HIK VISION DS-2CD7153 User manual

Network Camera
User Manual
V3.0.0
Hangzhou Hikvision Digital Technology Co., Ltd.
http://www.hikvision.com
Service Tel：[phone]
2010-04

Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
This manual applies to Network Camera.
This manual may contain several technical incorrect places or printing
errors, and the content is subject to change without notice. The
updates will be added to the new version of this manual. We will readily
improve or update the products or procedures described in the
manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or
reliability of the security or signaling aspects of this product. UL has only
tested for fire, shock or casualty hazards as outlined in UL’s Standard(s)
for Safety, UL60950-1. UL Certification does not cover the performance
or reliability of the security or signaling aspects of this product. UL
MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT.”

User Manual of Network Camera 1
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly
to avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards
to prevent serious injury or
death.
Cautions Follow these precautions
to prevent potential injury or
material damage.
Warnings：
1. In the use of the product, you must strictly comply with the electrical safety
regulations of the nation and region.
2. Source with DC 12V or AC 24V (Whether supporting AC 24V lies on the specific
camera model) according to the IEC60950－1 standard. Please refer to technical
specifications for more details.
3. Do not connect several devices to one power adapter as an adapter overload
may cause over-heating and can be a fire hazard. If use the POE as the power
supply, please make sure that the POE Switch have the sufficient
power .(Whether supporting PoE power supply lies on the specific camera
model)
4. Please make sure that the plug is firmly inserted into the power socket.
5. When the product is installed on a wall or ceiling, the device should be firmly
fixed.
6. If smoke, odor, or noise rise from the device, turn off the power at once and
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 2
unplug the power cable, then contact the service center.
7. If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 3
Notice:
1. Make sure the power supply voltage is correct before using the camera.
2. Do not drop the camera or subject it to physical shock.
3. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean
cloth with a bit of ethanol and wipe it gently. If the camera will not be used for
an extended period of time, put on the lens cap to protect the sensor from dirt.
4. Do not aim the camera at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
5. The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor will not be exposed to the
laser beam.
6. Do not place the camera in extremely hot or cold temperatures (the operating
temperature should be between -10°C~+60°C, dusty or damp locations, and do
not expose it to high electromagnetic radiation.
7. To avoid heat accumulation, good ventilation is required for a proper operating
environment.
8. While shipping, the camera should be packed in its original packing, or packing
of the same texture.
9. Regular part replacement: a few parts (e.g. electrolytic capacitor) of the
equipment should be replaced regularly according to their average life time.
The average time varies because of differences between operating
environment and usage history, so regular checking is recommended for all users.
Please contact with your dealer for more details.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©
4
Table of Contents
Chapter 1 Network Camera Connection......................................................1
Chapter 2 Network Access ..............................................................................3
2.1 Access over IE Browser..........................................................................3
2.1.1 Live View.........................................................................................4
2.1.2 Parameters Configuration............................................................7
2.2 Access over Client Software ............................................................. 19
2.2.1 Client Software Installation........................................................ 19
2.2.2 Live View...................................................................................... 21
2.2.3 Sensor Parameters Configuration............................................ 24
Chapter 3 Access over Internet ................................................................... 28
3.1 Access network camera with static IP....................................... 28
3.2 Access network camera with dynamic IP................................. 29
Appendix 1 SADP Introduction..................................................................... 33
Appendix 2 Port Map..................................................................................... 35
Appendix 3 Pin Definition............................................................................... 37

