HIK VISION DS-2CE16D0T-WL3 User manual

TURBO HD
TVI Bullet Camera
User Manual
UD04876B
User Manual
Thank you for purchasing our product. If there are any
questions, or requests, do not hesitate to contact the
dealer.
This manual applies to the model listed below.
Type
Model
Type I
DS-2CE16D0T-WL3
Type II
DS-2CE16D0T-WL5
This manual may contain several technically incorrect
places or printing errors, and the content is subject to
change without notice. The updates will be added to the
new version of this manual. We will readily improve or
update the products or procedures described in the
manual.
0100001070302

Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation
EU Conformity Statement
This product and - if applicable - the
supplied accessories too are marked with
"CE" and comply therefore with the
applicable harmonized European standards
listed under the EMC Directive 2014/30/EU, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A)
standards requirements.

Safety Instruction
These instructions are intended to ensure that user can
use the product correctly to avoid danger or property
loss.
The precaution measure is divided into “Warnings” and
“Cautions”
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any
of the cautions are neglected.
Warnings
In the use of the device, you must be in strict
compliance with the electrical safety regulations of the
nation and region.
Input voltage should meet both the SELV (Safety Extra
Low Voltage) and the Limited Power Source with 12
VDC according to the IEC60950-1 standard. Refer to
technical specifications for detailed information.
Do not connect multiple devices to one power adapter
to avoid over-heating or a fire hazard caused by
overload.
Make sure that the plug is firmly connected to the
power socket.
Make sure that the device is firmly fixed if wall
mounting or ceiling mounting is adopted.
If smoke, odor or noise rise from the device, turn off
the power at once and unplug the power cord, and
then contact the service center.
Never attempt to disassemble the camera by
unprofessional personal.
Cautions
Do not drop the camera or subject it to physical shock.
Do not touch senor modules with fingers.
If cleaning is necessary, use clean cloth with a bit of
ethanol and wipe it gently.
Do not aim the camera at the sun or extra bright places.
The sensor may be burned out by a laser beam, so
when any laser equipment is in using, make sure that
the surface of sensor will not be exposed to the laser
beam.
Do not expose the device to high electromagnetic
radiation or extremely hot, cold, dusty or damp
environment.
To avoid heat accumulation, good ventilation is
required for the operating environment.
Keep the camera away from liquid while in use for non-
water-proof device.
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

While in delivery, the camera shall be packed in its
original packing, or packing of the same texture.

Introduction
1.1 Product Features
The camera is applicable for outdoor conditions, and the
application scenarios include road, parking lot, campus,
etc..
The main features are as follows:
High performance CMOS sensor
1080p resolution
Auto white balance
Auto electronic shutter
Auto gain control (AGC)
White supplement light
Up the Coax (HIKVISION-C)
1.2 Overview
1.2.1 Type I Camera Overview
Switch Cable
TVI Video Cable
Power Cord
(12 VDC )
White
Supplement Light
Lens
Sun Shield
Figure 1. 1 Type I Camera Overview
1.2.2 Type II Camera Overview
TVI Video Cable
Power Cord
( 12 VDC)
White
Supplement Light
Sun Shield
White Supplement
Light
Lens
Switch Cable
Figure 1. 2 Type II Camera Overview
Installation
2.1 Installation Preparation
Before you start:
Make sure that the device in the package is in good
condition and all the assembly parts are included.
Make sure that all the related equipment is power-off
during the installation.
Check the specification of the products for the
installation environment.
Check whether the power supply is matched with your
power output to avoid damage.
Make sure the wall is strong enough to withstand three
times the weight of the camera and the bracket.
If the wall is cement, insert expansion bolts before you
install the camera. If the wall is wooden, use self-
tapping screws to secure the camera.
If the product does not function properly, contact your
dealer or the nearest service center. Do NOT

disassemble the camera for repair or maintenance by
yourself.
Note:
Since type I camera and type II camera share the same
installation method, we take type I camera as the
example to describe the installation.
2.2 Wall Mounting
Before you start:
The package contains the wall mounting bracket.
Steps:
1. Attach the bracket to the wall.
2. Mark the screw holes on the wall according to the
holes on the bracket.
3. Drill the screw holes.
4. Attach the bracket to the wall and secure the camera
with supplied screws.
Figure 2. 1 Secure the camera to the wall
Note:
In the supplied screw package, both self-tapping
screws and expansion bolts are contained.
If the wall is cement, expansion bolts are required to
fix the camera. If the wall is wooden, self-tapping
screws are required.
5. Align the camera to the pedestal, and secure the
camera on the pedestal with supplied screws.
Screw
Pedestal
Figure 2. 2 Secure the Camera on the Bracket
6. Route the cables and connect the corresponding
power cord and video cable.
7. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to
get an optimum angle.
1). Loosen the horizontal adjusting screw to adjust
the pan position (0°to 360°).
2). Tighten the horizontal adjusting screw.
3). Loosen the vertical adjusting screw to adjust the
tilt position (0°to 90°)
4). Tighten the vertical adjusting screw.

Horizontal Adjusting
Screw
Pan Position:
0° to 360°
Vertical Adjusting Screw
Tilt Position:
0° to 90°
Figure 2. 3 Angle Adjustment
2.3 Pendant Mounting
Before you start:
You need to purchase a pendant bracket first.
Steps:
1. Attach the bracket to the ceiling.
2. Mark the screw holes on the ceiling according to the
holes on the bracket.
3. Drill the screw holes.
4. Attach the bracket to the ceiling and secure the
camera with supplied screws.
Figure 2. 4 Fix the Bracket on the Ceiling
Note:
In the supplied screw package, both self-tapping
screws and expansion bolts are contained.
If the wall is cement, expansion bolts are required to
fix the camera. If the wall is wooden, self-tapping
screws are required.
5. Remove the screw on the top of the camera to
expose the screw hole.
Screw
Figure 2. 5 Remove the Screw
6. Align the screw hole on the top of the camera with
the pendant mounting bracket and rotate the camera
to get it fixed.

Adjusting Knob
Figure 2. 6 Fix the Camera to the Bracket
7. Route the cables and connect the corresponding
power cord and video cable.
8. Power on the camera to check whether the image on
the monitor is gotten from the optimum angle. If not,
adjust the camera according to the figure below to
get an optimum angle.
1). Loosen the adjusting knob to adjust the pan
position (0°to 360°) and tilt position (0°to 90°)
2). Tighten the adjusting knob.
Adjusting Knob
Tilt Position:
0° to 90°
Pan Position:
0° to 360°
Figure 2. 7 Angle Adjustment