Hillstone SG-6000-E6360 Operating and maintenance manual

Hillstone StoneOS User Manual
Hillstone Hardware Reference Guide
www.hillstonenet.com

2
Name and Concentration of Toxic or Hazardous Substances and Elements in Products | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Name and Concentration of Toxic or Hazardous
Substances and Elements in Products
Component Toxic or hazardous substances and elements
Lead Mercury Cadmium Cr6+ PBB PDBE
Metal parts
(including fasteners) ΧO O OOO
Printed circuit board
assemblies and
components ΧO O OOO
Cables and cable
assemblies ΧO O OOO
Plastics and Polymers ΧO O OΧΧ
Electric components
other than circuit
boards ΧO O OOO
O: Indicates that this toxic or hazardous substance in the material is below the limit
requirement defined in Requirements for Concentration Limits for Certain Hazardous
Substances in Electronic Information Products (SJ/T11363-2006) issued by Ministry
of Information Industry of PRC.
Χ:Indicates that this toxic or hazardous substance in the material exceeds the limit
requirement specified in Requirements for Concentration Limits for Certain Hazardous
Substances in Electronic Information Products (SJ/T11363-2006) issued by Ministry
of Information Industry of PRC.
Note: Not all components in the table are included in one product.
This symbol indicates the environment friendly use period of all products
and components. The period applies only to the normal operation conditions
specified in this guide.

3
Preface | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Preface
About This Guide
Thanks for choosing the network security products from Hillstone Networks, Inc.
This document is an installation guide for Hillstone devices to help you install the
Hillstone device properly.
This guide includes the following chapters:
♦Chapter 1. Introduction
♦Chapter 2. Installation Preparations
♦Chapter 3. Installation
♦Chapter 4. Boot and Configuration
♦Chapter 5. Hardware Maintenance and Replacement
♦Chapter 6. Troubleshooting
♦Addendum FCC Statement
Document Conventions
This guide uses the following conventions for your convenience to read and
understand:
♦Warning: Indicates improper operation that may cause serious damage to
equipment or injury to operators. Thus, operators must strictly follow the
operation rules.
♦Caution: Indicates incorrect operation that may affect the normal use of the
equipment. Operators should be careful.
♦Note: Indicates information that may help readers understand the content.

4
Table of Contents | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table of Contents
CHAPTER 1 INTRODUCTION ........................................................................................................................................ 1
OVERVIEW ......................................................................................................................................................................... 1
HARDWARE OVERVIEW......................................................................................................................................................... 1
Front Panel.................................................................................................................................................................. 1
Back Panel................................................................................................................................................................... 8
LED Indicators ........................................................................................................................................................... 11
System Parameters ................................................................................................................................................... 13
Ports.......................................................................................................................................................................... 17
CLR Button ................................................................................................................................................................ 23
Expansion Slot........................................................................................................................................................... 23
Power Supply ............................................................................................................................................................ 24
Expansion Modules ................................................................................................................................................... 26
CHAPTER 2 INSTALLATION PREPARATIONS................................................................................................................27
INTRODUCTION ................................................................................................................................................................. 27
CLEANNESS REQUIREMENTS................................................................................................................................................. 27
ESD PREVENTION .............................................................................................................................................................. 27
EMI PREVENTION.............................................................................................................................................................. 27
GROUNDING REQUIREMENTS............................................................................................................................................... 28
WORKBENCH REQUIREMENTS .............................................................................................................................................. 28
OTHER SAFETY RECOMMENDATIONS ..................................................................................................................................... 28
UNPACKING...................................................................................................................................................................... 28
INSTALLATION DEVICES/TOOLS/CABLES ................................................................................................................................. 28
CHAPTER 3 INSTALLATION .........................................................................................................................................30
BEFORE INSTALLATION ........................................................................................................................................................ 30
INSTALLING THE DEVICE ON A WORKBENCH ............................................................................................................................ 30
INSTALLING THE DEVICE ON A RACK ....................................................................................................................................... 31
CONNECTING CABLES ......................................................................................................................................................... 32
Connecting the Ground Wire .................................................................................................................................... 33
Connecting the Console Cable................................................................................................................................... 33
Connecting the Ethernet Cable ................................................................................................................................. 33
Connecting an AC Power Cable................................................................................................................................. 35
Connecting a DC Power Cable................................................................................................................................... 36
Connecting a Power Adapter .................................................................................................................................... 37
INSTALLING AN ANTENNA .................................................................................................................................................... 37
INSTALLING THE SIM CARD.................................................................................................................................................. 38
VERIFYING INSTALLATION .................................................................................................................................................... 38
CHAPTER 4 BOOT AND CONFIGURATION ...................................................................................................................40
INTRODUCTION ................................................................................................................................................................. 40
ESTABLISHING A CONFIGURATION ENVIRONMENT .................................................................................................................... 40
Console (CON) Connection ........................................................................................................................................ 40
WebUI ....................................................................................................................................................................... 41

