HIK VISION DS-2CE1582P-VFIR3 User manual

High-definition IR Water-proof
Bullet Camera
User Manual
UD.6L0201D0086A01

High-definition IR Water-proof Bullet Camera·User Manual
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual applies to
DS-2CE1582P (N)-VFIR3
DS-2CC1283P-VFIR3
DS-2CC1283P-AVFIR3
DS-2CC1281P (N)-VFIR3
DS-2CC1281P (N)-AVFIR3
DS-2CC12A1P (N)-VFIR3
DS-2CC12A1P (N)-AVFIR3
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.”
0100001030320

High-definition IR Water-proof Bullet Camera·User Manual
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

High-definition IR Water-proof Bullet Camera·User Manual
3
3
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For more
information see: www.recyclethis.info

High-definition IR Water-proof Bullet Camera·User Manual
4
4
Table of Contents
1 Introduction ........................................................................6
1.1 Product Features ......................................................6
1.2 Overview .................................................................7
2 Installation..........................................................................8
2.1 Ceiling Mounting ......................................................8
2.2 Power Supply ......................................................... 12
3 Menu Description (A) .......................................................14
3.1 Menu Overview ...................................................... 14
3.2 Exposure................................................................ 15
3.3 Color...................................................................... 22
3.4 Day & Night ........................................................... 23
3.5 Function.................................................................26
3.6 Motion ................................................................... 28
3.7 Privacy................................................................... 30
3.8 Setup..................................................................... 33
3.9 System .................................................................. 36
3.10 Exit ...................................................................... 37
4 Menu Description (B) .......................................................38
4.1 Main Menu ............................................................. 38
4.2 Lens Settings ......................................................... 39
4.3 Shutter/AGC Settings ............................................. 41
4.4 White Balance Settings........................................... 43
4.5 Backlight Settings .................................................. 47
4.6 Picture Adjust Settings ........................................... 47
4.7 ATR Settings .......................................................... 49
4.8 Motion Detection Settings ....................................... 50
4.9 Privacy Mask Settings............................................. 52

High-definition IR Water-proof Bullet Camera·User Manual
5
5
4.10 Day/Night Settings ............................................... 53
4.11 NR Settings .......................................................... 56
4.12 Camera ID Settings .............................................. 56
4.13 SYNC Settings ...................................................... 58
4.14 Language Settings................................................ 59
4.15 Camera Reset Settings ......................................... 59
4.16 Pixel Correct Settings ........................................... 59
4.17 Save All/Exit ........................................................ 60

High-definition IR Water-proof Bullet Camera·User Manual
6
6
1Introduction
1.1 Product Features
This camera adopts a high-sensitivity sensor and advanced circuit
design technology. It possesses features of high resolution, low
image distortion and low noise, which are suitable for surveillance
system and image processing system.
Adopt high-performance sensor, and w ith a high resolution
which brings high-quality images.
High co lor rendition with Auto White Balance function.
High S/N ratio which makes the image is vivid and clear.
Support Auto Electronic Shutter control to adapt to different
environments.
Support auto gain control to adapt to changing light conditions.
Support Backlight Compensation (BLC), which can adjust the
iris so that the object in the sensitive area is properly exposed.
Bullet camera adopts an advanced product design and the
mounts of them support wiring out from inside.
Adopt unique two-shell design which can ensure the senor has
a proper temperature to get a high quality image.
Ingress Protection level reaches IP66.

High-definition IR Water-proof Bullet Camera·User Manual
7
7
1.2 Overview
Figure 1-1 Overview
Bracket
Mounting Base
Power Cable
Video Cable
Zoom
Focus

High-definition IR Water-proof Bullet Camera·User Manual
8
8
2Installation
Before you start:
Read the following contents carefully before the installation.
Make sure that all the related equipment is power-off during
the installation.
Check the specification of the products for the installation
environment.
Check whether the power supply is matched w ith your AC
outlet to avoid damage.
If the product does not function properly, please contact your
dealer or the nearest service center. Do not disassemble the
camera for repair or maintenance by yourself.
Ceiling mounting is recommended, we will take ceiling mounting
as an example to explain the installation steps in this chapter.
2.1 Ceiling Mounting
Notes:
1. When mounting the camera, for the cement wall, you need to
mount the base with expansion screws. For the wooden wall,
you need to mount the base with self-tapping screws.
2. Please ensure that the wall is strong enough to withstand more
than 3 times the weight of the camera and the bracket. If the
wall is not strong enough, the camera may fall and cause
serious damage.

