Hillstone SG-6000 E Series Operating and maintenance manual

Hillstone StoneOS User Manual
Hillstone SG-6000 E-Series Hardware
Reference Guide
www.hillstonenet.com
TWNO: TW-HW-ES-EN-V5.4-Y20M05

2
Name and Concentration of Toxic or Hazardous Substances and Elements in Products | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Name and Concentration of Toxic or Hazardous
Substances and Elements in Products
Component
Toxic or hazardous substances and elements
Lead
Mercury
Cadmium
Cr6+
PBB
PDBE
Metal parts
(including fasteners)
Χ
O
O
O
O
O
Printed circuit board
assemblies and
components
Χ
O
O
O
O
O
Cables and cable
assemblies
Χ
O
O
O
O
O
Plastics and Polymers
Χ
O
O
O
Χ
Χ
Electric components
other than circuit
boards
Χ
O
O
O
O
O
O: Indicates that this toxic or hazardous substance in the material is below the
limit requirement defined in Requirements for Concentration Limits for Certain
Hazardous Substances in Electronic Information Products (SJ/T11363-2006) issued
by Ministry of Information Industry of PRC.
Χ:Indicates that this toxic or hazardous substance in the material exceeds the limit
requirement specified in Requirements for Concentration Limits for Certain
Hazardous Substances in Electronic Information Products (SJ/T11363-2006) issued
by Ministry of Information Industry of PRC.
Note: Not all components in the table are included in one product.
This symbol indicates the environment friendly use period of all products
and components. The period applies only to the normal operation
conditions specified in this guide.

3
Preface | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Preface
About This Guide
Thanks for choosing the network security products from Hillstone Networks.
This document is an installation guide for Hillstone devices to help you install the
Hillstone device properly.
This guide includes the following chapters:
Chapter 1. Introduction
Chapter 2. Installation Preparations
Chapter 3. Installation
Chapter 4. Boot and Configuration
Chapter 5. Hardware Maintenance and Replacement
Chapter 6. Troubleshooting
Appendix: Supported Versions of Devices
Addendum FCC Statement
Document Conventions
This guide uses the following conventions for your convenience to read and
understand:
Warning: Indicates improper operation that may cause serious damage to
equipment or injury to operators. Thus, operators must strictly follow the
operation rules.
Caution: Indicates incorrect operation that may affect the normal use of the
equipment. Operators should be careful.
Note: Indicates information that may help readers understand the content.

4
Table of Contents | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table of Contents
HILLSTONE SG-6000 E-SERIES HARDWARE REFERENCE GUIDE.............................................................1
NAME AND CONCENTRATION OF TOXIC OR HAZARDOUS SUBSTANCES AND ELEMENTS IN PRODUCTS .....................2
PREFACE..................................................................................................................................................................3
ABOUT THIS GUIDE..............................................................................................................................................................3
DOCUMENT CONVENTIONS....................................................................................................................................................3
TABLE OF CONTENTS................................................................................................................................................4
LIST OF FIGURES ......................................................................................................................................................6
LIST OF TABLES ........................................................................................................................................................7
CHAPTER 1 INTRODUCTION .....................................................................................................................................1
OVERVIEW .........................................................................................................................................................................1
HARDWARE OVERVIEW.........................................................................................................................................................1
Front Panel.................................................................................................................................................................. 1
Back Panel................................................................................................................................................................... 9
LED Indicators ........................................................................................................................................................... 13
System Parameters ................................................................................................................................................... 15
Ports.......................................................................................................................................................................... 20
CLR Button ................................................................................................................................................................ 26
Expansion Slot........................................................................................................................................................... 27
Power Supply ............................................................................................................................................................ 27
Hard Disk Modules.................................................................................................................................................... 29
Expansion Modules ................................................................................................................................................... 30
Cooling System ................................................................................................................................................... 30
CHAPTER 2 INSTALLATION PREPARATIONS............................................................................................................. 32
INTRODUCTION .................................................................................................................................................................32
CLEANNESS REQUIREMENTS................................................................................................................................................. 32
ESD PREVENTION..............................................................................................................................................................32
EMI PREVENTION..............................................................................................................................................................32
GROUNDING REQUIREMENTS...............................................................................................................................................33
WORKBENCH REQUIREMENTS .............................................................................................................................................. 33
OTHER SAFETY RECOMMENDATIONS ..................................................................................................................................... 33
UNPACKING......................................................................................................................................................................33
INSTALLATION DEVICES/TOOLS/CABLES .................................................................................................................................33
CHAPTER 3 INSTALLATION ..................................................................................................................................... 35
BEFORE INSTALLATION........................................................................................................................................................35
INSTALLING THE DEVICE ON A WORKBENCH ............................................................................................................................ 35
INSTALLING THE DEVICE ON A RACK.......................................................................................................................................36
CONNECTING CABLES ......................................................................................................................................................... 37
Connecting the Ground Wire .................................................................................................................................... 38
Connecting the Console Cable................................................................................................................................... 38

