HIK VISION DS-2CC1282P(N)-IT3 User manual

IR Bullet Camera
User Manual
UD.6L0201D0089A01

IR Bullet Camera·User Manual
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual applies to
Type
Model
Ⅰ
DS-2CC1282P(N)-IT3
DS-2CC12A2P(N)-IT3
Ⅱ
DS-2CC1282P(N)-IT5
DS-2CC12A2P(N)-IT5
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.
0100001021208

IR Bullet Camera·User Manual
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies w ith part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

IR Bullet Camera·User Manual
3
3
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked w ith this
symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.

IR Bullet Camera·User Manual
4
4
Table of Contents
1 Introduction ........................................................................5
1.1 Product Features ......................................................5
1.2 Overview .................................................................6
2 Installation..........................................................................8
2.1 Wall Mounting ..........................................................8
2.2 Wiring .................................................................... 11
Appendix...............................................................................12
1 Glossary ................................................................... 12
2 Troubleshooting......................................................... 16
3 Technical Maintenances ............................................. 19

IR Bullet Camera·User Manual
5
5
1Introduction
1.1 Product Features
This series of camera adopts a new generation sensor with high
sensitivity and advanced circuit design technology. It features high
resolution, low image distortion and low noise, etc., which makes it
suitable for surveillance system and image processing system.
High-performance sensor and high resolution bring
high-quality image
IR LED enables the day/night surveillance
Day/Night auto switch
ATW, which brings high color rendition
Auto electronic shutter control to adapt to the different
surveillance environments
Auto gain control, adaptive brightness
High SNR brings high-quality image
Ingress protection: IP66

IR Bullet Camera·User Manual
6
6
1.2 Overview
1
2
3
4
5
6
Figure 1-1 Overview of Type ⅠBullet Camera
Table 1-1 Description
No.
Description
No.
Description
1
Sun Shield
4
Adjustable Screw
2
Lens
5
Power Cable
3
IR LED
6
Video Cable

IR Bullet Camera·User Manual
7
7
1
2
3
4
5
6
Figure 1-2 Overview of Type ⅡBullet Camera
Table 1-2 Description
No.
Description
No.
Description
1
Sun Shield
4
Adjustable Screw
2
Lens
5
Power Cable
3
IR LED
6
Video Cable

IR Bullet Camera·User Manual
8
8
2Installation
Before you start:
Please make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off during
the installation.
Check the specification of the products for the installation
environment.
Check whether the power supply is matched w ith your AC
outlet to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
2.1 Wall Mounting
IR bullet camera is w idely used in the low luminance indoor
environment, and wall mounting is recommended. We will take the
wall mounting as an example to explain the installation steps.
Note:Please make sure that the wall is strong enough to
withstand 3 times the weight of the camera and the bracket.
Steps:
1. Adjust the Sun Shield

IR Bullet Camera·User Manual
9
9
Push the sun shield to the outermost position and tighten the
adjustable screw.
Figure 2-1 Adjust the Sun Shield
2. Secure the Mount
Secure the wall mount to the wall with the screws.
Notes:
The wall mount you select should be at least 1.5 times longer
than the bullet camera.
If the wall is the cement wall, you need to insert the expansion
screws before you install the wall mount. If the wall is the
wooden wall, you can use self-tapping screw to secure the
wall mount.
Push

IR Bullet Camera·User Manual
10
10
Figure 2-2 Secure the Wall Mount
3. Install the Camera
Secure the camera to the wall mount with the screws.
Figure 2-3 Install the Camera

IR Bullet Camera·User Manual
11
11
2.2 Wiring
Figure 2-4 The Power Cable and the Video Cable
Note: Please make sure that the power adapter is compatible w ith
the camera, and the standard power supply is 12V DC. Please refer
to the technical specification for more information.

IR Bullet Camera·User Manual
12
12
Appendix
1 Glossary
Note:
The glossary gives brief explanations to the basic operation
principle or the basic function of the camera. However, it doesn’t
mean the listed functions are all supported by the camera
mentioned in this user manual. Please take the function in the
corresponding specification as the standard.
Definition:
Definition is the degree to distinguish the edge between two parts.
Contrast:
Contrast is the color difference between the brightest and darkest
parts.
Saturation:
Saturation is the degree of color purity. The color is purer, the
image is brighter.
DAY/NIGHT Auto Switch:
The cameras deliver color images during the day. And as light
diminishes at night, the cameras switch to night mode and deliver
black and white images with high quality.
AGC:
AGC is a control circuit that automatically changes the gain of a
receiver or other pieces of equipment, so that the desired output

IR Bullet Camera·User Manual
13
13
signal remains essentially. When under low illumination, AGC will
regulate the gain and amplification of the video signal.
S/N ratio:
It is the ratio of Signal voltage to noise voltage. The ratio is larger,
the effect of noise is less, and the image is clearer.
White Balance:
White balance can remove the unrealistic color casts. White
balance is the white rendition function of the camera to adjust the
color temperature according to the environment automatically.
BLC:
If you focus on an object against strong backlight, the object will
be too dark to be seen clearly. The BLC (Backlight Compensation)
function can compensate light to the object in the front to make it
clear, but this causes the over-exposure of the background where
the light is strong.
SMART IR:
The SMART IR adopts the smart image processing technique to
automatically adjust the brightness curve by detecting multi-zone
brightness, and so as to prevent the over exposure of central point
existed in short IR distance conditions.
Motion Detection:
In the user-defined motion detection surveillance area, the moving
object can be detected and trigger alarm. The sensitive level can
be customized according to the environment.
Privacy Mask:

