HIKOKI SP 18VA User manual

Handling instructions
ﺔﺟﻟﺎﻌﻣﻟﺍ ﺕﺎﻣﻳﻠﻌﺗ
en
ar
SP 18VA
en
ar
0000BookSP18VA.indb10000BookSP18VA.indb1 2018/05/1510:15:402018/05/1510:15:40

2
English
Carrying power tools with your finger on the switch
or energising power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power toolʼs operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a)
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
PRECAUTION
Keep children and infirm persons away.
When not in use, tools should be stored out of reach of
children and infirm persons.
GENERAL POWER TOOL SAFETY
WARNINGS
WARNING
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the offposition before connecting to
power source and/or battery pack, picking up or
carrying the tool.
0000BookSP18VA.indb20000BookSP18VA.indb2 2018/05/1510:15:402018/05/1510:15:40

3
English
SAFETY WARNINGS COMMON
FOR SANDING OR POLISHING
OPERATIONS
a) This power tool is intended to function as a sander
or polisher. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
b) Operations such as grinding, wire brushing or
cutting-offare not recommended to be performed
with this power tool.
Operations for which the power tool was not designed
may create a hazard and cause personal injury.
c)
Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
Just because the accessory can be attached to your
power tool, it does not assure safe operation.
d)
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
e) The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories cannot be adequately
guarded or controlled.
f) Threaded mounting of accessories must match the
grinder spindle thread. For accessories mounted
by flanges, the arbour hole of accessory must fit
the locating diameter of the flange.
Accessories that do not match the mounting hardware of
the power tool will run out of balance, vibrate excessively
and may cause loss of control.
g) Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires.
If power tool or accessory is dropped, inspect for
damage or install an undamaged accessory. After
inspecting and installing an accessory, position
yourself and bystanders away from the plane of
the rotating accessory and run the power tool at
maximum no-load speed for one minute.
Damaged accessories will normally break apart during
this test time.
h)
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of
stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping flying
debris generated by various operations. The dust mask
or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to
high intensity noise may cause hearing loss.
i) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment.
Fragments of workpiece or of a broken accessory may
fly away and cause injury beyond immediate area of
operation.
j)
Hold the power tool by insulated gripping surfaces
only, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make
exposed metal parts of the power tool “live” and could
give the operator an electric shock.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged and your
hand or arm may be pulled into the spinning accessory.
l) Never lay the power tool down until the accessory
has come to a complete stop.
The spinning accessory may grab the surface and pull
the power tool out of your control.
m)
Do not run the power tool while carrying it at your side.
Accidental contact with the spinning accessory could
snag your clothing, pulling the accessory into your body.
n) Regularly clean the power tool’s air vents.
The motor’s fan will draw the dust inside the housing and
excessive accumulation of powdered metal may cause
electrical hazards.
o)
Do not operate the power tool near flammable materials.
Sparks could ignite these materials.
p) Do not use accessories that require liquid coolants.
Using water or other liquid coolants may result in
electrocution or shock.
KICKBACK AND RELATED
WARNINGS
Kickback is a sudden reaction to a pinched or snagged
rotating wheel, backing pad, brush or any other accessory.
Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool
to be forced in the direction opposite of the accessory’s
rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by
the workpiece, the edge of the wheel that is entering into the
pinch point can dig into the surface of the material causing
the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of
the wheel’s movement at the point of pinching.
Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
a)
Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
b) Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c) Do not position your body in the area where power
tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or
kickback.
e) Do not attach a saw chain woodcarving blade or
toothed saw blade.
Such blades create frequent kickback and loss of control.
SAFETY WARNINGS SPECIFIC FOR
SANDING OPERATIONS
a) Do not use excessively oversized sanding disc
paper. Follow manufacturers recommendations,
when selecting sanding paper.
Larger sanding paper extending beyond the sanding pad
presents a laceration hazard and may cause snagging,
tearing of the disc or kickback.
0000BookSP18VA.indb30000BookSP18VA.indb3 2018/05/1510:15:402018/05/1510:15:40

4
English
SAFETY WARNINGS SPECIFIC FOR
POLISHING OPERATIONS
a) Do not allow any loose portion of the polishing
bonnet or its attachment strings to spin freely. Tuck
away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
PRECAUTIONS ON USING
ELECTRONIC SANDER POLISHER
1. Never mount a grinding wheel and attempt to use this
tool as a disc grinder.
2. Always hold the body handle and side handle of the
power tool firmly.
Otherwise the counterforce produced may result in
inaccurate and even dangerous operation.
3. Ensure that sparks resulting from use do not create
a hazard e. g. do not hit persons, or ignite flammable
substances.
4. Always use protective safety glasses and hearing
protectors, use other personal protective equipment
such as gloves, apron and helmet when necessary.
5. Always use eye and ear protection.
Other personal protective equipment such as dust
mask, gloves, helmet and apron should be worn when
necessary.
If in doubt, wear the protective equipment.
6. Mounting the sanding disc and wool bonnet.
○Improper fitting of the wool bonnet may cause vibration.
○Use a wrench to tighten the washer nut sufficiently.
○After releasing the lock pin, check to be sure that it has
returned to its normal position.
7. RCD
The use of a residual current device with a rated residual
current of 30 mA or less at all times is recommended.
SYMBOLS
WARNING
The following show symbols used for the machine.
Be sure that you understand their meaning before
use.
SP18VA: Electronic Sander Polisher
To reduce the risk of injury, user must read
instruction manual.
Always wear eye protection.
V Rated voltage
Alternating current
/min Revolution or reciprocations per minute
Switching ON
Switching OFF
Disconnect mains plug from electrical outlet
Warning
Class II tool
STANDARD ACCESSORIES
In addition to the main unit (1 unit), the package
contains the accessories listed in the below.
(1) Rubber Pad .................................................................1
(2) Loop Handle (with bolt and washer) ............................1
(3) Bar Wrench .................................................................1
Standard accessories are subject to change without notice.
APPLICATIONS
○Grinding metal surfaces
○Preliminary sanding of metal surfaces before painting,
rust removal, removing old paint before repainting.
○Finishing woodwork, correcting projections of timber
from joints or assemblies.
○Preliminary sanding of wood surfaces before applying
paint.
○Polishing or shining painted metal surfaces, such as
those of automobiles, trains, elevators, refrigerators,
sewing machines, washing machines, metal appliances,
etc.
○Polishing varnished surfaces of wooden furniture, etc.
○Shining synthetic resin or ebonite products.
SPECIFICATIONS
Voltage (by areas)* (110 V, 120 V, 220 V,
230 V, 240 V)
Power input 1250 W*
No load speed 0 – 3400 /min
Rated Speed 3750 /min
Sanding Disc Size outer dia. ×
inner dia. 180 × 22 mm
Weight (without cord, standard
accessories) 2.8 kg
* Be sure to check the nameplate on product as it is subject
to change by areas.
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
MOUNTING AND OPERATION
Action Figure Page
Attachment of a loop handle 1 10
Assembling sanding disc 2 10
Assembling wool bonnet 3 10
Switch operation and variable
speed operation 410
Sander operation 5 11
Replacing carbon brush 6 11
Selecting accessories ―12
0000BookSP18VA.indb40000BookSP18VA.indb4 2018/05/1510:15:402018/05/1510:15:40

5
English
Motor speed can be variable as desired by rotating the dial;
it is increased by turning the dial towards “6”, decreased by
turning it towards “1”.
Select the motor speed appropriate for the work being done.
The following table gives the motor speeds corresponding
to each indication on the dial scale and shows the types of
work for which they are suitable.
Dial
Indication R.P.M. Type of work
1 600
For Polishing
2 1100
3 1700
4 2300
5 2900 For Sanding
6 3400
CAUTION
The dial cannot be rotated further than the “6” or “1” on
the scale in their respective directions.
Sander operation
(1) This unit is designed to provide sufficient polishing
(sanding) power with the disc pressed lightly against
the sanding/polishing surface: it is equipped with an
electronic control circuit to ensure that the motor will
not slow down even when loaded. There is therefore no
need to press the sanding disc hard against the surface;
doing so can overload the motor, subsequently causing
the overload cut device to step into operation by cutting
the motor’s power supply.
If this should happen, cut the power switch and turn at
the correct motor speed.
(2) Do not apply the entire disc surface to the surface of
the material. As shown in Fig. 5, the sander should be
held at an approximately 15° to 25° angle in relation to
the material surface so that the peripheral portion of the
sanding disc is offered to the material surface.
(3) Precaution immediately after finishing an operation:
After turning the switch OFF, do not put the sander down
until the sanding disc has come to a complete stop. This
precaution will not only prevent a serious accident, but
will also reduce the amount of dust and swarf sucked into
the machine.
Polisher operation
(1) Curved surfaces as well as flat surfaces can be efficiently
finished. Do not excessively push the polisher against
the surface of the material. The weight of the polisher
alone is sufficient for effective polishing. Excessive
pressure will result in a poor finish and cause possible
overload to the motor.
(2) Sanding disc, polishing compound or wax should be
selected in accordance with the material and the desired
surface finish. Maximum polishing effect will be attained
by following the following method:
○Preliminary polishing with sander using a finegrain
sanding disc.
○Polishing with wool bonnet using polishing compound
and/or wax. Apply a small quantity of compound and/or
wax on material surface and polish with the wool bonnet.
CAUTION
○Carefully guard against permitting the cabtyre cord to
touch the wool bonnet or sanding disc during operation.
If the cord touches, there is a danger that it may become
entangled.
○Do not use the lock pin as a brake to stop the tool as this
may lead to damage of the gear or detachment of the
tool.
MAINTENANCE AND INSPECTION
1. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
2. Inspecting the carbon brushes (Fig. 6)
The motor employs carbon brushes which are
consumable parts. Since an excessively worn carbon
brush can result in motor trouble, replace the carbon
brushes with new ones having the same carbon brush
No. ⓐshown in the figure when it becomes worn to or
near the “wear limit” ⓑ. In addition, always keep carbon
brushes clean and ensue that they slide freely within the
brush holders.
3. Replacing a carbon brush (Fig. 6)
Disassemble the brush cap with a minus-head
screwdriver. The carbon brush can then be easily
removed.
4. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
5. Cleaning lock pin section
If the lock pin section becomes dirty, clean it at once.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
NOTE
Due to HiKOKI’s continuing program of research and
development, the specifications herein are subject to
change without prior notice.
0000BookSP18VA.indb50000BookSP18VA.indb5 2018/05/1510:15:412018/05/1510:15:41