5
Table of Contents | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Tenet and SSH ........................................................................................................................................................... 42
BASIC CONFIGURATION....................................................................................................................................................... 42
CHAPTER 5 HARDWARE MAINTENANCE AND REPLACEMENT ....................................................................................43
INTRODUCTION ................................................................................................................................................................. 43
INSTALLING AND REMOVING THE POWER SUPPLY MODULE........................................................................................................ 43
INSTALLING AND REMOVING THE EXPANSION MODULE ............................................................................................................. 44
Installing and Removing the Fan Tray ...................................................................................................................... 44
Installing and Removing the Anti-dust Mesh............................................................................................................ 45
CHAPTER 6 TROUBLESHOOTING ................................................................................................................................46
INTRODUCTION ................................................................................................................................................................. 46
LOSING THE ADMINISTRATOR PASSWORD ............................................................................................................................... 46
TROUBLESHOOTING POWER SYSTEM ..................................................................................................................................... 46
TROUBLESHOOTING THE CONFIGURATION SYSTEM ................................................................................................................... 46
ADDENDUM FCC STATEMENT ....................................................................................................................................47
COPYRIGHT INFORMATION........................................................................................................................50

6
List of Figures | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
List of Figures
Figure 1-1：SG-6000-E6360 Front Panel..................................................................... 1
Figure 1-2: SG-6000-E6160 Front Panel ..................................................................... 2
Figure 1-3：SG-6000-E5960/E5760/E5660 Front Panel................................................. 3
Figure 1-4: SG-6000-E5560/E5260/E3965 Front Panel ................................................. 3
Figure 1-5: Front Panel of SG-6000-E3960.................................................................. 4
Figure 1-6: Front Panel of SG-6000-E3662/E3660/E2860 ............................................. 5
Figure 1-7: Front Panel of SG-6000-E2800 and SG-6000-E2300.................................... 6
Figure 1-8: SG-6000-E1700/E1606 Front Panel ........................................................... 6
Figure 1-9: SG-6000-E1600 Front Panel ..................................................................... 7
Figure 1-10: Front Panel of SG-6000-E1100 (WLAN version)......................................... 7
Figure 1-11: Front Panel of SG-6000-E1100 (WLAN+3G version)................................... 8
Figure 1-12: SG-6000-E6360/E6160 Back Panel .......................................................... 8
Figure 1-13: SG-6000-E5960/E5760/E5660 Back Panel................................................ 9
Figure 1-14: SG-6000-E5560/E5260/E3965 Back Panel................................................ 9
Figure 1-15: Back Panel of SG-6000-
E3960/E3662/E3660/E2860/E2800/E2300/E1700/E1606 ........................................ 9
Figure 1-16: SG-6000-E1600 Back Panel .................................................................... 9
Figure 1-17: SG-6000-E1100 (WLAN version) Back Panel ........................................... 10
Figure 1-18: SG-6000-E1100 (WALN+3G version) Back Panel ..................................... 11
Figure 1-19: AC Power Module................................................................................. 25
Figure 1-20: DC Power Module ................................................................................ 25
Figure 3-1: Installing the Rubber Pads...................................................................... 30
Figure 3-2: Installing the Floating Nuts..................................................................... 31
Figure 3-3: Installing the Rack-mounting Ears (1U Chassis as example) ....................... 32
Figure 3-4: Installing the Device in a Rack (1U Chassis as example) ............................ 32
Figure 3-5: Connecting the Ground Wire (1U Chassis as example) ............................... 33
Figure 3-6: Connecting the Ethernet Copper Cable..................................................... 34
Figure 3-7: Connecting the Ethernet Fiber Cable........................................................ 35
Figure 3-8: Connecting an AC Power Cable................................................................ 36
Figure 3-9: Connecting a DC Power Cable................................................................. 37
Figure 3-10: 3G Antenna and WLAN Antenna ............................................................ 37
Figure 3-11: Antenna Installation Illustration ............................................................ 38
Figure 4-1: Console Port Configuration ..................................................................... 40
Figure 4-2: Setting Parameters for the Terminal Session ............................................ 41
Figure 5-1: Installing Power Supply Module............................................................... 43
Figure 5-2: Pulling Anti-dust Mesh Out ..................................................................... 45