5
Table of Contents | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Connecting the Ethernet Cable ................................................................................................................................. 38
Connecting an AC Power Cable................................................................................................................................. 40
Connecting a DC Power Cable................................................................................................................................... 41
Connecting a Power Adapter .................................................................................................................................... 42
INSTALLING AN ANTENNA .................................................................................................................................................... 42
INSTALLING THE SIM CARD.................................................................................................................................................. 43
VERIFYING INSTALLATION ....................................................................................................................................................43
CHAPTER 4 BOOT AND CONFIGURATION................................................................................................................ 44
INTRODUCTION .................................................................................................................................................................44
ESTABLISHING A CONFIGURATION ENVIRONMENT .................................................................................................................... 44
Console (CON) Connection ........................................................................................................................................ 44
WebUI ....................................................................................................................................................................... 45
Tenet and SSH ........................................................................................................................................................... 46
BASIC CONFIGURATION.......................................................................................................................................................46
CHAPTER 5 HARDWARE MAINTENANCE AND REPLACEMENT.................................................................................. 47
INTRODUCTION .................................................................................................................................................................47
INSTALLING AND REMOVING THE POWER SUPPLY MODULE........................................................................................................47
INSTALLING AND REMOVING THE EXPANSION MODULE .............................................................................................................48
INSTALLING AND REMOVING THE FAN TRAY ............................................................................................................................ 48
INSTALLING AND REMOVING THE ANTI-DUST MESH..................................................................................................................49
INSTALLING AND REMOVING THE HARD DISK MODULE..............................................................................................................50
CHAPTER 6 TROUBLESHOOTING............................................................................................................................. 53
INTRODUCTION .................................................................................................................................................................53
LOSING THE ADMINISTRATOR PASSWORD...............................................................................................................................53
TROUBLESHOOTING POWER SYSTEM ..................................................................................................................................... 53
TROUBLESHOOTING THE CONFIGURATION SYSTEM ...................................................................................................................53
APPENDIX: SUPPORTED VERSIONS OF DEVICES ...................................................................................................... 54
ADDENDUM FCC STATEMENT ................................................................................................................................ 58
COPYRIGHT INFORMATION..................................................................................................................... 61

6
List of Figures | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
List of Figures
Figure 1-1：SG-6000-E6360 Front Panel ....................................................................1
Figure 1-2: SG-6000-E6160 Front Panel.....................................................................2
Figure 1-3：SG-6000-E5960 Front Panel ....................................................................3
Figure 1-4: SG-6000-E5560 Front Panel.....................................................................3
Figure 1-5: Front Panel of SG-6000-E3960 .................................................................4
Figure 1-6: Front Panel of SG-6000-E3662 .................................................................5
Figure 1-7: Front Panel of SG-6000-E2800 .................................................................6
Figure 1-8: SG-6000-E1700 Front Panel.....................................................................6
Figure 1-9: SG-6000-E1600 Front Panel.....................................................................7
Figure 1-10: Front Panel of SG-6000-E1100 (WLAN version).........................................7
Figure 1-12: Front Panel of SG-6000-E1100 (4G version) .............................................8
Figure 1-13: Front Panel of SG-6000-E1100 (WLAN+4G version)...................................8
Figure 1-14: SG-6000-E6360 Back Panel ...................................................................9
Figure 1-15: SG-6000-E5960 Back Panel ................................................................. 10
Figure 1-16: SG-6000-E5560 Back Panel ................................................................. 10
Figure 1-17: Back Panel of SG-6000-E3960.............................................................. 10
Figure 1-18: SG-6000-E1600 Back Panel ................................................................. 10
Figure 1-19: SG-6000-E1100 (WLAN version) Back Panel ........................................... 11
Figure 1-21: SG-6000-E1100 (4G version) Back Panel ............................................... 12
Figure 1-23: AC Power Module................................................................................ 29
Figure 1-24: DC Power Module ............................................................................... 29
Figure 3-1: Installing the Rubber Pads..................................................................... 35
Figure 3-2: Installing the Floating Nuts .................................................................... 36
Figure 3-3: Installing the Rack-mounting Ears (1U Chassis as example) ....................... 37
Figure 3-4: Installing the Device in a Rack (1U Chassis as example) ............................ 37
Figure 3-5: Connecting the Ground Wire (1U Chassis as example) ............................... 38
Figure 3-6: Connecting the Ethernet Copper Cable .................................................... 39
Figure 3-7: Connecting the Ethernet Fiber Cable ....................................................... 40
Figure 3-8: Connecting an AC Power Cable............................................................... 41
Figure 3-9: Connecting a DC Power Cable ................................................................ 42
Figure 3-10: 3 WLAN and 4G Antennas .................................................................... 42
Figure 4-1: Console Port Configuration .................................................................... 44
Figure 4-2: Setting Parameters for the Terminal Session ............................................ 45
Figure 5-1: Installing Power Supply Module .............................................................. 47
Figure 5-2: Pulling Anti-dust Mesh Out..................................................................... 49
Figure 5-3: Removing the Blank Panel ..................................................................... 50
Figure 5-4: Placing the Hard Disk Module ................................................................. 51
Figure 5-5: Fixing the Hard Disk Module................................................................... 51
Figure 5-6: Installing the Blank Panel ...................................................................... 52

7
List of Tables | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
List of Tables
Table 1-1: SG-6000-E6360 Front Panel Description.................................................................................................... 2
Table 1-2: SG-6000-E6160 Front Panel Description.................................................................................................... 2
Table 1-3: SG-6000-E5960 Front Panel Description.................................................................................................... 3
Table 1-4: SG-6000-E5560 Front Panel Description.................................................................................................... 4
Table 1-5: SG-6000-E3960 Front Panel Description.................................................................................................... 5
Table 1-6: SG-6000-E3662 Front Panel Description.................................................................................................... 5
Table 1-7: Front Panel Description of SG-6000-E2800 and SG-6000-E2300 ............................................................... 6
Table 1-8: SG-6000-E1700 Front Panel Description.................................................................................................... 7
Table 1-9: SG-6000-E1600 Front Panel Description.................................................................................................... 7
Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version) .................................................................... 8
Table 1-12: Front Panel Description of SG-6000-E1100 (4G version).......................................................................... 8
Table 1-13: Front Panel Description of SG-6000-E1100 (WLAN+4G version).............................................................. 9
Table 1-14: Back Panel Description of SG-6000-E1600............................................................................................. 11
Table 1-15: Back Panel Description of SG-6000-E1100 (WLAN version)................................................................... 11
Table 1-17: Back Panel Description of SG-6000-E1100 (4G version)......................................................................... 12
Figure 1-22: SG-6000-E1100 (WLAN+4G version) Back Panel .................................................................................. 13
Table 1-18: Back Panel Description of SG-6000-E1100 (WLAN+4G version)............................................................. 13
Table 1-19: Front Panel LED Descriptions ................................................................................................................. 13
Table 1-20: System Parameters ................................................................................................................................ 15
Table 1-21: Console Port Attributes.......................................................................................................................... 20
Table 1-22: Auxiliary Port Attributes......................................................................................................................... 20
Table 1-23: USB Port Attributes ................................................................................................................................ 21
Table 1-24: Gigabit Copper Port Attributes .............................................................................................................. 21
Table 1-25: SFP Port Attributes................................................................................................................................. 21
Table 1-26: SFP Optical Module Attributes............................................................................................................... 22
Table 1-27: SFP Copper Module Attributes............................................................................................................... 23
Table 1-28: SFP+ Port Attributes............................................................................................................................... 23
Table 1-29: SFP+ Optical Module Attributes............................................................................................................. 24
Table 1-30: QSFP+ Port Attributes ............................................................................................................................ 24
Table 1-31: QSFP+ Optical Module Attributes .......................................................................................................... 25
Table 1-32: XFP Port Attributes................................................................................................................................. 25
Table 1-33: XFP Optical Module Attributes............................................................................................................... 26
Table 1-34: Power Supplies of All Product Models.................................................................................................... 28
Table 1-35: Power Supply Module LED Descriptions................................................................................................. 29
Table 1-36: Platforms and Default Storage Capacity................................................................................................ 30
Table 2-1: Dust Concentration Requirements in the Equipment Room .................................................................... 32

1
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Chapter 1 Introduction
Overview
Hillstone SG-6000 series product models include SG-6000-E6368,SG-6000-E6360,
SG-6000-E6168,SG-6000-E6160, SG-6000-E5960, SG-6000-E5760, SG-6000-
E5568, SG-6000-E5660, SG-6000-E5268,SG-6000-E5260, SG-6000-E5168,SG-
6000-E3965, SG-6000-E3968, SG-6000-E3960, SG-6000-E3668, SG-6000-E3662,
SG-6000-E3660, SG-6000-E2868, SG-6000-E2860, SG-6000-E2800, SG-6000-
E2300, SG-6000-E1700, SG-6000-E1606, SG-6000-E1600, SG-6000-E1100 (WLAN
version), SG-6000-E1100 (4G version), and SG-6000-E1100 (WLAN+4G version).
SG-6000-E6368, SG-6000-E6360, SG-6000-E6168,SG-6000-E6160, SG-6000-
E5960, SG-6000-E5760, SG-6000-E5568, SG-6000-E5660, SG-6000-E5268, SG-
6000-E5260, SG-6000-E5168, SG-6000-E3965, SG-6000-E3968,SG-6000-E3960,
SG-6000-E3668, SG-6000-E3662, SG-6000-E3660, SG-6000-E2868 and SG-6000-
E2860 adopt modular design of hot-swappable circuit boards. For more information
about extensible modules, please see Hillstone SG-6000 M_G_E Series Expansion
Modules Reference Guide.
For the supported versions of the devices, refer to Supported Versions of Devices
Hardware Overview
Hillstone devices are designed to fit in standard 19-inch cabinets/racks. A device
can be installed in a cabinet/rack or placed on a workbench.
Front Panel
The front panel of SG-6000-E6368 and SG-6000-E6360 consists of 2 Gigabit
Ethernet ports, 8 SFP+ ports, 2 QSFP+ports, 1 USB port, 1 HA port, 1 Management
port, 1 Console port, 1 Auxiliary port, 1 CLR button, 1 Bypass expansion slot and
several LED indicators.
Figure 1-1：SG-6000-E6360 Front Panel

2
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-1: SG-6000-E6360 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power LED
7
FAN: Fan LED
13
HA: HA port
2
STA: Status LED
8
CLR: CLR button
14
e0/0 - e0/1: Gigabit
Ethernet ports
3
ALM: Alarm LED
9
CON: Console
port
15
XLe0/2-XLe0/3:
QSFP+ ports
4
HA: HA status
LED
10
AUX: Auxiliary
port
16
Bypass expansion slot
5
PS0: Power
supply PS0 LED
11
USB: USB port
17
Xe0/4-Xe0/11: SFP+
ports
6
PS1: Power
supply PS1 LED
12
MGT:
Management port
18
Fan tray
The front panel of SG-6000-E6168 and SG-6000-E6160 consists of 2 Gigabit
Ethernet ports, 8 SFP+ ports, 1 USB port, 1 HA port, 1 Management port, 1 Console
port, 1 Auxiliary port, 1 CLR button, 1 Bypass expansion slot and several LED
indicators.
Figure 1-2: SG-6000-E6160 Front Panel
Table 1-2: SG-6000-E6160 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power LED
7
FAN: Fan LED
13
HA: HA port
2
STA: Status LED
8
CLR: CLR button
14
e0/0 - e0/1: Gigabit
Ethernet ports
3
ALM: Alarm LED
9
CON: Console
port
15
Bypass expansion slot
4
HA: HA status
LED
10
AUX: Auxiliary
port
16
Xe0/2-Xe0/9: SFP+
ports
5
PS0: Power
supply PS0 LED
11
USB: USB port
17
Fan tray
6
PS1: Power
supply PS1 LED
12
MGT:
Management port
18

3
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
SG-6000-E5960, SG-6000-E5760 and SG-600-E5660 have the same front panel.
The front panel consist of 4 Gigabit Ethernet ports, 4 SFP ports, 1 USB port, 1 HA
port, 1 Management port, 1 Console port, 1 Auxiliary port, 1 CLR button, 4 general
expansion slots and several LED indicators. The standard power supply for SG-
6000-E5960/E5760 is dual power supplies, and the product with single power
supply is also available.
Figure 1-3：SG-6000-E5960 Front Panel
Table 1-3: SG-6000-E5960 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
8
CLR: CLR button
15
e0/2 - e0/5: Gigabit
Ethernet ports
2
STA: Status
LED
9
CON: Console
port
16
e0/6 - e0/9: SFP ports
3
ALM: Alarm
LED
10
AUX: Auxiliary
port
17
Slot 1: General expansion
slot
4
HA: HA
status LED
11
Fan tray
18
Slot 2: General expansion
slot (not for storage
expansion module)
5
PS0: Power
supply PS0
LED
12
USB: USB port
19
Slot 3: General expansion
slot (not for storage
expansion module)
6
PS1: Power
supply PS1
LED
13
MGT (e0/0):
Management port
20
Slot 4: General expansion
slot (not for storage
expansion module)
7
FAN: Fan
LED
14
HA (e0/1): HA
port
-
-
SG-6000-E5568, SG-6000-E5560, SG-6000-E5268, SG-6000-E5260, SG-6000-
E5168 and SG-6000-E3965 have the same front panel. The front panel consists of 4
Gigabit Ethernet ports, 4 SFP ports, 2 SFP+ ports, 1 USB port, 1 Console port, 1
Auxiliary port, 1 Management port, 1 HA port, 1 CLR button, 4 general expansion
slots, 1 fan tray, and some LED indicators.
Figure 1-4: SG-6000-E5560 Front Panel

4
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-4: SG-6000-E5560 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
8
CLR: CLR button
15
e0/ - e0/3: Gigabit
Ethernet ports (e0/2 and
e0/3 support the Bypass
function)
2
STA: Status
LED
9
CON: Console port
16
e0/4 - e0/7: SFP ports
3
ALM: Alarm
LED
10
AUX: Auxiliary port
17
xe08 - xe09: SFP+ ports
4
HA: HA
status LED
11
Fan tray
18
Slot 1: General expansion
slot
5
PS0: Power
supply PS0
LED
12
USB: USB port
19
Slot 2: General expansion
slot (not for storage
expansion module)
6
PS1: Power
supply PS1
LED
13
HA: HA port
20
Slot 3: General expansion
slot (not for storage
expansion module)
7
FAN: Fan LED
14
MGT: Management
port
21
Slot 4: General expansion
slot (not for storage
expansion module)
The front panel of SG-6000-E3968 and SG-6000-E3960 consists of 6 Gigabit
Ethernet ports, 4 SFP ports, 2 SFP+ ports, 1 USB port, 1 Console port, 1 Auxiliary
port, 1 Management port, 1 HA port, 1 CLR button, 2 general expansion slots and
several LED indicators.
Figure 1-5: Front Panel of SG-6000-E3960

5
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-5: SG-6000-E3960 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
6
CON: Console
port
11
e0/0 - e0/5: Gigabit
Ethernet ports (e0/0 and
e0/1 supports the
Bypass function)
2
STA: Status
LED
7
AUX: Auxiliary
port
12
e0/6 - e0/9: SFP ports
3
ALM: Alarm
LED
8
USB: USB port
13
xe0/10 –xe0/11: SFP+
ports
4
HA:HA status
LED
9
MGT:
Management port
14
Slot 1: General
expansion slot
5
CLR: CLR
button
10
HA: HA port
15
Slot 2: General
expansion slot (not for
storage expansion
module)
SG-6000-E3668, SG-6000-E3662, SG-6000-E3660, SG-6000-E2868 and SG-6000-
E2860 have the same front panel. The front panel consists of 6 Gigabit Ethernet
ports, 4 SFP ports, 1 USB port, 1 Console port, 1 Auxiliary port, 1 Management
port, 1 HA port, 1 CLR button, 2 general expansion slots and several LED indicators.
Figure 1-6: Front Panel of SG-6000-E3662
Table 1-6: SG-6000-E3662 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
6
CON: Console
port
11
e0/0 - e0/5: Gigabit
Ethernet ports
2
STA: Status
LED
7
AUX: Auxiliary
port
12
e0/6 - e0/9: SFP ports
3
ALM: Alarm
LED
8
USB: USB port
13
Slot 1: General
expansion slot
4
HA: HA status
LED
9
MGT:
Management port
14
Slot 2: General
expansion slot (not for
storage expansion
module)
5
CLR: CLR
button
10
HA: HA port
-
-

6
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
SG-6000-E2800 and SG-6000-E2300 have the same front panel. The front panel
consists of 5 Gigabit Ethernet ports, 4 Combo ports (Ethernet port + SFP port), 1
USB port, 1 Console port, 1 CLR button and some LED indicators.
Figure 1-7: Front Panel of SG-6000-E2800
Table 1-7: Front Panel Description of SG-6000-E2800 and SG-6000-E2300
No.
Label
No.
Label
No.
Label
1
PWR:
Power LED
5
e0/0 - e0/8: Gigabit
Ethernet port status
LED
9
USB: USB port
2
STA:
Status
LED
6
e0/5 - e0/8: SFP
interface LED
10
e0/0 - e0/4: Gigabit
Ethernet ports
3
ALM:
Alarm LED
7
CLR: CLR button
11
e0/0 - e0/4: Combo
ports (Ethernet port +
SFP port)
4
HA: HA
status LED
8
CON: Console port
-
-
SG-6000-E1700 and SG-6000-E1606 have the same front panel. The front panel
consists of 9 Gigabit Ethernet ports, 1 USB port, 1 Console port, 1 CLR button and
some LED indicators.
Figure 1-8: SG-6000-E1700 Front Panel

7
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-8: SG-6000-E1700 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR:
Power LED
5
PS0: Power supply PS0
LED
9
CON: Console port
2
STA: Status
LED
6
PS1: Power supply PS1
LED
10
USB: USB port
3
ALM: Alarm
LED
7
e0/0 - e0/8: Gigabit
Ethernet port status LED
11
e0/0 - e0/8: Gigabit
Ethernet ports
4
HA: HA
status LED
8
CLR: CLR button
The front panel of SG-6000-E1600 consists of some LED indicators.
Figure 1-9: SG-6000-E1600 Front Panel
Table 1-9: SG-6000-E1600 Front Panel Description
No.
Label
No.
Label
No.
Label
1
PWR: Power LED
3
STA: Status LED
-
-
2
ALM: Alarm LED
4
e0/0 - e0/8: Gigabit Ethernet
port status LED
-
-
The front panel of SG-6000-E1100 (WLAN version) consists of some LED indicators.
Figure 1-10: Front Panel of SG-6000-E1100 (WLAN version)

8
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-10: Front Panel Description of SG-6000-E1100 (WLAN version)
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
3
STA: Status LED
5
WLAN:
WLAN LED
2
ALM: Alarm
LED
4
e0/0 - e0/8: Gigabit Ethernet
port status LED
-
-
The front panel of SG-6000-E1100 (4G version) consists of some LED indicators.
Figure 1-12: Front Panel of SG-6000-E1100 (4G version)
Table 1-12: Front Panel Description of SG-6000-E1100 (4G version)
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
3
STA: Status LED
5
4G: 4G
LED
2
ALM: Alarm
LED
4
e0/0 - e0/8: Gigabit Ethernet
port status LED
-
-
The front panel of SG-6000-E1100 (WLAN+4G version) consists of some LED
indicators.
Figure 1-13: Front Panel of SG-6000-E1100 (WLAN+4G version)

9
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-13: Front Panel Description of SG-6000-E1100 (WLAN+4G version)
No.
Label
No.
Label
No.
Label
1
PWR: Power
LED
3
STA: Status LED
5
4G: 4G LED
2
ALM: Alarm
LED
4
e0/0 - e0/8: Gigabit Ethernet
port status LED
6
WLAN:
WLAN LED
Back Panel
SG-6000-E6368, SG-6000-E6360, SG-6000-E6168 and SG-6000-E6160 have the
same back panel layout. The back panel layout of SG-6000-E6368, SG-6000-
E6360, SG-6000-E6168 and SG-6000-E6160 consists of 2 power supply sockets, 2
expansion slots, 1 grounding screw and 1 anti-dust mesh.
Figure 1-14: SG-6000-E6360 Back Panel
SG-6000-E5960, SG-6000-E5760 and SG-6000-E5660 have the same back panel
layout. The back panel layout of SG-6000-E5960/E5760/E5660 consists of 2 power
supply sockets, 1 grounding screw. The standard product of SG-6000-
E5960/E5760/E5660 adopts dual power supplies and it is also available in single
power supply.

10
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Figure 1-15: SG-6000-E5960 Back Panel
SG-6000-E5568, SG-6000-E5560, SG-6000-E5268, SG-6000-E5260, SG-6000-
E5168 and SG-6000-E3965 have the same back panel. The back panel consists of 2
power supply sockets, 1 grounding screw and 1 anti-dust mesh. The standard
product of SG-6000- E5568/E5560/E5268/E5260/E5158/E3965 adopts dual power
supplies and it is also available in single power supply.
Figure 1-16: SG-6000-E5560 Back Panel
SG-6000-E3968, SG-6000-E3960, SG-6000-E3668, SG-6000-E3662, SG-6000-
E3660, SG-6000-E2868, SG-6000-E2860, SG-6000-E2800, SG-6000-E2300, SG-
6000-E1700 and SG-6000-E1606 have the same back panel layout. The standard
products SG-6000-E2800, SG-6000-E2300, SG-6000-E1700 and SG-6000-E1606
adopt single power supply and they are also available in dual power supplies. The
back panel of single power supply product has 1 power supply socket, 1 power
supply switch and 1 grounding screw. Figure 1-15 illustrates the back panel of
these models.
Figure 1-17: Back Panel of SG-6000-E3960
SG-6000-E1600 uses the power adapter. The back panel of SG-6000-E1600 has 1
power supply socket, 1 Console port, 1 CLR button, 9 Gigabyte Ethernet ports, 1
USB port, 1 grounding screw, and 1 security keyhole.
Figure 1-18: SG-6000-E1600 Back Panel

11
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Table 1-14: Back Panel Description of SG-6000-E1600
No.
Label
No.
Label
No.
Label
1
DC POWER: DC
power interface
3
CON: Console port
5
e0/0 - e0/8: Gigabit
Ethernet port
2
CLR: CLR button
4
USB: USB port
6
Security keyhole
SG-6000-E1100 (WLAN version) uses the power adapter. The back panel of SG-
6000-E1100 (WLAN version) has 1 power supply socket, 1 Console port, 1 CLR
button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security
keyhole, and 2 SMA connectors for WLAN antennas. Figure 1-15 illustrates the back
panel of this model.
Figure 1-19: SG-6000-E1100 (WLAN version) Back Panel
Table 1-15: Back Panel Description of SG-6000-E1100 (WLAN version)
No.
Label
No.
Label
No.
Label
1
DC POWER: DC
power interface
4
SMA connectors for
WLAN antennas
7
Security keyhole
2
CLR: CLR button
5
USB: USB port
-
-
3
CON: Console
port
6
e0/0 - e0/8: Gigabit
Ethernet port
-
-

12
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
SG-6000-E1100 (4G version) uses the power adapter. The back panel of SG-6000-
E1100 (4G version) has 1 power supply socket, 1 Console port, 1 CLR button, 9
Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security keyhole, and 2
SMA connectors for 4G antennas.
Figure 1-21: SG-6000-E1100 (4G version) Back Panel
Table 1-17: Back Panel Description of SG-6000-E1100 (4G version)
No.
Label
No.
Label
No.
Label
1
SMA connector
for 4G antenna
4
CON: Console port
7
e0/0 - e0/8: Gigabit
Ethernet port
2
DC POWER: DC
power interface
5
SIM: SIM card slot
8
Security keyhole
3
CLR: CLR button
6
USB: USB port
9
SMA connector for
4G antenna
SG-6000-E1100 (WLAN+4G version) uses the power adapter. The back panel of
SG-6000-E1100 (WLAN+4G version) has 1 power supply socket, 1 Console port, 1
CLR button, 9 Gigabyte Ethernet ports, 1 USB port, 1 grounding screw, 1 security
keyhole, 2 SMA connectors for 4G antennas, and 2 SMA connectors for WLAN
antennas.

13
Chapter 1 Introduction | Hillstone
Hillstone SG-6000 E-Series Hardware Reference Guide
Figure 1-22: SG-6000-E1100 (WLAN+4G version) Back Panel
Table 1-18: Back Panel Description of SG-6000-E1100 (WLAN+4G version)
No.
Label
No.
Label
No.
Label
1
SMA connector
for 4G antenna
5
SIM: SIM card slot
9
Security keyhole
2
DC POWER: DC
power interface
6
SMA connectors for
WLAN antennas
10
SMA connector for
4G antenna
3
CLR: CLR button
7
USB: USB port
-
-
4
CON: Console
port
8
e0/0 - e0/8: Gigabit
Ethernet port
-
-
LED Indicators
The following table describes the meanings of LED indicators on the front panels of
Hillstone devices.
Table 1-19: Front Panel LED Descriptions
LED
Color/Status
Description
PWR
Green/Always
on
The device power is running normally.
Orange/Always
on
The device power is running abnormally.
Red/Always on
Power failure so the system is down.
Off
The device is powered off.
STA
Green/Always
on
The system is booting.
Green/Blinking
The system is running normally.
Red/Always on
The system has failed to boot or has an error.
ALM
Red/Always on
The system is sending alarm(s).
Green/Blinking
The system is waiting.
Orange/Blinking
The system is using a trial license.