6
٤
ﺓﺭﻔﻧﺻﻟﺍ ءﺩﺑ
ﻊﻣ (ﺓﺭﻔﻧﺻﻟﺍ) ﻝﻘﺻﻠﻟ ﺔﻳﻓﺎﻛ ﺔﻗﺎﻁ ﺭﻳﻓﻭﺗﻟ ﺓﺩﺣﻭﻟﺍ ﻩﺫﻫ ﻡﻳﻣﺻﺗ ﻡﺗ
(1)
ﻲﻫﻭ :ﺓﺭﻔﻧﺻﻟﺍ / ﻝﻘﺻﻟﺍ ﺢﻁﺳ ﻩﺎﺟﺗﺍ ﻲﻓ ﻕﻓﺭﺑ ﻁﻭﻐﺿﻣﻟﺍ ﺹﺭﻘﻟﺍ
ﺩﻧﻋ ﻰﺗﺣ ﻙﺭﺣﻣﻟﺍ ءﺎﻁﺑﺇ ﻡﺩﻋ ﻥﺎﻣﺿﻟ ﺔﻳﻧﻭﺭﺗﻛﻟﺇ ﻡﻛﺣﺗ ﺓﺭﺋﺍﺩﺑ ﺓﺯﻬﺟﻣ
ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﻰﻠﻋ ﻁﻐﺿﻠﻟ ﺔﺟﺎﺣ ﻙﺎﻧﻫ ﺱﻳﻟ ﻲﻟﺎﺗﻟﺎﺑﻭ .ﻪﻳﻠﻋ ﻝﻳﻣﺣﺗﻟﺍ
ﺩﺋﺍﺯﻟﺍ ﻝﻳﻣﺣﺗﻟﺍ ﻰﻟﺇ ﻱﺩﺅﻳ ﻥﺃ ﻥﻛﻣﻳ ﻙﻟﺫﺑ ﻡﺎﻳﻘﻟﺍ .ﺢﻁﺳﻟﺍ ﻩﺎﺟﺗﺍ ﻲﻓ ﺓﻭﻘﺑ
ﻊﻁﻘﻟﺍ ﺯﺎﻬﺟ ﻰﻠﻋ ﺩﺋﺍﺯﻟﺍ ﻝﻳﻣﺣﺗﻟﺍ ﻲﻓ ﺏﺑﺳﺗﻳ ﻲﻟﺎﺗﻟﺎﺑﻭ ،ﻙﺭﺣﻣﻟﺍ ﻰﻠﻋ
ﻲﻓ ﺔﻗﺎﻁﻟﺍ ﺕﺍﺩﺍﺩﻣﺇ ﻊﻁﻗ ﻕﻳﺭﻁ ﻥﻋ ﻝﻳﻐﺷﺗﻟﺍ ﻊﺿﻭ ﻲﻓ ﻝﻭﺧﺩﻠﻟ
.ﻙﺭﺣﻣﻟﺍ
ﻙﺭﺣﻣﻟﺍ ﺔﻋﺭﺳ ﻰﻟﺇ ﻝﻭﺣﺗﻟﺎﺑ ﻡﻗﻭ ﺔﻗﺎﻁﻟﺍ ﺡﺎﺗﻔﻣ ﻝﺻﻓﺍ ،ﻙﻟﺫ ﺙﺩﺣ ﺍﺫﺇ
.ﺔﺣﻳﺣﺻﻟﺍ
ﻲﻓ ﺢﺿﻭﻣ ﻭﻫ ﺎﻣﻛ .ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳﻟ ﻪﻠﻣﻛﺄﺑ ﺹﺭﻘﻟﺍ ﺢﻁﺳ ﻡﺩﺧﺗﺳﺗ ﻻ
(2)
ﺎًﺑﻳﺭﻘﺗ ﺔﺟﺭﺩ 25 ﻰﻟﺇ 15 ﺔﻳﻭﺍﺯﺑ ﺓﺭﻔﻧﺻﻟﺍ ﻝﻣﺣ ﻡﺗﻳ ﻥﺍ ﺏﺟﻳ ،5ﻝﻛﺷﻟﺍ
ﺹﺭﻘﻟ ﺔﻳﻁﻳﺣﻣﻟﺍ ﺔﺑﺳﻧﻟﺍ ﺽﺭﻋ ﻡﺗﻳ ﻙﻟﺫﻟ ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳﺑ ﻕﻠﻌﺗﻳ ﺎﻣﻳﻓ
.ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳ ﻰﻠﻋ ﺓﺭﻔﻧﺻﻟﺍ
ﻻ،ﺡﺎﺗﻔﻣﻟﺍ ﻝﻳﻐﺷﺗ ﻑﺎﻘﻳﺈﺑ ﻡﻭﻘﺗ ﻥﺃ ﺩﻌﺑ :ﻝﻳﻐﺷﺗﻟﺍ ﺩﻌﺑ ﺎﻣ ﺕﺎﻁﺎﻳﺗﺣﻻﺍ
(3)
ﻊﻧﻣﻳ ﻥﻟ .ﺎًﻣﺎﻣﺗ ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﻑﻗﻭﺗﻳ ﻰﺗﺣ ﻝﻔﺳﻷﺎﺑ ﺓﺭﻔﻧﺻﻟﺍ ﻊﺿﺗ
ﺭﺎﺑﻐﻟﺍ ﺔﻳﻣﻛ ﻝﻠﻘﻳ ﻑﻭﺳ ﻥﻛﻟﻭ ،ﺏﺳﺣﻓ ﺓﺭﻁﺧﻟﺍ ﺙﺩﺍﻭﺣﻟﺍ ﻁﺎﻳﺗﺣﻻﺍ ﺍﺫﻫ
.ﺔﻟﻵﺍ ﻲﻓ ﺔﺻﺗﻣﻣﻟﺍ ﺓﺩﺍﺭﺑﻟﺍﻭ
ﻝﻘﺻﻟﺍ ﺓﺍﺩﺃ ﻝﻳﻐﺷﺗ
ﻻ.ﺓءﺎﻔﻛﺑ ﺎﻬﻠﻘﺻ ﻥﻛﻣﻳ ﺔﻳﻭﺗﺳﻣﻟﺍ ﺢﻁﺳﻷﺍ ﺎًﺿﻳﺃﻭ ﺔﻳﻧﺣﻧﻣﻟﺍ ﺢﻁﺳﻷﺍ
(1)
ﻝﻘﺻﻟﺍ ﺓﺍﺩﺃ ﻥﺯﻭ ﻲﻔﻛﻳ .ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳ ﻝﺑﺎﻘﻣ ﻲﻓ ﻝﻘﺻﻟﺍ ﺓﺍﺩﺃ ﺹﺭﻗ ﻊﻓﺩﺗ
ﻰﻟﺇ ﺩﺋﺍﺯﻟﺍ ﻁﻐﺿﻟﺍ ﻱﺩﺅﻳ ﻑﻭﺳ .ﻝﺎﻌﻓ ﻝﻘﺻ ﻰﻠﻋ ﻝﻭﺻﺣﻠﻟ ﺎﻫﺩﺣﻭ
.ﻙﺭﺣﻣﻟﺍ ﻰﻠﻋ ﻝﻣﺣﻟﺍ ﻲﻓ ﺔﻧﻛﻣﻣ ﺓﺩﺎﻳﺯ ﻲﻓ ﺏﺑﺳﺗﻳﻭ ﻑﻳﻌﺿ ﻝﻘﺻ
ﺎًﻘﻓﻭ ﻊﻣﺷﻟﺍ ﻭﺃ ﻊﻳﻣﻠﺗﻟﺍ ﺏﻛﺭﻣﻭ ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﺩﻳﺩﺣﺗ ﻡﺗﻳ ﻥﺃ ﺏﺟﻳ
(2)
ﺩﺣﻟﺍ ﻰﻠﻋ ﻝﻭﺻﺣﻟﺍ ﻡﺗﻳ ﻑﻭﺳ .ﺏﻭﻏﺭﻣﻟﺍ ﺢﻁﺳﻟﺍ ﻝﻘﺻﻭ ﺓﺩﺎﻣﻠﻟ
:ﺔﻳﻟﺎﺗﻟﺍ ﺔﻘﻳﺭﻁﻟﺍ ﻉﺎﺑﺗﺍ ﻝﻼﺧ ﻥﻣ ﻝﻘﺻﻠﻟ ﻰﺻﻗﻷﺍ
ﺕﺎﺑﻳﺑﺣﻟﺍ ﻭﺫ ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﻡﺍﺩﺧﺗﺳﺎﺑ ﺓﺭﻔﻧﺻﻟﺍ ﻊﻣ ﻱﺩﻳﻬﻣﺗﻟﺍ ﻝﻘﺻﻟﺍ
○
.ﺔﻘﻳﻗﺩﻟﺍ
ﻡﺩﺧﺗﺳﺍ .ﻊﻣﺷﻟﺍ ﻭﺃ/ﻭﻊﻳﻣﻠﺗﻟﺍ ﺏﻛﺭﻣ ﻡﺍﺩﺧﺗﺳﺎﺑ ﻲﻓﻭﺻﻟﺍ ءﺎﻁﻐﻟﺍ ﻊﻳﻣﻠﺗ
○
ﻊﻳﻣﻠﺗﺑ ﻡﻗﻭ ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳ ﻰﻠﻋ ﻊﻣﺷﻟﺍ ﻭﺃ/ﻭﺏﻛﺭﻣﻟﺍ ﻥﻣ ﺓﺭﻳﻐﺻ ﺔﻳﻣﻛ
.ﻲﻓﻭﺻﻟﺍ ءﺎﻁﻐﻟﺍﻪﻳﺑﻧﺗ
ءﺎﻁﻐﻟﺍ ﺱﻣﻠﺑ (cabtyre) ﺭﻳﺎﺗﺑﺎﻛﻟﺍ ﻙﻠﺳﻟ ﺡﺎﻣﺳﻟﺍ ﻥﻣ ﺔﻳﺎﻧﻌﺑ ﺭﺫﺣﺍ
○
ﻙﺎﻧﻬﻓ ،ﻙﻠﺳﻟﺍ ﺱﻣﻻ ﺍﺫﺇ .ﻝﻳﻐﺷﺗﻟﺍ ءﺎﻧﺛﺃ ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﻭﺃ ﻲﻓﻭﺻﻟﺍ
.ﻙﺑﺎﺷﺗ ﺙﻭﺩﺣ ﺭﻁﺧ
ﻑﻠﺗ ﯽﻟﺇ ﻱﺩﺅﻳ ﺩﻗ ﻙﻟﺫ ﻥﻷ ﺓﺍﺩﻷﺍ ﻑﺎﻘﻳﻹ ﺢﺑﺎﻛﮐ ﻝﻔﻘﻟﺍ ﻥﺳ ﻡﺩﺧﺗﺳﺗ ﻻ
○
.ﺓﺍﺩﻷﺍ ﻝﺎﺻﻔﻧﺍ ﻭﺃ ﺱﺭﺗﻟﺍ
ﺹﺣﻔﻟﺍﻭ ﺔﻧﺎﻳﺻﻟﺍ
ﺕﻳﺑﺛﺗﻟﺍ ﺭﻳﻣﺎﺳﻣ ﺹﺣﻓ
1
ﺎﻬﻁﺑﺭ ﻡﺎﻛﺣﺇ ﻥﻣ ﺩﻛﺄﺗﻟﺍﻭ ﺕﻳﺑﺛﺗﻟﺍ ﺭﻳﻣﺎﺳﻣ ﺔﻓﺎﻛﻟ ﻱﺭﻭﺩﻟﺍ ﺹﺣﻔﻟﺎﺑ ﻡﻗ
.ﺭﻭﻔﻟﺍ ﻰﻠﻋ ﺎﻬﻁﺑﺭ ﻡﺎﻛﺣﺈﺑ ﻡﻗ ،ﺭﻳﻣﺎﺳﻣ ﺔﻳﺃ ﻙﻓ ﺔﻟﺎﺣ ﻲﻓ .ﺢﻳﺣﺻ ﻝﻛﺷﺑ
.ﺭﻁﺎﺧﻣ ﻰﻟﺇ ﻙﻟﺫﺑ ﻡﺎﻳﻘﻟﺍ ﻲﻓ ﻝﺷﻔﻟﺍ ﺽﺭﻌﻳ ﺩﻘﻓ
(6ﻝﻛﺷﻟﺍ) ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﺹﺣﻓ
2
.ﺓﺭﻣﻌﻣ ﺭﻳﻏ ءﺍﺯﺟﻷﺍ ﻥﻣ ﻲﻫﻭ ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻙﺭﺣﻣﻟﺍ ﻡﺩﺧﺗﺳﻳ
ﻝﻛﺎﺷﻣ ﺩﻭﺟﻭ ﻪﻧﻋ ﺞﺗﻧﻳ ﺩﻗ ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻝﻛﺂﺗ ﻥﻷ ﺍًﺭﻅﻧ
ﻡﻗﺭ ﺱﻔﻧ ﺎﻬﻳﺩﻟ ﺓﺩﻳﺩﺟ ﻯﺭﺧﺄﺑ ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻝﺍﺩﺑﺗﺳﺎﺑ ﻡﻗ ،ﻙﺭﺣﻣﻟﺎﺑ
ﻥﻣ ﺎﻬﺑﺍﺭﺗﻗﺍ ﻭﺃ ﺎﻬﻠﻛﺂﺗ ﺩﻧﻋ ﻝﻛﺷﻟﺍ ﻲﻓ ﺢﺿﻭﻣﻟﺍ ⓐ.ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ
ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻑﻳﻅﻧﺗﺑ ﻡﻗ ،ﻙﻟﺫ ﻰﻟﺇ ﺔﻓﺎﺿﻹﺎﺑ .ⓑ"ﻝﻛﺂﺗﻟﺍ ﺩﺣ"
.ﺓﺎﺷﺭﻔﻟﺍ ﺽﺑﺎﻘﻣ ﻝﺧﺍﺩ ﺔﺳﻼﺳﺑ ﺎﻬﻗﻻﺯﻧﺍ ﻥﻣ ﺩﻛﺄﺗﻟﺍﻭ ﺭﺍﺭﻣﺗﺳﺎﺑ
(6ﻝﻛﺷﻟﺍ) ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻝﺍﺩﺑﺗﺳﺍ
3
ﻉﺯﻧ ﻥﻛﻣﻳ ﻙﻟﺫ ﺩﻌﺑﻭ .ﺓﺭﻳﻐﺻ ﺱﺃﺭ ﻭﺫ ﻙﻔﻣﺑ ﺓﺎﺷﺭﻔﻟﺍ ءﺎﻁﻏ ﻙﻔﺑ ﻡﻗ
.ﺔﻟﻭﻬﺳﺑ ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ
ﻙﺭﺣﻣﻟﺍ ﺔﻧﺎﻳﺻ
4
.ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻥﻣ "ﻁﺳﻭﻷﺍ ءﺯﺟﻟﺍ" ﻭﻫ ﻙﺭﺣﻣﻟﺍ ﺓﺩﺣﻭ ﻑﻠﻣ
.ءﺎﻣﻟﺍ ﻭﺃ ﺕﻳﺯﻟﺍ ﺔﻁﺳﺍﻭﺑ ﻪﻠﻠﺑ ﻭﺃ/ﻭﻑﻠﻣﻟﺍ ﻑﻠﺗ ﻡﺩﻋ ﻥﻣ ﺭﺍﺭﻣﺗﺳﺎﺑ ﺩﻛﺎﺗ
ﻝﻔﻘﻟﺍ ﻥﺳ ﻊﻁﻘﻣ ﻑﻳﻅﻧﺗ
5
.ﺓﺩﺣﺍﻭ ﺓﺭﻣ ﻪﻔﻳﻅﻧﺗﺑ ﻡﻗ ،ﺎًﺧﺳﺗﻣ ﻝﻔﻘﻟﺍ ﻥﺳ ﻊﻁﻘﻣ ﺢﺑﺻﺃ ﺍﺫﺇ
ﻪﻳﺑﻧﺗ
ﺕﺎﻣﻳﻠﻌﺗ ﻉﺎﺑﺗﺍ ﺏﺟﻳ ،ﺎﻬﺗﻧﺎﻳﺻ ﻭﺃ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ ﺔﻟﺎﺣ ﻲﻓ
.ﺔﻟﻭﺩ ﻝﻛﺑ ﺔﺻﺎﺧﻟﺍ ﺭﻳﻳﺎﻌﻣﻟﺍﻭ ﻥﺎﻣﻷﺍ
ﺔﻅﺣﻼﻣ
ﺕﺎﻔﺻﺍﻭﻣﻟﺍ ﺭﻳﻐﺗﺗ ،ﺭﻣﺗﺳﻣﻟﺍ ﺭﻳﻭﻁﺗﻟﺍﻭ ﺙﺣﺑﻠﻟ HiKOKI ﺞﻣﺎﻧﺭﺑﻟ ﺎًﻌﺑﺗ
.ﻕﺑﺳﻣ ﻡﻼﻋﺇ ﻥﻭﺩ ﺎﻧﻫ ﺓﺭﻭﻛﺫﻣﻟﺍ
0000BookSP18VA.indb60000BookSP18VA.indb6 2018/05/1510:15:412018/05/1510:15:41

