HIK VISION DS-2CD8253F-EI User guide

Network Camera
V4.0.1
Quick Operation Guide

Network Camera·Quick Operation Guide
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer. This
manual applies to DS-2CD8253F-EI(Z), DS-2CD8233F-EI(Z),
DS-2CD8264FWD-EI(Z), DS-2CD8264F-E, DS-2CD8254F-EI,
DS-2CD8254FWD-E, DS-2CD8283F-EI, DS-2CD8255F-EI
cameras.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.

Network Camera·Quick Operation Guide
2
2
1Physical Description of
Camera
1.1 Camera Description
Note: Two types of interfaces of cameras as shown in Figure 1-1
and Figure 1-2. Please choose the right figure according to the
appearance of your camera.
Figure 1-1 Overview
Figure 1-2 Overview

Network Camera·Quick Operation Guide
3
3
Table 1-1 Physical Description
No.
Description
1
10M/100M self-adaptive Ethernet interface
2
Power supply interface
3
IN, G: Alarm input interface
1A, 1B: Alarm output interface
4
D+, D-: RS-485 interface
5
AUDIO IN, G: Audio input interface
AUDIO OUT, G: Audio output interface
1.2 Camera Wiring Diagram
Figure 1-3 Wiring Diagram

Network Camera·Quick Operation Guide
4
4
2Installation
Note:
Verify the package contents are correct by checking the items
against the packing list.
Read the following contents carefully before the installation.
Make sure that all the related equipment is power-off during
the installation.
Check whether the power supply is matched with your AC
outlet to avoid any damage.
Do not place the camera in extremely hot or damp
environment. To avoid heat accumulation, good ventilation is
required for a proper operating environment.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
The bullet camera can be installed to both wall and ceiling. This
quick guide takes wall mounting steps as an example.
Steps:
1. Fix the mounting base to the wall. The mounting base can also
be used to keep the cables.

Network Camera·Quick Operation Guide
5
5
Figure 2-1 Fix the Mounting Base
Note:
Please apply water-proof measures between the ceiling
surface and mounting base and around the cables.
For cement wall mounting, you need to use the expansion
screw to fix the mounting base. The mounting hole of the
expansion pipe on the wall should align with the mounting
hole on the mounting base.
For wooden wall mounting, you can just use the
self-tapping screw to fix the mounting base.
The wall must be strong enough to withstand more than 3
times of the weight of the camera and the bracket.
2. Fix the mounting bracket with the camera to the mounting
base.
Mounting base

Network Camera·Quick Operation Guide
6
6
Note: The “bottom” mark on the mounting base should align with
the “bottom” mark on the mounting bracket.
Figure 2-2 Fix the Camera
3. View the image of the camera over the network.
4. Loosen the screws on the bracket slightly.
Note:Please loosen the screws slightly until you can adjust the
camera and do not remove the screws from the bracket.
5. Adjust the camera to the desired surveillance angle and then
tighten the screws on bracket to fix the camera.
Figure 2-3 Adjust Monitoring Angle
Rotation screw
Panning screw
Tilting screw

Network Camera·Quick Operation Guide
7
7
6. Loosen the lock screw on the sun shield and move the sun
shield until you can remove it. Remove the sun shield.
Figure 2-4 Remove the Sun Shield
7. Rotate to remove the front cover from camera and adjust the
lens to get a clear image.
Figure 2-5 Adjust the Lens
Front
cover
Adjust the
lens

Network Camera·Quick Operation Guide
8
8
8. Fix the lens; reinstall the front cover and the sun shield to
finish the installation.
Note: Reinstall the front cover until aligning the mark on the front
cover with the mark on the camera.
Figure 2-6 Reinstall the Camera

Network Camera·Quick Operation Guide
9
9
3Setting the Network
Camera over the LAN
Purpose:
To view and configure the camera via LAN(Local Area Network),
you need to connect the network camera in the same subnet with
your PC. Then, install the SADP or iVMS-4200 software to search
and change the IP of network camera.
The following figure shows the cable connection of network
camera and PC:
Figure 3-1 Wiring over LAN
Set the IP address of the camera for accessing via LAN.
Steps:
1. To get the IP address, you can choose either of the following
methods:
Use SADP, a software tool which can automatically detect
network camera in the LAN and list the device information