HIK VISION HiLook IPC-B149H User manual

0
Quick Start Guide
Network Bullet Camera

Network Bullet Camera·Quick Start Guide
1
Quick Start Guide
©2020 Hangzhou Hikvision Digital Technology Co., Ltd.
All Rights Reserved
Any and all information, including, among others, wordings, pictures,
graphs are the properties of Hangzhou Hikvision Digital Technology
Co., Ltd. or its subsidiaries (hereinafter referred to be "Hikvision").
This user manual (hereinafter referred to be "the Manual") cannot be
reproduced, changed, translated, or distributed, partially or wholly,
by any means, without the prior written permission of Hikvision.
Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the
Manual.
About this Manual
Pictures, charts, images and all other information hereinafter are for
description and explanation only. The information contained in the
Manual is subject to change, without notice, due to firmware updates
or other reasons. Please find the latest version in the company
website (http://www.hikvision.com).
Please use this user manual under the guidance of professionals.
Trademarks
and other Hikvision's trademarks and logos are the
properties of Hikvision in various jurisdictions. Other trademarks and
logos mentioned below are the properties of their respective owners.
Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

Network Bullet Camera·Quick Start Guide
2
FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION, MERCHANTABILITY,
SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION,
ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO
YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT
DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF
BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS
PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS
PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT
THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information

Network Bullet Camera·Quick Start Guide
3
FCC Information
Please take attention that changes or modification not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
FCC compliance: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.

Network Bullet Camera·Quick Start Guide
4
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info
2006/66/EC (battery directive): This product contains
a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the
product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your supplier
or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards
requirements.

Network Bullet Camera·Quick Start Guide
5
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into "Warnings" and "Cautions"
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
●Proper configuration of all passwords and other security settings
is the responsibility of the installer and/or end-user.
●In the use of the product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
●The power source should meet limited power source or PS2
requirements according to IEC 60950-1 or IEC 62368-1 standard.
Warnings
Cautions
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

Network Bullet Camera·Quick Start Guide
6
●Do not connect several devices to one power adapter as adapter
overload may cause over-heating or a fire hazard.
●Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
●If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the service center.
Cautions
●CAUTION: Hot parts! Burned fingers when handling the parts.
Wait one-half hour after switching off
before handling parts. This sticker is to
indicate that the marked item can be hot
and should not be touched without taking care. For device with
this sticker, this device is intended for installation in a restricted
access location, access can only be gained by service persons or
by users who have been instructed about the reasons for the
restrictions applied to the location and about any precautions
that shall be taken.
●Make sure the power supply voltage is correct before using the
camera.
●Do not drop the camera or subject it to physical shock.
●Do not touch sensor modules with fingers. If cleaning is
necessary, use clean cloth with a bit of ethanol and wipe it

Network Bullet Camera·Quick Start Guide
7
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
●Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
●The sensor may be burned out by a laser beam, so when any
laser equipment is in using, make sure that the surface of sensor
will not be exposed to the laser beam.
●Do not place the camera in extremely hot, cold (the operating
temperature shall be -30°C to 60°C), dusty or damp locations,
and do not expose it to high electromagnetic radiation.
●To avoid heat accumulation, good ventilation is required for
operating environment.
●Keep the camera away from liquid while in use.
●While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
●Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average enduring time. The average time
varies because of differences between operating environment
and using history, so regular checking is recommended for all the
users. Please contact with your dealer for more details.
●This equipment is not suitable for use in locations where
children are likely to be present.

Network Bullet Camera·Quick Start Guide
8
●CAUTION: Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions
ATTENTION: IL Y A RISQUE D'EXPLOSION SI LA BATTERIE EST
REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE
AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX
INSTRUCTIONS
●Improper replacement of the battery with an incorrect type may
defeat a safeguard (for example, in the case of some lithium
battery types).
●Do not dispose of the battery into fire or a hot oven, or
mechanically crush or cut the battery, which may result in an
explosion.
●Do not leave the battery in an extremely high temperature
surrounding environment, which may result in an explosion or
the leakage of flammable liquid or gas.
●Do not subject the battery to extremely low air pressure, which
may result in an explosion or the leakage of flammable liquid or
gas.
●If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or
maintenance.)