7٣
ﻻًﻼﺛﻣﻓ ﺍًﺭﻁﺧ ﺏﺑﺳﺗ ﻻﻡﺍﺩﺧﺗﺳﻻﺍ ﻥﻋ ﺔﺟﺗﺎﻧﻟﺍ ﺕﺍﺭﺍﺭﺷﻟﺍ ﻥﺃ ﻥﻣ ﺩﻛﺄﺗ
3
.ﻝﺎﻌﺗﺷﻼﻟ ﺔﻠﺑﺎﻗ ﺩﺍﻭﻣ ﺏﻧﺎﺟﺑ ﺎﻬﻠﻌﺷﺗ ﻭﺃ ﺹﺎﺧﺷﺄﺑ ﻡﺩﻁﺻﺗ
ﺓﺯﻬﺟﻷﺍ ﻡﺩﺧﺗﺳﺍﻭ ،ﺔﻳﻌﻣﺳﻟﺍ ﺕﺎﻳﻗﺍﻭﻟﺍﻭ ﺔﻳﺋﺎﻗﻭﻟﺍ ﻥﺎﻣﻻﺍ ﺕﺍﺭﺎﻅﻧ ﻡﺩﺧﺗﺳﺍ
4
ﺭﺯﺋﻣﻟﺍﻭ ﺕﺍﺯﺎﻔﻘﻟﺍ ﻝﺎﺛﻣﻟﺍ ﻝﻳﺑﺳ ﻰﻠﻋ ﻯﺭﺧﻷﺍ ﺔﻳﺻﺧﺷﻟﺍ ﺔﻳﺋﺎﻗﻭﻟﺍ
.ﺓﺭﻭﺭﺿﻟﺍ ﺩﻧﻋ ﺓﺫﻭﺧﻟﺍﻭ
.ﻥﺫﻷﺍﻭ ﻥﻳﻌﻟﺍ ﻲﻗﺍﻭ ﺎًﻣﺋﺍﺩ ﻡﺩﺧﺗﺳﺍ
5
ﺔﺑﺭﺗﻷﺍ ﻥﻣ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ﻝﺛﻣ ﻯﺭﺧﻷﺍ ﺔﻳﺋﺎﻗﻭﻟﺍ ﺕﺍﺩﻌﻣﻟﺍ ءﺍﺩﺗﺭﺍ ﺏﺟﻳ
.ﺓﺭﻭﺭﺿﻟﺍ ﺩﻧﻋ ﺭﺯﺋﻣﻟﺍﻭ ﺓﺫﻭﺧﻟﺍﻭ ﺕﺍﺯﺎﻔﻘﻟﺍﻭ
.ﺔﻳﺎﻗﻭﻟﺍ ﺕﺍﺩﻌﻣ ءﺍﺩﺗﺭﺎﺑ ﻡﻗ ،ﺩﻛﺄﺗﻟﺍ ﻡﺩﻋ ﺔﻟﺎﺣ ﻲﻓ
.ﺎﻣﻬﻛﻓﻭ ﻲﻓﻭﺻﻟﺍ ءﺎﻁﻐﻟﺍﻭ ﺓﺭﻔﻧﺻﻟﺍ ﺹﺭﻗ ﺏﻳﻛﺭﺗ
6
.ﺯﺍﺯﺗﻫﻻﺍ ﻲﻓ ﺏﺑﺳﺗﻳ ﺩﻗ ﻲﻓﻭﺻﻟﺍ ءﺎﻁﻐﻠﻟ ﺢﻳﺣﺻﻟﺍ ﺭﻳﻏ ﺕﻳﺑﺛﺗﻟﺍ
○
.ٍﻑﺎﻛ ٍﻝﻛﺷﺑ ﺓﺩﺭﻭﻟﺍ ﺔﻟﻭﻣﺎﺻ ﻁﺑﺭ ﻡﺎﻛﺣﻹ ﺡﺎﺗﻔﻣ ﻡﺩﺧﺗﺳﺍ
○
ﻪﻌﺿﻭ ﻰﻟﺇ ﺩﺎﻋ ﺩﻗ ﻪﻧﺃ ﻥﻣ ﺩﻛﺄﺗﻠﻟ ﻪﻧﻣ ﻕﻘﺣﺗ ،ﻝﻔﻘﻟﺍ ﻥﺳ ﺭﻳﺭﺣﺗ ﺩﻌﺑ
○
.ﻲﻌﻳﺑﻁﻟﺍ
RCD
7
ﺭﺎﻳﺗ ﻰﻠﻋ ﻱﻭﺗﺣﻳ ﻱﺫﻟﺍ ﻲﻘﺑﺗﻣﻟﺍ ﻲﺑﺭﻬﻛﻟﺍ ﺭﺎﻳﺗﻟﺍ ﻡﺍﺩﺧﺗﺳﺎﺑ ﻰﺻﻭﻳ
.ﺕﺎﻗﻭﻷﺍ ﻊﻳﻣﺟ ﻲﻓ ﻝﻗﺃ ﻭﺃ ﺭﻳﺑﻣﺃ 30 ﻥﻣ ﻥﻧﻘﻣ ﻲﺑﺭﻬﻛ
ﺯﻭﻣﺭﻟﺍ
ﺭﻳﺫﺣﺗ
ﺎﻫﺎﻧﻌﻣ ﻡﻬﻔﺗ ﻙﻧﺃ ﻥﻣ ﺩﻛﺄﺗ .ﺔﻧﻳﻛﺎﻣﻠﻟ ﺔﻣﺩﺧﺗﺳﻣﻟﺍ ﺯﻭﻣﺭﻟﺍ ﻲﻠﻳ ﺎﻣ ﻥﻳﺑﻳ
.ﻡﺍﺩﺧﺗﺳﻻﺍ ﻝﺑﻗ
ﺔﻳﻧﻭﺭﺗﻛﻟﻹﺍ ﺓﺭﻔﻧﺻﻟﺎﺑ ﻝﻘﺻﻟﺍ :SP18VA
ﻝﻳﻟﺩ ﺓءﺍﺭﻗ ﻡﺩﺧﺗﺳﻣﻟﺍ ﻰﻠﻋ ﺏﺟﻳ ،ﺔﺑﺎﺻﻹﺍ ﺭﻁﺧ ﻝﻳﻠﻘﺗﻟ
ﺕﺎﻣﻳﻠﻌﺗﻟﺍ
.ﻥﻳﻌﻠﻟ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ءﺍﺩﺗﺭﺎﺑ ﺎًﻣﺋﺍﺩ ﻡﻗ
V
ﻥﻧﻘﻣ ﻲﺑﺭﻬﻛ ﺩﻬﺟ
ﺩﺩﺭﺗﻣ ﺭﺎﻳﺗ
/min
ﺔﻘﻳﻗﺩﻟﺍ ﻲﻓ ﺔﻟﺩﺎﺑﻣ ﻭﺃ ﺓﺭﻭﺩ
(ON) ﻝﻳﻐﺷﺗﻟﺍ ﺡﺎﺗﻔﻣ
(OFF) ﻝﻳﻐﺷﺗﻟﺍ ﻑﺎﻘﻳﺇ ﺡﺎﺗﻔﻣ
ﻲﺋﺎﺑﺭﻬﻛﻟﺍ ﺫﻔﻧﻣﻟﺍ ﻥﻣ ﺫﺧﺄﻣﻟﺍ ﺱﺑﺎﻗ ﻝﺻﻓﺍ
ﺭﻳﺫﺣﺗ
II ﺔﺋﻓ ﺓﺩﻋ
ﺔﻳﺳﺎﻳﻗ ﺕﺎﻘﺣﻠﻣ
ﻰﻠﻋ ﺔﻋﻭﻣﺟﻣﻟﺍ ﻱﻭﺗﺣﺗ ،(ﺓﺩﺣﺍﻭ ﺓﺩﺣﻭ)ﺔﻳﺳﻳﺋﺭﻟﺍ ﺓﺩﺣﻭﻟﺍ ﻰﻟﺇ ﺔﻓﺎﺿﻹﺎﺑ
.ﻩﺎﻧﺩﺃ ﻝﻭﺩﺟﻟﺍ ﻲﻓ ﺎﻫﺩﺭﺳ ﻡﺗ ﻲﺗﻟﺍ ﺕﺎﻘﺣﻠﻣﻟﺍ
1......................................................... ﺔﻳﻁﺎﻁﻣ ﺓﺩﺎﺳﻭ (1)
1........................................ (ﺓﺩﺭﻭﻭ ﺭﺎﻣﺳﻣﺑ) ﻲﻘﻠﺣ ﺽﺑﻘﻣ (2)
1................................................... ﻲﻁﻳﺭﺷ ﻁﺑﺭ ﺡﺎﺗﻔﻣ (3)
.ﺭﺎﻁﺧﺇ ﻥﻭﺩ ﺔﻳﺳﺎﻳﻘﻟﺍ ﺕﺎﻘﻠﺣﻣﻟﺍ ﺭﻳﻳﻐﺗ ﻥﻛﻣﻳ
ﺕﺎﻘﻳﺑﻁﺗ
.ﺔﻟﻭﻘﺻﻣﻟﺍ ﺔﻳﻧﺩﻌﻣﻟﺍ ﺢﻁﺳﻷﺍ ○
ﺔﻟﺍﺯﺇﻭ ﺃﺩﺻﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﻼﻁﻟﺍ ﻝﺑﻗ ﺔﻳﻧﺩﻌﻣﻟﺍ ﺢﻁﺳﻸﻟ ﺔﻳﺩﻳﻬﻣﺗﻟﺍ ﺓﺭﻔﻧﺻﻟﺍ ○
.ءﻼﻁﻟﺍ ﺓﺩﺎﻋﺇ ﻝﺑﻗ ﻡﻳﺩﻘﻟﺍ ءﻼﻁﻟﺍ
ﻥﻣ ﺏﺷﺧﻟﺍ ﻊﻁﻘﻟ ﺕﺍﺭﻳﺩﻘﺗﻟﺍ ﺢﻳﺣﺻﺗﻭ ﺔﻳﺑﺷﺧﻟﺍ ﻝﺎﻣﻋﻷﺍ ﻝﻘﺻ
○
.ﺕﺎﺑﻳﻛﺭﺗﻟﺍ ﻭﺃ ﺕﻼﺻﻭﻟﺍ
.ءﻼﻁﻟﺍ ءﺩﺑ ﻝﺑﻗ ﺔﻳﺑﺷﺧﻟﺍ ﺢﻁﺳﻸﻟ ﺔﻳﺩﻳﻬﻣﺗﻟﺍ ﺓﺭﻔﻧﺻﻟﺍ ○
ﻝﺎﺛﻣﻟﺍ ﻝﻳﺑﺳ ﻰﻠﻋ ،ﺔﻧﻭﻫﺩﻣﻟﺍ ﺔﻳﻧﺩﻌﻣﻟﺍ ﺢﻁﺳﻷﺍ ﻊﻳﻣﻠﺗ ﻭﺃ ﻝﻘﺻ
○
ﺔﻁﺎﻳﺧﻟﺍ ﺕﺎﻧﻳﻛﺎﻣﻭ ﺕﺎﺟﻼﺛﻟﺍﻭ ﺩﻋﺎﺻﻣﻟﺍﻭ ﺕﺍﺭﺎﻁﻘﻟﺍﻭ ﺕﺍﺭﺎﻳﺳﻠﻟ
.ﻙﻟﺫ ﺭﻳﻏﻭ ﺔﻳﻧﺩﻌﻣﻟﺍ ﺔﻳﺑﺭﻬﻛﻟﺍ ﺓﺯﻬﺟﻷﺍﻭ ﺕﻻﺎﺳﻐﻟﺍﻭ
.ﻙﻟﺫ ﺭﻳﻏﻭ ،ﻲﺑﺷﺧﻟﺍ ﺙﺎﺛﻸﻟ ﺔﻌﻣﻠﻣﻟﺍ ﺢﻁﺳﻷﺍ ﻝﻘﺻ ○
.ﺕﻳﻧﻭﺑﻷﺍ ﺕﺎﺟﺗﻧﻣ ﻭﺃ ﺔﻳﻋﺎﻧﻁﺻﻻﺍ ﻥﺋﺍﺩﻠﻟﺍ ﻊﻳﻣﻠﺗ ○
ﺕﺎﻔﺻﺍﻭﻣﻟﺍ
،ﺕﻟﻭﻓ 220 ،ﺕﻟﻭﻓ 120 ،ﺕﻟﻭﻓ 110)
(ﺕﻟﻭﻓ 240 ،ﺕﻟﻭﻓ 230
ﻲﺑﺭﻬﻛﻟﺍ ﺩﻬﺟﻟﺍ
*(ﻕﻁﺎﻧﻣﻟﺍ ﺏﺳﺣ)
*ﺕﺍﻭ 1250 ﺔﻗﺎﻁﻟﺍ ﻝﺎﺧﺩﺇ
ﺔﻘﻳﻗﺩ/ 3400 - 0 ﻝﻳﻣﺣﺗ ﻪﻋﺭﺳ ﺩﺟﻭﺗ ﻻ
ﺔﻘﻳﻗﺩ/ 3750 ﺔﻧﻧﻘﻣﻟﺍ ﺔﻋﺭﺳﻟﺍ
ﻡﻣ 22 × 180 ﺹﺭﻗ ﻡﺟﺣﻟ ﻲﺟﺭﺎﺧﻟﺍ ﺭﻁﻘﻟﺍ
ﻲﻠﺧﺍﺩﻟﺍ ﺭﻁﻘﻟﺍ ×ﺓﺭﻔﻧﺻﻟﺍ
ﻡﺟﻛ 2.8 ،ﻙﻠﺳﻟﺍ ﻥﻭﺩﺑ) ﻥﺯﻭﻟﺍ
(ﺔﻳﺳﺎﻳﻘﻟﺍ ﺕﺎﻘﺣﻠﻣﻟﺍﻭ
ﺔﺿﺭُﻋﺎﻬﻧﺃ ﺙﻳﺣ ﺞﺗﻧﻣﻟﺍ ﻰﻠﻋ ﺓﺩﻭﺟﻭﻣﻟﺍ ﻡﺳﻻﺍ ﺔﺣﻭﻟ ﺹﺣﻓ ﻥﻣ ﺩﻛﺄﺗ *
.ﻕﻁﺎﻧﻣﻟﺍ ﺏﺳﺣ ﺭﻳﻳﻐﺗﻠﻟ
ﺔﻅﺣﻼﻣ
ﺕﺎﻔﺻﺍﻭﻣﻟﺍ ﺭﻳﻐﺗﺗ ،ﺭﻣﺗﺳﻣﻟﺍ ﺭﻳﻭﻁﺗﻟﺍﻭ ﺙﺣﺑﻠﻟ HiKOKI ﺞﻣﺎﻧﺭﺑﻟ ﺎًﻌﺑﺗ
.ﻕﺑﺳﻣ ﻡﻼﻋﺇ ﻥﻭﺩ ﺎﻧﻫ ﺓﺭﻭﻛﺫﻣﻟﺍ
ﻝﻳﻐﺷﺗﻟﺍﻭ ﺏﻳﻛﺭﺗﻟﺍ
ءﺍﺭﺟﻹﺍﻝﻛﺷﻟﺍﺔﺣﻔﺻ
ﻲﻘﻠﺣ ﺽﺑﻘﻣ ﻁﺑﺭ
110
ﺓﺭﻔﻧﺻ ﺹﺭﻗ ﺏﻳﻛﺭﺗ
210
ﻲﻓﻭﺻ ءﺎﻁﻏ ﺏﻳﻛﺭﺗ
310
ﺔﻋﺭﺳﻟﺍ ﺭﻳﻐﺗﻣ ﻝﻳﻐﺷﺗﻭ ﺡﺎﺗﻔﻣﻟﺍ ﻝﻳﻐﺷﺗ
410
ﺓﺭﻔﻧﺻﻟﺍ ءﺩﺑ
511
ﺔﻳﻧﻭﺑﺭﻛﻟﺍ ﺓﺎﺷﺭﻔﻟﺍ ﻝﺍﺩﺑﺗﺳﺍ
611
ﺕﺎﻘﺣﻠﻣﻟﺍ ﺩﻳﺩﺣﺗ
―12
ﺭﻳﻭﺩﺗ ﻕﻳﺭﻁ ﻥﻋ ﺔﺑﻏﺭﻟﺍ ﺏﺳﺣ ﺓﺭﻳﻐﺗﻣ ﻥﻭﻛﺗ ﻥﺃ ﻥﻛﻣﻳ ﻙﺭﺣﻣﻟﺍ ﺔﻋﺭﺳ
ﺽﻔﺧﻧﺗﻭ ،"6" ﻩﺎﺟﺗﻻﺍ ﻲﻓ ﺹﺭﻘﻟﺍ ﻝﻳﻭﺣﺗ ﻝﻼﺧ ﻥﻣ ﺩﻳﺯﺗ ﺙﻳﺣﺑ ؛ﺹﺭﻘﻟﺍ
."1" ﻩﺎﺟﺗﻻﺍ ﻲﻓ ﻪﻠﻳﻭﺣﺗ ﻕﻳﺭﻁ ﻥﻋ
ﻲﻟﺎﺗﻟﺍ ﻝﻭﺩﺟﻟﺍ .ﻪﺑ ﻡﺎﻳﻘﻟﺍ ﻡﺗﻳ ﻱﺫﻟﺍ ﻝﻣﻌﻠﻟ ﺔﺑﺳﺎﻧﻣﻟﺍ ﻙﺭﺣﻣﻟﺍ ﺔﻋﺭﺳ ﺩﺩﺣ
ﺭﻬﻅﻳﻭ ﺹﺭﻘﻟﺍ ﺱﺎﻳﻘﻣ ﻰﻠﻋ ﺭﺷﺅﻣ ﻝﻛﻟ ﺔﻠﺑﺎﻘﻣﻟﺍ ﻙﺭﺣﻣﻟﺍ ﺕﺎﻋﺭﺳ ﺢﺿﻭﻳ
.ﺎﻬﻟ ﺔﺑﺳﺎﻧﻣﻟﺍ ﻝﻣﻌﻟﺍ ﻉﺍﻭﻧﺃ
ﺹﺭﻘﻟﺍ ﺱﺎﻳﻘﻣ
R.P.M.
(ﺔﻘﻳﻗﺩﻟﺍ ﻲﻓ ﺓﺭﻭﺩ)
ﻝﻣﻌﻟﺍ ﻉﻭﻧ
1600
ﻝﻘﺻﻠﻟ 21100
31700
42300
52900
ﺓﺭﻔﻧﺻﻠﻟ
63400
ﻪﻳﺑﻧﺗ
ﻲﻓ ﺱﺎﻳﻘﻣﻟﺍ ﻰﻠﻋ "1" ﻭﺃ "6" ﻥﻣ ﺭﺛﻛﺃ ﺹﺭﻘﻟﺍ ﺭﻳﻭﺩﺗ ﻥﻛﻣﻳ ﻻ
.ﺎﻬﻧﻣ ٍﻝﻛ ﺕﺎﻫﺎﺟﺗﺍ
0000BookSP18VA.indb70000BookSP18VA.indb7 2018/05/1510:15:422018/05/1510:15:42