7
List of Tables | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
List of Tables
Table 1-1: SG-6000-E6360 Front Panel Description .................................................................................................... 2
Table 1-2: SG-6000-E6160 Front Panel Description .................................................................................................... 2
Table 1-3: SG-6000-E5960/E5760/E5660 Front Panel Description ............................................................................. 3
Table 1-4: SG-6000-E5560/E5260/E3965 Front Panel Description ............................................................................. 4
Table 1-5: SG-6000-E3960 Front Panel Description .................................................................................................... 5
Table 1-6: SG-6000-E3662/E3660/E2860 Front Panel Description ............................................................................. 5
Table 1-7: Front Panel Description of SG-6000-E2800 and SG-6000-E2300 ............................................................... 6
Table 1-8: SG-6000-E1700/E1606 Front Panel Description......................................................................................... 6
Table 1-9: SG-6000-E1600 Front Panel Description .................................................................................................... 7
Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version) .................................................................... 7
Table 1-11: Front Panel Description of SG-6000-E1100 (WLAN+3G version).............................................................. 8
Table 1-12: Back Panel Description of SG-6000-E1600............................................................................................. 10
Table 1-13: Back Panel Description of SG-6000-E1100 (WLAN version) ................................................................... 10
Table 1-14: Back Panel Description of SG-6000-E1100 (WLAN+3G version)............................................................. 11
Table 1-15: Front Panel LED Descriptions ................................................................................................................. 11
Table 1-16: System Parameters ................................................................................................................................ 13
Table 1-17: Console Port Attributes .......................................................................................................................... 17
Table 1-18: Auxiliary Port Attributes......................................................................................................................... 18
Table 1-19: USB Port Attributes ................................................................................................................................ 18
Table 1-20: Gigabit Copper Port Attributes .............................................................................................................. 18
Table 1-21: SFP Port Attributes................................................................................................................................. 19
Table 1-22: SFP Optical Module Attributes............................................................................................................... 19
Table 1-23: SFP Copper Module Attributes ............................................................................................................... 20
Table 1-24: SFP+ Port Attributes............................................................................................................................... 20
Table 1-25: SFP+ Optical Module Attributes............................................................................................................. 21
Table 1-26: QSFP+ Port Attributes ............................................................................................................................ 21
Table 1-27: QSFP+ Optical Module Attributes .......................................................................................................... 22
Table 1-28: XFP Port Attributes................................................................................................................................. 22
Table 1-29: XFP Optical Module Attributes............................................................................................................... 22
Table 1-30: Power Supplies of All Product Models.................................................................................................... 24
Table 1-31: Power Supply Module LED Descriptions................................................................................................. 26
Table 2-1: Dust Concentration Requirements in the Equipment Room .................................................................... 27

1
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Chapter 1 Introduction
Overview
Hillstone SG-6000 series product models include SG-6000-E6360, SG-6000-E6160,
SG-6000-E5960, SG-6000-E5760, SG-6000-E5660, SG-6000-E5560, SG-6000-
E5260, SG-6000-E3965, SG-6000-E3960, SG-6000-E3662, SG-6000-E3660, SG-
6000-E2860, SG-6000-E2800, SG-6000-E2300, SG-6000-E1700, SG-6000-E1606,
SG-6000-E1600, SG-6000-E1100 (WLAN version), and SG-6000-E1100 (WLAN+3G
version).
SG-6000-E6360, SG-6000-E6160, SG-6000-E5960, SG-6000-E5760, SG-6000-
E5660, SG-6000-E5560, SG-6000-E5260, SG-6000-E3965, SG-6000-E3960, SG-
6000-E3662, SG-6000-E3660 and SG-6000-E2860 adopt modular design of hot-
swappable circuit boards. For more information about extensible modules, please
see Hillstone SG-6000 M_G_E Series Expansion Modules Reference Guide.
Hardware Overview
Hillstone devices are designed to fit in standard 19-inch cabinets/racks. A device
can be installed in a cabinet/rack or placed on a workbench.
Front Panel
The front panel of SG-6000-E6360 consists of 2 Gigabit Ethernet ports, 8 SFP+
ports, 2 QSFP+ports, 1 USB port, 1 HA port, 1 Management port, 1 Console port, 1
Auxiliary port, 1 CLR button, 1 Bypass expansion slot and several LED indicators.
Figure 1-1
：
SG-6000-E6360 Front Panel

