HIK VISION DS-2CD2412F-I User guide

UD.6L0201B1191A01
Network Camera
Quick Operation Guide

Network Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
About This Document:
This manual applies to DS-2CD2412F-I(W); DS-2CD2432F-I(W)
series cameras.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.
0500051030809

Network Camera·Quick Operation Guide
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

Network Camera·Quick Operation Guide
3
3
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.

Network Camera·Quick Operation Guide
4
4
Contents
1 Appearance Description ................................................ 5
2 Notice............................................................................ 8
3 Installation ................................................................. 10
4 Setting the Network Camera over the LAN .................. 15
5 Accessing via WEB browser......................................... 20

Network Camera·Quick Operation Guide
5
5
1Appearance Description
1
2
3
4
5
6
7
8
9
10
11
12
Figure 1-1 Overview
Table 1-1 Description
No.
Description
1
Lens
2
PIR(Passive Infrared) sensor
3
Microphone
4
Indicators
Alarm:
Solid red when the camera is armed;
Solid blue when the camera is
unarmed.

Network Camera·Quick Operation Guide
6
6
No.
Description
Status: Reserved
Link:
Flashing amber when network
connection is functioning properly;
Unlit when no network connection;
5
Infrared Light
6
SD Card Slot
7
10M / 100M self-adaptive Ethernet interface & PoE
8
WPS (Wi-Fi Protected Setup)/Reset Button
9
Alarm Input Interface
10
Ground
11
Alarm Output Interface
12
Power supply interface; (DC 12V)
To reset the default parameters to the camera, you need to
press and hold the RESET button and power on the camera.
After the power on of the camera, you must still press and hold
the Reset button for about 10 seconds.
The WPS button is an easy configuration protocol of Wi-Fi
settings. Press the WPS button on the camera and press the

Network Camera·Quick Operation Guide
7
7
WPS button on the wireless router, the camera can be easily
connected on line.

Network Camera·Quick Operation Guide
8
8
2Notice
Do not install the camera
in the extreme whether
condition.
Do not touch the lens with
your figure.
Do not install the camera
towards the strong light
or in the unstable
lightening condition.
Do not subject the
camera to vibration,
shock or heavy pressure.

Network Camera·Quick Operation Guide
9
9
High humidity may
damage the camera
hardware; put it in dry
and well-ventilated place.
Under no circumstances
should you submerge the
camera in any type of
liquid.
Electromagnetic radiation may affect the video data
transmission and the image quality. Do not install the
camera near

Network Camera·Quick Operation Guide
10
10
3Installation
Read the following contents carefully before the installation.
Make sure that all the related equipment is power-off during
the installation.
Check whether the power supply is matched with your AC
outlet to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Make sure the installation location does not have reflective
surfaces of objects close to the camera. The IR light from the
camera may reflect back into the lens causing reflection.
The cube camera can be installed on wall, ceiling or table. Ceiling
mounting is taken as an example in this section; if you adopt wall
mounting or table mounting, you can also take below procedure as
a reference.
Steps:
1. Open the cover on the mounting base from the bracket.

Network Camera·Quick Operation Guide
11
11
Figure 3-1 Open the Cover
2. Stick the drilling template to the ceiling.
Figure 3-2 Drilling Template
For cement ceiling mounting, you need to use the expansion
screw to fix the camera. The mounting hole of the expansion
pipe on the wall should align with the mounting hole of the
drilling template.

Network Camera·Quick Operation Guide
12
12
For wooden ceiling mounting, you can just use the self-tapping
screw to fix the camera.
The ceiling must be strong enough to withstand more than 3
times the weight of the camera.
Figure 3-3 Stick the Drilling Template
3. Use 3 screws to fix the bracket to the ceiling and the screw hole
on the bracket should align with the mounting hole on the
drilling template.
Figure 3-4 Fix the Bracket
4. Install the mounting base cover and attach the camera on the
bracket.
Drilling template

Network Camera·Quick Operation Guide
13
13
Figure 3-5 Install the Cover and Camera
5. Adjust surveillance angel
1). Loosen the knob to adjust the panning position and tilting
position.
2). After adjusting the angle of the camera to the desired
position, fasten the knob.

Network Camera·Quick Operation Guide
14
14
Figure 3-6 Adjust the Camera
Knob

Network Camera·Quick Operation Guide
15
15
4Setting the Network
Camera over the LAN
Purpose:
To view and configure the camera via LAN (Local Area Network),
you need to connect the network camera in the same subnet with
your PC. Then, install the SADP or iVMS-4200 software to search
and change the IP of network camera.
The SADP and iVMS-4200 software are on the disk in the camera
packet.
Connection of network camera and PC:
\
Figure 4-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
Network Cable
Network Cable

Network Camera·Quick Operation Guide
16
16
1. To get the IP address, you can choose either of the following
methods:
Use SADP, a software tool which can automatically detect
network camera in the LAN and list the device information like
IP address, subnet mask, port number, device serial number,
device version, etc., shown in Figure 4-2.
Use iVMS-4200 software and to list the online devices. Please
refer to the user manual of client software for detailed
information.
2. Change the IP address and subnet mask to the same subnet as
of your PC.
Refer to the following introductions to set IP address with
SADP software:
Search active devices online
Search online devices automatically:
After running the SADP software, it automatically searches
the online devices every 15 seconds from the subnet where
your computer locates. It displays the total number and
information of the searched devices in the Online Devices
interface. Device information including the device type, IP
address, port number, gateway, etc. will be displayed.

Network Camera·Quick Operation Guide
17
17
Figure 4-2 Searching Online Devices
Device can be searched and displayed in the list in 15
seconds after it goes online; it will be removed from the list
in 45 seconds after it goes offline.
Search online devices manually:
You can also click to refresh the online device
list manually. The newly searched devices will be added to
the list.

Network Camera·Quick Operation Guide
18
18
You can click or on each column heading to order
the information; you can click to show the device
table and hide the network parameter panel on the right
side, or click to show the network parameter panel.
Modify device information
Steps:
1). Select the device to be modified in the device list as shown
in Figure 4-3. The network parameters of the device will be
displayed in the Modify Network Parameters panel on the
right side as shown in Figure 4-4.
2). Edit the modifiable network parameters, e.g. IP address
and port number.
3). Enter the password of the admin account of the device in
the Password field and click to save the
changes.
Figure 4-3 Select a device

Network Camera·Quick Operation Guide
19
19
Figure 4-4 Modify Network Parameters
3. Enter the IP address of network camera in the address field of
the web browser to view the live video.
The default value of the IP address is “192.0.0.64”. The default
user name is “admin”, and password is “12345”.
For accessing the network camera from different subnets,
please set the gateway for the network camera after you log
in.