8
٢
ﻝﻘﺻﻟﺍ ﺕﺎﻳﻠﻣﻋ ﻭﺃ ﺓﺭﻔﻧﺻﻠﻟ ﺔﻌﺋﺎﺷﻟﺍ ﺔﻣﻼﺳﻟﺍ ﺕﺍﺭﻳﺫﺣﺗ
ﺓءﺍﺭﻘﺑ ﻡﻗ .ﻊﻁﻗ ﻭﺃ ﺫﺣﺷ ﺓﺍﺩﺄﻛ ﻝﻣﻌﺗﻟ ﻩﺫﻫ ﺔﻳﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻩﺫﻫ ﺕﻣﻣُﺻ(ﺃ
ﺕﺎﻔﺻﺍﻭﻣﻟﺍﻭ ،ﺕﺎﺣﻳﺿﻭﺗﻟﺍﻭ ،ﺕﺎﻣﻳﻠﻌﺗﻟﺍﻭ ،ﻥﺎﻣﻷﺍ ﺕﺍﺭﻳﺫﺣﺗ ﻝﻛ
.ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻊﻣ ﺔﻣﺩﻘﻣﻟﺍ
ﺔﻳﺋﺎﺑﺭﻬﻛ ﺔﻣﺩﺻ ﻲﻓ ﻩﺎﻧﺩﺃ ﺓﺩﺭﺳﻣﻟﺍ ﺕﺎﻣﻳﻠﻌﺗﻟﺍ ﻉﺎﺑﺗﺍ ﻲﻓ ﻝﺷﻔﻟﺍ ﺏﺑﺳﺗﻳ ﺩﻗ
.ﺔﺑﺎﺻﺇ ﻭﺃ ،ﻕﻳﺭﺣ ﻭﺃ
ﻭﺃ ،ﻝﻘﺻﻟﺍ ﻝﺛﻣ ﺕﺎﻳﻠﻣﻋ ﻲﻓ ﻩﺫﻫ ﺔﻳﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺍﺩﺧﺗﺳﺎﺑ ﻰﺻﻭﻳ ﻻ(ﺏ
.ﻊﻁﻘﻟﺍ ﻭﺃ ،ﻙﻼﺳﻷﺍ ﻑﻳﻅﻧﺗ
ﻲﻓ ﺎﻬﻟ ﺔﺻﺻﺧﻣﻟﺍ ﺭﻳﻏ ﺕﺎﻳﻠﻣﻌﻟﺍ ﻲﻓ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻡﺍﺩﺧﺗﺳﺍ ﺏﺑﺳﺗﻳ ﺩﻗ
.ﺔﻳﺻﺧﺷﻟﺍ ﺔﺑﺎﺻﻹﺍﻭ ﺭﻁﺎﺧﻣﻟﺍ
ﻝﺑﻗ ﻥﻣ ﺎﻬﺑ ﻰﺻﻭﻣﻟﺍﻭ ﺎًﺻﻳﺻﺧ ﺔﻣﻣﺻﻣﻟﺍ ﺭﻳﻏ ﺕﺎﻘﺣﻠﻣﻟﺍ ﻡﺩﺧﺗﺳﺗ ﻻ(ﺕ
.ﺓﺍﺩﻷﺍ ﻊﻳﻧﺻﺗ ﺔﻬﺟ
ﻥﻣﺿﺗ ﻼﻓ ،ﻙﺑ ﺔﺻﺎﺧﻟﺍ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺄﺑ ﻕﺣﻠﻣﻟﺍ ﻕﺎﻓﺭﺇ ﻥﻛﻣﻳ ﻪﻧﻷﻭ
.ﻥﻣﻵﺍ ﻝﻳﻐﺷﺗﻟﺍ
ﺩﺣﻠﻟ ﻝﻗﻷﺍ ﻰﻠﻋ ﺔﻳﻭﺎﺳﻣ ﻕﺣﻠﻣﻠﻟ ﺔﻧﻧﻘﻣﻟﺍ ﺔﻋﺭﺳﻟﺍ ﻥﻭﻛﺗ ﻥﺃ ﺏﺟﻳ (ﺙ
.ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻰﻠﻋ ﺔﻧﻳﺑﻣﻟﺍ ﺔﻋﺭﺳﻠﻟ ﻰﺻﻗﻷﺍ
ﺔﻧﻧﻘﻣﻟﺍ ﺔﻋﺭﺳﻟﺍ ﻥﻣ ﺭﺑﻛﺃ ﺔﻋﺭﺳﺑ ﻝﻣﻌﺗ ﻲﺗﻟﺍ ﺕﺎﻘﺣﻠﻣﻟﺍ ﻝﻁﻌﺗﺗ ﺩﻗ
.ﺍًﺩﻳﻌﺑ ﻝﺻﻔﻧﺗ ﻭﺃ ﺎﻬﺑ ﺔﺻﺎﺧﻟﺍ
ﺩﻭﺩﺣ ﻲﻓ ﻪﻛﻣﺳﻭ ﻙﺑ ﺹﺎﺧﻟﺍ ﻕﺣﻠﻣﻠﻟ ﻲﺟﺭﺎﺧﻟﺍ ﺩﻌﺑﻟﺍ ﻥﻭﻛﻳ ﻥﺃ ﺏﺟﻳ (ﺝ
.ﻙﺑ ﺔﺻﺎﺧﻟﺍ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﻷ ﺔﻧﻧﻘﻣﻟﺍ ﺔﻌﺳﻟﺍ
ﺎﻬﺑ ﻡﻛﺣﺗﻟﺍ ﻭﺃ ﺔﺣﻳﺣﺻﻟﺍ ﺭﻳﻏ ﻡﺎﺟﺣﻷﺍ ﺕﺍﺫ ﺕﺎﻘﺣﻠﻣﻟﺍ ﺔﻳﺎﻣﺣ ﻥﻛﻣﻳ ﻻ
.ﺏﺳﺎﻧﻣ ﻝﻛﺷﺑ
ﻥﺍﺭﻭﺩ ﺩﻭﻣﻋ ﻥﺳ ﻊﻣ ﺕﺎﻘﺣﻠﻣﻠﻟ ﻁﺑﺍﺭﺗﻣﻟﺍ ﺏﻳﻛﺭﺗﻟﺍ ﻕﺑﺎﻁﺗﻳ ﻥﺃ ﺏﺟﻳ (ﺡ
ﻥﺃ ﺏﺟﻳ ،ﻩﺎﻔﺷﻟﺍ ﺔﻁﺳﺍﻭﺑ ﺎﻬﺑﻳﻛﺭﺗ ﻡﺗﻳ ﻲﺗﻟﺍ ﺕﺎﻘﺣﻠﻣﻠﻟ .ﺔﺧﻼﺟﻟﺍ
.ﻩﺎﻔﺷﻟﺍ ﺩﻳﺩﺣﺗ ﺭﻁﻗ ﻊﻣ ﻕﺣﻠﻣﻟﺍ ﺭﻭﺣﻣ ﺔﺣﺗﻓ ﺏﺳﺎﻧﺗﺗ
ﺎﻬﻧﺯﺍﻭﺗ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﺏﻳﻛﺭﺗ ﺯﺎﻬﺟ ﻊﻣ ﻰﺷﺎﻣﺗﺗ ﻻﻲﺗﻟﺍ ﺕﺎﻘﺣﻠﻣﻟﺍ ﺩﻘﻔﺗ
.ﺓﺭﻁﻳﺳﻟﺍ ﺩﻘﻓ ﻲﻓ ﺏﺑﺳﺗﺗ ﺩﻗﻭ ﺓﺩﺷﺑ ﺯﺗﻬﺗﻭ
ﻲﻓ ﺎﻣﺑ ﻕﺣﻠﻣﻟﺍ ﺹﺣﻔﺑ ﻡﻗ ﻡﺍﺩﺧﺗﺳﺍ ﻝﻛ ﻝﺑﻗ .ﻑﻟﺎﺗ ﻕﺣﻠﻣ ﻡﺩﺧﺗﺳﺗ ﻻ(ﺥ
ﻭﻠﺧﻭ ،ﻕﻭﻘﺷﻟﺍﻭ ﺢﺋﺍﺭﺷﻟﺍ ﻥﻣ ﺔﻁﺷﺎﻛﻟﺍ ﺕﻼﺟﻌﻟﺍ ﻭﻠﺧ ﻥﻣ ﺩﻛﺄﺗﻟﺍ ﻙﻟﺫ
ﺔﺷﺭﻓ ﻭﻠﺧﻭ ،ﻝﻛﺄﺗﻟﺍﻭ ﻕﺯﻣﺗﻟﺍﻭ ﻕﻭﻘﺷﻟﺍ ﻥﻣ ﻲﻔﻠﺧﻟﺍ ﺢﺑﻛﻟﺍ ﺔﺻﻧﻣ
ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﺕﻁﻘﺳ ﺍﺫﺇ .ﺔﻋﺩﺻﺗﻣﻟﺍ ﻭﺃ ﺔﻛﻭﻛﻔﻣﻟﺍ ﻙﻼﺳﻷﺍ ﻥﻣ ﻙﻼﺳﻷﺍ
.ﻑﻟﺎﺗ ﺭﻳﻏ ﻕﺣﻠﻣ ﺏﻳﻛﺭﺗﺑ ﻡﻗ ﻭﺃ ﻑﻠﺗﺗ ﻡﻟ ﺎﻬﻧﺃ ﻥﻣ ﺩﻛﺄﺗ ،ﻕﻠﺣﻣﻟﺍ ﻭﺃ
ﻕﺣﻠﻣﻟﺍ ﻥﻋ ﻙﺑ ﻥﻳﻁﻳﺣﻣﻟﺍﻭ ﺕﻧﺃ ﺩﻌﺗﺑﺍ ،ﻕﺣﻠﻣﻟﺍ ﺏﻳﻛﺭﺗﻭ ﺹﺣﻔﻟﺍ ﺩﻌﺑ
ﻝﻣﺣ ﻥﻭﺩ ﺔﻋﺭﺳﻠﻟ ﻰﺻﻗﻷﺍ ﺩﺣﻟﺍ ﻰﻠﻋ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻝﻳﻌﺷﺗﺑ ﻡﻗﻭ ﺭﺍﻭﺩﻟﺍ
.ﺓﺩﺣﺍﻭ ﺔﻘﻳﻗﺩﻟ
.ﺭﺎﺑﺗﺧﻻﺍ ﺕﻗﻭ ﻲﻓ ًﺓﺩﺎﻋ ﺔﻔﻟﺎﺗﻟﺍ ﺕﺎﻘﺣﻠﻣﻟﺍ ﻙﻛﻔﺗﺗ
ﻭﺃ ﻪﺟﻭﻟﺍ ﻲﻗﺍﻭ ﻡﺩﺧﺗﺳﺍ ،ﻡﺍﺩﺧﺗﺳﻻﺍ ﺏﺳﺣ .ﺔﻳﻗﺍﻭﻟﺍ ﺕﺍﺩﻌﻣﻟﺍ ﺩﺗﺭﺍ (ﺩ
ﻥﻣ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ءﺍﺩﺗﺭﺎﺑ ﻡﻗ ،ءﺎﺿﺗﻗﻻﺍ ﺏﺳﺣ .ﺔﻳﻗﺍﻭﻟﺍ ﺕﺍﺭﺎﻅﻧﻟﺍ
ﻝﻣﻌﻟﺍ ﺔﺷﺭﻭ ءﺎﻗﻭﻭ ،ﺕﺍﺯﺎﻔﻘﻟﺍﻭ ،ﻥﺫﻷﺍ ﺔﻳﺎﻣﺣ ﺕﺍﺩﻌﻣﻭ ،ﺔﺑﺭﺗﻷﺍ
.ﺎﻳﺎﻅﺷﻟﺍ ﻭﺃ ﻁﺷﻛﻠﻟ ﻡﻭﺎﻘﻣﻟﺍ
ﺞﺗﺎﻧﻟﺍ ﺩﻋﺎﺻﺗﻣﻟﺍ ﻡﺎﻁﺣﻟﺍ ﺩﺻ ﻰﻠﻋ ﺓﺭﺩﺎﻗ ﻥﻳﻧﻳﻌﻟﺍ ﺔﻳﺎﻣﺣ ﻥﻭﻛﺗ ﻥﺃ ﺏﺟﻳ
ﺍًﺭﺩﺎﻗ ﺔﺑﺭﺗﻷﺍ ﻥﻣ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ﻥﻭﻛﻳ ﻥﺃ ﺏﺟﻳ .ﺔﻔﻠﺗﺧﻣﻟﺍ ﺕﺎﻳﻠﻣﻌﻟﺍ ﻥﻋ
.ﺎﻬﺑ ﻡﻭﻘﺗ ﻲﺗﻟﺍ ﺕﺎﻳﻠﻣﻌﻟﺍ ﻥﻋ ﺔﺟﺗﺎﻧﻟﺍ ﺕﺎﺋﻳﺯﺟﻟﺍ ﺢﻳﺷﺭﺗ ﻰﻠﻋ
ﺓﺭﺩﻘﻟﺍ ﻥﺍﺩﻘﻓ ﻲﻓ ﺔﻳﻟﺎﻌﻟﺍ ءﺎﺿﻭﺿﻠﻟ ﺔﻠﻳﻭﻁ ﺕﺍﺭﺗﻔﻟ ﺽﺭﻌﺗﻟﺍ ﺏﺑﺳﺗﻳ ﺩﻗ
.ﻊﻣﺳﻟﺍ ﻰﻠﻋ
ﺔﻘﻁﻧﻣ ﻝﺧﺩﻳ ﻥﻣ ﻝﻛ ﻰﻠﻋ ﺏﺟﻳ .ﻝﻣﻌﻟﺍ ﺔﻘﻁﻧﻣ ﻥﻋ ﺍًﺩﻳﻌﺑ ﺓﺭﺎﻣﻟﺍ ﻕﺑﺍ (ﺫ
.ﺔﻳﺻﺧﺷﻟﺍ ﺔﻳﺎﻗﻭﻟﺍ ﺕﺍﺩﻌﻣ ءﺍﺩﺗﺭﺍ ﻝﻣﻌﻟﺍ
ﺕﺎﻘﺣﻠﻣﻟﺍ ﻭﺃ ﺔﻔﻠﺗﺧﻣﻟﺍ ﺕﺎﻳﻠﻣﻌﻟﺍ ﻥﻋ ﺔﺟﺗﺎﻧﻟﺍ ﺎﻳﺎﻅﺷﻟﺍ ﺭﻳﺎﻁﺗﺗ ﺩﻗ
.ﻝﻣﻌﻟﺍ ﺔﻘﻁﻧﻣ ﺝﺭﺎﺧ ﺔﺑﺎﺻﺇ ﻲﻓ ﺏﺑﺳﺗﺗﻭ ﺓﺭﻭﺳﻛﻣﻟﺍ
ءﺍﺩﺃ ﺩﻧﻋ ﻁﻘﻓ ﺔﻟﻭﺯﻌﻣﻟﺍ ﺽﺑﻘﻣﻟﺍ ﺢﻁﺳﺄﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻙﺳﻣﺍ (ﺭ
ﻙﻠﺳﻟﺎﺑ ﻭﺃ ﺔﻳﻔﺧﻣ ﻙﻼﺳﺄﺑ ﻊﻳﻁﻘﺗﻟﺍ ﺕﺎﻘﺣﻠﻣ ﺎﻬﻳﻓ ﻝﺻﺗ ﺩﻗ ﺔﻳﻠﻣﻋ
.ﺎﻬﺑ ﺹﺎﺧﻟﺍ
ءﺍﺯﺟﻸﻟ ﺽﺭﻌﺗﺗ ﺩﻗ "ﺭﺷﺎﺑﻣ" ﻙﻠﺳﺑ ﺔﻠﺻﺗﻣﻟﺍ ﻊﻳﻁﻘﺗﻟﺍ ﺕﺎﻘﺣﻠﻣ
ﺔﻣﺩﺻﺑ ﺔﻳﻠﻣﻌﻟﺍ ﺏﻳﺻﺗ ﺩﻗﻭ "ﺓﺭﺷﺎﺑﻣﻟﺍ" ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﺔﻳﻧﺩﻌﻣﻟﺍ
.ﺔﻳﺋﺎﺑﺭﻬﻛ
.ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣ ﻥﻋ ﺍًﺩﻳﻌﺑ ﻙﻠﺳﻟﺍ ﻊﺿ (ﺯ
ﻙﻋﺍﺭﺫﻭ ﻙﺩﻳ ﺏﺣﺳ ﻡﺗﻳﻭ ﻕﺯﻣﺗﻳ ﻭﺃ ﻙﻠﺳﻟﺍ ﻊﻁﻘﻧﻳ ﺩﻘﻓ ،ﻡﻛﺣﺗﻟﺍ ﺕﺩﻘﻓ ﺍﺫﺇ
.ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣ ﻰﻟﺇ
.ﺎًﻣﺎﻣﺗ ﻕﺣﻠﻣﻟﺍ ﻑﻗﻭﺗﻳ ﻰﺗﺣ ﻝﻔﺳﻷ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﺍًﺩﺑﺃ ﻊﺿﺗ ﻻ(ﺱ
.ﻡﻛﺣﺗﻟﺍ ﻥﻋ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﺝﺭﺧﻳﻭ ﺢﻛﺳﻟﺎﺑ ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣ ﻙﺳﻣﻳ ﺩﻗ