2
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-1: SG-6000-E6360 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power LED 7 FAN: Fan LED 13 HA: HA port
2 STA: Status LED 8 CLR: CLR button 14 e0/0 - e0/1: Gigabit
Ethernet ports
3 ALM: Alarm LED 9 CON: Console port 15 XLe0/2-XLe0/3: QSFP+
ports
4 HA: HA status
LED 10 AUX: Auxiliary
port 16 Bypass expansion slot
5 PS0: Power
supply PS0 LED 11 USB: USB port 17 Xe0/4-Xe0/11: SFP+
ports
6 PS1: Power
supply PS1 LED 12 MGT:
Management port 18 Fan tray
The front panel of SG-6000-E6160 consists of 2 Gigabit Ethernet ports, 8 SFP+
ports, 1 USB port, 1 HA port, 1 Management port, 1 Console port, 1 Auxiliary port,
1 CLR button, 1 Bypass expansion slot and several LED indicators.
Figure 1-2: SG-6000-E6160 Front Panel
Table 1-2: SG-6000-E6160 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power LED 7 FAN: Fan LED 13 HA: HA port
2 STA: Status LED 8 CLR: CLR button 14 e0/0 - e0/1: Gigabit
Ethernet ports
3 ALM: Alarm LED 9 CON: Console port 15 Bypass expansion slot
4 HA: HA status
LED 10 AUX: Auxiliary
port 16 Xe0/2-Xe0/9: SFP+
ports
5 PS0: Power
supply PS0 LED 11 USB: USB port 17 Fan tray
6 PS1: Power
supply PS1 LED 12 MGT:
Management port 18
SG-6000-E5960, SG-6000-E5760, and SG-600-E5660 have the same front panel.
The front panel consist of 4 Gigabit Ethernet ports, 4 SFP ports, 1 USB port, 1 HA
port, 1 Management port, 1 Console port, 1 Auxiliary port, 1 CLR button, 4 general

3
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
expansion slots and several LED indicators. The standard power supply for SG-
6000-E5960/E5760 is dual power supplies, and the product with single power
supply is also available.
Figure 1-3
：
SG-6000-E5960/E5760/E5660 Front Panel
Table 1-3: SG-6000-E5960/E5760/E5660 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power
LED 8 CLR: CLR button 15 e0/2 - e0/5: Gigabit
Ethernet ports
2 STA: Status
LED 9 CON: Console port 16 e0/6 - e0/9: SFP ports
3 ALM: Alarm
LED 10 AUX: Auxiliary
port 17 Slot 1: General expansion
slot
4 HA: HA
status LED 11 Fan tray 18 Slot 2: General expansion
slot (not for storage
expansion module)
5 PS0: Power
supply PS0
LED 12 USB: USB port 19 Slot 3: General expansion
slot (not for storage
expansion module)
6 PS1: Power supply PS1
LED 13 MGT (e0/0):
Management port 20 Slot 4: General expansion
slot (not for storage
expansion module)
7 FAN: Fan
LED 14 HA (e0/1): HA
port - -
SG-6000-E5560, SG-6000-E5260 and SG-6000-E3965 have the same front panel.
The front panel consists of 4 Gigabit Ethernet ports, 4 SFP ports, 2 SFP+ ports, 1
USB port, 1 Console port, 1 Auxiliary port, 1 Management port, 1 HA port, 1 CLR
button, 4 general expansion slots, 1 fan tray, and some LED indicators.
Figure 1-4: SG-6000-E5560/E5260/E3965 Front Panel