User Manual of Network Camera 1
Chapter 1 Network Camera
Connection
Two methods can be used to connect between network camera and PC, shown as
below:
Fig. 1.1 Cross Line Connection
Fig. 1.2 Direct Line Connection
Before visiting network camera over network, user should acquire its IP address first.
SADP is a software tool which can automatically detect Hikvision’s network device in
the LAN and give the device’s information like IP address, mask, port number,
device serial number, software version, etc., shown as Fig. 1.3.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 2
Fig.1.3
Select the device, and set its IP address and mask at the same network segment
with the PC.
For the detailed introduction of SADP, please refer to Appendix 1.
Note: The network camera is set with the factory default IP address of “192.0.0.64”,
the port of “8000”, the super user name of “admin” and the password of “12345”.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 3
Chapter 2 Network Access
After hardware installation, user can view live video and configure parameters for
the network camera, including IP address, subnet mask and port number, etc. The
following two methods can be used to access the camera:
1. View live video and configure parameters over IE browser.
2. View live video and configure parameters over client software.
2.1 Access over IE Browser
Before access to the camera over
IE browser, user should adjust the
security level.
Open the IE browser, and set the
security level to [Low] in [Tools/
InternetOptions/Security/Custom
Level...], and enable Activex
Control and Plug-in directly as
well.
Fig. 2.1.1 Adjust the Security Level
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 4
2.1.1 Live View
Figure 2.1.2 Tips of ActiveX Control Installation
Fig. 2.1.3 Install the ActiveX Control
Step 1: Install Active-X Control
and Plug-in.
Input the IP address of the
network camera and press
[Enter], then click the mention
box that pop up.
Step 3:
Step 2:
Click [Run] to install the ActiveX
control.
Input the “Username”
(default: admin), “Password”
(default: 12345) and “Port”
(default: 8000) of the
camera, and then click
[Login].
Fig. 2.1.4 Login Interface
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 5
Step 4:
After successful login, user is allowed to view the live video. Refer to Figure 2.1.5.
Fig. 2.1.5 Live View Page
Icons on Live View Page:
Icon Description
Full-screen display mode
Exit full-screen display mode
Start Preview
Stop Preview
Capture Picture
Start/Stop Record
DigitalZoom
Video Parameters
Digital Zoom:
Click mouse in the desired position of live video image and scroll the mouse to
realize zoom in and zoom out function.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 6
Video Parameters:
Fig. 2.1.6 Video Parameters
Icon Description
Brightness: 0~100 configurable
Contrast: 0~100 configurable
Saturation: 0~100 configurable
Hue: 0~100 configurable
Gain: 0~100 configurable
Exposure time: 0~40000
configurable
Restore default
Fig.2.1.7PTZControl
PTZ Control:
Click PTZ tag in the main interface of
the live view page to enter the PTZ
control panel shown in Fig. 2.1.7, and
re-clicking PTZ tag again will hide the
panel.
Use the directional buttons to control
the pan/tilt movement, and drag the
slide bar to adjust the speed from
level 1 to 7, with the default speed of
level 4.
Click button to start auto scan,
and re-click it to stop scan.
Click the functional buttons to realize
zoom, focus and iris control.
Select a preset number and click
button to call preset.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 7
2.1.2 Parameters Configuration
Click Configuration to enter the Parameters Configuration interface.
2.1.2.1 Local Configuration
Fig. 2.1.8 Local Configuration
Local Configuration:
Parameters Description
Protocol type TCP and UTP selectable
Stream type Main stream and Sub stream selectable
Display mode Full-screen, 4:3 mode, 16:9 mode or adjustable to resolution
Package file size 128M, 256M, 512M selectable
Transmission
performance
Shortest delay mode, good real-time, normal real-time and fluency
and good fluency options selectable
Save record file as The default directory for saving record files is C: \OCXRecordFiles,
which can be modified by user
Save captured
picture as
The default directory for saving captured files is
C:\OCXBMPCaptureFiles, which can be modified by user
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 8
2.1.2.2 Remote Configuration
Fig.2.1.9BasicInformation