.ﻙﺑﻧﺎﺟ ﻰﻠﻋ ﺎﻬﻠﻣﺣ ءﺎﻧﺛﺃ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻝﻳﻐﺷﺗ ﻰﻠﻋ ﻝﻣﻌﺗ ﻻ(ﺵ
ﺎﻣﻣ ،ﻙﺳﺑﻼﻣ ﻊﻁﻗ ﻲﻓ ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣﻟ ﺊﺟﺎﻔﻣﻟﺍ ﺱﻣﻠﻟﺍ ﺏﺑﺳﺗﻳ ﺩﻘﻓ
.ﻙﻣﺳﺟ ﻩﺎﺟﺗﺍ ﻲﻓ ﻕﺣﻠﻣﻟﺍ ﺏﺣﺳﻳ
.ﺭﺍﺭﻣﺗﺳﺎﺑ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺄﺑ ﺔﻳﻭﻬﺗﻟﺍ ءﺯﺟ ﻑﻳﻅﻧﺗﺑ ﻡﻗ(ﺹ
ﺔﺑﺭﺗﻷﺍ ﻡﻛﺍﺭﺗ ﺓﺩﺎﻳﺯ ﺏﺑﺳﺗﺗ ﺩﻗﻭ ﻪﻠﺧﺍﺩ ﺔﺑﺭﺗﻷﺍ ﻙﺭﺣﻣﻟﺍ ﺔﺣﻭﺭﻣ ﺏﺣﺳﺗ
.ﺔﻳﺋﺎﺑﺭﻬﻛ ﺭﻁﺎﺧﻣ ﻲﻓ
.ﻝﺎﻌﺗﺷﻼﻟ ﺔﻠﺑﺎﻗ ﺩﺍﻭﻣ ﻥﻣ ﺏﺭﻘﻟﺎﺑ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻝﻳﻐﺷﺗ ﻰﻠﻋ ﻝﻣﻌﺗ ﻻ(ﺽ
.ﺩﺍﻭﻣﻟﺍ ﻩﺫﻫ ﻝﺎﻌﺗﺷﺇ ﻰﻟﺇ ﺭﺭﺷﻟﺍ ﻱﺩﺅﻳ ﺩﻗ
.ﺔﻠﺋﺎﺳ ﺕﺍﺩﺭﺑﻣ ﺏﻠﻁﺗﺗ ﻲﺗﻟﺍ ﺕﺎﻘﻠﺣﻣﻟﺍ ﻡﺩﺧﺗﺳﺗ ﻻ(ﻁ
ﺭﺎﻳﺗﻟﺎﺑ ﻕﻌﺻ ﻲﻓ ﺔﻠﺋﺎﺳﻟﺍ ﺕﺍﺩﺭﺑﻣﻟﺍ ﻭﺃ ءﺎﻣﻟﺍ ﻡﺍﺩﺧﺗﺳﺍ ﺏﺑﺳﺗﻳ ﺩﻗ
.ﺔﻳﺋﺎﺑﺭﻬﻛ ﺔﻣﺩﺻ ﻭﺃ ﻲﺋﺎﺑﺭﻬﻛﻟﺍ
ﺔﻠﺻﻟﺍ ﺕﺍﺫ ﺕﺍﺭﻳﺫﺣﺗﻟﺍﻭ ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ
ﺢﺑﻛﻟﺍ ﺔﺻﻧﻣﻭ ،ﻥﺍﺭﻭﺩﻟﺍ ﺔﻠﺟﻌﻟ ﺊﺟﺎﻔﻣ ﻝﻌﻓ ﺩﺭ ﻭﻫ ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ
ﺏﻘﺛﻟﺍ ﺏﺑﺳﺗﻳ ﺩﻗ .ﺔﻗﺯﻣﻣﻟﺍ ﻭﺃ ﺔﺑﻭﻘﺛﻣﻟﺍ ﻯﺭﺧﻷﺍ ﺕﺎﻘﺣﻠﻣﻟﺍ ﻥﻣ ﻱﺃﻭ ،ﻲﻔﻠﺧﻟﺍ
ﻊﻓﺩ ﻲﻓ ﺏﺑﺳﺗﻳ ﺎﻣﻣ ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣﻟ ﺊﺟﺎﻔﻣﻟﺍ ﻑﻗﻭﺗﻟﺍ ﺔﻋﺭﺳ ﻲﻓ ﻕﺯﻣﺗﻟﺍ ﻭﺃ
ﺔﻁﻘﻧ ﻲﻓ ﻕﺣﻠﻣﻟﺍ ﻥﺍﺭﻭﺩﻟ ﺱﻛﺎﻌﻣﻟﺍ ﻩﺎﺟﺗﻻﺍ ﻲﻓ ﻡﻛﺣﺗﻟﺍ ﺓﺩﻗﺎﻓ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ
.ﻁﺑﺭﻟﺍ
ﺩﻗ ،ﻝﻣﻌﻟﺍ ﺔﺟﻳﺗﻧ ﺕﺑﻘُﺛﻭﺃ ﺔﻁﺷﺎﻛ ﺔﻠﺟﻋ ﺕﻗﺯﻣﺗ ﺍﺫﺇ ،ﻝﺎﺛﻣﻟﺍ ﻝﻳﺑﺳ ﻰﻠﻋ
ﻲﻓ ﺏﺑﺳﺗﻣ ﺓﺩﺎﻣﻟﺍ ﺢﻁﺳ ﻝﺧﺍﺩ ﺏﻘﺛﻟﺍ ﺔﻁﻘﻧﺑ ﺔﻠﺧﺍﺩﻟﺍ ﺔﻠﺟﻌﻟﺍ ﺔﻓﺎﺣ ﺱﺭﻐﺗ
ﺎًﻘﻓﻭ ﻙﻟﺫﻭ ﻪﻧﻋ ﺍًﺩﻳﻌﺑ ﻭﺃ ﻝﻣﺎﻌﻟﺍ ﻩﺎﺟﺗﺎﺑ ﺔﻠﺟﻌﻟﺍ ﺕﻠﻔﻧﺗ ﺩﻗ .ﺔﻠﺟﻌﻟﺍ ﺕﻼﻔﻧﺇ
.ﺏﻘﺛﻟﺍ ﺔﻅﺣﻟ ﻲﻓ ﺔﻠﺟﻌﻟﺍ ﺔﻛﺭﺣ ﻩﺎﺟﺗﻻ
.ﻑﻭﺭﻅﻟﺍ ﻩﺫﻫ ﻲﻓ ﻁﺷﻛﻟﺍ ﺕﻼﺟﻋ ﻙﻟﺫﻛ ﻑﻠﺗﺗ ﺩﻗ
ﻝﻳﻐﺷﺗ ﺕﺍءﺍﺭﺟﺇ ﻭﺃ/ﻭﺔﻓﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻡﺍﺩﺧﺗﺳﺍ ءﻭﺳ ﺔﺟﻳﺗﻧ ﻭﻫ ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ
ﺎﻣﻛ ﺔﺑﺳﺎﻧﻣﻟﺍ ﺕﺎﻁﺎﻳﺗﺣﻻﺍ ﺫﺎﺧﺗﺎﺑ ﻪﺑﻧﺟﺗ ﻥﻛﻣﻳﻭ ،ﺔﺣﻳﺣﺻ ﺭﻳﻏ ﺕﻻﺎﺣ ﻭﺃ
.ﻲﻠﻳ
ﻡﻭﺎﻘﻣ ﻩﺎﺟﺗﺍ ﻲﻓ ﻙﻋﺍﺭﺫﻭ ﻙﻣﺳﺟ ﻥﻭﻛﻳ ﺙﻳﺣﺑ ﺍًﺩﻳﺟ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻙﺳﻣﺍ (ﺃ
،ﺭﻓﻭﺗ ﻰﺗﻣ ،ﻲﻓﺎﺿﻹﺍ ﺽﺑﻘﻣﻟﺍ ﺎًﻣﺋﺍﺩ ﻡﺩﺧﺗﺳﺍ .ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ ﺓﻭﻘﻟ
ﻝﺎﻌﻓﺃ ﺩﻭﺩﺭﻭ ﺱﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ ﻲﻓ ﻡﻛﺣﺗﻠﻟ ﻰﺻﻗﻷﺍ ﺩﺣﻟﺍ ﻰﻠﻋ ﻝﻭﺻﺣﻠﻟ
.ﻝﻳﻐﺷﺗﻟﺍ ءﺩﺑ ءﺎﻧﺛﺃ ﻥﺍﺭﻭﺩﻟﺍ ﻡﺯﻋ
ﺩﺍﺩﺗﺭﻻﺍ ﺓﻭﻗ ﻭﺃ ﻝﻳﻐﺷﺗﻟﺍ ﻡﺯﻋ ﻝﺎﻌﻓﺃ ﺩﻭﺩﺭ ﻲﻓ ﻡﻛﺣﺗﻟﺍ ﻝﻣﺎﻌﻠﻟ ﻥﻛﻣﻳ
.ﺔﺑﺳﺎﻧﻣﻟﺍ ﺕﺎﻁﺎﻳﺗﺣﻻﺍ ﺫﺎﺧﺗﺍ ﺩﻧﻋ ﻲﺳﻛﻌﻟﺍ
.ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣ ﻥﻣ ﺏﺭﻘﻟﺎﺑ ﺍًﺩﺑﺃ ﻙﺩﻳ ﻊﺿﺗ ﻻ(ﺏ
.ﻙﻳﺩﻳ ﻰﻠﻋ ﺎًﻳﺳﻛﻋ ﻕﺣﻠﻣﻟﺍ ﺩﺗﺭﻳ ﺩﻗ
ﺙﺩﺣ ﺍﺫﺇ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﺎﻬﻳﻓ ﻙﺭﺣﺗﺗ ﻲﺗﻟﺍ ﺔﻘﻁﻧﻣﻟﺍ ﻲﻓ ﻙﻣﺳﺟ ﻊﺿﺗ ﻻ(ﺕ
.ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ
ﺩﻧﻋ ﺔﻠﺟﻌﻟﺍ ﺔﻛﺭﺣﻟ ﺱﻛﺎﻌﻣ ﻩﺎﺟﺗﺍ ﻲﻓ ﺓﺍﺩﻷﺍ ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ ﻊﻓﺩﻳ
.ﻕﺯﻣﺗﻟﺍ
ﻑﺍﻭﺣﻟﺍﻭ ،ﻥﺎﻛﺭﻷﺍ ﻲﻓ ﻝﻣﻌﻟﺍ ﺩﻧﻋ ﺔﺻﺎﺧ ﺔﻳﺎﻣﺣ ﺕﺍﺩﻌﻣ ﻡﺩﺧﺗﺳﺍ (ﺙ
.ﻕﺣﻠﻣﻟﺍ ﻕﻳﺯﻣﺗﻭ ﺩﺍﺩﺗﺭﺍ ﺏﻧﺟﺗ .ﺎﻬﻠﺛﺎﻣﻳ ﺎﻣﻭ ،ﺓﺩﺎﺣﻟﺍ
ﻥﺍﺭﻭﺩﻟﺍ ﻕﺣﻠﻣ ﻊﻁﻗ ﻲﻓ ﺩﺍﺩﺗﺭﻻﺍﻭ ﺓﺩﺎﺣﻟﺍ ﻑﺍﻭﺣﻟﺍﻭ ﻥﺎﻛﺭﻷﺍ ﺏﺑﺳﺗﺗ ﺩﻗ
.ﻲﺳﻛﻌﻟﺍ ﺩﺍﺩﺗﺭﻻﺍ ﻭﺃ ﻡﻛﺣﺗﻟﺍ ﻥﺍﺩﻘﻓ ﻲﻓ ﺏﺑﺳﺗﻳ ﺎﻣﻣ
.ﺔﻧﻧﺳﻣ ﺭﺷﻧ ﺓﺭﻔﺷ ﻭﺃ ﺭﺷﻧﻟﺍ ﺔﻠﺳﻠﺳﻟ ﺏﺷﺧ ﺭﻔﺣ ﺓﺭﻔﺷ ﻕﺎﻓﺭﺈﺑ ﻡﻘﺗ ﻻ(ﺝ
.ﻡﻛﺣﺗﻟﺍ ﻥﺍﺩﻘﻓﻭ ﻲﺳﻛﻋ ﺩﺍﺩﺗﺭﺍ ﻰﻟﺇ ﺕﺍﺭﻔﺷﻟﺍ ﻩﺫﻫ ﻱﺩﺅﺗ
ﺓﺭﻔﻧﺻﻟﺍ ﺕﺎﻳﻠﻣﻌﻟ ﺓﺩﺩﺣﻣﻟﺍ ﺔﻣﻼﺳﻟﺍ ﺕﺍﺭﻳﺫﺣﺗ
ﺕﺎﻬﺟ ﺕﺎﻳﺻﻭﺗ ﻊﺑﺗﺍ .ﺩﺋﺍﺯ ﻡﺟﺣ ﺕﺍﺫ ﺓﺭﻔﻧﺻ ﺹﺍﺭﻗﺃ ﻕﺭﻭ ﻡﺩﺧﺗﺳﺗ ﻻ(ﺃ
.ﺓﺭﻔﻧﺻﻟﺍ ﻕﺭﻭ ﺩﻳﺩﺣﺗ ﺩﻧﻋ ﻊﻳﻧﺻﺗﻟﺍ
ﺽﺭﻌﺗﻳ ﺓﺭﻔﻧﺻﻟﺍ ﺓﺩﺎﺳﻭ ءﺍﺭﻭ ﺩﺗﻣﻳ ﻱﺫﻟﺍ ﺭﺑﻛﻷﺍ ﺓﺭﻔﻧﺻﻟﺍ ﻕﺭﻭ
.ﺩﺍﺩﺗﺭﻻﺍ ﻭﺃ ﺹﺭﻘﻟﺍ ﻙﻟﺎﻬﺗﻭ ﻕﺯﻣﺗﻟﺍ ﻲﻓ ﺏﺑﺳﺗﻳ ﺩﻗﻭ ﻕﻳﺯﻣﺗﻟﺍ ﺭﻁﺎﺧﻣﻟ
ﻝﻘﺻﻟﺍ ﺕﺎﻳﻠﻣﻌﻟ ﺓﺩﺩﺣﻣﻟﺍ ﺔﻣﻼﺳﻟﺍ ﺕﺍﺭﻳﺫﺣﺗ
ﺎﻬﺗﺎﻘﺣﻠﻣ ﺕﺎﻘﻠﺣ ﻭﺃ ﻝﻘﺻﻟﺍ ءﺎﻁﻏ ﻥﻣ ﺔﻳﺧﺗﺭﻣ ﺔﺑﺳﻧﺑ ﺢﻣﺳﺗ ﻻ(ﺃ
.ﺎﻬﺻﻗ ﻭﺃ ﺔﻳﺧﺗﺭﻣ ﻁﺑﺭﻟﺍ ﺕﺎﻘﻠﺣ ﻱﺃ ﻲﻁﺑ ﻡﻗ .ﺔﻳﺭﺣﺑ ﻥﺍﺭﻭﺩﻠﻟ
ﻊﻁﻗ ﻭﺃ ﻙﻌﺑﺎﺻﺃ ﻕﻠﻌﺗ ﻥﺃ ﻥﻛﻣﻳ ﺓﺭﺍﻭﺩﻟﺍ ﻭﺃ ﺔﻳﺧﺗﺭﻣﻟﺍ ﻁﺑﺭﻟﺍ ﺕﺎﻘﻠﺣ
.ﻝﻣﻌﻟﺍ ﺔﻌﻁﻗ
ﺓﺭﻔﻧﺻﻟﺍ ﻝﻘﺻ ﺓﺍﺩﺃ ﻡﺍﺩﺧﺗﺳﺍ ﺩﻧﻋ ﺔﻣﺯﻼﻟﺍ ﺕﺎﻁﺎﻳﺗﺣﻻﺍ
ﺔﻳﻧﻭﺭﺗﻛﻟﻹﺍ
.ﺔﻧﻭﺣﺎﻁﻛ ﺓﺍﺩﻷﺍ ﻩﺫﻫ ﻡﺍﺩﺧﺗﺳﺍ ﻝﻭﺎﺣﻭ ﺦﻳﻠﺟﺗﻟﺍ ﺔﻠﺟﻋ ﺏﻳﻛﺭﺗﺑ ﻡﻘﺗ ﻻ
1
ﺓﺩﻌﻠﻟ ﻲﺑﻧﺎﺟﻟﺍ ﺽﺑﻘﻣﻟﺍﻭ ﻝﻛﻳﻬﻟﺍ ﺽﺑﻘﻣ ﻙﺳﻣ ﻰﻠﻋ ﺎًﻣﻭﺩ ﺹﺭﺣﺍ
2
.ﻡﺎﻛﺣﺈﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
.ﺓﺭﻁﺧﻭ ﻝﺑ ﺔﻘﻳﻗﺩ ﺭﻳﻏ ﺕﺎﻳﻠﻣﻋ ﻲﻓ ﺔﻳﺳﻛﻌﻟﺍ ﺓﻭﻘﻟﺍ ﺏﺑﺳﺗﺗﺳ ﻻﺇﻭ
0000BookSP18VA.indb80000BookSP18VA.indb8 2018/05/1510:15:422018/05/1510:15:42

