HIK VISION DS-6400HDI-T User manual

DS-6400HDI-T Series Decoder
USER MANUAL
Version 1.0.0

User Manual of DS-6400HDI-T Decoder
1
Hikvision Network Digital Video Recorder User’s Manual
This manual, as well as the software described in it, is furnished under license and may be used or copied only in
accordance with the terms of such license. The content of this manual is furnished for informational use only, is
subject to change without notice, and should not be construed as a commitment by Hikvision Digital Technology
Co., Ltd. (Hikvision). Hikvision assumes no responsibility or liability for any errors or inaccuracies that may
appear in the book.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior
written permission of Hikvision.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
REGARDING THE HIKVISION SOFTWARE. HIKVISION DOES NOT WARRANT, GUARANTEE, OR
MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE
HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS, ACCURACY, RELIABILITY,
CURRENTNESS, OR OTHERWISE. THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF
THE HIKVISION SOFTWARE IS ASSUMED BY YOU. THE EXCLUSION OF IMPLIED WARRANTIES IS
NOT PERMITTED BY SOME STATES. THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE
TO YOU FOR ANY CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES (INCLUDING
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, AND THE LIKE) ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION
SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATIONS MAY NOT APPLY TO
YOU.

User Manual of DS-6400HDI-T Decoder
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the Low
Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol cannot be disposed of as
unsorted municipal waste in the European Union. For proper recycling, return this product to
your local supplier upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union. See the product documentation for specific
battery information. The battery is marked with this symbol, which may include lettering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see: www.recyclethis.info.
Description on Laser Specification
The optical disc drive such as DVD Super Multi (Double Layer) Drive 22X that is used in this computer is
equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
CLASS 1 LASER
PRODUCT TO IEC60825-1
LASER KLASSE 1
The drive with the above label is certified by the manufacturer that the drive complies with the requirement for
laser product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the United
States of America, Department of Health & Human Services, Food and Drug Administration.
In other countries, the drive is certified to comply with the requirement pursuant to IEC 60825-1 and EN 60825-1
on class 1 laser product.
This computer is equipped with the optical disc drive in the following list according to the model.

User Manual of DS-6400HDI-T Decoder
3
Safety Warnings and Cautions
Please pay attention to the following warnings and cautions:
Hazardous Voltage may be present: Special measures and precautions must be
taken when using this device. Some potentials (voltages) on the device may present a
hazard to the user. This device should only be used by Employees from our company with
knowledge and training in working with these types of devices that contain live circuits.
Power Supply Hazardous Voltage: AC mains voltages are present within the power supply assembly. This
device must be connected to a UL approved, completely enclosed power supply, of the proper rated voltage and
current. No user serviceable parts inside the power supply.
System Grounding (Earthing): To avoid shock, ensure that all AC wiring is not exposed and that the earth
grounding is maintained. Ensure that any equipment to which this device will be attached is also connected to
properly wired grounded receptacles and are approved medical devices.
Power Connect and Disconnect: The AC power supply cord is the main disconnect
device to mains (AC power).The socket outlet shall be installed near the equipment and
shall be readily accessible.
Installation and Maintenance: Do not connect/disconnect any cables to or perform
installation/maintenance on this device during an electrical storm.
Power Cord Requirements: The connector that plugs into the wall outlet must be a grounding-type male
plug designed for use in your region. It must have certification marks showing certification by an agency in your

User Manual of DS-6400HDI-T Decoder
4
region. The connector that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13,
female connector. See the following website for more information http://kropla.com/electric2.htm.
Lithium Battery: This device contains a Lithium Battery. There is a risk of explosion
if the battery is replaced by an incorrect type. Dispose of used batteries according to the
vendor’s instructions and in accordance with local environmental regulations.
Perchlorate Material: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is required by California Code
of Regulations, Title 22, Division 4.5, Chapter 33: Best Management Practices for Perchlorate Materials. This
device includes a battery which contains perchlorate material.
Taiwan battery recycling:
Please recycle batteries.
Thermal and Mechanical Injury: Some components such as heat sinks, power
regulators, and processors may be hot; care should be taken to avoid contact with these
components.
Electro Magnetic Interference: This equipment has not been tested for
compliance with emissions limits of FCC and similar international regulations. This device is not, and may not be,
offered for sale or lease, or sold, or leased until authorization from the United States FCC or its equivalent in other
countries has been obtained. Use of this equipment in a residential location is prohibited. This equipment
generates, uses and can radiate radio frequency energy which may result in harmful interference to radio
communications. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is required to take measures to eliminate the interference
or discontinue the use of this equipment.
Lead Content:
Please recycle this device in a responsible manner. Refer to local environmental
regulations for proper recycling; do not dispose of device in unsorted municipal
waste.