Network Bullet Camera·Quick Start Guide
9
Table of Contents
1 Appearance Description ............................................................... 10
2 Installation.................................................................................... 15
Memory Card Installation.............................................. 15
Ceiling Mounting........................................................... 16
Mounting with Junction Box.......................................... 19
Install Network Cable Waterproof Jacket ...................... 22
3 Activate and Access Network Camera .......................................... 24

Network Bullet Camera·Quick Start Guide
10
1Appearance Description
Type I:
1
2
4
3
Type I Bullet Camera Overview
Description
No.
Description
1
Lens
2
Front Cover
3
Back Cover
4
Fix Ring
5
Power Cord
6
Network Cable

Network Bullet Camera·Quick Start Guide
11
Type II:
2
5
4
3
1
Type II Bullet Camera Overview
Description
No.
Description
1
Lens
2
Front Cover
3
MIC
4
Back Cover
5
Mounting Base
6
Power Cord
7
Network Cable

Network Bullet Camera·Quick Start Guide
12
Type III:
1
2
5
4
3
Type III Bullet Camera Overview
Description
No.
Description
1
Lens
2
Front Cover
3
Memory Card Slot Cover
4
Back Cover
5
Mounting Base
6
Power Cord
7
Network Cable

Network Bullet Camera·Quick Start Guide
13
Type IV:
DC
1
2
V
I
N
1
2
3 4
5
Bullet Camera Overview
Description
No.
Description
1
Lens
2
Main Body
3
Bracket
4
Power Cord
5
Network Cable

Network Bullet Camera·Quick Start Guide
14
Type V:
1
2
34
5
DC12
V
I
N
Bullet Camera Overview
Description
No.
Description
1
Lens
2
Main Body
3
Bracket
4
Power Cord
5
Network Cable
Note:
For cameras support power over Ethernet (PoE), the power is passed
along with data on Ethernet cabling. And a switch supports PoE
function is required.

Network Bullet Camera·Quick Start Guide
15
2Installation
Before you start:
●Make sure the device in the package is in good condition and all
the assembly parts are included.
●The standard power supply is PoE or 12 VDC, please make sure
your power supply matches with your camera.
●Make sure all the related equipment is power-off during the
installation.
●Check the specification of the products for the installation
environment.
●Make sure that the wall is strong enough to withstand four times
the weight of the camera and the bracket.
●Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing reflection.
Memory Card Installation
Only type III camera supports memory card installation, you can
follow the steps to mount and unmount the memory card.
Steps:
1. Loosen the screws to remove the memory card slot cover.

Network Bullet Camera·Quick Start Guide
16
Unscrew the Cover and Insert Memory Card
2. Insert the memory card into the memory card slot.
3. (Optional) To unmount the memory card, push to get it ejected.
4. Screw the cover back to the camera.
Ceiling Mounting
Before you start:
Both wall mounting and ceiling mounting are suitable for the bullet
camera. Ceiling mounting will be taken as an example in this section.
And you can take steps of ceiling mounting as a reference for wall
mounting.
This camera series shares a similar structure, and type IV camera is
used for demonstration.
Steps:
1. Paste the drill template (supplied) to the desired mounting position
on the ceiling/wall.
2. Drill the screw holes in the ceiling/wall according to the supplied
drill template.

Network Bullet Camera·Quick Start Guide
17
Note:
Drill the cable hole, if adopting ceiling outlet to route the cable.
3-Ø 4 mm (0.2")
Cable Hole
Side
Opening
Screw Hole
template
Ø55 mm (2.2")
Ø68 mm (2.7")
Ø18 mm (0.7")
Figure 2-2 The Drill Template
3. Route the cables through the cable hole (optional), or the side
opening.
4. Fix the camera on the ceiling/wall with supplied screws.
Figure 2-3 Fix the Camera on the Ceiling/Wall

Network Bullet Camera·Quick Start Guide
18
Note:
In the supplied screw package, both self-tapping screws, and
expansion bolts are contained.
If the ceiling is cement, expansion bolts are required to fix the
camera. If the ceiling is wooden, self-tapping screws are required.
5. Connect the corresponding power cord and network cable.
6. Power on the camera, and set the network configuration (for
details, refer to 3 Activate and Access Network Camera) to check
whether the image is gotten from the optimum angle. If not, adjust
the viewing angle.
1) Loosen the No.1 adjusting screw to adjust the rotation
position [0° to 360°].
2) Tighten the No.1 adjusting screw.
3) Loosen the No.2 adjusting screw to adjust the tilting position
[-90° to 90°].
4) Tighten the No. 2 adjusting screw.
5) Loosen the No.3 fix ring to adjust the pan position [0° to
360°].
6) Tighten the No.3 fix ring.
Note:
For some camera models, the tilting adjusting angle is 0°to 90°.

Network Bullet Camera·Quick Start Guide
19
R: 0°to
360°
T: -90°to 90°
P: 0°to 360°
3
2
1
Figure 2-4 3-aix Adjustment
7. (Optional) Install the waterproof jacket. Refer to 2.4 Install Network
Cable Waterproof Jacket for details.
Mounting with Junction Box
Before you start:
Both wall mounting and ceiling mounting are suitable for the bullet
camera. Wall mounting will be taken as an example in this section.
And you can take steps of wall mounting as a reference for ceiling
mounting.
You need to purchase a junction box first.
Steps:
1. Paste the drill template (supplied) to the desired mounting position
on the wall/ceiling.
2. Drill the screw holes and the cable hole (optional) in the
wall/ceiling according to the drill template.