9١
ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﺔﻣﻼﺳﺑ ﺔﺻﺎﺧﻟﺍ ﺔﻣﺎﻌﻟﺍ ﺕﺍﺭﻳﺫﺣﺗﻟﺍ
ﺭﻳﺫﺣﺗ
.ﺕﺎﻣﻳﻠﻌﺗﻟﺍ ﺔﻓﺎﻛﻭ ﺔﻣﻼﺳﻟﺍ ﺕﺍﺭﻳﺫﺣﺗ ﺔﻓﺎﻛ ﺓءﺍﺭﻘﺑ ﻡﻗ
ﺔﻣﺩﺻ ﻲﻓ ﻩﺎﻧﺩﺃ ﺓﺩﺭﺳﻣﻟﺍ ﺕﺎﻣﻳﻠﻌﺗﻟﺍﻭ ﺕﺍﺭﻳﺫﺣﺗﻟﺍ ﻉﺎﺑﺗﺍ ﻲﻓ ﻝﺷﻔﻟﺍ ﺏﺑﺳﺗﻳ ﺩﻗ
.ﺔﺑﺎﺻﺇ ﻭﺃ/ﻭ،ﻕﻳﺭﺣ ﻭﺃ ﺔﻳﺋﺎﺑﺭﻬﻛ
.ًﻼﺑﻘﺗﺳﻣ ﺎﻬﻳﻟﺇ ﻉﻭﺟﺭﻠﻟ ﺕﺎﻣﻳﻠﻌﺗﻟﺍﻭ ﺕﺍﺭﻳﺫﺣﺗﻟﺍ ﺔﻓﺎﻛ ﻅﻔﺣﺍ
ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻰﻟﺇ ﺕﺍﺭﻳﺫﺣﺗﻟﺍ ﻲﻓ "ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ" ﺢﻠﻁﺻﻣ ﺭﻳﺷﻳ
ﺓﺩﻌﻟﺍ ﻭﺃ ﻙﺑ ﺔﺻﺎﺧﻟﺍ ﺔﻳﺳﻳﺋﺭﻟﺍ ﻝﻳﻐﺷﺗﻟﺍ ﺕﻼﺻﻭﻣ ﻝﻣﻌﺗ ﻲﺗﻟﺍ (ﺔﻳﻛﻠﺳﻟﺍ)
.ﺔﻳﺭﺎﻁﺑﻟﺎﺑ ﻝﻣﻌﺗ ﻲﺗﻟﺍ (ﺔﻳﻛﻠﺳﻼﻟﺍ) ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﻝﻣﻌﻟﺍ ﺔﻘﻁﻧﻣ ﺔﻣﻼﺳ (1
.ﻙﻠﻐﺷ ﻥﺎﻛﻣ ﺓءﺎﺿﺇ ﻥﺳﺣﻭ ﺔﻓﺎﻅﻧ ﻰﻠﻋ ﻅﻓﺎﺣ (ﺃ
ﺏﺑﺳﺗﺗ ﺓءﺎﺿﻣ ﺭﻳﻐﻟﺍ ﻝﻣﻌﻟﺍ ﺕﻻﺎﺟﻣﻭ ﻝﻣﻌﻟﺍ ﻥﺎﻛﻣ ﻲﻓ ﻰﺿﻭﻔﻟﺎﻓ
.ﺙﺩﺍﻭﺣ ﻉﻭﻗﻭ ﻲﻓ
ﻲﻓ ﻱﺃ ﺔﻳﺭﺎﺟﻔﻧﺍ ءﺍﻭﺟﺃ ﻲﻓ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻝﻳﻐﺷﺗﺑ ﻡﻘﺗ ﻻ(ﺏ
.ﺭﺎﺑﻏ ﻭﺃ ﻝﺎﻌﺗﺷﻼﻟ ﺔﻠﺑﺎﻗ ﺕﺍﺯﺎﻏ ﻭﺃ ﻝﺋﺍﻭﺳ ﺩﻭﺟﻭ
.ﺔﻧﺧﺩﻷﺍ ﺭﺎﺑﻏ ﻝﺎﻌﺷﺇ ﻰﻠﻋ ﻝﻣﻌﺗ ﺓﺭﺍﺭﺷ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﺙﺩﺣﺗ
ﻝﺎﻔﻁﻷﺍ ﻝﻭﺎﻧﺗﻣ ﻥﻋ ﺓﺩﻳﻌﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻥﻭﻛﺗ ﻥﺃ ﻰﻠﻋ ﻅﻓﺎﺣ (ﺕ
.ﻙﺑ ﻥﻳﻁﻳﺣﻣﻟﺍ ﻭﺃ
ﻙﺩﻘﻓ ﻰﻟﺇ ﻱﺩﺅﺗ ﻥﺃ ﻥﻛﻣﻣﻟﺍ ﻥﻣ ﺕﻳﺗﺷﺗﻟﺍ ﻝﺎﻛﺷﺃ ﻥﻣ ﻝﻛﺷ ﻱﺃ
.ﺓﺭﻁﻳﺳﻟﺍ
ﺔﻳﺑﺭﻬﻛﻟﺍ ﺕﺎﻣﺩﺻﻟﺍ ﻥﻣ ﺔﻳﺎﻗﻭﻟﺍ (2
ﻱﺄﺑ ﺱﺑﺎﻘﻟﺍ ﻝﻳﺩﻌﺗ ﺭﻅﺣﻳ ،ءﺎﺑﺭﻬﻛﻟﺍ ﺫﻔﻧﻣﺑ ﺱﺑﺎﻘﻟﺍ ﻝﻳﺻﻭﺗ ﺏﺟﻳ (ﺃ
.ﺔﻘﻳﺭﻁ
.ﺔﻳﺿﺭﻷﺍ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻊﻣ ﺊﻳﺎﻬﻣ ﺱﺑﺎﻗ ﻱﺃ ﻡﺩﺧﺗﺳﺗ ﻻ
ﺭﻁﺧ ﻥﻣ ﺔﻣﺋﻼﻣﻟﺍ ﺱﺑﺎﻘﻣﻟﺍﻭ ﺎﻫﺭﻳﻳﻐﺗ ﻡﺗﻳ ﻡﻟ ﻲﺗﻟﺍ ﺱﺑﺍﻭﻘﻟﺍ ﺽﻔﺧﺗ
. ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺕﺎﻣﺩﺻﻟﺍ ﺙﻭﺩﺣ
ﺏﻳﺑﺎﻧﻷﺍ ﻝﺛﻣ ﺔﻳﺿﺭﻷﺍ ﺢﻁﺳﻷﺍ ﻊﻣ ﻱﺩﺳﺟﻟﺍ ﺱﻣﻼﺗﻟﺍ ﺏﻧﺟﺗ (ﺏ
.ﺩﻗﺍﻭﻣﻟﺍﻭ ﺕﺎﺟﻼﺛﻟﺍﻭ ﺔﻳﺭﺍﺭﺣﻟﺍ ﺕﻻﺩﺎﺑﻣﻟﺍﻭ
ﻙﺎﻧﻫ ﺔﻳﺿﺭﻷﺍ ﺢﻁﺳﻷﺍ ﻙﻠﺗ ﻥﻣ ﻱﻷ ﻙﻣﺳﺟ ﺔﺳﻣﻼﻣ ﺔﻟﺎﺣ ﻲﻓ
.ﺔﻳﺑﺭﻬﻛ ﺔﻣﺩﺻﻟ ﻙﺿﺭﻌﺗﻟ ﺓﺭﻭﻁﺧ
.ﺔﺑﻭﻁﺭﻟﺍ ﻭﺃ ﺭﻁﻣﻠﻟ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﺽﺭﻌﺗ ﻻ(ﺕ
ﺓﺩﻌﻟﺍ ﻝﺧﺍﺩ ﻰﻟﺇ ءﺎﻣﻟﺍ ﺏﺭﺳﺗ ﻥﺇ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺕﺎﻣﺩﺻﻟﺍ ﺭﻁﺧ ﺩﺍﺩﺯﻳ
.ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﻭﺃ ﻝﻣﺣﻟ ًﺎﻘﻠﻁﻣ ﻪﻠﻣﻌﺗﺳﺗ ﻻ،(ﻙﻠﺳﻟﺍ) ﻝﺑﺎﻛﻟﺍ ﻝﺎﻣﻌﺗﺳﺍ ءﻲﺳﺗ ﻻ(ﺙ
.ﺱﺑﻘﻣﻟﺍ ﻥﻣ ﺱﺑﺎﻘﻟﺍ ﺏﺣﺳﻟ ﻭﺃ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻊﻓﺩ ﻭﺃ ﺩﺷ
ﻑﺍﻭﺣﻟﺍ ﻭﺃ ﺕﻳﺯﻟﺍ ﻭﺃ ﺓﺭﺍﺭﺣﻟﺍ ﺭﺩﺎﺻﻣ ﻥﻋ ًﺍﺩﻳﻌﺑ ﻪﻳﻠﻋ ﻅﻓﺎﺣﻭ
.ﺔﻛﺭﺣﺗﻣﻟﺍ ﺯﺎﻬﺟﻟﺍ ءﺍﺯﺟﺃ ﻭﺃ ﺓﺩﺎﺣﻟﺍ
ﺕﺎﻣﺩﺻﻟﺍ ﺭﻁﺧ ﻥﻣ ﺔﻛﺑﺎﺷﺗﻣﻟﺍ ﻭﺃ ﺔﻔﻟﺎﺗﻟﺍ (ﻙﻼﺳﻷﺍ) ﺕﻼﺑﺎﻛﻟﺍ ﺩﻳﺯﺗ
.ﺔﻳﺑﺭﻬﻛﻟﺍ
ﻡﺍﺩﺧﺗﺳﺎﺑ ﺢﺻﻧﻳ ،ﺝﺭﺎﺧﻟﺎﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ ﺔﻟﺎﺣ ﻲﻓ (ﺝ
.ﻲﺟﺭﺎﺧﻟﺍ ﻝﺎﻣﻌﺗﺳﻻﺍ ﻊﻣ ﺏﺳﺎﻧﺗﻳ (ﻝﺑﺎﻛ) ﻙﻠﺳ
ﻥﻣ ﻝﻳﻠﻘﺗﻠﻟ ﻲﺟﺭﺎﺧﻟﺍ ﻝﺎﻣﻌﺗﺳﻻﺍ ﻊﻣ ﺏﺳﺎﻧﻣ ﻙﻠﺳ ﻡﺍﺩﺧﺗﺳﺎﺑ ﻡﻗ
.ﺔﻳﺑﺭﻬﻛ ﺔﻣﺩﺻﻟ ﺽﺭﻌﺗﻟﺍ ﺓﺭﻭﻁﺧ
ﺭﻔﻣ ﻻﺭﻣﺃ ﺏﻁﺭ ﻥﺎﻛﻣ ﻲﻓ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ ﻥﻭﻛﻳ ﺎﻣﺩﻧﻋ (ﺡ
.(RCD) ﻲﻘﺑﺗﻣﻟﺍ ﻲﺑﺭﻬﻛﻟﺍ ﺭﺎﻳﺗﻠﻟ ﻲﻣﺣﻣﻟﺍ ﺩﻭﺯﻣﻟﺍ ﻡﺩﺧﺗﺳﺎﻓ ،ﻪﻧﻣ
ﺕﺎﻣﺩﺻﺑ ﺔﺑﺎﺻﻹﺍ ﺭﻁﺎﺧﻣ ﻝﻳﻠﻘﺗ ﻰﻠﻋ
RCD
ﻡﺍﺩﺧﺗﺳﺍ ﻝﻣﻌﻳ
.ﺔﻳﺑﺭﻬﻛ
ﺔﻳﺻﺧﺷﻟﺍ ﺔﻣﻼﺳﻟﺍ (3
ﺓﺩﻌﻟﺍ ﺔﻁﺳﺍﻭﺑ ﻝﻣﻌﻟﺎﺑ ﻡﻗﻭ ﻪﻠﻌﻔﺗ ﺎﻣ ﻰﻟﺇ ﻪﺑﺗﻧﺃﻭ ﺎًﻅﻘﻳ ﻥﻛ (ﺃ
ﻙﺭﻭﻌﺷ ﺔﻟﺎﺣ ﻲﻓ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺩﺧﺗﺳﺗ ﻻ.ﻝﻘﻌﺗﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﺩﺍﻭﻣ ﻭﺃ ﺔﻳﻭﺩﺃ ﻭﺃ ﺓﺭﺩﺧﻣ ﺩﺍﻭﻣ ﺭﻳﺛﺄﺗ ﺕﺣﺗ ﺕﻧﻛ ﺍﺫﺇ ﻭﺃ ﺏﻌﺗﻟﺎﺑ
.ﺔﻳﻟﻭﺣﻛ
ﻱﺩﺅﻳ ﺩﻗ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺍﺩﺧﺗﺳﺇ ﺩﻧﻋ ﺓﺩﺣﺍﻭ ﺔﻅﺣﻠﻟ ﻩﺎﺑﺗﻧﻹﺍ ﻡﺩﻋ
.ﺓﺭﻳﻁﺧ ﺔﺑﺎﺻﺇ ﻰﻟﺇ
.ﻥﻳﻌﻠﻟ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ءﺍﺩﺗﺭﺎﺑ ﺎًﻣﺋﺍﺩ ﻡﻗ .ﻥﺎﻣﻷﺍ ﺕﺍﻭﺩﺃ ﻡﺩﺧﺗﺳﺍ (ﺏ
ﺔﻳﺫﺣﺃ ﻭﺃ ﺭﺎﺑﻐﻟﺍ ﻥﻣ ﻲﻗﺍﻭﻟﺍ ﻉﺎﻧﻘﻟﺍ ﻝﺛﻣ ﺔﻳﺎﻣﺣﻟﺍ ﺕﺍﻭﺩﺃ ﻝﻣﻌﺗﺳ
ﻊﻣﺳﻟﺍ ﺔﻳﺎﻣﺣ ﺓﺯﻬﺟﺃ ﻭﺃ ﺔﺑﻠﺻ ﺔﻌﺑﻗ ﻭﺃ ﻕﻻﺯﻧﻼﻟ ﺓﺩﺎﺿﻣﻟﺍ ﻥﺎﻣﻷﺍ
ﺕﻻﺎﻣﺗﺣﺍ ﻝﻳﻠﻘﺗ ﻰﻠﻋ ﺔﻧﻳﻌﻣ ﻑﻭﺭﻅ ﻲﻓ ﺎﻬﻣﺍﺩﺧﺗﺳﺍ ﻡﺗﻳ ﻲﺗﻟﺍﻭ
.ﺔﻳﺻﺧﺷ ﺕﺎﺑﺎﺻﻹ ﺽﺭﻌﺗﻟﺍ
ﻊﺿﻭﻟﺍ ﻲﻓ ﺡﺎﺗﻔﻣﻟﺍ ﻥﺃ ﻥﻣ ﺩﻛﺄﺗ .ﺩﻭﺻﻘﻣﻟﺍ ﺭﻳﻏ ﻝﻳﻐﺷﺗﻟﺍ ﻊﻧﻣ (ﺕ
ﺔﻣﺯﺣ ﻭﺃ/ﻭﺔﻗﺎﻁﻟﺍ ﺭﺩﺻﻣﺑ ﻝﻳﺻﻭﺗﻟﺍ ﻝﺑﻗ ﻝﻳﻐﺷﺗﻟﺍ ﻑﺎﻘﻳﺇ
.ﺓﺍﺩﻷﺍ ﻝﻣﺣ ﻭﺃ ﻁﺎﻘﺗﻟﻻﺍﻭ ،ﺔﻳﺭﺎﻁﺑﻟﺍ
ﻭﺃ ﺡﺎﺗﻔﻣﻟﺍ ﻲﻓ ﻙﻌﺑﺻﺇ ﺩﻭﺟﻭ ﻊﻣ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻝﻣﺣ ﻱﺩﺅﻳ
