGURATION DEMONSTRATION.......................................................................................103
Line Crossing ....................................................................................................................1037.6.1
Intrusion...........................................................................................................................1047.6.2
Region Entrance...............................................................................................................1057.6.3
Region Exiting ..................................................................................................................1067.6.4

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
7
CHAPTER 8 RECORD SETTINGS.................................................................................................. 108
8.1CONFIGURING NAS SETTINGS .....................................................................................................108
8.2 INITIALIZING AND CONFIGURING STORAGE .....................................................................................109
8.3 CONFIGURING RECORDING SCHEDULE...........................................................................................110
8.4 CONFIGURING SNAPSHOT SETTINGS .............................................................................................113
CHAPTER 9 PLAYBACK............................................................................................................... 116
CHAPTER 10 LOG SEARCHING ..................................................................................................... 120
CHAPTER 11 OTHERS .................................................................................................................. 121
11.1 MANAGING USER ACCOUNTS......................................................................................................121
Deleting a User ............................................................................................................12311.1.1
11.2 CONFIGURING RTSP AUTHENTICATION .........................................................................................123
11.3 CONFIGURING ANONYMOUS VISIT ...............................................................................................124
11.4 CONFIGURING IP ADDRESS FILTER ................................................................................................124
11.5 CONFIGURING SECURITY SERVICE SETTINGS ...................................................................................125
11.6 VIEWING DEVICE INFORMATION ..................................................................................................125
11.7 MAINTENANCE.........................................................................................................................126
11.7.1 Rebooting the Positioning system................................................................................126
11.7.2 Restoring Default Settings ...........................................................................................126
11.7.3 Importing/Exporting Configuration File.......................................................................127
11.7.4 Upgrading the System .................................................................................................127
11.8 CONFIGURING RS-485 ..............................................................................................................128
11.9 CONFIGURING SUPPLEMENT LIGHT...............................................................................................129
APPENDIX ...................................................................................................................................... 130
APPENDIX 1SADP SOFTWARE INTRODUCTION ...........................................................................................130
APPENDIX 2PORT MAPPING ...................................................................................................................132
APPENDIX 3RS485 BUS CONNECTION......................................................................................................134
APPENDIX 424VAC WIRE GAUGE &TRANSMISSION DISTANCE.....................................................................137
APPENDIX 5TABLE OF WIRE GAUGE STANDARDS.........................................................................................138
APPENDIX 6ALARM IN/OUT CONNECTIONS ...............................................................................................139

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
8
Chapter 1 Overview
1.1 Overview
Thermometric bi-spectrum network positioning system (named as positioning system
in the chapters below) integrates the function of the decoder, thermal camera, and
the high-definition zoom camera. It performs temperature measurement, dynamic
fire source detection and other smart detections in the remote surveillance of the
power system, metallurgy system, and petrochemical engineering, and so on.
You can get a high-quality live view via web browser or client software.
The figure below shows the overview of the positioning system.
Figure 1-1 Overview of Thermometric Positioning System
1.2 System Requirement
System requirement of web browser accessing is as follows:
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above
version, Mozilla Firefox 5 and above version and Google Chrome8 and above
versions.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
9
1.3 Functions
The functions vary depending on the models of positioning system.
Bi-spectrum
The positioning system has two lens, an optical one and a thermal one, and two
images are respectively provided by each lens.
PTZ Limits
The positioning system can be programmed to move within the PTZ stops (left/right,
up/down).
Scan Modes
The positioning system provides 5 scan modes: auto scan, tilt scan, frame scan,
random scan and panorama scan.
Presets
A preset is a predefined image position. When the preset is called, the positioning
system will automatically move to the defined position. The presets can be added,
modified, deleted and called.
Label Display
The on-screen label of the preset title, azimuth/elevation, zoom, time and
positioning system name can be displayed on the monitor. The displays of time and
positioning system name can be programmed.
Auto Flips
In manual tracking mode, when a target object goes directly beneath the positioning
system, the video will automatically flips 180 degrees in horizontal direction to
maintain continuity of tracking. This function can also be realized by auto mirror
image depending on different camera models.
Privacy Mask
This function allows you to block or mask certain area of a scene, for preventing the
personal privacy from recording or live viewing. A masked area will move with pan
and tilt functions and automatically adjust in size as the lens zooms telephoto and
wide.
3D Positioning
In the client software, use the left key of mouse to click on the desired position in the
video image and drag a rectangle area in the lower right direction, then the
positioning system system will move the position to the center and allow the
rectangle area to zoom in. Use the left key of mouse to drag a rectangle area in the
upper left direction to move the position to the center and allow the rectangle area
to zoom out.
Proportional Pan/Tilt
Proportional pan/tilt automatically reduces or increases the pan and tilt speeds
according to the amount of zoom. At telephoto zoom settings, the pan and tilt
speeds will be slower than at wide zoom settings. This keeps the image from moving