4
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-4: SG-6000-E5560/E5260/E3965 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power
LED 8 CLR: CLR button 15
e0/ - e0/3: Gigabit
Ethernet ports (e0/2 and
e0/3 support the Bypass
function)
2 STA: Status
LED 9 CON: Console port 16 e0/4 - e0/7: SFP ports
3 ALM: Alarm
LED 10 AUX: Auxiliary port 17 xe08 - xe09: SFP+ ports
4 HA: HA
status LED 11 Fan tray 18 Slot 1: General expansion
slot
5 PS0: Power
supply PS0
LED 12 USB: USB port 19 Slot 2: General expansion
slot (not for storage
expansion module)
6 PS1: Power supply PS1
LED 13 HA: HA port 20 Slot 3: General expansion
slot (not for storage
expansion module)
7 FAN: Fan LED 14 MGT: Management
port 21 Slot 4: General expansion
slot (not for storage
expansion module)
The front panel of SG-6000-E3960 consists of 6 Gigabit Ethernet ports, 4 SFP ports,
2 SFP+ ports, 1 USB port, 1 Console port, 1 Auxiliary port, 1 Management port, 1
HA port, 1 CLR button, 2 general expansion slots and several LED indicators.
Figure 1-5: Front Panel of SG-6000-E3960

5
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-5: SG-6000-E3960 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power
LED 6 CON: Console
port 11
e0/0 - e0/5: Gigabit
Ethernet ports (e0/0 and
e0/1 supports the
Bypass function)
2 STA: Status
LED 7 AUX: Auxiliary
port 12 e0/6 - e0/9: SFP ports
3 ALM: Alarm
LED 8 USB: USB port 13 xe0/10 – xe0/11: SFP+
ports
4 HA：HA status
LED 9 MGT:
Management port 14 Slot 1: General
expansion slot
5 CLR: CLR
button 10 HA: HA port 15
Slot 2: General
expansion slot (not for
storage expansion
module)
SG-6000-E3662, SG-6000-E3660 and SG-6000-E2860 have the same front
panel.The front panel consists of 6 Gigabit Ethernet ports, 4 SFP ports, 1 USB port,
1 Console port, 1 Auxiliary port, 1 Management port, 1 HA port, 1 CLR button, 2
general expansion slots and several LED indicators.
Figure 1-6: Front Panel of SG-6000-E3662/E3660/E2860
Table 1-6: SG-6000-E3662/E3660/E2860 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power
LED 6 CON: Console
port 11 e0/0 - e0/5: Gigabit
Ethernet ports
2 STA: Status
LED 7 AUX: Auxiliary
port 12 e0/6 - e0/9: SFP ports
3 ALM: Alarm
LED 8 USB: USB port 13 Slot 1: General
expansion slot
4 HA：HA status
LED 9 MGT:
Management port 14
Slot 2: General
expansion slot (not for
storage expansion
module)
5 CLR: CLR
button 10 HA: HA port - -

6
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
SG-6000-E2800 and SG-6000-E2300 have the same front panel. The front panel
consists of 5 Gigabit Ethernet ports, 4 Combo ports (Ethernet port + SFP port), 1
USB port, 1 Console port, 1 CLR button and some LED indicators.
Figure 1-7: Front Panel of SG-6000-E2800 and SG-6000-E2300
Table 1-7: Front Panel Description of SG-6000-E2800 and SG-6000-E2300
No. Label No. Label No. Label
1 PWR:
Power LED 5 e0/0 - e0/8: Gigabit
Ethernet port status
LED 9 USB: USB port
2 STA:
Status LED 6 e0/5 - e0/8: SFP
interface LED 10 e0/0 - e0/4: Gigabit
Ethernet ports
3 ALM:
Alarm LED 7 CLR: CLR button 11 e0/0 - e0/4: Combo ports
(Ethernet port + SFP
port)
4 HA: HA
status LED 8 CON: Console port - -
SG-6000-E1700 and SG-6000-E1606 have the same front panel. The front panel
consists of 9 Gigabit Ethernet ports, 1 USB port, 1 Console port, 1 CLR button and
some LED indicators.
Figure 1-8: SG-6000-E1700/E1606 Front Panel
Table 1-8: SG-6000-E1700/E1606 Front Panel Description
No. Label No. Label No. Label
1 PWR:
Power LED 4 HA: HA status LED 7 CON: Console port
2 STA:
Status LED 5 e0/0 - e0/4: Gigabit
Ethernet port status LED 8 USB: USB port
3 ALM: Alarm
LED 6 CLR: CLR button 9 e0/0 - e0/4: Gigabit
Ethernet ports