ﻝﻳﻐﺷﺗﻟﺍ ﻊﺿﻭ ﻲﻓ ﺡﺎﺗﻔﻣﻟﺍ ﺎﻬﻳﻓ ﻥﻭﻛﻳ ﻲﺗﻟﺍ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ
.ﺙﺩﺍﻭﺣ ﻉﻭﻗﻭ ﻝﺎﻣﺗﺣﺍ ﻰﻟﺇ
.ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ ﻝﺑﻗ ﻁﺑﺭﻟﺍ ﺡﺎﺗﻔﻣ ﻭﺃ ﻁﺑﺿﻟﺍ ﺩﺩﻋ ﻉﺯﻧﺍ (ﺙ
ﻥﻣ ﻙﺭﺣﺗﻣﻟﺍ ءﺯﺟﻟﺍ ﺭﺎﺳﻳ ﻰﻠﻋ ﻁﺑﺿ ﺡﺎﺗﻔﻣ ﻭﺃ ﻁﺑﺭ ﺡﺎﺗﻔﻣ ﺩﻭﺟﻭ
.ﺔﻳﺻﺧﺷ ﺔﺑﺎﺻﺇ ﺙﻭﺩﺣ ﻰﻟﺇ ﻱﺩﺅﻳ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ
ﻥﻳﺑﻭ ﻙﻧﻳﺑ ﺔﺑﺳﺎﻧﻣ ﺔﻓﺎﺳﻣ ﻙﺭﺗﺍ ،ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻥﻣ ﺏﺭﺗﻘﺗ ﻻ(ﺝ
.ﺕﺎﻗﻭﻷﺍ ﻊﻳﻣﺟ ﻲﻓ ﻙﻧﺯﺍﻭﺗ ﻰﻠﻋ ﻅﻓﺎﺣﻭ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ
ﻲﻓ ﻝﺿﻓﺃ ﻝﻛﺷﺑ ﺯﺎﻬﺟﻟﺍ ﻰﻠﻋ ﺓﺭﻁﻳﺳﻟﺍ ﻥﻣ ﻙﻟﺫ ﻙﻟ ﺢﻣﺳﻳﺳ
.ﺔﻌﻗﻭﺗﻣﻟﺍ ﺭﻳﻏ ﻑﻗﺍﻭﻣﻟﺍ
ﺎﻬﺑ ﻭﺃ ﺔﺿﺎﻔﺿﻓ ﺱﺑﻼﻣ ﻱﺩﺗﺭﺗ ﻻ،ﺔﺑﺳﺎﻧﻣ ﺱﺑﻼﻣ ءﺍﺩﺗﺭﺎﺑ ﻡﻗ (ﺡ
ﺱﺑﻼﻣﻟﺍﻭ ﻙﺭﻌﺷ ﺩﺎﻌﺑﺇ ﻰﻠﻋ ًﺎﻣﺋﺍﺩ ﻅﻓﺎﺣﻭ ،ﻲﻠﺣ ﻭﺃ ﺔﺑﺋﺎﺳ ﻑﺍﺭﻁﺃ
ﺓﺩﻌﻟﺍ ﻥﻣ ﺔﻛﺭﺣﺗﻣﻟﺍ ءﺍﺯﺟﻷﺍ ﻥﻋ ًﺍﺩﻳﻌﺑ ﺯﺎﻔﻘﻟﺍﻭ ﺎﻬﻳﺩﺗﺭﺗ ﻲﺗﻟﺍ
.ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﻲﻠﺣﻟﺍ ﻭﺃ ﻑﺍﺭﻁﺃ ﺎﻬﺑ ﻲﺗﻟﺍ ﻭﺃ ﺔﺿﺎﻔﺿﻔﻟﺍ ﺱﺑﻼﻣﻟﺍ ﻙﺑﺷﺎﺗﺗ ﺩﻗ
.ﺏﺎﻘﺛﻣﻠﻟ ﺔﻛﺭﺣﺗﻣﻟﺍ ءﺍﺯﺟﻷﺎﺑ ﻝﻳﻭﻁﻟﺍ ﺭﻌﺷﻟﺍﻭﺃ
ﺔﻠﺻﺗﻣ ﻥﻣ ﺩﻛﺄﺗﻓ .ﺭﺎﺑﻐﻟﺍ ﻊﻳﻣﺟﺗﻭ ﻁﻔﺷ ﺯﺎﻬﺟ ﺏﻳﻛﺭﺗ ﺯﺎﺟ ﻥﺇ (ﺥ
.ﻡﻳﻠﺳ ﻝﻛﺷﺑ ﺎﻬﻣﺍﺩﺧﺗﺳﺍ ﻡﺗﻳﻭ
ﻥﻋ ﺔﻣﺟﺎﻧﻟﺍ ﺭﻁﺎﺧﻣﻟﺍ ﻝﻳﻠﻘﺗ ﻰﻟﺇ ﺭﺎﺑﻐﻟﺍ ﻊﻳﻣﺟﺗ ﻡﺍﺩﺧﺗﺳﺍ ﻱﺩﺅﻳ ﺩﻗ
.ﺭﺎﺑﻐﻟﺍ
:ﺎﻬﺑ ﺔﻳﺎﻧﻌﻟﺍﻭ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺍﺩﺧﺗﺳﺍ ﺔﻘﻳﺭﻁ (4
ﺓﺩﻌﻟﺍ ﻡﺩﺧﺗﺳﺍﻭ ،ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺍﺩﺧﺗﺳﺍ ﻲﻓ ﻁﺭﻔﺗ ﻻ(ﺃ
.ﻪﺑ ﻡﻭﻘﺗ ﻱﺫﻟﺍ ﻝﻣﻌﻠﻟ ﺔﺑﺳﺎﻧﻣﻟﺍ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﺍﺫﻫ ﻥﺈﻓ ﻙﻟﺫﻟ ﺔﺻﺻﺧﻣﻟﺍ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻙﻣﺍﺩﺧﺗﺳﺍ ﺩﻧﻋ
ﺔﻣﻬﻣﻠﻟ ًﺎﻌﺑﺗ ًﺎﻧﻣﺃ ﺭﺛﻛﺃﻭ ﻝﺿﻓﺃ ﺔﺟﻳﺗﻧ ﻰﻠﻋ ﻝﻭﺻﺣﻟﺍ ﻰﻠﻋ ﻙﺩﻋﺎﺳﻳ
.ﺎﻬﻟ ﺏﺎﻘﺛﻣﻟﺍ ﻡﻳﻣﺻﺗ ﻡﺗ ﻲﺗﻟﺍ
ﺓﺩﻌﻟﺍ ﻡﺩﺧﺗﺳﺗ ﻻﻝﻣﻌﻟﺍ ﻥﻋ ﻝﻳﻐﺷﺗﻟﺍ ﺡﺎﺗﻔﻣ ﻝﻁﻌﺗ ﺔﻟﺎﺣ ﻲﻓ (ﺏ
.ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ
ﺎﻬﺑ ﺹﺎﺧﻟﺍ ﻝﻳﻐﺷﺗﻟﺍ ﺡﺎﺗﻔﻣ ﻲﻓ ﻡﻛﺣﺗﻟﺍ ﻥﻛﻣﻳ ﻻﺔﻳﺋﺎﺑﺭﻬﻛ ﺓﺩﻋ ﻱﺃ
.ﺡﺎﺗﻔﻣﻟﺍ ﺍﺫﻫ ﺡﻼﺻﺇ ﺏﺟﻳﻭ ﺎﻬﻣﺍﺩﺧﺗﺳﺍ ﺩﻧﻋ ًﺍﺭﻁﺧ ﻝﻛﺷﺗ ﺎﻬﻧﺈﻓ
ﻥﻣ ﺔﻳﺭﺎﻁﺑﻟﺍ ﺔﻣﺯﺣ ﻭﺃ/ﻭﺔﻗﺎﻁﻟﺍ ﺭﺩﺻﻣ ﻥﻣ ﺱﺑﺎﻘﻟﺍ ﻝﺻﻔﺑ ﻡﻗ (ﺕ
ﻭﺃ ﺕﺎﻘﺣﻠﻣﻟﺍ ﺭﻳﻳﻐﺗ ﻭﺃ ﺕﻼﻳﺩﻌﺗ ﻱﺃ ﻝﻣﻋ ﻝﺑﻗ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ
.ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻥﻳﺯﺧﺗ
ﺭﻳﻏ ﻝﻛﺷﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻝﻳﻐﺷﺗ ﻩﺫﻫ ﻁﺎﻳﺗﺣﻻﺍ ﺕﺍءﺍﺭﺟﺇ ﻊﻧﻣﺗ
.ﺩﻭﺻﻘﻣ
ﻝﻭﺎﻧﺗﻣ ﻥﻋ ًﺃﺩﻳﻌﺑ ﺔﻣﺩﺧﺗﺳﻣ ﺭﻳﻐﻟﺍ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﻥﻳﺯﺧﺗﺑ ﻡﻗ (ﺙ
ﻝﻳﻐﺷﺗ ﻥﻋ ﺓﺭﻛﻓ ﻪﻳﺩﻟ ﺱﻳﻟ ﺹﺧﺷ ﻱﻷ ﺢﻣﺳﺗ ﻻﻭ ﻝﺎﻔﻁﻷﺍ
.ﺎﻬﻠﻳﻐﺷﺗ ﻭﺃ ﺕﺍﻭﺩﻷﺍ ﻩﺫﻫ ﻥﻣ ﺏﺍﺭﺗﻗﻻﺎﺑ ﺏﺎﻘﺛﻣﻟﺍ
ﻥﻳﺑﺭﺩﻣ ﺭﻳﻐﻟﺍ ﺹﺎﺧﺷﻷﺍ ﻱﺩﻳﺃ ﻲﻓ ﺓﺭﻭﻁﺧ ﻝﺛﻣﺗ ﻝﻳﻐﺷﺗﻟﺍ ﺕﺍﻭﺩﺃ
.ﺎﻬﻳﻠﻋ
ﺔﻳﺣﺎﻧ ﻥﻣ ًﺍﺩﻳﺟ ﺎﻬﺻﺣﻔﺑ ﻡﻗ ،ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺩﺩﻌﻟﺍ ﺔﻣﻼﺳ ﻥﻣ ﺩﻛﺄﺗ (ﺝ
ءﺯﺟ ﻱﺃ ﻲﻓ ﺭﺳﻛ ﻱﺃ ﺩﻭﺟﻭ ﻭﺃ ﺔﻛﺭﺣﺗﻣﻟﺍ ءﺍﺯﺟﻷﺍ ﻁﺑﺍﺭﺗ ﻯﺩﻣ
.ﺎﻬﻠﻳﻐﺷﺗ ﻰﻠﻋ ﺭﺛﺅﻳ ﺎﻣﺑ ﺎﻬﺋﺍﺯﺟﺃ ﻥﻣ
ﻝﺑﻗ ﺎﻬﺣﻼﺻﺇ ﺏﺟﻳ ﻝﻳﻐﺷﺗﻟﺍ ﺕﺍﻭﺩﺄﺑ ﻑﻠﺗ ﺙﻭﺩﺣ ﺔﻟﺎﺣ ﻲﻓ
.ﻡﺍﺩﺧﺗﺳﻻﺍ
ﺭﻳﻏ ﻝﻛﺷﺑ ﺔﻧﺎﻳﺻﻟﺍ ﺔﻳﻠﻣﻌﺑ ﻡﺎﻳﻘﻟﺍ ﻭﺃ ﻝﻳﻐﺷﺗﻟﺍ ﺕﺍﻭﺩﺃ ﺔﻧﺎﻳﺻ ﻡﺩﻋ
.ﺙﺩﺍﻭﺣﻟﺍ ﻥﻣ ﺭﻳﺛﻛﻟﺍ ﺙﻭﺩﺣ ﻰﻟﺇ ﻱﺩﺅﻳ ﺢﻳﺣﺻ
ﺔﻔﻳﻅﻧﻭ ﺓﺩﺎﺣ ﻊﻳﻁﻘﺗﻟﺍ ﺕﺍﻭﺩﺃ ﻰﻠﻋ ﻅﺎﻔﺣﻟﺍ ﻰﺟﺭﻳ (ﺡ
ﻝﻬﺳﻳ ﺙﻳﺣﺑ ﻑﺍﻭﺣﻟﺍ ﺓﺩﺎﺣ ﻊﻳﻁﻘﺗﻟﺍ ﺕﺍﻭﺩﺃ ﻰﻠﻋ ﻅﺎﻔﺣﻟﺍ ﻰﺟﺭﻳ
.ﺎﻬﻳﻓ ﻡﻛﺣﺗﻟﺍ
ﻙﻟﺫ ﺭﻳﻏﻭ ﺓﺩﻌﻟﺍ ءﺍﺯﺟﺃﻭ ،ﺕﺎﻘﺣﻠﻣﻟﺍﻭ ،ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻡﺩﺧﺗﺳﺍ (ﺥ
ﻑﻭﺭﻅ ﺭﺎﺑﺗﻋﻻﺍ ﻲﻓ ﻊﺿﻭﻟﺍ ﻊﻣ ،ﺕﺎﻣﻳﻠﻌﺗﻟﺍ ﻩﺫﻫ ﻊﻣ ﻕﻓﺍﻭﺗﻳ ﺎﻣﻳﻓ
.ﺎﻬﻘﻳﻘﺣﺗ ﺏﻭﻠﻁﻣﻟﺍ ﻝﺎﻣﻋﻷﺍﻭ ﻝﻣﻌﻟﺍ
ﻰﻟﺇ ﺎﻬﻟ ﺔﺻﺻﺧﻣﻟﺍ ﺭﻳﻏ ﺽﺍﺭﻏﻸﻟ ﺔﻗﺎﻁﻟﺍ ﺓﺍﺩﺃ ﻡﺩﺧﺗﺳﺍ ﻱﺩﺅﻳ ﺩﻗ
.ﺭﻳﻁﺧ ﻑﻗﻭﻣ ﺩﻭﺟﻭ
ﺔﻣﺩﺧﻟﺍ (5
ﻁﻘﻓﻭ ﻥﻳﺻﺻﺧﺗﻣﻟﺍ ﻝﺑﻗ ﻥﻣ ﻁﻘﻓ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﻙﺗﺩﻋ ﺢﻳﻠﺻﺗﺑ ﺢﻣﺳﺍ (ﺃ
. ﻁﻘﻓ ﺔﻳﻠﺻﻷﺍ ﺭﺎﻳﻐﻟﺍ ﻊﻁﻗ ﻝﺎﻣﻌﺗﺳﺈﺑ
.ﺯﺎﻬﺟﻟﺍ ﻥﺎﻣﺃ ﻰﻠﻋ ﺔﻅﻓﺎﺣﻣﻟﺍ ﻙﻟﺫ ﻥﻣﺅﻳ
ﺕﺎﻁﺎﻳﺗﺣﻻﺍ
.ﻥﺳﻟﺍ ﺭﺎﺑﻛﻭ ﻝﺎﻔﻁﻷﺍ ﻝﻭﺎﻧﺗﻣ ﻥﻋ ًﺍﺩﻳﻌﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻊﺿﻭ ﻰﺟﺭﻳ
ﻥﻋ ﺓﺩﻳﻌﺑ ﺔﻳﺋﺎﺑﺭﻬﻛﻟﺍ ﺓﺩﻌﻟﺍ ﻰﻠﻋ ﻅﺎﻔﺣﻟﺍ ﺏﺟﻳ ﻡﺍﺩﺧﺗﺳﻻﺍ ﻡﺩﻋ ﺔﻟﺎﺣ ﻲﻓ
.ﻥﺳﻟﺍ ﺭﺎﺑﻛﻭ ﻝﺎﻔﻁﻷﺍ ﻝﻭﺎﻧﺗﻣ
0000BookSP18VA.indb90000BookSP18VA.indb9 2018/05/1510:15:422018/05/1510:15:42