User Manual of DS-6400HDI-T Decoder
5
Preventive and Cautionary Tips
Before connecting and operating your DVS, please be advised of the following tips:
•Ensure unit is installed in a well-ventilated, dust-free environment.
•Keep all liquids away from the DVS.
•Please check the power supply to avoid the damage caused by voltage mismatch.
•Please make sure the DVS work in the allowed range of temperature and humidity.
•Please keep the device horizontal and avoid the installation under severe vibration environment.
•The dust board will cause a short circuit after damping; Please remove dust regularly for the board, connector,
chassis fan and other parts of the device with brush.
•Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.

User Manual of DS-6400HDI-T Decoder
6
CHAPTER 1 Introduction........................................................................................................ 8
1.1 Description ...................................................................................................................... 9
1.2 Features ........................................................................................................................... 9
CHAPTER 2 Panel and Connections ..................................................................................... 11
2.1 Front Panel .................................................................................................................... 12
2.2 Rear Panel...................................................................................................................... 12
CHAPTER 3 Initial Network Parameters Configuration ........................................................ 13
3.1 Connecting the decoder by Hyper Terminal Tools........................................................ 14
3.2 Network Configuration by Hyper Terminal.................................................................. 16
CHAPTER 4 Decoder Configuration and Operation by Web Browser .................................. 18
4.1 Decoding Operation....................................................................................................... 19
4.1.1 Dynamic Decode .................................................................................................... 22
4.1.2 Cycle Decoding...................................................................................................... 23
4.1.3 Remote Playback.................................................................................................... 25
4.1.4 Global Switch for the Decoding Channels ............................................................. 26
4.1.5 Image Scaling......................................................................................................... 26
4.1.6 Picture Overlay....................................................................................................... 27
4.1.7 Checking the Connection Status............................................................................. 28
4.1.8 Checking the Decode Channel Status..................................................................... 28
4.1.9 Checking the Display Channel Status .................................................................... 29
4.1.10 Transparent Channel............................................................................................. 29
4.2 Parameter Configuration for Decoder ........................................................................... 30
4.2.1 Checking Device Information ................................................................................ 30
4.2.2 Time Settings.......................................................................................................... 30
4.2.3 Basic Network Settings .......................................................................................... 31
4.2.4 DDNS Settings ....................................................................................................... 31
4.2.5 Alarm Input / Output Settings ................................................................................ 32
4.2.6 Arming Time.......................................................................................................... 33
4.2.7 Account Management............................................................................................. 33
4.2.8 Rebooting, Upgrading and Restoring the Default Settings for the Decoder ......... 34

User Manual of DS-6400HDI-T Decoder
7
CHAPTER 5 Decoder Configuration and Operation by Client Software............................... 36
5.1 Adding, Modifying and Deleting the Decoder.............................................................. 37
5.1.1 Adding the Decoder to the Client Software............................................................ 37
5.1.2 Deleting and Modifying the Decoder to the Client Software................................. 39
5.2 TV Wall Layout Settings............................................................................................... 40
5.3 Setting the Decoding Channel for the Decoder............................................................. 42
5.4 Remote Setting for Decoders......................................................................................... 44
CHAPTER 6 Appendix........................................................................................................... 45
Appendix A Specifications.................................................................................................. 46
Appendix B. FAQ................................................................................................................ 47