7
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
The front panel of SG-6000-E1600 consists of some LED indicators.
Figure 1-9: SG-6000-E1600 Front Panel
Table 1-9: SG-6000-E1600 Front Panel Description
No. Label No. Label No. Label
1 PWR: Power LED 3 STA: Status LED - -
2 ALM: Alarm LED 4 e0/0 - e0/8: Gigabit Ethernet
port status LED - -
The front panel of SG-6000-E1100 (WLAN version) consists of some LED indicators.
Figure 1-10: Front Panel of SG-6000-E1100 (WLAN version)
Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version)
No. Label No. Label No. Label
1 PWR: Power
LED 3 STA: Status LED 5 WLAN: WLAN
LED
2 ALM: Alarm
LED 4 e0/0 - e0/8: Gigabit Ethernet
port status LED - -
The front panel of SG-6000-E1100 (WLAN+3G version) consists of some LED
indicators.

8
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Figure 1-11: Front Panel of SG-6000-E1100 (WLAN+3G version)
Table 1-11: Front Panel Description of SG-6000-E1100 (WLAN+3G version)
No. Label No. Label No. Label
1 PWR: Power
LED 3 STA: Status LED 5 3G: 3G LED
2 ALM: Alarm
LED 4 e0/0 - e0/8: Gigabit Ethernet
port status LED 6 WLAN: WLAN
LED
Back Panel
SG-6000-E6360 and SG-6000-E6160 have the same back panel layout. The back
panel layout of SG-6000-E6360/E6160 consists of 2 power supply sockets, 2
expansion slots, 1 grounding screw and 1 anti-dust mesh.
Figure 1-12: SG-6000-E6360/E6160 Back Panel
SG-6000-E5960 ,SG-6000-E5760 and SG-6000-E5660 have the same back panel
layout. The back panel layout of SG-6000-E5960/E5760/E5660 consists of 2 power
supply sockets, 1 grounding screw. The standard product of SG-6000-
E5960/E5760/E5660 adopts dual power supplies and it is also available in single
power supply.

9
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Figure 1-13: SG-6000-E5960/E5760/E5660 Back Panel
SG-6000-E5560 SG-6000-E5260 and SG-6000-E3965 have the same back panel
The back panel consists of 2 power supply sockets, 1 grounding screw and 1 anti-
dust mesh. The standard product of SG-6000-E5560/E5260/E3965 adopts dual
power supplies and it is also available in single power supply.
Figure 1-14: SG-6000-E5560/E5260/E3965 Back Panel
SG-6000-E3960, SG-6000-E3662, SG-6000-E3660, SG-6000-E2860, SG-6000-
E2800, SG-6000-E2300, SG-6000-E1700 and SG-6000-E1606 have the same back
panel layout. The standard products SG-6000-E2800, SG-6000-E2300, SG-6000-
E1700 and SG-6000-E1606 adopt single power supply and they are also available in
dual power supplies. The back panel of single power supply product has 1 power
supply socket, 1 power supply switch and 1 grounding screw. Figure 1-13 illustrates
the back panel of these models.
Figure 1-15: Back Panel of SG-6000-
E3960/E3662/E3660/E2860/E2800/E2300/E1700/E1606
SG-6000-E1600 uses the power adapter. The back panel of SG-6000-E1600 has 1
power supply socket, 1 Console port, 1 CLR button, 9 Gigabyte Ethernet ports, 1
USB port, 1 grounding screw, and 1 security keyhole.
Figure 1-16: SG-6000-E1600 Back Panel

10
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-12: Back Panel Description of SG-6000-E1600
No. Label No. Label No. Label
1 DC POWER: DC
power interface 3 CON: Console port 5 e0/0 - e0/8: Gigabit
Ethernet port
2 CLR：CLR
button 4 USB: USB port 6 Security keyhole
SG-6000-E1100 (WLAN version) uses the power adapter. The back panel of SG-
6000-E1100 (WLAN version) has 1 power supply socket, 1 Console port, 1 CLR
button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security
keyhole, and 2 SMA connectors for WLAN antennas. Figure 1-15 illustrates the back
panel of this model.
Figure 1-17: SG-6000-E1100 (WLAN version) Back Panel
Table 1-13: Back Panel Description of SG-6000-E1100 (WLAN version)
No. Label No. Label No. Label
1 DC POWER: DC
power interface 4 SMA connectors for
WLAN antennas 7 Security keyhole
2 CLR：CLR
button 5 USB: USB port - -
3 CON: Console
port 6 e0/0 - e0/8: Gigabit
Ethernet port - -