Basic Information：
In the Basic Information
settings interface, user is
allowed to set the Device
Name and Device ID, as
well as view the
information of IP camera,
including Device
Description, Device
Location, MAC address,
Device Type, Device SN,
Firmware Version, and
U-boot Version.
Fig.2.1.10DisplaySettings
Channel
ParametersDisplay
Setting:
According to different
requirements, enable the
display of Date & Time
and Week by clicking the
checkbox.
Different date formats
can be selected.
The OSD Status can be set
to transparent & flickering,
transparent & unflickering,
nontransparent &
flickering, or
nontransparent &
unflickering.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 9
Fig.2.1.11VideoSettings
Channel ParametersVideo Settings:
Parameter Description
Stream type Select stream type to Main stream or Sub stream
Resolution Select the resolution for your need,
Image Quality Select image quality to Highest, High, Medium, Low, Lower or Lowest
Stream Type Select the bitrate type to Constant bitrate or Variable bitrate
Max. Bitrate Select or custom bitrate according to the resolution
Multicast Set the multicast address, with the default multicast of 0.0.0.0
RTSP Port Set the RTSP port, with the default RTSP port of 554
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 10
Fig. 2.1.12 Motion Detection Zone Settings
Fig. 2.1.13 Motion Detection Linkage Settings
Channel
ParametersMotion
Detection Setting:
Select the checkbox of
Enable motion detection
to enable this function.
Zone Settings:
Click Start draw button to
draw motion detection
zone by clicking and
dragging the mouse in
the live video image.
User is allowed to draw
multiple motion detection
zones in the same picture.
When all zones have been
set, click Stop draw to
finish drawing.
Sensitivity:
The sensitivity level can be
set to 0, 1, 2, 3, 4 and 5.
When it is set to 0, the
sensitivity is disabled.
Linkage:
The Linkage method can
be selected to either
Email link or Trigger alarm
output.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 11
Fig.2.1.14TextOverlaySettings
Channel ParametersText
Overlay Setting:
Input the characters in the
Text Information box and
define the OSD location in
the image by setting the
XPosition and YPosition,
and then select the
checkbox of OSD Text.
After clicking Save to finish
the settings, the defined
title will be displayed on
the image.
Note:
The values of XPosition and
YPosition refer to the
position relative to the
origin as the upper left
corner of the image.
Network
ParametersNetwork
Setting:
Set the IP Address, Subnet
Mask, Gateway and DNS
Server of the network
camera.
Fig.2.1.15NetworkSettings
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 12
Fig. 2.1.16 PPPOE Settings
Network
ParametersPPPOE
Setting:
Click the checkbox of
Enable PPPOE to enable
this function.
Input the PPPOE user
name and password in
the text box and then
click Save to finish
settings. After reboot, the
camera will obtain a
public IP address.
Network
ParametersDDNS
Setting:
Click the checkbox of
Enable DDNS to enable
this function.
The protocol type can be
set to DynDNS or IPServer.
Fig. 2.1.17 DDNS Settings
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 13
Fig. 2.1.18 DynDNS Settings
If the protocol type is
selected to DynDNS,
please input the Server
Address, e.g.,
members.dyn dns. org.
The User Name and
Password refer to the user
name and password
registered in the DynDNS
website.
The Device Name refers
to the domain name
applied in the DynDNS
website.
If the protocol type is
selected to IPServer,
please input the Server
Address of the IPServer.
Fig. 2.1.19 IPServer Settings
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©

User Manual of Network Camera 14
Fig.2.1.20 NTP Settings
Network
ParametersDDNS
Setting:
Click the checkbox of
Enable NTP to enable this
function. Input the Server
Address and Port of NTP.
If the public network is
applied, please input the
NTP Server Address with
provision of time sync
service, e.g.,
210.72.145.44.
In the private network is
applied, the NTP software
can be used to establish
NTP server to achieve time
synchronization.
Fig.2.1.21E-mailSettings
Network
ParametersE-mail
Setting:
Through E-mail settings, the
alarm message can be
sent to the designated
E-mail address when alarm
event occurs.
Input the SMTP server, SMTP
port, user name, password,
E-mail sender and receiver,
and finally click Save to
finishE-mailsettings.
Hangzhou Hikvision Digital Technology Co., Ltd. | Copyright ©