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
10
too fast on the live view image when there is a large amount of zoom.
Auto Focus
The auto focus enables the camera to focus automatically to maintain clear video
images.
Day/Night Auto Switch
The positioning systems deliver color images during the day. And as light diminishes
at night, the positioning systems switch to night mode and deliver black and white
images with high quality.
Slow Shutter
In slow shutter mode, the shutter speed will automatically slow down in low
illumination conditions to maintain clear video images by extending the exposure
time. The feature can be enabled or disabled.
Backlight Compensation (BLC)
If you focus on an object against strong backlight, the object will be too dark to be
seen clearly. The BLC (Backlight Compensation) function can compensate light to the
object in the front to make it clear, but this causes the over-exposure of the
background where the light is strong.
Wide Dynamic Range (WDR)
The wide dynamic range (WDR) function helps the camera provide clear images even
under back light circumstances. When there are both very bright and very dark areas
simultaneously in the field of view, WDR balances the brightness level of the whole
image and provide clear images with details.
This feature varies depending on positioning system models.
White Balance (WB)
White balance can remove the unrealistic color casts. White balance is the white
rendition function of the camera to adjust the color temperature according to the
environment automatically.
Patrol
A patrol is a memorized series of pre-defined preset function. The scanning speed
between two presets and the dwell time at the preset are programmable.
Pattern
A pattern is a memorized series of pan, tilt, zoom, and preset functions. By default
the focus and iris are in auto status during the pattern is being memorized.
Power Off Memory
The positioning system supports the power off memory capability with the
predefined resume time. It allows the positioning system to resume its previous
position after power is restored.
Timing Task
A time task is a preconfigured action that can be performed automatically at a
specific date and time. The programmable actions include: auto scan, random scan,
patrol 1-8, pattern 1-4, preset 1-8,frame scan, panorama scan, tilt scan, day, night,
reboot, PT adjust, Aux Output, etc.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
11
Park Action
This feature allows the positioning system to start a predefined action automatically
after a period of inactivity.
User Management
The positioning system allows you to edit users with different levels of permission, in
the admin login status. Multiple users are allowed to access and control the same
network positioning system via network simultaneously.
3D Digital Noise Reduction
Comparing with the general 2D digital noise reduction, the 3D digital noise reduction
function processes the noise between two frames besides processing the noise in
one frame. The noise will be much less and the video will be clearer.
Dual-VCA
Combine the detected VCA information into the video stream, which can be used for
the second-time analysis on the back-end device.
VCA Detection
The positioning system allows you to do intelligent analysis and multiple rules can be
configured for different requirements.

User Manual of Thermometric Bi-spectrum Network Positioning System
© Hikvision
12
Chapter 2 Network Connection
Before you start:
If you want to set the network positioning system via a LAN (Local Area Network),
please refer to Section 2.1 Setting the Network Positioning system over the
LAN.
If you want to set the network positioning system via a WAN (Wide Area
Network), please refer to Section 2.2 Setting the Network Positioning system
over the WAN.
2.1 Setting the Network Positioning system over the
LAN
Purpose:
To view and configure the positioning system via a LAN, you need to connect the
network positioning system in the same subnet with your computer, and install the
SADP or client software to search and change the IP of the network positioning
system.
For the detailed introduction of SADP, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a network
positioning system and a computer:
Purpose:
To test the network positioning system, you can directly connect the network
positioning system to the computer with a network cable as shown in Figure 2-1.
Refer to the Figure 2-2 to set the network positioning system over the LAN via a
switch or a router.
Network Cable
PT Camera
Figure 2-1 Connecting Directly