11
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
SG-6000-E1100 (WLAN+3G version) uses the power adapter. The back panel of
SG-6000-E1100 (WLAN+3G version) has 1 power supply socket, 1 Console port, 1
CLR button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security
keyhole, 2 SMA connectors for 3G antennas, and 2 SMA connectors for WLAN
antennas.
Figure 1-18: SG-6000-E1100 (WALN+3G version) Back Panel
Table 1-14: Back Panel Description of SG-6000-E1100 (WLAN+3G version)
No. Label No. Label No. Label
1 SMA connector
for 3G antenna 5 SIM: SIM card slot 9 Security keyhole
2 DC POWER: DC
power interface 6 SMA connectors for
WLAN antennas 10 SMA connector for
3G antenna
3 CLR：CLR
button 7 USB: USB port - -
4 CON: Console
port 8 e0/0 - e0/8: Gigabit
Ethernet port - -
LED Indicators
The following table describes the meanings of LED indicators on the front panels of
Hillstone devices.
Table 1-15: Front Panel LED Descriptions
LED Color/Status Description
PWR
Green/Always
on The device power is running normally.
Orange/Always
on The device power is running abnormally.
Red/Always on Power failure so the system is down.
Off The device is powered off.
STA Green/Always
on The system is booting.

12
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Green/Blinking The system is running normally.
Red/Always on The system has failed to boot or has an error.
ALM
Red/Always on The system is sending alarm(s).
Green/Blinking The system is waiting.
Orange/Blinking The system is using a trial license.
Orange/Always
on The trial license has expired and there is no legitimate license installed in the system.
Off The system is running normally.
PS0
Green/Always
on Power Supply PS0 is running normally.
Orange/Always
on Power Supply PS0 is running normally, but its fan has failed. Change the power supply immediately.
Off Power Supply PS0 is powered off or has failed.
PS1
Green/Always
on Power Supply PS1 is running normally.
Orange/Always
on Power Supply PS1 is running normally, but its fan has failed. Change the power supply immediately.
Off Power Supply PS0 is powered off or has failed.
HA
Green/Always
on Not using HA, this device is the master device.
Green/Blinking Two devices are in an HA cluster. This device is
working as the master.
Orange/Blinking Two devices are in an HA cluster. This device is
working as the slave.
Red/Blinking HA function has failed.
Off High Availability is disabled.
FAN
Green/Always
on The cooling system is running normally.
Orange/Always
on
One of the fans has failed, but the cooling system can
still fully function. Change the fan tray as soon as
possible.
Red/Always on The cooling system has a serious error or the fan tray
is not fully inserted. The system will automatically
shut down in 15 seconds.
VPN
Green/Always
on The VPN tunnel is connected.
Orange/Always
on VPN is turned on but no tunnel is connected.
Off VPN is not in use.
SD
Green/Always
on SD card has been inserted and is in normal status.
Green/Blinking SD card is transmitting data.
Off No SD card is inserted.
LNK
Green/Always
on
The link between this port and its peer device is in
normal status.
Off
The link between this port and its peer device has
failed.

13
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
ACT Orange/Blinking The port is sending or receiving data.
Off No data is transmitted on this port.
e0/0-
e0/8
Green/Always
on
The link between this port and its peer device is in
normal status.
Green/Blinking The port is sending or receiving data.
Off There is no connection between this port with the its
peer device, or the link between this port and its peer
device fails.
3G Green/Always
on The device discovers the built-in 3G Express module.
Green/Blinking The 3G module is sending or receiving data.
WLAN Green/Always
on The device discovers the built-in WLAN module.
Green/Blinking The WLAN module is sending or receiving data.
Notes:
♦The STA and ALM LEDs will both turn red when there is a boot failure
caused by OS software damage. Contact your sales representative if this
occurs.
♦As the number and type of LED indicators may vary from different product
models, please refer to the actual product.
System Parameters
The following table lists the system parameters of Hillstone devices of all models.
Table 1-16: System Parameters
Item Description
Fixed Ports SG-6000-E6360
2 Gigabit Ethernet ports
8 SFP+ ports
2 QSFP+ ports
1 USB 2.0 Host port
1 MGT port
1 HA port
1 Console port
1 Auxiliary port