User Manual of DS-6400HDI-T Decoder
8
CHAPTER 1
Introduction

User Manual of DS-6400HDI-T Decoder
9
1.1 Description
Designed for the high-definition video monitoring system, DS-6400HDI-T Series HD Video/Audio
Decoder is developed on the basis of TI platform, Linux operating system and Netra processor,
ensuring high reliability and stability of system running.
DS-6400HDI-T Series HD Video/Audio Decoder is capable of decoding video at 1080P resolution and
outputting decoded video via VGA and HDMI interfaces, and it also supports multiple network
protocols and multiple stream transmission mode, thus provides a strong support to the large-scale TV-
Wall decoding.
1.2 Features
Decoding images and audio
Private H.264, standard H.264, MJPEG and MPEG4 formats video compression methods are
supported;
Support PS, RTP and private customized data encapsulation formats;
PAL and NTSC image standards supported;
Decode at up to 5MP resolution;
G.722, G.711A, G.711U and MPEG2-L2 formats audio compression methods.
High-definition video output via VGA and HDMI. For 6401HD-T decoder, BNC output is also
available.
TV Wall montage is supported.
Decoding Capacity
DS-6401HDI is capable of decoding 1 channel video stream at 5MP or 1080P resolution, 2 channels
video stream at 720P resolution and 4 channels video stream at 4CIF resolution.
DS-6404HDI is capable of decoding 4 channel video stream at 5MP or 1080P resolution, 8 channels
video stream at 720P resolution and 16 channels video stream at 4CIF resolution.
DS-6408HDI is capable of decoding 8 channel video stream at 5MP or 1080P resolution, 16 channels
video stream at 720P resolution and 32 channels video stream at 4CIF resolution.
Decoding Mode
Dynamic decoding: log on the remote encoder or remote stream media server to select a channel of
video source to acquire video stream, and then decode and output the video for local display.
Cycle decoding: set multiple remote monitoring channels on a decoding channel, and the decoder is
capable of performing cycle decoding according to the configured sequence and time. The stream
sources can be obtained via remote access to the encoder or stream media server and decoded for

User Manual of DS-6400HDI-T Decoder
10
local output. A maximum of 64 channels are allowed for cycle decoding.
Obtain stream from stream media server: The decoder can receive real-time data by access to
stream media server, and then decode the video stream and output them on the TV Wall. The private
RTSP is adopted as the control protocol, and the TCP/UDP is used for receiving the data stream.
Remote playback of record files: by remote access to the encoding devices with storage capability,
and directly obtain the record files from the encoder, and finally decode for local output.
Network
One 10/100/1000Mbps self-adaptive Ethernet interface;
Support TCP, UDP and Multicasting network protocols;
DHCP, NTP, HTTP, RTP and DDNS are supported;
Remote upgrading and maintenance can be done via web browser or client software.
User Administration
A maximum of 32 users can be created by the system, including 1 administrator and 31 users. The
user name of the administrator is admin, which cannot be modified, and the password is allowable to
be modified by the administrator only; no deletion of the administrator is allowed, and the
administrator is authorized to set the operation permissions for other users.
Transparent Channel
The decoder adopts the RS-232/RS-485 serial interface to realize transparent transmission. The data
sent remotely to the decoder via network can be transmitted by RS-232/RS-485 interface of decoder
without any operation, and the transparent channel of the decoder supports multicast transparent
transmission as well, and multiple transparent channels can be established simultaneously.
Two-way audio
The decoder is capable of realizing voice talk with the remote client.

User Manual of DS-6400HDI-T Decoder
11
CHAPTER 2
Panel and Connections

User Manual of DS-6400HDI-T Decoder
12
2.1 Front Panel
2.2 Rear Panel
LED Indicator & Interface
Connections
1
PWR
Power LED indicator
2
LINK
Network connection LED indicator
3
RX/TX
Data transmitting/receiving status LED indicator
Interface
Connections
1
VAG 1~ VGA8
VGA decoding output
2
HDMI video output
HDMI decoding output
3
LINE IN/OUT
Two-way audio
4
AUDIO OUT
Audio out, for connection to audio output device, e.g. sound box. R: right
channel; L: left channel
5
RS-232 serial interface
Connect to RS-232 devices, e.g., PC, etc.
6
LAN
10/100/1000 Mbps Ethernet interface
7
RS-485 serial interface
Connect to RS-485 devices, e.g., Dome camera, etc.
8
Alarm In
4 alarm inputs
Alarm Out
4 alarm outputs
9
GND
Grounding
10
Power Switch
Power On/Off Switch
11
Power Supply
Power input interface