High-definition IR Water-proof Bullet Camera·User Manual
9
9
3. Before any operation, please make sure that the device in the
package is in good condition and all the assembly parts are
completed.
Steps:
1. Drill the holes on the wall with the supplied drilling template.
2. Route the cables inside the ceiling or on the surface. If you
want to route the cables inside the ceiling, drill the cable hole in
the ceiling for wiring; pull all cables through the hole and
terminate all wires (if not yet terminated).
3. Connect the power cable and video cable and secure the
mounting base w ith camera to the wall with supplied screws.
Figure 2-1 Secure the Camera
4. Three-axis adjustment.
1). Preview the image of the camera on a monitor.
Wall

High-definition IR Water-proof Bullet Camera·User Manual
10
10
Note: You must loosen the lock screw or fixed ring before
adjustment and tighten it when you adjusted it.
2). Rotate the panning table to adjust the panning position of
the camera. The adjustable range is from 0 degree to 360
degrees.
3). Rotate the tilting table to adjust the tilting position of the
camera. The adjustable range is from 0 degree to 75
degrees.
4). Rotate the lens to adjust the azimuth angle of the image.
The adjustable range is from 0 degree to 360 degrees.
Figure 2-2 Adjust the Azimuth Angle
5. To focus and zoom, adjust the FOCUS and ZOOM screws on the
camera to get a clear image.
Pan: 0~360°
Lock screw
Lock screw
Rotation: 0~360°
Tilt: 0~90°

High-definition IR Water-proof Bullet Camera·User Manual
11
11
Figure 2-3 Adjust the Lens
Focus
Zoom

High-definition IR Water-proof Bullet Camera·User Manual
12
12
2.2 Power Supply
Figure 2-4 Power Cable (Round Interface)
Note: Please make sure the power adapter is match with the
camera, the standard adapter model for camera is DC12V (Please
refer to technical specifications for more details).

High-definition IR Water-proof Bullet Camera·User Manual
13
13
Figure 2-5 Power Cable (Two-needle Interface )
Note: Please make sure that the power adapter is match with the
camera. The standard power supply of the camera is usually 12V
DC or 24V AC (Please refer to technical specifications for more
details).

High-definition IR Water-proof Bullet Camera·User Manual
14
14
3Menu Description (A)
Note: This Menu only works for DS-2CC1283P-VFIR3, and
DS-2CC1283P-AVFIR3.
3.1 Menu Overview
This series of camera supports OSD menu, the main menu is listed
as below:
Table 3-1 Main Menu
Main
Menu
EXPOSURE
LENS, HBLC/D-WDR, AGC, 3D-DNR,
SENSE UP
COLOR
WB MODE, R-Y GAIN, B-Y GAIN
DAY &NIGHT
DAY&NIGHT MODE, A_SUP, C_SUP
FUNCTION
MIRROR, SHARPNESS, MONITOR,
GAMMA,LSC
MOTION
MOTION, AREA SEL, SENSITI, DISPLAY,
HOLD TIME, ALARM.
PRIVACY
MASK1~MASK8
SETUP
TITLE, MANUAL DPC, AUTO DPC, OLPF,
OSD COLOR
SYSTEM
CAMERA ID, COMMUNI, LANGUAGE
EXIT
FACTORY SET, SAVE&EXIT, EXIT