IR Bullet Camera·User Manual
14
14
This function allows you to block or mask certain area of a scene,
thus prevent the personal privacy from recording or live viewing.
OSD (On Screen Display):
OSD is the texts superimposed on a screen. It can show the menu
on the screen.
Synchronous System:
There are two modes for the camera synchronization. Internal
synchronization is realized by the synchronous signal which is
generated by the inside crystal oscillator.
ICR Auto Switch:
The filter will filter infrared light during the daytime and change to
normal filter at night to ensure a high sensitivity and clear image.
WDR (Wide Dynamic Range):
The wide dynamic range (WDR) function helps the camera provide
clear images even under back light circumstances. When there are
both very bright and very dark areas simultaneously in the field of
view, WDR balances the brightness level of the whole image and
provide clear images with details.
EIS (Electronic Image Stabilization):
Electronic image stabilization function can reduce certain ranges of
vibration which is caused by the external environment.
3D Digital Noise Reduction:
Comparing w ith the general 2D digital noise reduction, the 3D
digital noise reduction function processes the noise initiated by
CCD besides processing the noise in the separated Y video signal
and C video signal.

IR Bullet Camera·User Manual
15
15
HLC (Highlight Compensation):
The HLC is capable of detecting and reversing the bright spots in
the picture (such as headlights) to black so as to achieve optimum
picture quality.
Digital Zoom:
Digital zoom helps to crop the entire image, and then digitally
enlarge the size of a portion of image that is needed to zoom in on.

IR Bullet Camera·User Manual
16
16
2 Troubleshooting
Problem 1:
Why does the camera restart intermittently? And the problem is
much more serious when infrared lights of IR camera are turned on
at night.
Possible Reasons:
The main and common reason is power supply shortage. This
problem may happen to the IR camera especially at night, because
the infrared lights are turned on at night and increase the power
consumption.
To Solve the Problem:
You need to ensure that the power supply matches with ±10% of
the nominal voltage. And the power consumption of power adapter
should meet the demand of the camera.
Problem 2:
The camera can never be focused by adjusting the focus-stick on
the lens. And there is also no use adjusting the back focus.
Possible Reasons:
The camera needs the lens with CS lens mount. When you install a
lens with C lens mount, the camera will never focus.
To Solve the Problem:
You can change a lens with CS lens mount to the camera.
Or you can use a C/CS adapter ring between the camera and the
lens with C lens mount.

IR Bullet Camera·User Manual
17
17
Problem 3:
The camera is installed w ith an auto-iris lens. You adjust the focus
to get a clear image in the daytime. But the image is defocused at
night.
Possible Reasons:
In the daytime, the illumination is high, so the iris is adjusted to a
small size automatically. The DOF (depth of field) is long. But at
night, the iris is adjusted to a large size automatically, so the DOF
is shortened. The focus you adjusted in the daytime now locates
out of the DOF, so the image is defocused at night.
To Solve the Problem:
When you adjust the focus for a camera w ith an auto -iris lens, you
need to set the lens type to AES (auto electronic shutter) mode.
Under AES mode, the iris is adjusted to the largest size
automatically. Then you can adjust the focus to get a clear image.
At last, you need to set the lens type back to AI (auto iris) mode.
Or you can adjust the focus in low illumination condition, such as at
night.
Problem 4:
A camera with OSD menu and an auto-iris lens displays black video.
But the OSD menu can be called and displayed.
Possible Reasons:
Auto-iris lens connector is loose contact.
Or the iris driven mode of the camera does not match with the
mode of auto-iris lens.

IR Bullet Camera·User Manual
18
18
To Solve the Problem:
Check the auto-iris lens connector to ensure good contact.
Set the iris driven mode of the camera the same as that of lens.
The modes can be VD (video drive) or DD (direct drive). DD mode
is commonly used.

IR Bullet Camera·User Manual
19
19
3 Technical Maintenances
Lens Maintenance
The lens surface is plated an anti-reflection coating. The dust, oil
and finger print, etc. w ill cause scratch, mildewed and
performance degraded. Please refer to the following method to
clean the lens.
Handling dust
Use oil free soft brush or blowing dust ball to clean the dust.
Handling o il
Steps:
1. Wipe off the water-drop or oil by soft cloth and dry the lens.
2. Use oil free cotton cloth or lens clean paper to wipe the lens
from center to outside with alcohol or detergent.
3. Change the cloth to wipe the lens until the lens is clean.
Bubble Maintenance of Domes
The bubble is of transparent plastic. The dust, oil a nd finger print,
etc. will cause scratch or image blur. Please refer to the fo llowing
method to clean the bubble.
Handling dust
Use oil free soft brush or blowing dust ball to clean the dust.
Handling o il
Steps:
1. Wipe off the water-drop or oil by soft cloth and dry the bubble.
2. Use oil free cotton cloth or bubble clean paper to wipe the
bubble from center to outside with alcohol or detergent.