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
13
Network Cable
Switch or Router
PC
Network Cable
PT Camera
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Activating the Positioning system
Purpose:
You are required to activate the positioning system first before you can use the
positioning system.
Activation via Web Browser, Activation via SADP, and Activation via client software
are supported. In the following sections, activation via web browser and SADP will be
taken as examples. You may refer to the user manual of the positioning system for
the details of activation via client software.
Activation via Web Browser
Steps:
1. Power on the positioning system, and connect the positioning system to the
network.
2. Input the IP address into the address bar of the web browser, and click Enter to
enter the activation interface.
The default IP address of the positioning system is 192.168.1.64.
Figure 2-3 Activation Interface(Web)
3. Create a password and input the password into the password field.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
14
STRONG PASSWORD RECOMMENDED–We highly recommend you
create a strong password of your own choosing (using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in
order to increase the security of your product. And we recommend you
reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your
product.
4. Confirm the password.
5. Click OK to activate the positioning system and enter the live view interface.
Activation via SADP Software
SADP software is used for detecting the online device, activating the device, and
resetting the password.
Get the SADP software from the supplied disk or the official website, and install the
SADP according to the prompts. Follow the steps to activate the positioning system.
Steps:
1. Run the SADP software to search the online devices.
2. Check the device status from the device list, and select an inactive device.
Figure 2-4 SADP Interface
3. Create a password and input the password in the password field, and confirm
the password.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
15
STRONG PASSWORD RECOMMENDED–We highly recommend you
create a strong password of your own choosing ((using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in
order to increase the security of your product. And we recommend you
reset your password regularly, especially in the high security system,
resetting the password monthly or weekly can better protect your
product.
4. Click OK to save the password.
You can check whether the activation is completed on the popup window. If
activation failed, please make sure that the password meets the requirement
and then try again.
5. Change the device IP address to the same subnet with your computer by either
modifying the IP address manually or checking the checkbox of Enable DHCP.
Figure 2-5 Modify the IP Address
6. Input the password and click the Save button to activate your IP address
modification.
Activation via Client Software
The client software is versatile video management software for multiple kinds of
devices.
Get the client software from the supplied disk or the official website, and install the
software according to the prompts. Follow the steps to activate the camera.
Steps:
1. Run the client software and the control panel of the software pops up, as shown

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
16
in the figure below.
Figure 2-6 Control Panel
2. Click the Device Management icon to enter the Device Management interface,
as shown in the figure below.
Figure 2-7 Device Management Interface
3. Check the device status from the device list, and select an inactive device.
4. Click the Activate button to pop up the Activation interface.
5. Create a password and input the password in the password field, and confirm
the password.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
17
6. STRONG PASSWORD RECOMMENDED–We highly recommend you
create a strong password of your own choosing (using a minimum of 8
characters, including at least three of the following categories: upper
case letters, lower case letters, numbers, and special characters) in order
to increase the security of your product. And we recommend you reset
your password regularly, especially in the high security system, resetting
the password monthly or weekly can better protect your product.
Figure 2-8 Activation Interface
7. Click OK button to start activation.
8. Click the Modify Netinfo button to pop up the Network Parameter Modification
interface, as shown in the figure below.
Figure 2-9 Modifying the Network Parameters
9. Change the device IP address to the same subnet with your computer by either
modifying the IP address manually or checking the checkbox of Enable DHCP.

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
18
10. Input the password to activate your IP address modification.
2.2 Setting the Network Positioning system over the
WAN
Purpose:
This section explains how to connect the network positioning system to the WAN
with a static IP or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Please apply a static IP from an ISP (Internet Service Provider). With the static IP
address, you can connect the network positioning system via a router or connect it to
the WAN directly.
Connecting the network positioning system via a router
Steps:
1. Connect the network positioning system to the router.
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2
for detailed IP address configuration of the positioning system.
3. Save the static IP in the router.
4. Set port mapping, E.g., 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Refer to Appendix 2 for detailed information about port mapping.
5. Visit the network positioning system through a web browser or the client
software over the internet.
Positioning
System
Network
Cable
Router with Static IP
PC
Network
Cable
Network
Cable
Internet
Figure 2-10 Accessing the Positioning system through Router with Static IP
Connecting the network positioning system with static IP directly

User Manual of Thermometric Bi-spectrum Network Positioning system
© Hikvision
19
You can also save the static IP in the positioning system and directly connect it to the
internet without using a router. Refer to Section 2.2.2 Dynamic IP Connection for
detailed IP address configuration of the positioning system.
Positioning
System
PC
Network
Cable
Network
Cable
Internet
Figure 2-11 Accessing the Positioning system with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect
the network positioning system to a modem or a router.
Connecting the network positioning system via a router
Steps:
1. Connect the network positioning system to the router.
2. In the positioning system, assign a LAN IP address, the subnet mask and the
gateway. Refer to Section 2.1.2 for detailed LAN configuration.
3. In the router, set the PPPoE user name, password and confirm the password.
For your privacy and to better protect your system against security risks, we
strongly recommend the use of strong passwords for all functions and network
devices. The password should be something of your own choosing (Using a
minimum of 8 characters, including at least three of the following categories:
upper case letters, lower case letters, numbers, and special characters.) in
order to increase the security of your product.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
4. Set port mapping. E.g. 80, 8000 and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Refer to Appendix 2 for detailed information about port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the positioning system via the applied domain name.