High-definition IR Water-proof Bullet Camera·User Manual
15
15
3.2 Exposure
Purpose:
Exposure is realized by Shutter/IRS/Gain control. On the Exposure
menu, you can configure the LENS, HBLC/D-WDR, AGC, 3D
DNR, SENSE-UP settings. See Figure 3-1.
EXPOSURE
LENS ELC
HBLC/D-WDR BLC
AGC HIGH
3D DNR AUTO
SENSE-UP AUTO
EXIT RETURN↓
Figure 3-1 Exposure Menu
Lens
You can set the Lens to ELC mode or DC mode.
ELC Mode
In the ELC Mode, auto shutter has a higher priority to auto
iris. E.SHUTTER value can be configured to AUTO(default),
x2, x4, x8, x16, x32, x64, x128, x256, x512, x1024,1/50,
1/100, 1/120FLK, 1/250, 1/500, 1/1K,1/2K, 1/4K, 1/10K
and 1/100K (second).
BRIGHT refers to the brightness of the image, in ELC mode,
the image brightness is controlled by shutter. You can set

High-definition IR Water-proof Bullet Camera·User Manual
16
16
the value from 1 to 100. 50 is the default value. See Figure
3-2.
LENS-ELC
E.SHUTTER AUTO
BRIGHT 028 ---|----
RETURN↓
Figure 3-2 ELC Mode
DC Mode
In DC Mode, auto iris has a higher priority to auto shutter.
AUTO, x2, x4, x8, x16, x32, x64, x128, x256, x512,
x1024,1/50, 1/100, 1/120FLK, 1/250, 1/500, 1/1K, 1/2K,
1/4K,1/10K,1/100K (second) are selectable for
E.SHUTTER.
BRIGHT of the image is controlled by iris in DC mode, and
the value can be set from 1 to 100.
DC REF means the reference value of the iris. The bigger
the value you set, the higher the brightness reference value
is. You can set the value from 0 to 20. See Figure 3-3.

High-definition IR Water-proof Bullet Camera·User Manual
17
17
LENS-DC
E.SHUTTER AUTO
BRIGHT 028---|-----
DC REF 010---|-----
RETURN↓
Figure 3-3 DC Mode
HBLC/D-WDR
Note: This item contains BLC, HLI, and D-WDR function.
BLC (Backlight Compensation)
If there’s a strong backlight, the object in the foreground
appears silhouetted or dark. BLC can correct the exposure
of the subject.
BLC supports AUTO mode and Manual mode.In the Auto
mode, the areas are not configurable, and in the manual
mode, you can set the area size and coordinate by changing
the value of its up/down/left/right. See Figure 3-4 and
Figure 3-5.
BLC level can be adjusted by WEIGHT in the BLC menu;
you can set it to OFF, LOW, MID, and HIGH.

High-definition IR Water-proof Bullet Camera·User Manual
18
18
BLC
BLC MODE MANUAL
BLC WEIGHT MID
RETURN ↓
Figure 3-4 BLC
BLC-MANUAL
TOP 006--|-------
BOTTOM 012----|-----
LEFT 004-|--------
RIGHT 011---|------
RETURN↓
Figure 3-5 BLC Area Set
HLI (Highlight Inverse)
Highlight inverse is a function which inverses the area
which is strongly- highlighted. The HLI BLC mode is
controlled by BLC window area (HBLC). You can set the
inverse area by changing the value of its top/bottom/left/
right. And you can also set the BLC level to OFF, LOW, MID,
HIGH. See Figure 3-6.

High-definition IR Water-proof Bullet Camera·User Manual
19
19
HBLC
BLC LEVEL OFF
TOP 006 --|--------
BUTTOM 012---|--------
LEFT 004--|--------
RIGHT 011---|--------
RETURN ↓
Figure 3-6 HBLC
Mode
ALL DAY and NIGHT are selectable. All day means HLI
function will be effective for both day and night, and Night
means it only takes effect in night mode.
Set Level
It’s the value boundary for HLI function. The HLI function
will be performed if it reaches the value you set. The value
can be set from 0 to 255.
Gray Mode
Black, Gray, and D.Gray are selectable to deal with the
images which are over the value you set for HLI. See Figure
3-7.