User Manual of DS-6400HDI-T Decoder
13
CHAPTER 3
Initial Network Parameters Configuration

User Manual of DS-6400HDI-T Decoder
14
Purpose:
If you don’t know the IP address of the decoder and this is not the first time you use the decoder, you
can use SADP (IP finder) software or the Serial port tools to find out the IP address of the decoder and
to configure the IP address or other network parameters of it. It is recommended to change the default
IP address for the first time to use it.
This chapter aims to tell the procedures of using the Hyper Terminal Software to find and configure the
IP address and other parameters of the device.
For the operation of the SADP software, please refer to the User Manual of the SADP software.
Note:
For the first-time user, the default user name of DS-6400HDI-T is admin, and password is 12345. And
the default IP address is 192.0.0.64.
3.1 Connecting the decoder by Hyper Terminal
Tools
Purpose:
By connecting decoder and PC with serial line via RS-232 interface, run the Hyper Terminal application, you can
get and modify the network parameters of the decoder with serial commands.
Steps:
1. Run the Hyper Terminal application on your PC
2. Input a name (e.g. HK) and select an icon
3. Click OK to enter the next dialogue box.

User Manual of DS-6400HDI-T Decoder
15
4. Select COM1 in Connect using filed (Please select the COM port according to the real scenario.).
5. Click OK to enter the Properties dialogue box.
6. Set port parameters in COM1 Properties dialogue box shown as the following figure.
Bits per second: 115200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
7. Click Apply and OK after the setup. Press Enter under Hyper Terminal interface.
When [root@dvrdvs/]# appears, the connection is established.

User Manual of DS-6400HDI-T Decoder
16
Disconnecting and saving the connection
When you disconnect the session, the following dialogue box pops out to ask you whether you want to save the
session. If you save the session, the name of the session is kept and when the next time you use the Hyper Terminal
Tools you can see an icon named with the session you saved.
3.2 Network Configuration by Hyper Terminal
After the successful connection of the Hyper Terminal, you can get to the operation interface of the hyper terminal
interface.

User Manual of DS-6400HDI-T Decoder
17
Commands Description:
Commands
Utilities
helpm
Print common commands, show as Figure 3.2.
getIp
Show the current IP address of decoder. Command format: getIp
setIp
Set up IP address of decoder.
Command format: setIp IP: mask, e.g. setIp 192.168.1.10:255.255.255.0
getGateway
Show current decoder gateway address. Command format: getGateway
setGateway
Set up gateway of the decoder.
Command format: setGateway Gateway, e.g. setGateway 192.168.1.1
Note:
Press Enter button to execute the command in the Hyper Terminal Tools. And please strickly follow the format of
the command lines, otherwise, the command you input is seen as invalid.

User Manual of DS-6400HDI-T Decoder
18
CHAPTER 4
Decoder Configuration and Operation by
Web Browser

User Manual of DS-6400HDI-T Decoder
19
Purpose:
Since there is no local operation GUI provided for the decoder, you can manage and configure it by web browser
or the iVMS client software. In this chapter, the operation and management of the decoder by the web browser is
provided.
Note: The tested Web browsers include: IE7 and IE8, chrome, safari and firefox4.
Open the Web browser and input the IP address of Decoder (e.g., http://172.9.108.108) to enter the login page:
Enter the user name and password of the device in the dialog box and then click Login to log into the system. By
default, the user name for login is admin and the password is 12345.
The main interface of the control panel of the decoder is showed after successful login.
4.1 Decoding Operation
Purpose:
To realize the display of the decoded video on the TV wall, you must set the decoding operation parameters.
Before you start:
Check the cabling of the decoder, and ensure that the decoder is connected to the TV wall or monitor via the video
output interfaces.
To set the video output of the decoder, the first step is to choose the video output interfaces. There are 3 video
output interfaces, the VGA, HDMI and the BNC outputs.
Steps: