HIKOKI G 12SA3 User manual

Disc Grinder
Model G 12SA3 • G 13SB3
Handling instructions
Note:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available as an
important reference when using this power tool.
G13SB3
0000BookG12SA3Eng.indb10000BookG12SA3Eng.indb1 2017/12/0515:13:232017/12/0515:13:23

GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to
power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
2
English
0000BookG12SA3Eng.indb20000BookG12SA3Eng.indb2 2017/12/0515:13:232017/12/0515:13:23

SAFETY WARNINGS COMMON FOR
GRINDING OR ABRASIVE CUTTING-OFF
OPERATIONS
a) This power tool is intended to function as a grinder
or cut-offtool. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
b) Operations such as sanding, wire brushing or
polishing are not recommended to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically
designed and recommended by the tool
manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated speed can
break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) The arbour size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle of
the power tool.
Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to high
intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fly away and cause injury beyond immediate area of
operation.
j) Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a”live” wire may make
exposed metal parts of the power tool “live” and shock
the operator.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the spinning
accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m) Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o) Do not operate the power tool near flammable
materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction
of the wheel’s movement at the point of pinching. Abrasive
wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a) Maintain a firm grip on the power tool and position
your body and arm to allow you to resist kickback
forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction
during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of control.
3
English
0000BookG12SA3Eng.indb30000BookG12SA3Eng.indb3 2017/12/0515:13:242017/12/0515:13:24

SAFETY WARNINGS SPECIFIC FOR GRINDING
AND ABRASIVE CUTTING-OFF OPERATIONS
a) Use only wheel types that are recommended for
your power tool and the specific guard designed for
the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power
tool and positioned for maximum safety, so the least
amount of wheel is exposed towards the operator.
The guard helps to protect the operator from broken
wheel fragments, accidental contact with wheel and
sparks that could ignite clothing.
c) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-offwheel.
Abrasive cut-offwheels are intended for peripheral
grinding, side forces applied to these wheels may cause
them to shatter.
d) Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing
the possibility of wheel breakage. Flanges for cut-off
wheels may be different from grinding wheel flanges.
e) Do not use worn down wheels from larger power
tools.
Wheel intended for larger power tool is not suitable for
the higher speed of a smaller tool and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC
FOR ABRASIVE CUTTING-OFF OPERATIONS
a) Do not “jam” the cut-offwheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut.
Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback or wheel breakage.
b) Do not position your body in line with and behind
the rotating wheel.
When the wheel, at the point of operation, is moving
away from your body, the possible kickback may propel
the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut
for any reason, switch offthe power tool and hold
the power tool motionless until the wheel comes to
a complete stop. Never attempt to remove the cut-
offwheel from the cut while the wheel is in motion
otherwise kickback may occur.
Investigate and take corrective action to eliminate the
cause of wheel binding.
d) Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter
the cut.
The wheel may bind, walk up or kickback if the power tool
is restarted in the workpiece.
e) Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kickback.
Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the
line of cut and near the edge of the workpiece on both
sides of the wheel.
f) Use extra caution when making a “pocket cut” into
existing walls or other blind areas.
The protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
GENERAL SAFETY INSTRUCTIONS FOR
GRINDERS
– Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder;
– Ensure that the wheel dimensions are compatible with
the grinder;
– Abrasive wheels shall be stored and handled with care in
accordance with manufacturer’s instructions;
– Inspect the grinding wheel before use, do not use
chipped, cracked or otherwise defective products;
– Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions;
– Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required;
– Ensure that the abrasive product is correctly mounted
and tightened before use and run the tool at no-load
for 30 s in a safe position, stop immediately if there is
considerable vibration or if other defects are detected.
If this condition occurs, check the machine to determine
the cause;
– If a guard is equipped with the tool never use the tool
without such a guard;
– Do not use separate reducing bushings or adapters to
adapt large hole abrasive wheels;
– For tools intended to be fitted with threaded hole wheel,
ensure that the thread in the wheel is long enough to
accept the spindle length;
– Check that the work piece is properly supported;
– Do not use cutting offwheel for side grinding;
– Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances;
– Ensure that ventilation openings are kept clear when
working in dusty conditions, if it should become
necessary to clear dust, first disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts;
– Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves, helmet
and apron should be worn;
– Pay attention to the wheel that continues to rotate after
the tool is switched off.
4
English
0000BookG12SA3Eng.indb40000BookG12SA3Eng.indb4 2017/12/0515:13:242017/12/0515:13:24

 Lubricate the sliding section of the set piece (B) and the
lever if the lever does not move smoothly.
Lever
Set piece (B)
M5 screw
Fig. 1
5. Ensure that mounted wheels and points are fitted in
accordance with the manufacturer’s instructions.
Ensure that the depressed center wheel to be utilized is
the correct type and free of cracks or surface defects.
Also ensure that the depressed center wheel is properly
mounted and the wheel nut is securely tightened, Refer
to the section on “ASSEMBLING AND DISASSEMBLING
THE DEPRESSED CENTER WHEEL”
Ensure that blotters are used when they are provided
with the bonded abrasive product and when they are
required.
Do not use separate reducing bushings or adaptors to
adapt large hole abrasive wheels.
For tools intended to be fitted with threaded hole wheel,
ensure that the thread in the wheel is long enough to
accept the spindle length.
Do not use cutting offwheel for side grinding.
6. Conducting a trial run
Ensure that the abrasive products is correctly mounted
and tightened before use and run the tool at no-load for
30 seconds in a safe position, stop immediately if there
is considerable vibration or if other defects are detected.
If this condition occurs, check the machine to determine
the cause.
7. Confirm the push button.
Confirm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on (See Fig. 3).
8. Fixing the side handle.
Screw the side handle into the gear cover.
9. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
SPECIFICATIONS
Model G12SA3 G13SB3
Rated voltage (by areas)* (110V, 120V, 127V, 220V, 230V, 240V)
Power input* 1300 W
No-load speed* 11000 /min
Wheel outer dia. × hole dia. 115 ×22.23 mm 125 ×22.23 mm
peripheral speed 80 m/s
Weight (only main body) 1.9 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Depressed center wheel ............................................. 1
(2) Wrench ....................................................................... 1
(3) Side handle................................................................. 1
Standard accessories are subject to change without
notice.
APPLICATIONS
 Removal of casting fin and finishing of various types of
steel, bronze and aluminum materials and castings.
 Grinding of welded sections or sections cut by means of
a cutting torch.
 Grinding of synthetic resins, slate, brick, marble, etc.
 Cutting of synthetic concrete, stone, brick, marble, and
similar materials.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
3. Extension cord
When the work area is removed from the power source,
use an extension cord of sufficient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Fitting and adjusting the wheel guard
The wheel guard is a protective device to prevent injury
should the depressed center wheel shatter during
operation. Ensure that the guard is properly fitted and
fastened before commencing grinding operation. By
slightly loosening the setting screw, the wheel guard
can be turned and set at any desired angle for maximum
operational effectiveness. Ensure that the setting screw
is thoroughly tightened after adjusting the wheel guard.
[In the case of Tool-less wheel guard] (Fig. 1)
 Set the wheel ass’y to the packing gland.
 Tighten M5 screw to secure the wheel guard while the
lever is in closed position.
 Perform the adjustment of the wheel guard while the
lever is released. (Loosen M5 screw and readjust if the
wheel guard does not rotate smoothly.)
 After adjustment, if grinder operation is required, perform
the operation only after setting the lever in closed
position.
5
English
0000BookG12SA3Eng.indb50000BookG12SA3Eng.indb5 2017/12/0515:13:242017/12/0515:13:24

PRACTICAL GRINDER APPLICATION
1. Pressure
To prolong the life of the machine and ensure a first
class finish, it is important that the machine should not
be overloaded by applying too much pressure. In most
applications, the weight of the machine alone is sufficient
for effective grinding. Too much pressure will result in
reduced rotational speed, inferior surface finish, and
overloading which could reduce the life of the machine.
2. Grinding angle
Do not apply the entire surface of the depressed center
wheel to the material to be ground. As shown in Fig. 2,
the machine should be held at an angle of 15° – 30° so
that the external edge of the depressed center wheel
contacts the material at an optimum angle.
15° – 30°
A B
Fig. 2
3. To prevent a new depressed center wheel from digging
into the workpiece, initial grinding should be performed
by drawing the grinder across the workpiece toward the
operator (Fig. 2 direction B). Once the leading edge of
the depressed center wheel is properly abraded, grinding
may be conducted in either direction.
4. Precautions immediately after finishing operation
The wheel continues to rotate after the tool is switched
off.
After switching offthe machine, do not put it down until the
depressed center wheel has come to a complete stop.
Apart from avoiding serious accidents, this precaution
will reduce the amount of dust and swarf sucked into the
machine.
CAUTION
Check that the work piece is properly supported.
Ensure that ventilation openings are kept clear when
working in dusty conditions.
If it should become necessary to clear dust, first
disconnect the tool from the mains supply (use non-
metallic objects) and avoid damaging internal parts.
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances.
Always use eye and ear protection.
Other personal protective equipment such as dust
mask, gloves, helmet and apron should be worn when
necessary.
If in doubt, wear the protective equipment.
When the machine is not use, the power source should
be disconnected.
ASSEMBLING AND DISASSEMBLING THE
DEPRESSED CENTER WHEEL (Fig. 3)
CAUTION: Be sure to switch OFF and disconnect the
attachment plug from the receptacle to avoid a
serious accident.
1. Assembling (Fig. 3)
(1) Turn the disc grinder upsidedown so that the spindle is
facing upward.
(2) Align the across flats of the wheel washer with the
notched part of the spindle, then attach them.
(3) Fit the protuberance of the depressed center wheel onto
the wheel washer.
(4) Screw the wheel nut onto the spindle.
(5) While pushing the push button with one hand, lock the
spindle by turning the depressed center wheel slowly
with the other hand.
Tighten the wheel nut by using the supplied wrench as
shown in Fig. 3.
Wrench
Wheel nut
Depressed
center wheel
Wheel washer
Wheel guard
Spindle
Push button
Diamond wheel
Fig. 3
2. Disassembling
Follow the above procedures in reverse.
CAUTION
Confirm that the depressed center wheel is mounted
firmly.
Confirm that the push button is disengaged by pushing
push button two or three times before switching the
power tool on.
MAINTENANCE AND INSPECTION
1. Inspecting the depressed center wheel
Ensure that the depressed center wheel is free of cracks
and surface defects.
2. Inspecting the mounting screws:
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
3. Inspecting the carbon brushes (Fig. 4)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brush with a new one having the same carbon brush No.
shown in the figure when it becomes worn to or near the
“wear limit”. In addition, always keep carbon brushes
clean and ensure that they slide freely within the brush
holders.
6
English
0000BookG12SA3Eng.indb60000BookG12SA3Eng.indb6 2017/12/0515:13:242017/12/0515:13:24

6mm
88
17mm
Wear limit
No. of carbon brush
Fig. 4
4. Replacing carbon brushes (Fig. 5)
<Disassembly>
(1) Loosen the D4 tapping screw retaining the tail cover and
remove the tail cover.
(2) Use the auxiliary hexagonal wrench or small screwdriver
to pull up the edge of the spring that is holding down the
carbon brush. Remove the edge of the spring toward the
outside of the brush holder.
(3) Remove the end of the pig-tail on the carbon brush from
the terminal section of brush holder and then remove the
carbon brush form the brush holder.
<Assembly>
(1) Insert the end of the pig-tail of the carbon brush in the
terminal section of brush holder.
(2) Insert the carbon brush in the brush holder.
(3) Use the auxiliary hexagonal wrench or small screwdriver
to return the edge of the spring to the head of the carbon
brush.
(4) Mount the tail cover and tighten the D4 tapping screw.
Spring
Carbon brush Brush holder
Fig. 5
5. Replacing supply cord
If the replacement of the supply cord is necessary, this
has to be done by the manufacturer of this agent in order
to avoid a safety hazard.
6. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool. Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
7. Service parts list
A: Item No.
B: Code No.
C: No. Used
D: Remarks
CAUTION
Repair, modification and inspection of HiKOKI Power
Tools must be carried out by an HiKOKI Authorized
Service Center.
This Parts List will be helpful if presented with the tool to
the HiKOKI Authorized Service Center when requesting
repair or other maintenance.
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
MODIFICATIONS
HiKOKI Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts (i.e. code numbers and/or
design) may be changed without prior notice.
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
7
English
0000BookG12SA3Eng.indb70000BookG12SA3Eng.indb7 2017/12/0515:13:242017/12/0515:13:24

8
G12SA3
ABC D
1 320-523 4 D5 × 25 2 325-053 1 3 301-944 1 4 321-737 1 "3, 19" 5 949-558 1 M8 6 308-541 1 7 308-543 1 8 980-866 1 9 629-T12 1
629T12DDC3PS2-L
10 957-754 1 11 321-734 1 12 360-734E 1 230V – 240V 13 321-732 1 14 982-021 2 D4 × 70
15-1 340-645E 1 230V 15-2 340-645F 1 240V
16 315-877 1 17 608-VVM 1 608VVC2PS2L 18 303-255 2 M4 × 10 19 301-943 1 20 321-736 1 21 991-207 3 M4 × 8 22 936-680 1 23 620-1DD 1
6201DDCMPS2L
24 308-546 1 25 308-545 1 26 307-046 4 M5 × 16 27 944-109 1 3 × 3 × 8 28 994-301 1 29 949-241 1 M5 × 20 30 949-454 1 M5 31 319-656 1 "29, 30" 32 937-928Z 1
ABC D
33 316-821 1 115MM A36Q 34 994-324 1 M14 35 321-735 1 "6, 20" 36 314-428 1 37 325-050 1 38 321-733 1 39 319-319 1 40 325-055 1 41 325-051 1 42 999-088 2 43 317-810 2 44 308-536 2 45 325-054 1 46 980-063 2 47 984-750 2 D4 × 16 48 937-631 1 49 953-327 1 5 0 ––––––––––– 1 51 301-815 2 D4 × 45 52 325-058 1 53 325-052 1 54 ––––––– 1
501 938-332Z 1
502-1 994-322 1 502-2 325-496 1
0000BookG12SA3Eng.indb80000BookG12SA3Eng.indb8 2017/12/0515:13:252017/12/0515:13:25

9
G13SB3
ABC D
1 320-523 4 D5 × 25 2 325-053 1 3 301-944 1 4 321-737 1 "3, 19" 5 949-558 1 6 308-541 1 7 308-543 1 8 980-866 1 9 629-T12 1
629T12DDC3PS2-L
10 957-754 1 11 321-734 1
12-1 360-734C 1 110V 12-2 360-734E 1 230V – 240V
13 321-732 1 14 982-021 2 D4 × 70
15-1 340-645C 1 110V 15-2 340-645E 1 230V 15-3 340-645F 1 240V
16 315-877 1 17 608-VVM 1 608VVC2PS2L 18 303-255 2 M4 × 10 19 301-943 1 20 321-736 1 21 991-207 3 M4 × 8 22 936-680 1 23 620-1DD 1
6201DDCMPS2L
24 308-546 1 25 308-545 1 26 307-046 4 M5 × 16 27 944-109 1 3 × 3 × 8 28 994-301 1 29 949-241 1 M5 × 20 30 949-454 1 M5
31-1 320-192 1 "29, 30" 31-2 311-742 1 "35-40"
ABC D
32 937-817Z 1 33 316-821 1
125MM A36Q
34 994-324 1 M14 35 311-492 1 36 311-744 1 37 311-743 1 38 880-734 1 M5 × 25 39 311-491 1 40 874-759 1 41 321-735 1 "6, 20" 42 314-428 1 43 325-050 1 44 321-733 1 45 319-319 1 46 325-055 1 47 325-051 1 48 999-088 2 49 317-810 2 50 308-536 2 51 325-054 1 52 980-063 2 53 984-750 2 D4 × 16 54 937-631 1 55 953-327 1 5 6 ––––––––––– 1 57 301-815 2 D4 × 45 58 325-058 1 59 325-052 1 60 ––––––– 1
501 938-332Z 1 502 956-633 1
0000BookG12SA3Eng.indb90000BookG12SA3Eng.indb9 2017/12/0515:13:252017/12/0515:13:25

10
0000BookG12SA3Eng.indb100000BookG12SA3Eng.indb10 2017/12/0515:13:252017/12/0515:13:25

11
0000BookG12SA3Eng.indb110000BookG12SA3Eng.indb11 2017/12/0515:13:252017/12/0515:13:25

806
Code No. C99143612 M
Printed in Malaysia
Shinagawa Intercity Tower A, 15-1, Konan 2-chome,
Minato-ku, Tokyo, Japan
0000BookG12SA3Eng.indb120000BookG12SA3Eng.indb12 2017/12/0515:13:262017/12/0515:13:26