10
12
3
4
Lock
Ϩ
123456
1+ 2= 1+ 2=
2
211
3400/min
()
600/min
()
n0
n0
0
1
2
3
4
5
1
2
5
4
3
0000BookSP18VA.indb100000BookSP18VA.indb10 2018/05/1510:15:422018/05/1510:15:42

11
5
6
6 mm
17 mm
43
ⓐⓑ
( )
( )
15° –25°
0000BookSP18VA.indb110000BookSP18VA.indb11 2018/05/1510:15:422018/05/1510:15:42

12
320949
953246Z
953247Z
949434 949844
325941
955857
314090
949103 994322 999043
0000BookSP18VA.indb120000BookSP18VA.indb12 2018/05/1510:15:432018/05/1510:15:43

13
0000BookSP18VA.indb130000BookSP18VA.indb13 2018/05/1510:15:432018/05/1510:15:43

14
0000BookSP18VA.indb140000BookSP18VA.indb14 2018/05/1510:15:432018/05/1510:15:43

15
0000BookSP18VA.indb150000BookSP18VA.indb15 2018/05/1510:15:432018/05/1510:15:43

806
Code No. C99110313 M
Printed in Malaysia
0000BookSP18VA.indb160000BookSP18VA.indb16 2018/05/1510:15:432018/05/1510:15:43